The DOI matches its Crossref record; 28 of the 28 references it cites were found in a registry or an index.
Comparison of physical and mechanical properties of PLA, ABS and nylon 6 fabricated using fused deposition modeling and injection molding
Abstract
The objective of this study was to compare the physical and mechanical performance of poly(lactic acid) (PLA), acrylonitrile butadiene styrene (ABS), and nylon 6 fabricated using fused deposition modeling (FDM) and conventional injection molding. It is found that different processing methods did not affect the viscosity of the samples, and the percentage difference for the density measurement is less than 4%. Water absorption of FDM samples is approximately 108% higher compared to those fabricated using the injection molding. The results also revealed that the FDM method did not strongly affect the degree of crystallinity of ABS, but it increased the degree of crystallinity of PLA and nylon 6. The tensile strength, Young's modulus, elongation at break, and impact strength of FDM samples were approximately 48%, 50%, 48%, and 78%, lower compared with the injection molded samples. The results presented can provide a guide to manufacturing the final products using FDM with the desired performance.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Additive manufacturing (3D printing): A review of materials, methods, applications and challenges
Ngo, T. D., Kashani, A., Imbalzano, G., Nguyen, K. T. Q., & Hui, D. (2018) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2018.02.012 · Cited by 8,431
3D printing of polymer matrix composites: A review and prospective
Wang, X., Jiang, M., Zhou, Z., Gou, J., & Hui, D. (2017) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2016.11.034 · Cited by 3,325
3-D printing: The new industrial revolution
Berman, B. (2012) · Business Horizons · doi:10.1016/j.bushor.2011.11.003 · Cited by 2,481
3D printing with polymers: Challenges among expanding options and opportunities
Stansbury, J. W., & Idacavage, M. J. (2016) · Dental Materials · doi:10.1016/j.dental.2015.09.018 · Cited by 1,732
Mohamed, O. A., Masood, S. H., & Bhowmik, J. L. (2015) · Advances in Manufacturing · doi:10.1007/s40436-014-0097-7 · Cited by 1,481
Fundamentals and applications of 3D printing for novel materials
Lee, J.-Y., An, J., & Chua, C. K. (2017) · Applied Materials Today · doi:10.1016/j.apmt.2017.02.004 · Cited by 1,354
Parametric appraisal of mechanical property of fused deposition modelling processed parts
Sood, A. K., Ohdar, R. K., & Mahapatra, S. S. (2010) · Materials & Design · doi:10.1016/j.matdes.2009.06.016 · Cited by 1,318
Effect of processing conditions on the bonding quality of FDM polymer filaments
Sun, Q., Rizvi, G. M., Bellehumeur, C. T., & Gu, P. (2008) · Rapid Prototyping Journal · doi:10.1108/13552540810862028 · Cited by 1,277
Tymrak, B. M., Kreiger, M., & Pearce, J. M. (2014) · Materials & Design · doi:10.1016/j.matdes.2014.02.038 · Cited by 1,244
The Role of Additive Manufacturing in the Era of Industry 4.0
Dilberoglu, U. M., Gharehpapagh, B., Yaman, U., & Dolen, M. (2017) · Procedia Manufacturing · doi:10.1016/j.promfg.2017.07.148 · Cited by 1,000
Zhang, J., Tashiro, K., Tsuji, H., & Domb, A. J. (2008) · Macromolecules · doi:10.1021/ma0706071 · Cited by 913
Wu, W., Geng, P., Li, G., Zhao, D., Zhang, H., & Zhao, J. (2015) · Materials · doi:10.3390/ma8095271 · Cited by 881
Lanzotti, A., Grasso, M., Staiano, G., & Martorelli, M. (2015) · Rapid Prototyping Journal · doi:10.1108/rpj-09-2014-0135 · Cited by 684
Weng, Z., Wang, J., Senthil, T., & Wu, L. (2016) · Materials & Design · doi:10.1016/j.matdes.2016.04.045 · Cited by 609
Dependence of mechanical properties of polyamide components on build parameters in the SLS process
Caulfield, B., McHugh, P. E., & Lohfeld, S. (2007) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2006.09.007 · Cited by 598
Rodríguez-Panes, A., Claver, J., & Camacho, A. M. (2018) · Materials · doi:10.3390/ma11081333 · Cited by 477
Rankouhi, B., Javadpour, S., Delfanian, F., & Letcher, T. (2016) · Journal of Failure Analysis and Prevention · doi:10.1007/s11668-016-0113-2 · Cited by 457
Melnikova, R., Ehrmann, A., & Finsterbusch, K. (2014) · IOP Conference Series Materials Science and Engineering · doi:10.1088/1757-899x/62/1/012018 · Cited by 326
Improving the impact strength of Poly(lactic acid) (PLA) in fused layer modeling (FLM)
Wang, L., Gramlich, W. M., & Gardner, D. J. (2017) · Polymer · doi:10.1016/j.polymer.2017.03.011 · Cited by 310
Omar, O. M., MOHAMED, M., SyedH., Masood, ., & Bhowmik (2015) · Acta Scientiarum Naturalium Universitatis Sunyatseni · Cited by 302
Torrado, A. R., & Roberson, D. A. (2016) · Journal of Failure Analysis and Prevention · doi:10.1007/s11668-016-0067-4 · Cited by 291
Is 3D printing safe? Analysis of the thermal treatment of thermoplastics: ABS, PLA, PET, and nylon
Wojtyła, S., Klama, P., & Baran, T. (2017) · Journal of Occupational and Environmental Hygiene · doi:10.1080/15459624.2017.1285489 · Cited by 288
Benwood, C., Anstey, A., Andrzejewski, J., Misra, M., & Mohanty, A. K. (2018) · ACS Omega · doi:10.1021/acsomega.8b00129 · Cited by 262
Onwubolu, G. C., & Rayegani, F. (2014) · International Journal of Manufacturing Engineering · doi:10.1155/2014/598531 · Cited by 252
Holland, S., Foster, T., MacNaughtan, W., & Tuck, C. J. (2017) · Journal of Food Engineering · doi:10.1016/j.jfoodeng.2017.06.008 · Cited by 155
Tensile Properties of Processed FDM Polycarbonate Material
Masood, S. H., Mau, K., & Song, W. (2010) · Materials science forum · doi:10.4028/www.scientific.net/msf.654-656.2556 · Cited by 153
3D PRINTING OF ANISOTROPIC METAMATERIALS
Garcia, C. R., Correa, J. I. C., Espalin, D., Barton, J. H., Rumpf, R. C., Wicker, R. B., & González, V. (2012) · Progress In Electromagnetics Research Letters · doi:10.2528/pierl12070311 · Cited by 143
Horvath, J. C. (2014) · Apress eBooks · doi:10.1007/978-1-4842-0025-4 · Cited by 85
Cited by
Wickramasinghe, S., Do, T., & Tran, P. (2020) · Polymers · doi:10.3390/polym12071529 · Cited by 1,052
Fused deposition modeling: process, materials, parameters, properties, and applications
Rajan, K., Samykano, M., Kadirgama, K., Harun, W. S. W., & Rahman, M. M. (2022) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-022-08860-7 · Cited by 426
Kassab, A., Al Nabhani, D., Mohanty, P., Pannier, C., & Ayoub, G. Y. (2023) · Polymers · doi:10.3390/polym15193881 · Cited by 141
Metadata
- Authors
- Lay, M., Thajudin, N. L. N., Hamid, Z. A. A., Rusli, A., Abdullah, M. K., & Shuib, R. K.
- Venue
- Composites Part B: Engineering
- Publisher
- Elsevier BV
- Published
- 2019-11
- Volume
- 176
- Pages
- 107341
- ISSN
- 1359-8368 (ISSN-L)
- OpenAlex
- W2967566376
- Cited by
- 393
- References
- 28
- FWCI
- 15.34
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.