The DOI matches its Crossref record; 10 of the 10 references it cites were found in a registry or an index.
Is 3D printing safe? Analysis of the thermal treatment of thermoplastics: ABS, PLA, PET, and nylon
Abstract
The fast development of low-cost desktop three-dimensional (3D) printers has made those devices widely accessible for goods manufacturing at home. However, is it safe? Users may belittle the effects or influences of pollutants (organic compounds and ultrafine particles) generated by the devices in question. Within the scope of this study, the authors attempt to investigate thermal decomposition of the following commonly used, commercially available thermoplastic filaments: acrylonitrile-butadiene-styrene (ABS), polylactic acid (PLA), polyethylene terephthalate (PET), and nylon. Thermogravimetric analysis has shown the detailed thermal patterns of their behavior upon increasing temperature in neutral atmosphere, while GC analysis of organic vapors emitted during the process of heating thermoplastics have made it possible to obtain crucial pieces of information about the toxicity of 3D printing process. The conducted study has shown that ABS is significantly more toxic than PLA. The emission of volatile organic compounds (VOC) has been in the range of 0.50 µmol/h. Styrene has accounted for more than 30% of total VOC emitted from ABS, while for PLA, methyl methacrylate has been detected as the predominant compound (44% of total VOCs emission). Moreover, the authors have summarized available or applicable methods that can eliminate formed pollutants and protect the users of 3D printers. This article summarizes theoretical knowledge on thermal degradation of polymers used for 3D printers and shows results of authors' investigation, as well as presents forward-looking solutions that may increase the safety of utilization of 3D printers.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Poly‐Lactic Acid: Production, Applications, Nanocomposites, and Release Studies
Jamshidian, M., Tehrany, E. A., Imran, M., Jacquot, M., & Desobry, S. (2010) · Comprehensive Reviews in Food Science and Food Safety · doi:10.1111/j.1541-4337.2010.00126.x · Cited by 1,557
Combustion-derived nanoparticles: A review of their toxicology following inhalation exposure
Donaldson, K., Tran, L., Jimenez, L. A., Duffin, R., Newby, D. E., Mills, N., MacNee, W., & Stone, V. (2005) · Particle and Fibre Toxicology · doi:10.1186/1743-8977-2-10 · Cited by 926
Ultrafine particle emissions from desktop 3D printers
Stephens, B., Azimi, P., El Orch, Z., & Ramos, T. (2013) · Atmospheric Environment · doi:10.1016/j.atmosenv.2013.06.050 · Cited by 488
Azimi, P., Zhao, D., Pouzet, C., Crain, N. E., & Stephens, B. (2016) · Environmental Science & Technology · doi:10.1021/acs.est.5b04983 · Cited by 389
Emissions of Nanoparticles and Gaseous Material from 3D Printer Operation
Kim, Y., Yoon, C., Ham, S., Park, J., Kim, S., Kwon, O., & Tsai, P.-J. (2015) · Environmental Science & Technology · doi:10.1021/acs.est.5b02805 · Cited by 220
Rutkowski, J. V., & Levin, B. C. (1986) · Fire and Materials · doi:10.1002/fam.810100303 · Cited by 159
Srivatsan, T. S., & Sudarshan, T. S. (2015) · CRC Press eBooks · doi:10.1201/b19360 · Cited by 151
Airborne Emissions of Carcinogens and Respiratory Sensitizers during Thermal Processing of Plastics
Unwin, J., Coldwell, M., Keen, C., & McAlinden, J. J. (2012) · The Annals of Occupational Hygiene · doi:10.1093/annhyg/mes078 · Cited by 88
Horvath, J. C. (2014) · Apress eBooks · doi:10.1007/978-1-4842-0025-4 · Cited by 85
Izdebska‐Podsiadły, J. (2015) · Elsevier eBooks · doi:10.1016/b978-0-323-37468-2.00001-4 · Cited by 68
Cited by
Recent Progress on Polymer Materials for Additive Manufacturing
Tan, L. J., Zhu, W., & Zhou, K. (2020) · Advanced Functional Materials · doi:10.1002/adfm.202003062 · Cited by 740
Kafle, A., Luis, E., Silwal, R., Pan, H. M., Shrestha, P. L., & Bastola, A. K. (2021) · Polymers · doi:10.3390/polym13183101 · Cited by 587
Recent Developments in Fused Deposition Modeling-Based 3D Printing of Polymers and Their Composites
Rahim, T. N. A. T., Abdullah, A. M., & Md Akil, H. (2019) · Polymer Reviews · doi:10.1080/15583724.2019.1597883 · Cited by 452
Lay, M., Thajudin, N. L. N., Hamid, Z. A. A., Rusli, A., Abdullah, M. K., & Shuib, R. K. (2019) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2019.107341 · Cited by 393
3D printing filament as a second life of waste plastics—a review
Mikula, K., Skrzypczak, D., Izydorczyk, G., Warchoł, J., Moustakas, K., Chojnacka, K., & Witek-Krowiak, A. (2021) · Environmental Science and Pollution Research · doi:10.1007/s11356-020-10657-8 · Cited by 382
Metadata
- Authors
- Wojtyła, S., Klama, P., & Baran, T.
- Venue
- Journal of Occupational and Environmental Hygiene
- Publisher
- Informa UK Limited
- Published
- 2017-05-04
- Volume
- 14
- Issue
- 6
- Pages
- D80-D85
- ISSN
- 1545-9624 (ISSN-L)
- 1545-9632
- OpenAlex
- W2586488856
- Cited by
- 288
- References
- 10
- FWCI
- 14.32
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Is 3D printing safe? Analysis of the thermal treatment of thermoplastics: ABS, PLA, PET, and nylon. https://app.cochat.ai/papers/10.1080/15459624.2017.1285489
- The paper
- Wojtyła, S., Klama, P., & Baran, T. (2017). Is 3D printing safe? Analysis of the thermal treatment of thermoplastics: ABS, PLA, PET, and nylon. Journal of Occupational and Environmental Hygiene. https://doi.org/10.1080/15459624.2017.1285489
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.