The DOI matches its Crossref record; 36 of the 36 references it cites were found in a registry or an index.
Cellulose, xylan and lignin interactions during pyrolysis of lignocellulosic biomass
Open accessAbstract
The three primary lignocellulosic biomass components (cellulose, xylan and lignin), synthetic biomass samples (prepared by mixing the three primary components) and lignocellulosic biomass (oak, spruce and pine) were pyrolysed in a thermogravimetric analyser and a wire mesh reactor. Different reactivities were observed between the three biomass components. Cellulose mainly produced condensables and was less dependent on heating rate, while xylan and lignin contributed most char yields and were significantly affected by heating rate. While xylan and lignin pyrolysed over a large temperature range and showed the behaviour characteristic of solid fuels, cellulose decomposition is sharp in a narrow temperature range, a behaviour typical of linear polymers. Comparison of the pyrolysis behaviour of individual components with that of their synthetic mixtures showed that interactions between cellulose and the other two components take place, but no interaction was found between xylan and lignin. No obvious interaction occurred for synthetic mixtures and lignocellulosic biomass at 325 °C, before the beginning of cellulose pyrolysis, in slow and high heating rate. At higher pyrolysis temperatures, more char was obtained for synthetic mixtures containing cellulose compared to the estimated value based on the individual components and their proportions in the mixture. For lignocellulosic biomass, less char and more tar were obtained than predicted from the components, which may be associated with the morphology of samples. The porous structure of lignocellulosic biomass provided a release route for pyrolysis vapours.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Characteristics of hemicellulose, cellulose and lignin pyrolysis
Yang, H., Yan, R., Chen, H., Lee, D. H., & Zheng, C. (2007) · Fuel · doi:10.1016/j.fuel.2006.12.013 · Cited by 8,155
Determination of Structural Carbohydrates and Lignin in Biomass
Sluiter, A. D., Hames, B. R., Ruiz, R. O., Scarlata, C. J., Sluiter, J. B., Templeton, D. W., & Crocker, D. P. (2012) · Cited by 5,261
Collard, F.-X., & Blin, J. (2014) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2014.06.013 · Cited by 1,905
Handbook of Wood Chemistry and Wood Composites
(2005) · CRC Press eBooks · doi:10.1201/9780203492437 · Cited by 1,480
Limayem, A., & Ricke, S. C. (2012) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2012.03.002 · Cited by 1,416
Yang, H., Yan, R., Chen, H., Zheng, C., Lee, D. H., & Liang, D. T. (2006) · Energy & Fuels · doi:10.1021/ef0580117 · Cited by 1,171
Handbook of Wood Chemistry and Wood Composites
(2012) · CRC Press eBooks · doi:10.1201/b12487 · Cited by 917
Literature review of physical and chemical pretreatment processes for lignocellulosic biomass
Harmsen, P. F. H., Huijgen, W. J. J., Bermúdez, L. A., & Bakker, R. (2010) · Data Archiving and Networked Services (DANS) · Cited by 743
Conversion of Lignocellulosic Biomass to Nanocellulose: Structure and Chemical Process
Lee, H. V., Hamid, S. B. A., & Zain, S. K. (2014) · The Scientific World Journal · doi:10.1155/2014/631013 · Cited by 700
Pyrolysis characteristics of biomass and biomass components
Raveendran, K. (1996) · Fuel · doi:10.1016/0016-2361(96)00030-0 · Cited by 693
Study on the pyrolytic behaviour of xylan-based hemicellulose using TG–FTIR and Py–GC–FTIR
Shen, D. K., Gu, S., & Bridgwater, A. V. (2010) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2009.12.001 · Cited by 585
Top ten fundamental challenges of biomass pyrolysis for biofuels
Mettler, M. S., Vlachos, D. G., & Dauenhauer, P. J. (2012) · Energy & Environmental Science · doi:10.1039/c2ee21679e · Cited by 576
Product Distribution from the Fast Pyrolysis of Hemicellulose
Patwardhan, P. R., Brown, R. C., & Shanks, B. H. (2011) · ChemSusChem · doi:10.1002/cssc.201000425 · Cited by 463
Influence of the interaction of components on the pyrolysis behavior of biomass
Wang, S., Guo, X., Wang, K., & Luo, Z. (2011) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2011.02.006 · Cited by 446
Demirbas, A. (2007) · Fuel Processing Technology · doi:10.1016/j.fuproc.2007.01.010 · Cited by 411
Cellulose–Hemicellulose and Cellulose–Lignin Interactions during Fast Pyrolysis
Zhang, J., Choi, Y. S., Yoo, C. G., Kim, T. H., Brown, R. C., & Shanks, B. H. (2015) · ACS Sustainable Chemistry & Engineering · doi:10.1021/sc500664h · Cited by 339
Mettler, M. S., Mushrif, S. H., Paulsen, A. D., Javadekar, A. D., Vlachos, D. G., & Dauenhauer, P. J. (2012) · Energy Environ. Sci. · doi:10.1039/c1ee02743c · Cited by 322
Couhert, C., Commandre, J.-M., & Salvador, S. (2009) · Fuel · doi:10.1016/j.fuel.2008.09.019 · Cited by 277
Comparison of the thermal reactivities of isolated lignin and holocellulose during pyrolysis
Haykiri-Acma, H., Yaman, S., & Küçükbayrak, S. (2010) · Fuel Processing Technology · doi:10.1016/j.fuproc.2010.02.009 · Cited by 171
Solid/liquid- and vapor-phase interactions between cellulose- and lignin-derived pyrolysis products
Hosoya, T., Kawamoto, H., & Saka, S. (2009) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2008.11.028 · Cited by 159
The potential of microbial processes for lignocellulosic biomass conversion to ethanol: a review
Dionisi, D., Anderson, J. A., Aulenta, F., McCue, A. J., & Paton, G. I. (2014) · Journal of Chemical Technology & Biotechnology · doi:10.1002/jctb.4544 · Cited by 138
Characterization of tars from variable heating rate pyrolysis of maceral concentrates
Li, C., Bartle, K. D., & Kandiyoti, R. (1993) · Fuel · doi:10.1016/0016-2361(93)90368-c · Cited by 136
Cellulose-Lignin interactions during slow and fast pyrolysis
Hilbers, T. J., Wang, Z., Pecha, M. B., Westerhof, R. J. M., Kersten, S. R. A., Peláez-Samaniego, M. R., & Garcìa-Pèrez, M. (2015) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2015.05.020 · Cited by 117
Cellulose-lignin interactions during fast pyrolysis with different temperatures and mixing methods
Wu, S., Shen, D., Hu, J., Zhang, H., & Xiao, R. (2016) · Biomass and Bioenergy · doi:10.1016/j.biombioe.2016.04.012 · Cited by 116
Effect of the Fast Pyrolysis Temperature on the Primary and Secondary Products of Lignin
Zhou, S., Garcìa-Pèrez, M., Pecha, M. B., Kersten, S. R. A., McDonald, A. G., & Westerhof, R. J. M. (2013) · Energy & Fuels · doi:10.1021/ef4001677 · Cited by 102
Fast pyrolysis in a novel wire-mesh reactor: Decomposition of pine wood and model compounds
Hoekstra, E., van Swaaij, W. P. M., Kersten, S. R. A., & Hogendoorn, K. J. A. (2012) · Chemical Engineering Journal · doi:10.1016/j.cej.2012.01.118 · Cited by 98
Vacuum pyrolysis of maceral concentrates in a wire-mesh reactor
Li, C., Bartle, K. D., & Kandiyoti, R. (1993) · Fuel · doi:10.1016/0016-2361(93)90001-i · Cited by 96
Relationship between thermal behaviour of lignocellulosic components and properties of biomass
Pang, C. H., Gaddipatti, S., Tucker, G. A., Lester, E. H., & Wu, T. (2014) · Bioresource Technology · doi:10.1016/j.biortech.2014.09.042 · Cited by 87
Fushimi, C., Katayama, S., & Tsutsumi, A. (2009) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2009.04.008 · Cited by 70
Bai, X., Johnston, P. A., & Brown, R. C. (2012) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2012.10.012 · Cited by 67
Ray, M. J., Brereton, N. J. B., Shield, I. F., Karp, A., & Murphy, R. J. (2012) · BioEnergy Research · doi:10.1007/s12155-011-9177-8 · Cited by 61
Characterisation of coal and biomass based on kinetic parameter distributions for pyrolysis
Sonoyama, N., & Hayashi, J. (2012) · Fuel · doi:10.1016/j.fuel.2012.04.023 · Cited by 53
George, A., Morgan, T. J., & Kandiyoti, R. (2014) · Energy & Fuels · doi:10.1021/ef501459c · Cited by 47
Niu, M., Guang-jie, Z., & Alma, M. H. (2011) · 中国林业科技:英文版 · doi:10.1007/s11632-011-0109-7 · Cited by 44
Peacocke, G. V. C., Madrali, E. S., Li, C., Güell, A. J., Wu, F., Kandiyoti, R., & Bridgwater, A. V. (1994) · Biomass and Bioenergy · doi:10.1016/0961-9534(94)00055-x · Cited by 35
Li, Y. (2014) · uO Research (University of Ottawa) · doi:10.20381/ruor-3717 · Cited by 11
Cited by
Lignocellulosic biomass pyrolysis mechanism: A state-of-the-art review
Wang, S., Dai, G., Yang, H., & Luo, Z. (2017) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2017.05.004 · Cited by 2,595
A comprehensive review on the pyrolysis of lignocellulosic biomass
Dhyani, V., & Bhaskar, T. (2018) · Renewable Energy · doi:10.1016/j.renene.2017.04.035 · Cited by 1,545
Emerging technologies for the pretreatment of lignocellulosic biomass
Hassan, S. S., Williams, G. A., & Jaiswal, A. K. (2018) · Bioresource Technology · doi:10.1016/j.biortech.2018.04.099 · Cited by 835
Kumar, B., Bhardwaj, N., Agrawal, K., Chaturvedi, V., & Verma, P. (2020) · Fuel Processing Technology · doi:10.1016/j.fuproc.2019.106244 · Cited by 743
A Review of Recent Advances in Biomass Pyrolysis
Wang, G., Dai, Y., Yang, H., Xiong, Q., Wang, K., Zhou, J., Li, Y., & Wang, S. (2020) · Energy & Fuels · doi:10.1021/acs.energyfuels.0c03107 · Cited by 597
Metadata
- Authors
- Yu, J., Paterson, N., Blamey, J., & Millan, M.
- Venue
- Fuel
- Publisher
- Elsevier BV
- Published
- 2017-03
- Volume
- 191
- Pages
- 140-149
- ISSN
- 0016-2361 (ISSN-L)
- OpenAlex
- W2552265359
- Cited by
- 452
- References
- 36
- FWCI
- 13.53
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.