The DOI matches its Crossref record; 48 of the 48 references it cites were found in a registry or an index.
Comparison of alkali and silica sources in one-part alkali-activated blast furnace slag mortar
Open accessAbstract
Alkali-activated materials (AAMs) are one of the alternative low-CO 2 binders. One-part AAMs, (that is, mixing a solid precursor with a solid alkali activator and adding water) have recently attracted increasing interest. The purpose of this study is to examine if fast-dissolving solid synthetic sodium metasilicate could be replaced by a combination of sodium hydroxide and slow-dissolving silica derived from rice husk ash or microsilica in the preparation of one-part alkali-activated blast furnace slag mortar. The replacement would improve the carbon footprint and the cost efficiency of the binder. The results demonstrate that silica availability significantly affects compressive strength development as a function of time or mixture composition. The highest compressive strength (107 MPa, 28 d) was obtained with fast-dissolving silica. Furthermore, setting times could be adjusted based on the mix composition, and the durability of mortar remained good after 120 freeze–thaw cycles. The results highlight the overall effect of silica availability on the fresh and hardened properties of one-part AAMs.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Scrivener, K. L., John, V. M., & Gartner, E. M. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2018.03.015 · Cited by 3,620
One-part alkali-activated materials: A review
Luukkonen, T., Abdollahnejad, Z., Yliniemi, J., Kinnunen, P., & Illikainen, M. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2017.10.001 · Cited by 1,456
318-19 Building Code Requirements for Structural Concrete and Commentary
(2019) · American Concrete Institute eBooks · doi:10.14359/51716937 · Cited by 1,289
Alkali Activated Materials: State-of-the-Art Report, RILEM TC 224-AAM
(2014) · RILEM State-of-the-Art Reports · doi:10.1007/978-94-007-7672-2 · Cited by 906
Kumar, S., Kumar, R., & Mehrotra, S. P. (2010) · Journal of Materials Science · doi:10.1007/s10853-009-3934-5 · Cited by 807
Evolution of binder structure in sodium silicate-activated slag-metakaolin blends
Bernal, S. A., Provis, J. L., Rose, V., & Mejía de Gutierrez, R. (2011) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2010.09.004 · Cited by 786
Rice husk ash as an alternate source for active silica production
Della, V. P., Kühn, I., & Hotza, D. (2002) · Materials Letters · doi:10.1016/s0167-577x(02)00879-0 · Cited by 656
Role of slag in microstructural development and hardening of fly ash-slag geopolymer
Puligilla, S., & Mondal, P. (2012) · Cement and Concrete Research · doi:10.1016/j.cemconres.2012.10.004 · Cited by 593
Alonso, S., & Palomo, A. (2001) · Materials Letters · doi:10.1016/s0167-577x(00)00212-3 · Cited by 542
A review on alkaline activation: New analytical perspectives
Palomo, A., Krivenko, P., Garcia-Lodeiro, I., Kavalerova, E., Maltseva, O., & Fernández-Jiménez, A. (2014) · Materiales de Construcción · doi:10.3989/mc.2014.00314 · Cited by 501
Bernal, S. A., San Nicolas, R., Myers, R. J., Mejía de Gutiérrez, R., Puertas, F., van Deventer, J. S. J., & Provis, J. L. (2014) · Cement and Concrete Research · doi:10.1016/j.cemconres.2013.12.003 · Cited by 493
Review Processing, properties and applications of reactive silica from rice husk—an overview
Chandrasekhar, S., Satyanarayana, K. G., Pramada, P. N., Raghavan, P., & Gupta, T. N. (2003) · Journal of Materials Science · doi:10.1023/a:1025157114800 · Cited by 486
Puertas, F., & Torres-Carrasco, M. (2014) · Cement and Concrete Research · doi:10.1016/j.cemconres.2013.12.005 · Cited by 420
In Situ ATR-FTIR Study of the Early Stages of Fly Ash Geopolymer Gel Formation
Rees, C. A., Provis, J. L., Lukey, G. C., & van Deventer, J. S. J. (2007) · Langmuir · doi:10.1021/la701185g · Cited by 411
Workability and mechanical properties of alkali activated slag concrete
Collins, F. G., & Sanjayan, J. G. (1999) · Cement and Concrete Research · doi:10.1016/s0008-8846(98)00236-1 · Cited by 400
An overview of geopolymers derived from industrial by-products
Mehta, A., & Siddique, R. (2016) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2016.09.136 · Cited by 391
Utilization of silica fume in concrete: Review of durability properties
Khan, M. I., & Siddique, R. (2011) · Resources, Conservation and Recycling · doi:10.1016/j.resconrec.2011.09.016 · Cited by 373
Structural reorganisation of class F fly ash in alkaline silicate solutions
Lee, W. K. W., & van Deventer, J. S. J. (2002) · Colloids and Surfaces A Physicochemical and Engineering Aspects · doi:10.1016/s0927-7757(02)00237-6 · Cited by 363
Minimising the global warming potential of clay based geopolymers
Heath, A., Paine, K., & McManus, M. (2014) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2014.04.046 · Cited by 352
Isothermal calorimetry and in-situ XRD study of the NaOH activated fly ash, metakaolin and slag
Sun, Z., & Vollpracht, A. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2017.10.004 · Cited by 320
Properties of cementless mortars activated by sodium silicate
Yang, K.-H., Song, J.-K., Ashour, A. F., & Lee, E.-T. (2008) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2007.07.003 · Cited by 319
Microcracking and strength development of alkali activated slag concrete
Collins, F., & Sanjayan, J. G. (2001) · Cement and Concrete Composites · doi:10.1016/s0958-9465(01)00003-8 · Cited by 316
The effect of silica availability on the mechanism of geopolymerisation
Hajimohammadi, A., Provis, J. L., & van Deventer, J. S. J. (2011) · Cement and Concrete Research · doi:10.1016/j.cemconres.2011.02.001 · Cited by 279
Combustion behaviour of rice husk in a bubbling fluidised bed
Armesto, L., Bahillo, A., Veijonen, K., Cabanillas, A., & Otero, J. (2002) · Biomass and Bioenergy · doi:10.1016/s0961-9534(02)00046-6 · Cited by 250
One-Part Geopolymer Mixes from Geothermal Silica and Sodium Aluminate
Hajimohammadi, A., Provis, J. L., & van Deventer, J. S. J. (2008) · Industrial & Engineering Chemistry Research · doi:10.1021/ie8006825 · Cited by 239
Kamseu, E., Beleuk à Moungam, L. M., Cannio, M., Billong, N., Chaysuwan, D., Melo, U. C., & Leonelli, C. (2017) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2016.10.164 · Cited by 227
Passuello, A., Rodríguez, E. D., Hirt, E., Longhi, M., Bernal, S. A., Provis, J. L., & Kirchheim, A. P. (2017) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2017.08.007 · Cited by 223
Synthesizing one-part geopolymers from rice husk ash
Sturm, P., Gluth, G. J. G., Brouwers, H. J. H., & Kühne, H.-C. (2016) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2016.08.017 · Cited by 200
Sustainable alkali activated materials: Precursor and activator derived from industrial wastes
Fernández‐Jiménez, A., Cristelo, N., Miranda, T. F. D. S., & Palomo, A. (2017) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2017.06.151 · Cited by 187
Compressive strength of one-part alkali activated fly ash using red mud as alkali supplier
Choo, H., Lim, S., Lee, W., & Lee, C. (2016) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2016.08.015 · Cited by 178
A novel method to produce dry geopolymer cement powder
Abdel-Gawwad, H. A., & Abo-El-Enein, S. A. (2016) · HBRC Journal · doi:10.1016/j.hbrcj.2014.06.008 · Cited by 176
Dissolution behaviour of source materials for synthesis of geopolymer binders: A kinetic approach
Hajimohammadi, A., & van Deventer, J. S. J. (2016) · International Journal of Mineral Processing · doi:10.1016/j.minpro.2016.05.014 · Cited by 162
Alkali activated slag foams: The effect of the alkali reaction on foam characteristics
Hajimohammadi, A., Ngo, T., Mendis, P. A., Kashani, A., & van Deventer, J. S. J. (2017) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2017.01.134 · Cited by 157
Mechanochemical synthesis of one-part alkali aluminosilicate hydraulic cement
Matalkah, F., Xu, L., Wu, W., & Soroushian, P. (2016) · Materials and Structures · doi:10.1617/s11527-016-0968-4 · Cited by 137
Studies in ultrasonic pulse velocity of concrete containing GGBFS
Shariq, M., Prasad, J., & Masood, A. (2012) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2012.11.070 · Cited by 123
Alkali activated slag cements using waste glass as alternative activators. Rheological behaviour
Torres‐Carrasco, M., Rodríguez-Puertas, C., Alonso, M. M., & Puertas, F. (2015) · Boletín de la Sociedad Española de Cerámica y Vidrio · doi:10.1016/j.bsecv.2015.03.004 · Cited by 114
Potassium-rich biomass ashes as activators in metakaolin-based inorganic polymers
Peys, A., Rahier, H., & Pontikes, Y. (2015) · Applied Clay Science · doi:10.1016/j.clay.2015.11.003 · Cited by 107
Suwan, T., & Fan, M. (2016) · Materials and Manufacturing Processes · doi:10.1080/10426914.2016.1198013 · Cited by 103
Binder Chemistry – Low-Calcium Alkali-Activated Materials
Provis, J. L., Fernández‐Jiménez, A., Kamseu, E., Leonelli, C., & Palomo, A. (2013) · RILEM state-of-the-art reports · doi:10.1007/978-94-007-7672-2_4 · Cited by 101
Why Alkaline Activation – 60 Years of the Theory and Practice of Alkali-Activated Materials
prospect, P., & Ukraine, K. (2017) · Journal of ceramic science and technology · Cited by 92
Sturm, P., Gluth, G. J. G., Simon, S., Brouwers, H. J. H., & Kühne, H. (2016) · Thermochimica Acta · doi:10.1016/j.tca.2016.04.015 · Cited by 87
Preparation of drying powder inorganic polymer cement based on alkali-activated slag technology
Wang, K.-T., Du, L.-Q., Lv, X., He, Y., & Cui, X. (2017) · Powder Technology · doi:10.1016/j.powtec.2017.02.036 · Cited by 85
Solid Reactant-Based Geopolymers from Rice Hull Ash and Sodium Aluminate
Hajimohammadi, A., & van Deventer, J. S. J. (2016) · Waste and Biomass Valorization · doi:10.1007/s12649-016-9735-6 · Cited by 77
Durability of Alkali-Activated Slag Concretes Prepared Using Waste Glass as Alternative Activator
Torres‐Carrasco, M., Tognonvi, M. T., Tagnit‐Hamou, A., & Puertas, F. (2015) · ACI Materials Journal · doi:10.14359/51687903 · Cited by 71
Provis, J. L. (2013) · RILEM state-of-the-art reports · doi:10.1007/978-94-007-7672-2_1 · Cited by 66
Peys, A., Arnout, L., Blanpain, B., Rahier, H., Acker, K. V., & Pontikes, Y. (2017) · Waste and Biomass Valorization · doi:10.1007/s12649-017-9877-1 · Cited by 59
Dry powder alkali-activated slag cements
Kovtun, M., Kearsley, E. P., & Shekhovtsova, J. (2015) · Advances in Cement Research · doi:10.1680/jadcr.14.00078 · Cited by 51
Glass Phase Structure of Blast Furnace Slag
Li, C., Sun, H. H., & Li, L. T. (2010) · Advanced materials research · doi:10.4028/www.scientific.net/amr.168-170.3 · Cited by 27
Cited by
Recent progress in low-carbon binders
Shi, C., Qu, B., & Provis, J. L. (2019) · Cement and Concrete Research · doi:10.1016/j.cemconres.2019.05.009 · Cited by 714
Silica fume and waste glass in cement concrete production: A review
Mehta, A., & Ashish, D. K. (2020) · Journal of Building Engineering · doi:10.1016/j.jobe.2019.100888 · Cited by 438
Wang, R., Hu, Z., Li, Y., Wang, K., & Zhang, H. (2022) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2022.126371 · Cited by 410
Synthesis and characterization of one-part geopolymers for extrusion based 3D concrete printing
Panda, B., Singh, G. B., Unluer, C., & Tan, M. J. (2019) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2019.02.185 · Cited by 254
Metadata
- Authors
- Luukkonen, T., Abdollahnejad, Z., Yliniemi, J., Kinnunen, P., & Illikainen, M.
- Venue
- Journal of Cleaner Production
- Publisher
- Elsevier BV
- Published
- 2018-06
- Volume
- 187
- Pages
- 171-179
- ISSN
- 0959-6526 (ISSN-L)
- OpenAlex
- W2793427184
- Cited by
- 261
- References
- 48
- FWCI
- 19.53
- Type
- journal article
- Language
- en
- Open access
- hybrid
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.