The DOI matches its Crossref record; 43 of the 43 references it cites were found in a registry or an index.
Preparation of cleaner one-part geopolymer by investigating different types of commercial sodium metasilicate in China
Abstract
Abstract One-part geopolymers prepared by powder activators, similar to Portland cement in cast-in-situ application, are promising building materials due to the relatively slighter embodied environmental impact. There are three types of commercial sodium metasilicate powders in the China market, and they are Na2SiO3-anhydrous/NS0, Na2SiO3·5H2O/NS5 and Na2SiO3·9H2O/NS9, respectively. This study employed ultra-fine fly ash sinking beads (FASB) and ground granulated blast furnace slag (GGBS) as precursor materials to analyze the influences of NS0, NS5 and NS9 on the properties, microstructure and environmental impact of one-part geopolymer by measuring and characterizing compressive strength, porosity, reaction heat release, geopolymerization products and carbon dioxide equivalent (CO2-e) emission. The experimental results indicate that NS0 has the most rapid and effective activated effect in both single GGBS and GGBS-FASB composites. The strength of geopolymer activated with NS0 is the highest, followed by that with NS9, and followed by that with NS5. The products are mainly gelatinous phases, and the gels in NS0 and NS9 activated geopolymers are better geopolymerized than those in NS5 activated geopolymer, which is proved to be responsible for the difference in macro-performance. The evaluations of the cost and CO2-e emission per MPa of one-part geopolymer demonstrate that NS0 and NS9 are much cheaper and cleaner than NS5 for preparing one-part geopolymer. The embodied CO2 indexes of NS0 and NS9 activated single GGBS are only about 26.5% and 34.0% of that of ordinary Portland cement. This study not only partially explains the reasons for the different properties of one-part geopolymer activated by different types of sodium metasilicate, but also provides a guidance for preparing one-part geopolymer with reasonable cost and slight environmental impact.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Carbon dioxide equivalent (CO2-e) emissions: A comparison between geopolymer and OPC cement concrete
Turner, L. K., & Collins, F. G. (2013) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2013.01.023 · Cited by 2,411
Geopolymer Chemistry and Applications
Davidovits, J. (2008) · CERN Document Server (European Organization for Nuclear Research) · Cited by 1,692
Geopolymer concrete: A review of some recent developments
Singh, B., Ishwarya, G., Gupta, M., & Bhattacharyya, S. K. (2015) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2015.03.036 · Cited by 1,484
One-part alkali-activated materials: A review
Luukkonen, T., Abdollahnejad, Z., Yliniemi, J., Kinnunen, P., & Illikainen, M. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2017.10.001 · Cited by 1,456
Alkali-Activated Cements and Concretes
Shi, C., Krivenko, P. V., & Roy, D. (2006) · Taylor & Francis eBooks · doi:10.4324/9780203390672 · Cited by 1,164
Fly ash-based geopolymer: clean production, properties and applications
Zhuang, X. Y., Chen, L., Komarneni, S., Zhou, C. H., Tong, D. S., Yang, H. M., Yu, W. H., & Wang, H. (2016) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2016.03.019 · Cited by 1,020
NaOH-activated ground fly ash geopolymer cured at ambient temperature
Somna, K., Jaturapitakkul, C., Kajitvichyanukul, P., & Chindaprasirt, P. (2011) · Fuel · doi:10.1016/j.fuel.2011.01.018 · Cited by 995
Influence of calcium compounds on the mechanical properties of fly ash geopolymer pastes
Temuujin, J., van Riessen, A., & Williams, R. (2009) · Journal of Hazardous Materials · doi:10.1016/j.jhazmat.2008.12.121 · Cited by 834
Hemalatha, T., & Ramaswamy, A. (2017) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2017.01.114 · Cited by 799
Gartner, E., & Hirao, H. (2015) · Cement and Concrete Research · doi:10.1016/j.cemconres.2015.04.012 · Cited by 607
(Micro)-structural comparison between geopolymers, alkali-activated slag cement and Portland cement
Lecomte, I., Henrist, C., Liégeois, M., Maseri, F., Rulmont, A., & Cloots, R. (2006) · Journal of the European Ceramic Society · doi:10.1016/j.jeurceramsoc.2005.12.021 · Cited by 597
Cement industry greenhouse gas emissions – management options and abatement cost
Kajaste, R., & Hurme, M. (2016) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2015.07.055 · Cited by 584
Walkley, B., San Nicolas, R., Sani, M.-A., Rees, G. J., Hanna, J. V., van Deventer, J. S. J., & Provis, J. L. (2016) · Cement and Concrete Research · doi:10.1016/j.cemconres.2016.08.010 · Cited by 544
Kim, M. S., Jun, Y., Lee, C., & Oh, J. E. (2013) · Cement and Concrete Research · doi:10.1016/j.cemconres.2013.09.011 · Cited by 518
Nath, P., & Sarker, P. K. (2014) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2014.08.008 · Cited by 477
Geopolymer mortars as sustainable repair material: A comprehensive review
Fahim Huseien, G., Mirza, J., Ismail, M., Ghoshal, S. K., & Abdulameer Hussein, A. (2017) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2017.05.076 · Cited by 462
Phoo-ngernkham, T., Chindaprasirt, P., Sata, V., Hanjitsuwan, S., & Hatanaka, S. (2014) · Materials & Design · doi:10.1016/j.matdes.2013.09.049 · Cited by 452
Abdalqader, A. F., Jin, F., & Al-Tabbaa, A. (2016) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2015.12.010 · Cited by 444
Nematollahi, B., Sanjayan, J., & Shaikh, F. U. A. (2015) · Ceramics International · doi:10.1016/j.ceramint.2014.12.154 · Cited by 426
Microstructural changes in alkali activated fly ash/slag geopolymers with sulfate exposure
Ismail, I., Bernal, S. A., Provis, J. L., Hamdan, S., & van Deventer, J. S. J. (2013) · Materials and Structures · doi:10.1617/s11527-012-9906-2 · Cited by 417
Concrete: An eco material that needs to be improved
Flatt, R. J., Roussel, N., & Cheeseman, C. R. (2012) · Journal of the European Ceramic Society · doi:10.1016/j.jeurceramsoc.2011.11.012 · Cited by 392
Variation in hybrid cements over time. Alkaline activation of fly ash–portland cement blends
García-Lodeiro, I., Fernández-Jiménez, A., & Palomo, A. (2013) · Cement and Concrete Research · doi:10.1016/j.cemconres.2013.03.022 · Cited by 385
Designing more sustainable and greener self-compacting concrete
Long, G., Gao, Y., & Xie, Y. (2015) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2015.02.072 · Cited by 359
Self-citationPerformance of alkali activated slag concrete mixes incorporating copper slag as fine aggregate
Mithun, B. M., & Narasimhan, M. C. (2015) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2015.06.026 · Cited by 342
Hydration and properties of sodium sulfate activated slag
Rashad, A. M., Bai, Y., Basheer, P. A. M., Milestone, N. B., & Collier, N. C. (2013) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2012.12.010 · Cited by 335
A thermodynamic model for C-(N-)A-S-H gel: CNASH_ss. Derivation and validation
Myers, R. J., Bernal, S. A., & Provis, J. L. (2014) · Cement and Concrete Research · doi:10.1016/j.cemconres.2014.07.005 · Cited by 312
Mechanical and microstructural characterization of geopolymers derived from red mud and fly ashes
Hu, W., Nie, Q., Huang, B., Shu, X., & He, Q. (2018) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2018.03.086 · Cited by 274
Thermal Activation of Albite for the Synthesis of One‐Part Mix Geopolymers
Feng, D., Provis, J. L., & van Deventer, J. S. J. (2012) · Journal of the American Ceramic Society · doi:10.1111/j.1551-2916.2011.04925.x · Cited by 244
Eco-mechanical index for structural concrete
Chiaia, B. M., Fantilli, A. P., Guerini, A., Volpatti, G., & Zampini, D. (2014) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2013.12.090 · Cited by 207
One-part geopolymer cement from slag and pretreated paper sludge
Adesanya, E., Ohenoja, K., Luukkonen, T., Kinnunen, P., & Illikainen, M. (2018) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2018.03.007 · Cited by 202
Factory-level measurements on CO2 emission factors of cement production in China
Shen, L., Gao, T., Zhao, J., Wang, L., Wang, L., Liu, L., Chen, F., & Xue, J. (2014) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2014.03.025 · Cited by 193
Nematollahi, B., Sanjayan, J., Qiu, J., & Yang, E.-H. (2017) · Archives of Civil and Mechanical Engineering · doi:10.1016/j.acme.2016.12.005 · Cited by 187
Durability and microstructure characteristics of alkali activated coal bottom ash geopolymer cement
Topçu, İ. B., Toprak, M. U., & Uygunoğlu, T. (2014) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2014.06.037 · Cited by 169
Evolution and projection of CO2 emissions for China's cement industry from 1980 to 2020
Gao, T., Shen, L., Shen, M., Liu, L., Chen, F., & Gao, L. (2017) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2017.02.006 · Cited by 164
Deir, E., Gebregziabiher, B. S., & Peethamparan, S. (2013) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2013.11.010 · Cited by 152
Mechanochemical synthesis of one-part alkali aluminosilicate hydraulic cement
Matalkah, F., Xu, L., Wu, W., & Soroushian, P. (2016) · Materials and Structures · doi:10.1617/s11527-016-0968-4 · Cited by 137
Hajimohammadi, A., Provis, J. L., & van Deventer, J. S. J. (2011) · Journal of Colloid and Interface Science · doi:10.1016/j.jcis.2011.02.045 · Cited by 130
Peng, M. X., Wang, Z. H., Shen, S. H., & Xiao, Q. G. (2014) · Materials and Structures · doi:10.1617/s11527-014-0350-3 · Cited by 109
Suwan, T., & Fan, M. (2016) · Materials and Manufacturing Processes · doi:10.1080/10426914.2016.1198013 · Cited by 103
Shekhovtsova, J., Zhernovsky, I. V., Kovtun, M., Kozhukhova, N. I., Zhernovskaya, I., & Kearsley, E. P. (2018) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2017.12.270 · Cited by 91
Xia, Y., Yan, Y., & Hu, Z. (2013) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2013.06.033 · Cited by 88
Properties of alkali-activated mortar and concrete using lightweight aggregates
Yang, K., Song, J., & Lee, J.-S. (2009) · Materials and Structures · doi:10.1617/s11527-009-9499-6 · Cited by 82
Assessment of the durability of grout submitted to accelerated carbonation test
Martins, R. O. G., Alvarenga, R. D. C. S. S., Pedroti, L. G., de Oliveira, A. F., Mendes, B. C., & de Azevedo, A. R. G. (2017) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2017.10.111 · Cited by 65
Cited by
Xiao, R., Ma, Y., Jiang, X., Zhang, M., Zhang, Y., Wang, Y., Huang, B., & He, Q. (2020) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2019.119610 · Cited by 359
Metadata
- Authors
- Ma, C., Long, G., Shi, Y., & Xie, Y.
- Venue
- Journal of Cleaner Production
- Publisher
- Elsevier BV
- Published
- 2018-11
- Volume
- 201
- Pages
- 636-647
- ISSN
- 0959-6526 (ISSN-L)
- OpenAlex
- W2887378826
- Cited by
- 253
- References
- 43
- FWCI
- 15.27
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.