Design and characterisation of food grade powders and inks for microstructure control using 3D printing
Open accessThe DOI matches its Crossref record; 3 of the 3 references it cites were found in a registry or an index.
Abstract
Additive Manufacturing techniques have been previously applied to food materials with direct consumption in mind, as opposed to creating structural ingredients as shown in this study. First, semi-crystalline cellulose was mechanically treated by ball milling to render an amorphous powder, which has been characterised. Requirements for the subsequent recrystallization of this powder with a view to structuring have been determined through the control of moisture and thermal energy. Food inks based on xanthan gum have been formulated to enable successful jetting with a FujiFilm Dimatix ink jet printer. The polymer inks were subsequently jetted onto the amorphous cellulose powder to observe powder-binder interactions. Material combinations and parameters were optimised to produce cohesive geometric structures. The results of this study are promising when looking towards using these materials in a binder jetting additive manufacturing technique using designer particles and inks to create structures for use in food products.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Gibson, I., Rosen, D., & Stucker, B. (2015) · doi:10.1007/978-1-4939-2113-3 · Cited by 3,299
An Overview of 3D Printing Technologies for Food Fabrication
Sun, J., Zhou, W., Huang, D., Fuh, J. Y. H., & Hong, G. S. (2015) · Food and Bioprocess Technology · doi:10.1007/s11947-015-1528-6 · Cited by 549
Extrusion-based food printing for digitalized food design and nutrition control
Sun, J., Zhou, W., Yan, L., Huang, D., & Lin, L.-Y. (2018) · Journal of Food Engineering · doi:10.1016/j.jfoodeng.2017.02.028 · Cited by 410
Cited by
Binder jet 3D printing—Process parameters, materials, properties, modeling, and challenges
Mostafaei, A., Elliott, A. M., Barnes, J. E., Li, F., Tan, W., Cramer, C. L., Nandwana, P., & Chmielus, M. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100707 · Cited by 1,093
Binder jetting: A review of process, materials, and methods
Ziaee, M., & Crane, N. B. (2019) · Additive Manufacturing · doi:10.1016/j.addma.2019.05.031 · Cited by 819
Chen, L.-Y., Liang, S.-X., Liu, Y., & Zhang, L.-C. (2021) · Materials Science and Engineering: R: Reports · doi:10.1016/j.mser.2021.100648 · Cited by 603
3D printing technology: The new era for food customization and elaboration
Dankar, I., Haddarah, A., Omar, F. E. L., Sepulcre, F., & Pujolà, M. (2018) · Trends in Food Science & Technology · doi:10.1016/j.tifs.2018.03.018 · Cited by 471
Lay, M., Thajudin, N. L. N., Hamid, Z. A. A., Rusli, A., Abdullah, M. K., & Shuib, R. K. (2019) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2019.107341 · Cited by 393
Metadata
- Authors
- Holland, S., Foster, T., MacNaughtan, W., & Tuck, C.
- Venue
- Journal of Food Engineering
- Publisher
- Elsevier BV
- Published
- 2018-03
- Volume
- 220
- Pages
- 12-19
- ISSN
- 0260-8774 (ISSN-L)
- OpenAlex
- W2718407264
- Cited by
- 148
- References
- 3
- FWCI
- 9.66
- Type
- journal article
- Language
- en
- Open access
- hybrid
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Design and characterisation of food grade powders and inks for microstructure control using 3D printing. https://app.cochat.ai/papers/10.1016/j.jfoodeng.2017.06.008
- The paper
- Holland, S., Foster, T., MacNaughtan, W., & Tuck, C. (2018). Design and characterisation of food grade powders and inks for microstructure control using 3D printing. Journal of Food Engineering. https://doi.org/10.1016/j.jfoodeng.2017.06.008
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.