The DOI matches its Crossref record; 34 of the 34 references it cites were found in a registry or an index.
3D printing of continuous flax fibre reinforced biocomposites for structural applications
Open accessAbstract
Recently, interest has been increasing in natural fibres as composite reinforcing fillers for polymer-based filaments manufactured with the Fused Deposition Modeling (FDM) process, despite their moderate mechanical properties compared to pure polymer. An innovative way was proposed in the present work to optimize the mechanical properties of biocomposites. It was based on novel continuous flax fibre/PLA (cFF/PLA) composite filaments made with a customized co-extrusion process and printed with a simple and affordable printing machine. The microstructure of the printed cFF/PLA biocomposite evidenced a homogeneous distribution of yarn within the cross section, while the twisted flax yarn led to fibre-rich areas at mesoscale. The cFF/PLA showed tensile modulus and strength values that exceeded the only available published result on continuous natural fibre printed composites by >4.5 times. Tensile properties were in the same range as those for continuous glass fibre/PolyAmide (PA) printed composites, paving the way for the use of biocomposites in structural applications. Their weakest point was their transverse properties that remained poorer than similar flax/PLA thermocompressed composites.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Additive manufacturing (3D printing): A review of materials, methods, applications and challenges
Ngo, T. D., Kashani, A., Imbalzano, G., Nguyen, K. T. Q., & Hui, D. (2018) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2018.02.012 · Cited by 8,431
Biocomposites reinforced with natural fibers: 2000–2010
Faruk, O., Bledzki, A. K., Fink, H.-P., & Sain, M. (2012) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2012.04.003 · Cited by 4,262
A review of recent developments in natural fibre composites and their mechanical performance
Pickering, K. L., Efendy, M. G. A., & Le, T. M. (2016) · Composites Part A: Applied Science and Manufacturing · doi:10.1016/j.compositesa.2015.08.038 · Cited by 3,479
3D printing of polymer matrix composites: A review and prospective
Wang, X., Jiang, M., Zhou, Z., Gou, J., & Hui, D. (2017) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2016.11.034 · Cited by 3,325
Mohanty, A. K., Misra, M., & Drzal, L. T. (2002) · Journal of Polymers and the Environment · doi:10.1023/a:1021013921916 · Cited by 2,151
Three-dimensional printing of continuous-fiber composites by in-nozzle impregnation
Matsuzaki, R., Ueda, M., Namiki, M., Jeong, T.-K., Asahara, H., Horiguchi, K., Nakamura, T., Todoroki, A., & Hirano, Y. (2016) · Scientific Reports · doi:10.1038/srep23058 · Cited by 1,171
Dickson, A. N., Barry, J. N., McDonnell, K. A., & Dowling, D. P. (2017) · Additive Manufacturing · doi:10.1016/j.addma.2017.06.004 · Cited by 792
Rapid prototyping of continuous carbon fiber reinforced polylactic acid composites by 3D printing
Li, N., Li, Y., & Liu, S. (2016) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2016.07.025 · Cited by 707
Recent Progress in Additive Manufacturing of Fiber Reinforced Polymer Composite
Goh, G. D., Yap, Y. L., Agarwala, S., & Yeong, W. Y. (2019) · Advanced Materials Technologies · doi:10.1002/admt.201800271 · Cited by 621
Goh, G. D., Dikshit, V., Nagalingam, A. P., Goh, G. L., Agarwala, S., Sing, S. L., Wei, J., & Yeong, W. Y. (2018) · Materials & Design · doi:10.1016/j.matdes.2017.10.021 · Cited by 604
Influence of processing and chemical treatment of flax fibres on their composites
de Weyenberg, I. V., Ivens, J., Coster, A. D., Kino, B., Baetens, E., & Verpoest, I. (2003) · Composites Science and Technology · doi:10.1016/s0266-3538(03)00093-9 · Cited by 586
Fracture Surface Analysis of 3D-Printed Tensile Specimens of Novel ABS-Based Materials
Torrado Perez, A. R., Roberson, D. A., & Wicker, R. B. (2014) · Journal of Failure Analysis and Prevention · doi:10.1007/s11668-014-9803-9 · Cited by 523
3D printing of wood fibre biocomposites: From mechanical to actuation functionality
Le Duigou, A., Castro, M., Bevan, R., & Martin, N. (2016) · Materials & Design · doi:10.1016/j.matdes.2016.02.018 · Cited by 523
Self-citation3D Printing of Continuous Carbon Fibre Reinforced Thermo-Plastic (CFRTP) Tensile Test Specimens
Der Klift, F. V., Koga, Y., Todoroki, A., Ueda, M., Hirano, Y., & Matsuzaki, R. (2016) · Open Journal of Composite Materials · doi:10.4236/ojcm.2016.61003 · Cited by 516
3D printing for continuous fiber reinforced thermoplastic composites: mechanism and performance
Yang, C., Tian, X., Liu, T., Cao, Y., & Li, D. (2017) · Rapid Prototyping Journal · doi:10.1108/rpj-08-2015-0098 · Cited by 515
Characterization of 3D printed long fibre reinforced composites
Justo, J., Távara, L., García-Guzmán, L., & París, F. (2018) · Composite Structures · doi:10.1016/j.compstruct.2017.11.052 · Cited by 473
Recycling and remanufacturing of 3D printed continuous carbon fiber reinforced PLA composites
Tian, X., Liu, T., Wang, Q., Dilmurat, A., Li, D., & Ziegmann, G. (2017) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2016.11.139 · Cited by 432
Effect of wood content in FDM filament on properties of 3D printed parts
Kariz, M., Sernek, M., Obućina, M., & Kuzman, M. K. (2018) · Materials Today Communications · doi:10.1016/j.mtcomm.2017.12.016 · Cited by 360
Material Property Testing of 3D-Printed Specimen in PLA on an Entry-Level 3D Printer
Letcher, T., & Waytashek, M. (2014) · Volume 2A: Advanced Manufacturing · doi:10.1115/imece2014-39379 · Cited by 325
Torrado, A. R., & Roberson, D. A. (2016) · Journal of Failure Analysis and Prevention · doi:10.1007/s11668-016-0067-4 · Cited by 291
Effect of flax fibres individualisation on tensile failure of flax/epoxy unidirectional composite
Coroller, G., Lefeuvre, A., Le Duigou, A., Bourmaud, A., Ausias, G., Gaudry, T., & Baley, C. (2013) · Composites Part A: Applied Science and Manufacturing · doi:10.1016/j.compositesa.2013.03.018 · Cited by 254
Self-citationSustainable composite fused deposition modelling filament using recycled pre-consumer polypropylene
Stoof, D., & Pickering, K. (2018) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2017.10.005 · Cited by 228
Chabaud, G., Castro, M., Denoual, C., & Le Duigou, A. (2019) · Additive Manufacturing · doi:10.1016/j.addma.2019.01.005 · Cited by 215
Self-citationMilosevic, M., Stoof, D., & Pickering, K. (2017) · Journal of Composites Science · doi:10.3390/jcs1010007 · Cited by 173
Impregnated fibre bundle test for natural fibres used in composites
Bensadoun, F., Verpoest, I., Baets, J., Müssig, J., Graupner, N., Davies, P., Gomina, M., Kervoëlen, A., & Baley, C. (2017) · Journal of Reinforced Plastics and Composites · doi:10.1177/0731684417695461 · Cited by 136
Tarrés, Q., Melbø, J. K., Delgado‐Aguilar, M., Espinach, F. X., Mutjé, P., & Chinga‐Carrasco, G. (2018) · Composites Part B Engineering · doi:10.1016/j.compositesb.2018.07.009 · Cited by 130
Bourmaud, A., Duigou, A. L., Gourier, C., & Baley, C. (2016) · Industrial Crops and Products · doi:10.1016/j.indcrop.2016.02.007 · Cited by 113
Natural fibres actuators for smart bio-inspired hygromorph biocomposites
Duigou, A. L., Réquilé, S., Beaugrand, J., Scarpa, F. L., & Castro, M. (2017) · Smart Materials and Structures · doi:10.1088/1361-665x/aa9410 · Cited by 97
Self-citation3D Printable Filaments Made of Biobased Polyethylene Biocomposites
Filgueira, D., Holmen, S., Melbø, J. K., Moldes, D., Echtermeyer, A. T., & Chinga‐Carrasco, G. (2018) · Polymers · doi:10.3390/polym10030314 · Cited by 77
Cadu, T., Berges, M., Sicot, O., Person, V., Piezel, B., Schoors, L. V., Placet, V., Corn, S., Léger, R., Divet, L., et al. (2018) · Composites Part B Engineering · doi:10.1016/j.compositesb.2018.04.059 · Cited by 55
About optimal architecture of plant fibre textile composite for mechanical and sorption properties
Cherif, Z. E., Poilâne, C., Vivet, A., Doudou, B. B., & Chen, J. (2016) · Composite Structures · doi:10.1016/j.compstruct.2015.12.030 · Cited by 46
A multi-scale study of the interface between natural fibres and a biopolymer
Duigou, A. L., Baley, C., Grohens, Y., Davies, P., Cognard, J., Créac’Hcadec, R., & Sohier, L. (2014) · Composites Part A Applied Science and Manufacturing · doi:10.1016/j.compositesa.2014.06.010 · Cited by 44
Sustainable Natural Bio Composite for FDM Feedstocks
Ibrahim, M., Ibrahim, M., Badrishah, N. S., Sa’ude, N., Ibrahim, M. H. I., & Ibrahim, M. H. I. (2014) · Applied Mechanics and Materials · doi:10.4028/www.scientific.net/amm.607.65 · Cited by 16
Cited by
Wickramasinghe, S., Do, T., & Tran, P. (2020) · Polymers · doi:10.3390/polym12071529 · Cited by 1,052
Daminabo, S. C., Goel, S., Grammatikos, S. A., Nezhad, H. Y., & Thakur, V. K. (2020) · Materials Today Chemistry · doi:10.1016/j.mtchem.2020.100248 · Cited by 567
Polylactic Acid (PLA) Biocomposite: Processing, Additive Manufacturing and Advanced Applications
Ilyas, R. A., Sapuan, S. M., Harussani, M. M., Hakimi, M. Y. A. Y., Haziq, M. Z. M., Atikah, M. S. N., Asyraf, M. R. M., Ishak, M. R., Razman, M. R., Nurazzi, N. M., et al. (2021) · Polymers · doi:10.3390/polym13081326 · Cited by 513
Fused deposition modeling: process, materials, parameters, properties, and applications
Rajan, K., Samykano, M., Kadirgama, K., Harun, W. S. W., & Rahman, M. M. (2022) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-022-08860-7 · Cited by 426
Ilyas, R., Zuhri, M., Aisyah, H., Asyraf, M., Hassan, S., Zainudin, E., Sapuan, S., Sharma, S., Bangar, S., Jumaidin, R., et al. (2022) · Polymers · doi:10.3390/polym14010202 · Cited by 369
Metadata
- Authors
- Le Duigou, A., Barbé, A., Guillou, E., & Castro, M.
- Venue
- Materials & Design
- Publisher
- Elsevier BV
- Published
- 2019-10
- Volume
- 180
- Pages
- 107884
- ISSN
- 0264-1275 (ISSN-L)
- OpenAlex
- W2947750900
- Cited by
- 309
- References
- 34
- FWCI
- 11.35
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.