CoChat

3D Printing PDMS Elastomer in a Hydrophilic Support Bath via Freeform Reversible Embedding

Open access
Hinton, Thomas J., Hudson, Andrew, Pusch, Kira, Lee, Andrew, Feinberg, Adam W. · 2016 · ACS Biomaterials Science & Engineering

The DOI matches its Crossref record; 16 of the 16 references it cites were found in a registry or an index.

Abstract

Polydimethylsiloxane (PDMS) elastomer is used in a wide range of biomaterial applications including microfluidics, cell culture substrates, flexible electronics, and medical devices. However, it has proved challenging to 3D print PDMS in complex structures due to its low elastic modulus and need for support during the printing process. Here we demonstrate the 3D printing of hydrophobic PDMS prepolymer resins within a hydrophilic Carbopol gel support via freeform reversible embedding (FRE). In the FRE printing process, the Carbopol support acts as a Bingham plastic that yields and fluidizes when the syringe tip of the 3D printer moves through it, but acts as a solid for the PDMS extruded within it. This, in combination with the immiscibility of hydrophobic PDMS in the hydrophilic Carbopol, confines the PDMS prepolymer within the support for curing times up to 72 h while maintaining dimensional stability. After printing and curing, the Carbopol support gel releases the embedded PDMS prints by using phosphate buffered saline solution to reduce the Carbopol yield stress. As proof-of-concept, we used Sylgard 184 PDMS to 3D print linear and helical filaments via continuous extrusion and cylindrical and helical tubes via layer-by-layer fabrication. Importantly, we show that the 3D printed tubes were manifold and perfusable. The results demonstrate that hydrophobic polymers with low viscosity and long cure times can be 3D printed using a hydrophilic support, expanding the range of biomaterials that can be used in additive manufacturing. Further, by implementing the technology using low cost open-source hardware and software tools, the FRE printing technique can be rapidly implemented for research applications.

Overview

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.1021/acsbiomaterials.6b00170

Cites

16 of 16 references verified0 citation errors · 0 not checkable

Statistics

Figures

Image 1
CC-BY · From the PDF
Figure 1 FRE printing is performed by extruding PDMS prepolymer in a support bath consisting of Carbopol gel. (A) A 3D fi le of a vase is imported and processed into G-code before being 3D printed. (B) The 3D fi le is replicated, layer-by-layer, from PDMS embedded within the Carbopol support bath by a syringe-based 3D printer. (top) A schematic of the printing process showing the vase in (A) printed within a 50 mL centrifuge tube fi lled with Carbopol. (bottom) A photograph of the actual vase being 3D printed from PDMS in the Carbopol, due to similar index of refraction it is di ffi cult to see the vase. After printing the PDMS is cured for 72 h at room temperature or 2 h at 65 ° C. (C) Following curing of the embedded PDMS, the Carbopol bath is lique fi ed by addition of monovalent cations, in this case a PBS solution, combined with mechanical agitation. (D) After the support bath is lique fi ed, the print can be removed. Scale bar is 1 cm.
Figure 1 FRE printing is performed by extruding PDMS prepolymer in a support bath consisting of Carbopol gel. (A) A 3D fi le of a vase is imported and processed into G-code before being 3D printed. (B) The 3D fi le is replicated, layer-by-layer, from PDMS embedded within the Carbopol support bath by a syringe-based 3D printer. (top) A schematic of the printing process showing the vase in (A) printed within a 50 mL centrifuge tube fi lled with Carbopol. (bottom) A photograph of the actual vase being 3D printed from PDMS in the Carbopol, due to similar index of refraction it is di ffi cult to see the vase. After printing the PDMS is cured for 72 h at room temperature or 2 h at 65 ° C. (C) Following curing of the embedded PDMS, the Carbopol bath is lique fi ed by addition of monovalent cations, in this case a PBS solution, combined with mechanical agitation. (D) After the support bath is lique fi ed, the print can be removed. Scale bar is 1 cm.CC-BY · From the PDF
Figure 2 PDMS prepolymer fi laments extruder and cured at di ff erent temperatures and in di ff erent Carbopols are dimensionally stable. (A) Representative phase-contrast images of PDMS fi laments extruded into Carbopol 940, ETD 2020 and Ultrez 30 and cured at 65 ° C for 2 h or 20 ° C for 72 h showed small morphological di ff erences due to the type of Carbopol, but not due to cure temperature (scale bar is 200 μ m). (B) Quanti fi cation of PDMS fi lament diameter for target extrusion diameters of 140, 280, and 400 μ m (green lines) showed the ability to generally achieve diameters within 10%. The cure temperatures of 65 ° C for 2 h (red) and 20 ° C for 72 h (blue) did not have a statistically signi fi cant e ff ect on diameter (as determined by t tests between cure temperatures for each target diameter and Carbopol type, P < 0.05). (C) Surface and cross-sectional renderings of PDMS fi laments imaged using laser scanning confocal microscopy veri fi ed the smooth surface and circular cross-section of PDMS extruded in Carbopol 940 ETD 2020 and the rough surface of PDMS extruded in Ultrez 30 (units in 3D rendering are in micrometers, scale bar is 100 μ m).
Figure 2 PDMS prepolymer fi laments extruder and cured at di ff erent temperatures and in di ff erent Carbopols are dimensionally stable. (A) Representative phase-contrast images of PDMS fi laments extruded into Carbopol 940, ETD 2020 and Ultrez 30 and cured at 65 ° C for 2 h or 20 ° C for 72 h showed small morphological di ff erences due to the type of Carbopol, but not due to cure temperature (scale bar is 200 μ m). (B) Quanti fi cation of PDMS fi lament diameter for target extrusion diameters of 140, 280, and 400 μ m (green lines) showed the ability to generally achieve diameters within 10%. The cure temperatures of 65 ° C for 2 h (red) and 20 ° C for 72 h (blue) did not have a statistically signi fi cant e ff ect on diameter (as determined by t tests between cure temperatures for each target diameter and Carbopol type, P < 0.05). (C) Surface and cross-sectional renderings of PDMS fi laments imaged using laser scanning confocal microscopy veri fi ed the smooth surface and circular cross-section of PDMS extruded in Carbopol 940 ETD 2020 and the rough surface of PDMS extruded in Ultrez 30 (units in 3D rendering are in micrometers, scale bar is 100 μ m).CC-BY · From the PDF
Figure 3 Release of cured PDMS prints by using NaCl solution to decrease yield stress and viscosity. (A) Rheometry of Carbopol gels diluted in water and in PBS bu ff er demonstrated a thinning behavior in the presence of ionic bu ff er solutions, whereby they transition from a yield-stress fl uid to a shear-thinning fl uid. (B) An example of a FRE printed PDMS cylinder (dyed black) in the Carbopol support submerged in a larger beaker consisting of PBS and a magnetically driven stir bar for mechanical agitation. (C) A time-lapse showing the print being released from the Carbopol support by taking advantage of this thinning behavior. Apparent image blurriness is an e ff ect of the Carbopol suspension.
Figure 3 Release of cured PDMS prints by using NaCl solution to decrease yield stress and viscosity. (A) Rheometry of Carbopol gels diluted in water and in PBS bu ff er demonstrated a thinning behavior in the presence of ionic bu ff er solutions, whereby they transition from a yield-stress fl uid to a shear-thinning fl uid. (B) An example of a FRE printed PDMS cylinder (dyed black) in the Carbopol support submerged in a larger beaker consisting of PBS and a magnetically driven stir bar for mechanical agitation. (C) A time-lapse showing the print being released from the Carbopol support by taking advantage of this thinning behavior. Apparent image blurriness is an e ff ect of the Carbopol suspension.CC-BY · From the PDF
Figure 4 Representative FRE printed PDMS structures using the Carbopol support. (A) The Carbopol gel is capable of supporting freeform extrusion such as this helical path rendered in G-code. (B) The helical extrusion appears identical to the G-code when embedded in the Carbopol (dyed black for visualization). (C) After curing and release, the PDMS helix print retains its geometry when fl oating in water. (D) G-code for a cylindrical tube created using a helical extrusion. (E) The layers of PDMS fi laments fuse into a monolithic surface. (F) After curing and release, the printed tube remains fused between layers and is sti ff enough to maintain its geometry while being handled. (G) The G-code for more complex helical tube. (H) As with the tube, the layers of the helical tube are supported within the Carbopol. (I) Release of the helical tube from the Carbopol gel shows the maintenance of geometrical features, supported in water because it cannot support its own weight, even when cured. (J) A PDMS tube to demonstrate the manifold nature of the print ' s outer surfaces (scale bar is 4 mm). (K) A time-lapse heat map of dye perfused through the tube (scale bar is 4 mm.) (L) G-code of a bifurcation with a webbed fork for stability. (M) The FRE printed PDMS bifurcation embedded in the Carbopol. (N) Perfusion of dye through the bifurcation, splitting fl uid fl ow.
Figure 4 Representative FRE printed PDMS structures using the Carbopol support. (A) The Carbopol gel is capable of supporting freeform extrusion such as this helical path rendered in G-code. (B) The helical extrusion appears identical to the G-code when embedded in the Carbopol (dyed black for visualization). (C) After curing and release, the PDMS helix print retains its geometry when fl oating in water. (D) G-code for a cylindrical tube created using a helical extrusion. (E) The layers of PDMS fi laments fuse into a monolithic surface. (F) After curing and release, the printed tube remains fused between layers and is sti ff enough to maintain its geometry while being handled. (G) The G-code for more complex helical tube. (H) As with the tube, the layers of the helical tube are supported within the Carbopol. (I) Release of the helical tube from the Carbopol gel shows the maintenance of geometrical features, supported in water because it cannot support its own weight, even when cured. (J) A PDMS tube to demonstrate the manifold nature of the print ' s outer surfaces (scale bar is 4 mm). (K) A time-lapse heat map of dye perfused through the tube (scale bar is 4 mm.) (L) G-code of a bifurcation with a webbed fork for stability. (M) The FRE printed PDMS bifurcation embedded in the Carbopol. (N) Perfusion of dye through the bifurcation, splitting fl uid fl ow.CC-BY · From the PDF

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Claims other papers make about this one

Each is checked against this paper’s own text: does it say what the citing paper says it does?

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cites

Show all 16 references

Research works printed but not linked: 3

  1. Ratner, 2013, Biomaterials Science: An Introduction to Materials in Medicine, 1573
  2. Lipton, J. I.; Angle, S.; Lipson, H. 3D Printable Wax-Silicone Actuators. In 2014 Annual International Solid Freeform Fabrication Symposium;Austin, TX, Aug 4–6, 2014; Laboratory for Freeform Fabrication and University of Texas: Austin, TX, 2014; pp 848–56.
  3. 2010, Technical Data Sheet 730: Viscosity of Carbopol* Polymers in Aqueous Systems, 1

Cited by

See all 481

Metadata

Authors
Hinton, T. J., Hudson, A., Pusch, K., Lee, A., & Feinberg, A. W.
Affiliations
Carnegie Mellon University (US)
Corresponding author
Feinberg, Adam W.
Venue
ACS Biomaterials Science & Engineering
Published
2016-05-04
Volume
2
Issue
10
Pages
1781-1786
ISSN
2373-9878 (ISSN-L)
OpenAlex
W2345451752
Cited by
437
References
16
Citations by year
2026: 22 · 2025: 32 · 2024: 44 · 2023: 46 · 2022: 50 · 2021: 68 · 2020: 63 · 2019: 46 · 2018: 41 · 2017: 24 · 2016: 1
FWCI
17.97
Type
journal article
Language
en
Open access
Locations
  • ACS Biomaterials Science & Engineering (publishedVersion, cc-by)
  • Europe PMC (PubMed Central) (publishedVersion)
  • PubMed Central (publishedVersion)
  • PubMed (publishedVersion)
Funders
  • U.S. Department of Health and Human Services (DP2HL117750)
  • National Science Foundation (1454248)
  • Disruptive Health Technology Institute, Carnegie Mellon University (A017261-HIGHMARK-Feinberg)
Topics
  • Physical Sciences › Engineering › Biomedical Engineering › 3D Printing in Biomedical Research
  • Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Additive Manufacturing and 3D Printing Technologies
  • Physical Sciences › Engineering › Biomedical Engineering › Microfluidic and Capillary Electrophoresis Applications
Keywords
support removal, phosphate buffered saline, helical filaments, microfluidics

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: 3D Printing PDMS Elastomer in a Hydrophilic Support Bath via Freeform Reversible Embedding. https://app.cochat.ai/papers/10.1021/acsbiomaterials.6b00170
The paper
Hinton, T. J., Hudson, A., Pusch, K., Lee, A., & Feinberg, A. W. (2016). 3D Printing PDMS Elastomer in a Hydrophilic Support Bath via Freeform Reversible Embedding. ACS Biomaterials Science & Engineering. https://doi.org/10.1021/acsbiomaterials.6b00170

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.