3D Printing PDMS Elastomer in a Hydrophilic Support Bath via Freeform Reversible Embedding
Open accessThe DOI matches its Crossref record; 16 of the 16 references it cites were found in a registry or an index.
Abstract
Polydimethylsiloxane (PDMS) elastomer is used in a wide range of biomaterial applications including microfluidics, cell culture substrates, flexible electronics, and medical devices. However, it has proved challenging to 3D print PDMS in complex structures due to its low elastic modulus and need for support during the printing process. Here we demonstrate the 3D printing of hydrophobic PDMS prepolymer resins within a hydrophilic Carbopol gel support via freeform reversible embedding (FRE). In the FRE printing process, the Carbopol support acts as a Bingham plastic that yields and fluidizes when the syringe tip of the 3D printer moves through it, but acts as a solid for the PDMS extruded within it. This, in combination with the immiscibility of hydrophobic PDMS in the hydrophilic Carbopol, confines the PDMS prepolymer within the support for curing times up to 72 h while maintaining dimensional stability. After printing and curing, the Carbopol support gel releases the embedded PDMS prints by using phosphate buffered saline solution to reduce the Carbopol yield stress. As proof-of-concept, we used Sylgard 184 PDMS to 3D print linear and helical filaments via continuous extrusion and cylindrical and helical tubes via layer-by-layer fabrication. Importantly, we show that the 3D printed tubes were manifold and perfusable. The results demonstrate that hydrophobic polymers with low viscosity and long cure times can be 3D printed using a hydrophilic support, expanding the range of biomaterials that can be used in additive manufacturing. Further, by implementing the technology using low cost open-source hardware and software tools, the FRE printing technique can be rapidly implemented for research applications.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Figures





Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“Models that replicate the geometrically complex structure of the heart, harboring chambers and large vessels with soft biomaterials, can be achieved using 3D bioprinting.”
From In situ expansion, differentiation, and electromechanical coupling of human cardiac muscle in a 3D bioprinted, chambered organoid (2020) · cites this paper as [12]
Experimental — accuracy not yet measuredThe source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“The concept is gaining traction, as the ability to print tissues composed entirely of native proteins, cells and/or biocompatible synthetic components is possible and accessible to many laboratories9–17.”
From In situ expansion, differentiation, and electromechanical coupling of human cardiac muscle in a 3D bioprinted, chambered organoid (2020) · cites this paper as [12]
Experimental — accuracy not yet measuredThe cited source says what the claim attributes to it.
In the citing paper
“Ultimately, we employed freeform reversible embedding of suspended hydrogels9, 12 with success, wherein our embedding material or “slurry” consisted of gelatin microparticles.”
From In situ expansion, differentiation, and electromechanical coupling of human cardiac muscle in a 3D bioprinted, chambered organoid (2020) · cites this paper as [12]
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Poly(dimethylsiloxane) as a Material for Fabricating Microfluidic Devices
McDonald, J. C., & Whitesides, G. M. (2002) · Accounts of Chemical Research · doi:10.1021/ar010110q · Cited by 2,454
3D bioprinting of vascularized, heterogeneous cell-laden tissue constructs
Kolesky, D. B., Truby, R. L., Gladman, A. S., Busbee, T. A., Homan, K. A., & Lewis, J. A. (2014) · Advanced Materials · doi:10.1002/adma.201305506 · Cited by 2,102
Hinton, T. J., Jallerat, Q., Palchesko, R. N., Park, J. H., Grodzicki, M. S., Shue, H.-J., Ramadan, M. H., Hudson, A. R., & Feinberg, A. W. (2015) · Science Advances · doi:10.1126/sciadv.1500758 · Cited by 1,805
Self-citationThree-dimensional bioprinting of thick vascularized tissues
Kolesky, D. B., Homan, K. A., Skylar-Scott, M. A., & Lewis, J. A. (2016) · Proceedings of the National Academy of Sciences · doi:10.1073/pnas.1521342113 · Cited by 1,492
Mannoor, M. S., Jiang, Z., James, T., Kong, Y. L., Malatesta, K. A., Soboyejo, W. O., Verma, N., Gracias, D. H., & McAlpine, M. C. (2013) · Nano Letters · doi:10.1021/nl4007744 · Cited by 874
Flexible and Stretchable Electronics for Biointegrated Devices
Kim, D.-H., Ghaffari, R., Lu, N., & Rogers, J. A. (2012) · Annual Review of Biomedical Engineering · doi:10.1146/annurev-bioeng-071811-150018 · Cited by 749
Writing in the granular gel medium
Bhattacharjee, T., Zehnder, S. M., Rowe, K. G., Jain, S., Nixon, R. M., Sawyer, W. G., & Angelini, T. E. (2015) · Science Advances · doi:10.1126/sciadv.1500655 · Cited by 635
Integrated 3D-printed reactionware for chemical synthesis and analysis
Symes, M. D., Kitson, P. J., Yan, J., Richmond, C. J., Cooper, G. J. T., Bowman, R. W., Vilbrandt, T., & Cronin, L. (2012) · Nature Chemistry · doi:10.1038/nchem.1313 · Cited by 617
Palchesko, R. N., Zhang, L., Sun, Y., & Feinberg, A. W. (2012) · PLoS ONE · doi:10.1371/journal.pone.0051499 · Cited by 559
Self-citationBélanger, M., & Marois, Y. (2001) · Journal of Biomedical Materials Research · doi:10.1002/jbm.1043 · Cited by 471
Research works printed but not linked: 3
- Ratner, 2013, Biomaterials Science: An Introduction to Materials in Medicine, 1573
- Lipton, J. I.; Angle, S.; Lipson, H. 3D Printable Wax-Silicone Actuators. In 2014 Annual International Solid Freeform Fabrication Symposium;Austin, TX, Aug 4–6, 2014; Laboratory for Freeform Fabrication and University of Texas: Austin, TX, 2014; pp 848–56.
- 2010, Technical Data Sheet 730: Viscosity of Carbopol* Polymers in Aqueous Systems, 1
Cited by
Direct Ink Writing: A 3D Printing Technology for Diverse Materials
Saadi, M. A. S. R., Maguire, A., Pottackal, N. T., Thakur, M. S. H., Ikram, M. M., Hart, A. J., Ajayan, P. M., & Rahman, M. M. (2022) · Advanced Materials · doi:10.1002/adma.202108855 · Cited by 1,335
3D printing of soft robotic systems
Wallin, T. J., Pikul, J., & Shepherd, R. F. (2018) · Nature Reviews Materials · doi:10.1038/s41578-018-0002-2 · Cited by 942
A Review of 3D Printing Technologies for Soft Polymer Materials
Zhou, L., Fu, J., & He, Y. (2020) · Advanced Functional Materials · doi:10.1002/adfm.202000187 · Cited by 713
Highly Stretchable and UV Curable Elastomers for Digital Light Processing Based 3D Printing
Patel, D. K., Sakhaei, A. H., Layani, M., Zhang, B., Ge, Q., & Magdassi, S. (2017) · Advanced Materials · doi:10.1002/adma.201606000 · Cited by 673
Support Structures for Additive Manufacturing: A Review
Jiang, J., Xu, X., & Stringer, J. (2018) · Journal of Manufacturing and Materials Processing · doi:10.3390/jmmp2040064 · Cited by 527
“[76] demonstrated a new method of 3D printing polydimethylsiloxane (PDMS) using a hydrophilic Carbopol support bath.”
MethodJammed Microgel Inks for 3D Printing Applications
Highley, C. B., Song, K. H., Daly, A. C., & Burdick, J. A. (2019) · Advanced Science · doi:10.1002/advs.201801076 · Cited by 456
3D Printing of Transparent and Conductive Heterogeneous Hydrogel–Elastomer Systems
Tian, K., Bae, J., Bakarich, S. E., Yang, C., Gately, R. D., Spinks, G. M., in het Panhuis, M., Suo, Z., & Vlassak, J. J. (2017) · Advanced Materials · doi:10.1002/adma.201604827 · Cited by 419
Multimaterial actinic spatial control 3D and 4D printing
Schwartz, J. J., & Boydston, A. J. (2019) · Nature Communications · doi:10.1038/s41467-019-08639-7 · Cited by 343
Kupfer, M. E., Lin, W.-H., Ravikumar, V., Qiu, K., Wang, L., Gao, L., Bhuiyan, D. B., Lenz, M., Ai, J., Mahutga, R. R., et al. (2020) · Circulation Research · doi:10.1161/circresaha.119.316155 · Cited by 329
Polymer Design for 3D Printing Elastomers: Recent Advances in Structure, Properties, and Printing
Herzberger, J., Sirrine, J. M., Williams, C. B., & Long, T. E. (2019) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2019.101144 · Cited by 329
Bhattacharjee, N., Parra‐Cabrera, C., Kim, Y. T., Kuo, A. P., & Folch, A. (2018) · Advanced Materials · doi:10.1002/adma.201800001 · Cited by 322
Current Biomedical Applications of 3D Printing and Additive Manufacturing
Ahangar, P., Cooke, M. E., Weber, M. H., & Rosenzweig, D. H. (2019) · Applied Sciences · doi:10.3390/app9081713 · Cited by 309
FRESH 3D Bioprinting a Full-Size Model of the Human Heart
Mirdamadi, E., Tashman, J. W., Shiwarski, D. J., Palchesko, R. N., & Feinberg, A. W. (2020) · ACS Biomaterials Science & Engineering · doi:10.1021/acsbiomaterials.0c01133 · Cited by 292
Self-citationRecent progress in fabrication and application of polydimethylsiloxane sponges
Zhu, D., Handschuh-Wang, S., & Zhou, X. (2017) · Journal of Materials Chemistry A · doi:10.1039/c7ta04577h · Cited by 278
Zare, M., Ghomi, E. R., Venkatraman, P. D., & Ramakrishna, S. (2021) · Journal of Applied Polymer Science · doi:10.1002/app.50969 · Cited by 278
Self-assembled micro-organogels for 3D printing silicone structures
O’Bryan, C. S., Bhattacharjee, T., Hart, S., Kabb, C. P., Schulze, K. D., Chilakala, I., Sumerlin, B. S., Sawyer, W. G., & Angelini, T. E. (2017) · Science Advances · doi:10.1126/sciadv.1602800 · Cited by 277
“Interfacial interactions between silicone inks and aqueous support materials limit printing precision and inhibit adhesion between printed features (13); commercially available siliconebased microgels practically offer no rheological control of the support medium (12).”
BackgroundAdvances in 3D/4D printing of mechanical metamaterials: From manufacturing to applications
Zhou, X., Ren, L., Song, Z., Li, G., Zhang, J., Li, B., Wu, Q., Li, W., Ren, L., & Liu, Q. (2023) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2023.110585 · Cited by 277
3D-printed silica with nanoscale resolution
Wen, X., Zhang, B., Wang, W., Ye, F., Yue, S., Guo, H., Gao, G., Zhao, Y., Fang, Q., Nguyen, C., et al. (2021) · Nature Materials · doi:10.1038/s41563-021-01111-2 · Cited by 259
Polymeric Systems for Bioprinting
Bedell, M. L., Navara, A. M., Du, Y., Zhang, S., & Mikos, A. G. (2020) · Chemical Reviews · doi:10.1021/acs.chemrev.9b00834 · Cited by 258
Functional Polymers and Nanocomposites for 3D Printing of Smart Structures and Devices
Nadgorny, M., & Ameli, A. (2018) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.8b01786 · Cited by 244
Viscoplastic Matrix Materials for Embedded 3D Printing
Grosskopf, A. K., Truby, R. L., Kim, H., Perazzo, A., Lewis, J. A., & Stone, H. A. (2018) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.7b19818 · Cited by 243
Functional PDMS Elastomers: Bulk Composites, Surface Engineering, and Precision Fabrication
Li, S., Zhang, J., He, J., Liu, W., Wang, Y., Huang, Z., Pang, H., & Chen, Y. (2023) · Advanced Science · doi:10.1002/advs.202304506 · Cited by 238
Montazerian, H., Mohamed, M. G. A., Montazeri, M. M., Kheiri, S., Milani, A. S., Kim, K., & Hoorfar, M. (2019) · Acta Biomaterialia · doi:10.1016/j.actbio.2019.06.040 · Cited by 232
3D-Printed Ultra-Robust Surface-Doped Porous Silicone Sensors for Wearable Biomonitoring
Davoodi, E., Montazerian, H., Haghniaz, R., Rashidi, A., Ahadian, S., Sheikhi, A., Chen, J., Khademhosseini, A., Milani, A. S., Hoorfar, M., et al. (2020) · ACS Nano · doi:10.1021/acsnano.9b06283 · Cited by 232
Rheology and printability: A survey of critical relationships for direct ink write materials design
Rau, D. A., Williams, C. B., & Bortner, M. J. (2023) · Progress in Materials Science · doi:10.1016/j.pmatsci.2023.101188 · Cited by 227
Jeon, O., Lee, Y. B., Jeong, H., Lee, S. J., Wells, D., & Alsberg, E. (2019) · Materials Horizons · doi:10.1039/c9mh00375d · Cited by 221
Emergence of FRESH 3D printing as a platform for advanced tissue biofabrication
Shiwarski, D. J., Hudson, A. R., Tashman, J. W., & Feinberg, A. W. (2021) · APL Bioengineering · doi:10.1063/5.0032777 · Cited by 216
Self-citationEvaluation of bioink printability for bioprinting applications
Zhang, Z., Jin, Y., Yin, J., Xu, C., Xiong, R., Christensen, K., Ringeisen, B. R., Chrisey, D. B., & Huang, Y. (2018) · Applied Physics Reviews · doi:10.1063/1.5053979 · Cited by 214
3D bioprinting and its innovative approach for biomedical applications
Tripathi, S., Mandal, S. S., Bauri, S., & Maiti, P. (2023) · MedComm · doi:10.1002/mco2.194 · Cited by 206
Malekpour, A., & Chen, X. (2022) · Journal of Functional Biomaterials · doi:10.3390/jfb13020040 · Cited by 206
“This approach reduces irregularity and exhibits a smooth surface for the filaments [92,93].”
BackgroundLee, K. W., Lim, W., Jeon, M. S., Jang, H., Hwang, J., Lee, C. H., & Kim, D. R. (2022) · Advanced Functional Materials · doi:10.1002/adfm.202105882 · Cited by 200
Budharaju, H., Sundaramurthi, D., & Sethuraman, S. (2023) · Bioactive Materials · doi:10.1016/j.bioactmat.2023.10.012 · Cited by 201
“However, this method has some limitations, such as lateral fusion of extruded PDMS filaments, and it required pressurized conditions to hold the constructs in defined shapes [67].”
MethodInfluentialBioprinting 101: Design, Fabrication, and Evaluation of Cell-Laden 3D Bioprinted Scaffolds
Deo, K. A., Singh, K. A., Peak, C. W., Alge, D. L., & Gaharwar, A. K. (2020) · Tissue Engineering Part A · doi:10.1089/ten.tea.2019.0298 · Cited by 199
“…94,145 alginate, 50,146 and PEG 147,148 along with materials such as, peptides, 149–151 polycaprolactone, 152–154 kappa-carrageenan, 57,155 and others 156–158 have been extensively explored to comprehend the interplay between printing parameters and cellular response to the bioprinting process.”
Jung, S., Kara, L. B., Nie, Z., Simpson, T. W., & Whitefoot, K. S. (2023) · Environmental Science & Technology · doi:10.1021/acs.est.2c04927 · Cited by 190
“96,97 AM Processes That Do Not Require Support Structures.”
3D Printing by Multiphase Silicone/Water Capillary Inks
Roh, S., Parekh, D. P., Bharti, B., Stoyanov, S. D., & Velev, O. D. (2017) · Advanced Materials · doi:10.1002/adma.201701554 · Cited by 187
3D bioprinting in cardiac tissue engineering
Wang, Z., Wang, L., Li, T., Liu, S., Guo, B., Huang, W., & Wu, Y. (2021) · Theranostics · doi:10.7150/thno.61621 · Cited by 185
“[89] printed helical and tubular structures in a Carbopol support gel (Figure 5D).”
BackgroundHigh‐Resolution 3D Printing for Electronics
Park, Y., Yun, I., Chung, W. G., Park, W., Lee, D. H., & Park, J. (2022) · Advanced Science · doi:10.1002/advs.202104623 · Cited by 184
Additive manufacturing of silicone structures: A review and prospective
Liravi, F., & Toyserkani, E. (2018) · Additive manufacturing · doi:10.1016/j.addma.2018.10.002 · Cited by 181
3D Printing of PDMS Improves Its Mechanical and Cell Adhesion Properties
Ozbolat, V., Dey, M., Ayan, B., Povilianskas, A., Demirel, M. C., & Ozbolat, I. T. (2018) · ACS Biomaterials Science & Engineering · doi:10.1021/acsbiomaterials.7b00646 · Cited by 173
Shi, G., Lowe, S. E., Teo, A. J. T., Dinh, T. K., Tan, S. H., Qin, J., Zhang, Y., Zhong, Y. L., & Zhao, H. (2019) · Applied Materials Today · doi:10.1016/j.apmt.2019.06.016 · Cited by 170
Pneumatic Soft Robots: Challenges and Benefits
Su, H., Hou, X., Zhang, X., Qi, W., Cai, S., Xiong, X., & Guo, J. (2022) · Actuators · doi:10.3390/act11030092 · Cited by 170
“3D printing can create molds of complex structures, allowing soft robots [30] to be produced with complex structures [31,32].”
Photoreversible Covalent Hydrogels for Soft-Matter Additive Manufacturing
Kabb, C. P., O’Bryan, C. S., Deng, C. C., Angelini, T. E., & Sumerlin, B. S. (2018) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.8b02441 · Cited by 167
Essential steps in bioprinting: From pre- to post-bioprinting
Datta, P., Barui, A., Wu, Y., Ozbolat, V., Moncal, K. K., & Ozbolat, I. T. (2018) · Biotechnology Advances · doi:10.1016/j.biotechadv.2018.06.003 · Cited by 165
Intelligent Soft Surgical Robots for Next‐Generation Minimally Invasive Surgery
Zhu, J., Lyu, L., Xu, Y., Liang, H., Zhang, X., Ding, H., & Wu, Z. (2021) · Advanced Intelligent Systems · doi:10.1002/aisy.202100011 · Cited by 165
Jin, Y., Chai, W., & Huang, Y. (2017) · Materials Science and Engineering: C · doi:10.1016/j.msec.2017.05.144 · Cited by 158
Liu, Z., Hong, P., Huang, Z., Zhang, T., Xu, R., Chen, L., Xiang, H., & Liu, X. (2020) · Chemical Engineering Journal · doi:10.1016/j.cej.2020.124142 · Cited by 158
Processing and Properties of Chitosan Inks for 3D Printing of Hydrogel Microstructures
Wu, Q., Therriault, D., & Heuzey, M. (2018) · ACS Biomaterials Science & Engineering · doi:10.1021/acsbiomaterials.8b00415 · Cited by 156
Three-dimensional printing with sacrificial materials for soft matter manufacturing
O’Bryan, C. S., Bhattacharjee, T., Niemi, S. R., Balachandar, S., Baldwin, N., Ellison, S. T., Taylor, C. R., Sawyer, W. G., & Angelini, T. E. (2017) · MRS Bulletin · doi:10.1557/mrs.2017.167 · Cited by 156
Synthetic Polymers for Organ 3D Printing
Liu, F., & Wang, X. (2020) · Polymers · doi:10.3390/polym12081765 · Cited by 155
“The Carbopol acts as a Bingham plastic that yields and fluidizes when the syringe tip of the 3D printer moves through it and solidifies the PDMS extruded within it (Figure 12) [156].”
BackgroundFunctional Nanoclay Suspension for Printing-Then-Solidification of Liquid Materials
Jin, Y., Compaan, A. M., Chai, W., & Huang, Y. H. (2017) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.7b02398 · Cited by 153
Gellan Fluid Gel as a Versatile Support Bath Material for Fluid Extrusion Bioprinting
Compaan, A. M., Song, K., & Huang, Y. (2019) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.8b13792 · Cited by 133
Cardiac tissue engineering: state-of-the-art methods and outlook
Nguyen, A. H., Marsh, P., Schmiess-Heine, L., Burke, P. J., Lee, A., Lee, J., & Cao, H. (2019) · Journal of Biological Engineering · doi:10.1186/s13036-019-0185-0 · Cited by 139
Self-citation3D printable tough silicone double networks
Wallin, T. J., Simonsen, L., Pan, W., Wang, K., Giannelis, E. P., Shepherd, R. F., & Mengüç, Y. (2020) · Nature Communications · doi:10.1038/s41467-020-17816-y · Cited by 148
Bioprinted chitosan-gelatin thermosensitive hydrogels using an inexpensive 3D printer
Roehm, K. D., & Madihally, S. V. (2017) · Biofabrication · doi:10.1088/1758-5090/aa96dd · Cited by 131
“could consider using high density bath [55] or pre-warmed media, which could provide uniform”
BackgroundFabrication of Complex Hydrogel Structures Using Suspended Layer Additive Manufacturing (SLAM)
Senior, J. J., Cooke, M. E., Grover, L. M., & Smith, A. M. (2019) · Advanced Functional Materials · doi:10.1002/adfm.201904845 · Cited by 141
Stiff and tough PDMS-MMT layered nanocomposites visualized by AIE luminogens
Peng, J., Tomsia, A. P., Jiang, L., Tang, B. Z., & Cheng, Q. (2021) · Nature Communications · doi:10.1038/s41467-021-24835-w · Cited by 140
Classification, processing, and applications of bioink and 3D bioprinting: A detailed review
Raees, S., Ullah, F., Javed, F. T., Akil, H. M., Khan, M. J., Safdar, M. M., Din, I. U., Alotaibi, M. A., Alharthi, A. I., Bakht, M. A., et al. (2023) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2023.123476 · Cited by 141
Biomaterials for Bioprinting Microvasculature
Barrs, R. W., Jia, J., Silver, S. E., Yost, M. J., & Mei, Y. (2020) · Chemical Reviews · doi:10.1021/acs.chemrev.0c00027 · Cited by 140
3D printing of glass by additive manufacturing techniques: a review
Zhang, D., Liu, X., & Qiu, J. (2020) · Frontiers of Optoelectronics · doi:10.1007/s12200-020-1009-z · Cited by 138
Polydimethylsiloxane Composites for Optical Ultrasound Generation and Multimodality Imaging
Noimark, S., Colchester, R. J., Poduval, R. K., Maneas, E., Alles, E. J., Zhao, T., Zhang, E., Ashworth, M. T., Tsolaki, E., Chester, A. H., et al. (2018) · Advanced Functional Materials · doi:10.1002/adfm.201704919 · Cited by 137
Afghah, F., Altunbek, M., Dikyol, C., & Koç, B. (2020) · Scientific Reports · doi:10.1038/s41598-020-61606-x · Cited by 137
Suspension 3D Printing of Liquid Metal into Self‐Healing Hydrogel
Yu, Y., Liu, F., Zhang, R., & Liu, J. (2017) · Advanced Materials Technologies · doi:10.1002/admt.201700173 · Cited by 136
Printing Reconfigurable Bundles of Dielectric Elastomer Fibers
Chortos, A., Mao, J., Mueller, J., Hajiesmaili, E., Lewis, J. A., & Clarke, D. R. (2021) · Advanced Functional Materials · doi:10.1002/adfm.202010643 · Cited by 136
Carve, M., & Włodkowic, D. (2018) · Micromachines · doi:10.3390/mi9020091 · Cited by 134
“To mitigate the toxicity of unreacted PEG-DA monomers and PI, the surfaces were subjected to an additional curing step in a UV bath to allow residual compounds to leach.”
BackgroundMethodInfluentialAspiration-assisted freeform bioprinting of pre-fabricated tissue spheroids in a yield-stress gel
Ayan, B., Celik, N., Zhang, Z., Zhou, K., Kim, M. H., Banerjee, D., Wu, Y. B., Costanzo, F., & Ozbolat, I. T. (2020) · Communications Physics · doi:10.1038/s42005-020-00449-4 · Cited by 134
“Although extrusion-based bioprinting in yield-stress gels has already been demonstrated in the literature 5,6,10,14,17,19,38 , its utilization in bioprinting of prefabricated cellular aggregates is quite challenging.”
Tony, A., Badea, I., Yang, C., Liu, Y., Wells, G., Wang, K., Yin, R., Zhang, H., & Zhang, W. (2023) · Polymers · doi:10.3390/polym15081926 · Cited by 131
“For instance, PDMS, which is hydrophobic in nature, is printed into a carbopol gel bath, which is hydrophilic, providing the support and dimensional stability during printing [111].”
Background3D Cell Printed Tissue Analogues: A New Platform for Theranostics
Choi, Y.-J., Yi, H.-G., Kim, S.-W., & Cho, D.-W. (2017) · Theranostics · doi:10.7150/thno.19396 · Cited by 121
“Similarly, the printing of a soft material with a complex design was also achieved by embedding polydimethylsiloxane (PDMS) elastomer into a hydrophilic support bath composed of Carbopol® [45].”
MethodNarupai, B., & Nelson, A. (2020) · ACS Macro Letters · doi:10.1021/acsmacrolett.0c00200 · Cited by 121
Ding, H., & Chang, R. C. (2018) · Applied Sciences · doi:10.3390/app8030403 · Cited by 119
A silicone-based support material eliminates interfacial instabilities in 3D silicone printing
Duraivel, S., Laurent, D., Rajon, D. A., Scheutz, G. M., Shetty, A. M., Sumerlin, B. S., Banks, S. A., Bova, F. J., & Angelini, T. E. (2023) · Science · doi:10.1126/science.ade4441 · Cited by 118
3D biofabrication for tubular tissue engineering
Holland, I., Logan, J., Shi, J., McCormick, C., Liu, D., & Shu, W. (2018) · Bio-Design and Manufacturing · doi:10.1007/s42242-018-0013-2 · Cited by 117
Optimization of Silicone 3D Printing with Hierarchical Machine Learning
Menon, A. K., Póczos, B., Feinberg, A. W., & Washburn, N. R. (2019) · 3D Printing and Additive Manufacturing · doi:10.1089/3dp.2018.0088 · Cited by 118
Self-citationLi, T., Hou, J., Wang, L., Zeng, G., Wang, Z., Yu, L., Yang, Q., Yin, J., Long, M., Chen, L., et al. (2022) · Acta Biomaterialia · doi:10.1016/j.actbio.2022.08.037 · Cited by 117
Mahshid, R., Isfahani, M. N., Heidari‐Rarani, M., & Mirkhalaf, M. (2023) · Composites Part A Applied Science and Manufacturing · doi:10.1016/j.compositesa.2023.107584 · Cited by 116
Recent Strategies in Extrusion-Based Three-Dimensional Cell Printing toward Organ Biofabrication
Gao, G., Kim, B. S., Jang, J., & Cho, D. (2019) · ACS Biomaterials Science & Engineering · doi:10.1021/acsbiomaterials.8b00691 · Cited by 115
Liravi, F., & Toyserkani, E. (2017) · Materials & Design · doi:10.1016/j.matdes.2017.10.051 · Cited by 114
Jung, Y., Lee, W., Jung, K., Park, B., Park, J., Ko, J., & Cho, H. (2020) · Polymers · doi:10.3390/polym12061412 · Cited by 110
“Various methods of fabricating polymer-based porous structures such as 3-D printing [28,29], gas foaming [30], phase separation [31,32], and the templating process [33–36] have been introduced over the last 10 years.”
Method3D printed ultra-fast photothermal responsive shape memory hydrogel for microrobots
Zhan, Z., Chen, L., Duan, H., Chen, Y., He, M., & Wang, Z. (2021) · International Journal of Extreme Manufacturing · doi:10.1088/2631-7990/ac376b · Cited by 108
Habibi, M., Foroughi, S., Karamzadeh, V., & Packirisamy, M. (2022) · Nature Communications · doi:10.1038/s41467-022-29395-1 · Cited by 107
Embedded extrusion printing in yield-stress-fluid baths
Wu, Q. H., Song, K., Zhang, D., Ren, B., Sole‐Gras, M., Huang, Y. H., & Yin, J. (2022) · Matter · doi:10.1016/j.matt.2022.09.003 · Cited by 107
Printing bone in a gel: using nanocomposite bioink to print functionalised bone scaffolds
Cidonio, G., Cooke, M. E., Glinka, M., Dawson, J. I., Grover, L. M., & Oreffo, R. O. C. (2019) · Materials Today Bio · doi:10.1016/j.mtbio.2019.100028 · Cited by 106
“[10] demonstrated that the extrusion of the hydrophobic polydimethylsiloxane in a”
Background3D Printing Ionogel Auxetic Frameworks for Stretchable Sensors
Wong, J., Gong, A. T., Defnet, P. A., Meabe, L., Beauchamp, B., Sweet, R. M., Sardón, H., Cobb, C. L., & Nelson, A. (2019) · Advanced Materials Technologies · doi:10.1002/admt.201900452 · Cited by 105
Zheng, R., Chen, Y., Chi, H., Qiu, H., Xue, H., & Bai, H. (2020) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.0c18201 · Cited by 104
Adaptive Self‐Sealing Suction‐Based Soft Robotic Gripper
Song, S., Drotlef, D., Son, D., Koivikko, A., & Sitti, M. (2021) · Advanced Science · doi:10.1002/advs.202100641 · Cited by 104
“and arms, using conventional additive manufacturing techniques (43-46).”
MethodA mini-review of embedded 3D printing: supporting media and strategies
Zhao, J., & He, N. (2020) · Journal of Materials Chemistry B · doi:10.1039/d0tb01819h · Cited by 103
Heo, D. N., Alioglu, M. A., Wu, Y. B., Özbolat, V., Ayan, B., Dey, M., Kang, Y.-N., & Ozbolat, I. T. (2020) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.0c05096 · Cited by 101
Sun, S., Fei, G., Wang, X., Xie, M., Guo, Q., Fu, D., Wang, Z., Wang, H., Luo, G., & Xia, H. (2021) · Chemical Engineering Journal · doi:10.1016/j.cej.2021.128675 · Cited by 101
Carpio, M. B., Dabaghi, M., Ungureanu, J., Kolb, M. R. J., Hirota, J. A., & Moran-Mirabal, J. M. (2021) · Frontiers in Bioengineering and Biotechnology · doi:10.3389/fbioe.2021.773511 · Cited by 101
“Other studies have used similar approaches to print hydrogels lacking ideal rheological properties for printing (Bhattacharjee et al., 2015; Hinton et al., 2016; Noor et al., 2019; Afghah et al., 2020; Li et al., 2020b) and have even successfully printed bioinks composed solely of cells (Jeon et al.”
BackgroundInfluentialRibezzi, D., Gueye, M., Florczak, S., Dusi, F., de Vos, D., Manente, F., Hierholzer, A., Fussenegger, M., Caiazzo, M., Blunk, T., et al. (2023) · Advanced Materials · doi:10.1002/adma.202301673 · Cited by 102
Complex 3D bioprinting methods
Ji, S., & Güvendiren, M. (2021) · APL Bioengineering · doi:10.1063/5.0034901 · Cited by 100
Embedded bioprinting for designer 3D tissue constructs with complex structural organization
Zeng, X., Meng, Z., He, J., Mao, M., Li, X., Chen, P., Fan, J., & Li, D. (2021) · Acta Biomaterialia · doi:10.1016/j.actbio.2021.11.048 · Cited by 95
3D Bioprinting Stem Cell Derived Tissues
Tasnim, N., la Vega, L. D., Kumar, S. A., Abelseth, L., Alonzo, M., Amereh, M., Joddar, B., & Willerth, S. M. (2018) · Cellular and Molecular Bioengineering · doi:10.1007/s12195-018-0530-2 · Cited by 94
3D printing of thermosets with diverse rheological and functional applicabilities
Sun, Y., Wang, L., Ni, Y., Zhang, H., Cui, X., Li, J., Zhu, Y., Liu, J., Zhang, S., Chen, Y., et al. (2023) · Nature Communications · doi:10.1038/s41467-023-35929-y · Cited by 92
3D printing of silicone and polyurethane elastomers for medical device application: A review
Duran, M. M., Moro, G., Zhang, Y., & Islam, A. (2023) · Advances in Industrial and Manufacturing Engineering · doi:10.1016/j.aime.2023.100125 · Cited by 92
3D Printing Silicone Elastomer for Patient‐Specific Wearable Pulse Oximeter
Abdollahi, S., Markvicka, E. J., Majidi, C., & Feinberg, A. W. (2020) · Advanced Healthcare Materials · doi:10.1002/adhm.201901735 · Cited by 82
Self-citationFreeform 3D printing of soft matters: recent advances in technology for biomedical engineering
Chen, S., Tan, W. S., Juhari, M. A. B., Shi, Q., Cheng, X. S., Chan, W. L., & Song, J. (2020) · Biomedical Engineering Letters · doi:10.1007/s13534-020-00171-8 · Cited by 89
Lin, Y.-H., Chiu, Y., Shen, Y., Wu, Y.-H. A., & Shie, M. (2017) · Journal of Materials Science Materials in Medicine · doi:10.1007/s10856-017-6020-6 · Cited by 86
“3D printing, formally known as additive manufacturing, has the ability to produce products from any customizable CAD files processed from magnetic resonance imaging, computed tomography, or any other imaging capturing methods [17, 18].”
BackgroundFunctional nanocomposites for 3D printing of stretchable and wearable sensors
Abshirini, M., Charara, M., Marashizadeh, P., Saha, M. C., Altan, M. C., & Liu, Y. (2019) · Applied Nanoscience · doi:10.1007/s13204-019-01032-2 · Cited by 86
Mikkonen, R., Puistola, P., Jönkkäri, I., & Mäntysalo, M. (2020) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.9b19632 · Cited by 86
3D reactive inkjet printing of polydimethylsiloxane
Sturgess, C., Tuck, C. J., Ashcroft, I., & Wildman, R. D. (2017) · Journal of Materials Chemistry C · doi:10.1039/c7tc02412f · Cited by 85
Metadata
- Authors
- Hinton, T. J., Hudson, A., Pusch, K., Lee, A., & Feinberg, A. W.
- Affiliations
- Carnegie Mellon University (US)
- Corresponding author
- Feinberg, Adam W.
- Venue
- ACS Biomaterials Science & Engineering
- Publisher
- American Chemical Society (ACS)
- Published
- 2016-05-04
- Volume
- 2
- Issue
- 10
- Pages
- 1781-1786
- ISSN
- 2373-9878 (ISSN-L)
- PMC
- PMC5059754
- OpenAlex
- W2345451752
- Cited by
- 437
- References
- 16
- Citations by year
- 2026: 22 · 2025: 32 · 2024: 44 · 2023: 46 · 2022: 50 · 2021: 68 · 2020: 63 · 2019: 46 · 2018: 41 · 2017: 24 · 2016: 1
- FWCI
- 17.97
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Locations
- ACS Biomaterials Science & Engineering (publishedVersion, cc-by)
- Europe PMC (PubMed Central) (publishedVersion)
- PubMed Central (publishedVersion)
- PubMed (publishedVersion)
- Funders
- U.S. Department of Health and Human Services (DP2HL117750)
- National Science Foundation (1454248)
- Disruptive Health Technology Institute, Carnegie Mellon University (A017261-HIGHMARK-Feinberg)
- Topics
- Physical Sciences › Engineering › Biomedical Engineering › 3D Printing in Biomedical Research
- Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Additive Manufacturing and 3D Printing Technologies
- Physical Sciences › Engineering › Biomedical Engineering › Microfluidic and Capillary Electrophoresis Applications
- Keywords
- support removal, phosphate buffered saline, helical filaments, microfluidics
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.