3D Printing PDMS Elastomer in a Hydrophilic Support Bath via Freeform Reversible Embedding
Open accessThe DOI matches its Crossref record; 16 of the 16 references it cites were found in a registry or an index.
Abstract
Polydimethylsiloxane (PDMS) elastomer is used in a wide range of biomaterial applications including microfluidics, cell culture substrates, flexible electronics, and medical devices. However, it has proved challenging to 3D print PDMS in complex structures due to its low elastic modulus and need for support during the printing process. Here we demonstrate the 3D printing of hydrophobic PDMS prepolymer resins within a hydrophilic Carbopol gel support via freeform reversible embedding (FRE). In the FRE printing process, the Carbopol support acts as a Bingham plastic that yields and fluidizes when the syringe tip of the 3D printer moves through it, but acts as a solid for the PDMS extruded within it. This, in combination with the immiscibility of hydrophobic PDMS in the hydrophilic Carbopol, confines the PDMS prepolymer within the support for curing times up to 72 h while maintaining dimensional stability. After printing and curing, the Carbopol support gel releases the embedded PDMS prints by using phosphate buffered saline solution to reduce the Carbopol yield stress. As proof-of-concept, we used Sylgard 184 PDMS to 3D print linear and helical filaments via continuous extrusion and cylindrical and helical tubes via layer-by-layer fabrication. Importantly, we show that the 3D printed tubes were manifold and perfusable. The results demonstrate that hydrophobic polymers with low viscosity and long cure times can be 3D printed using a hydrophilic support, expanding the range of biomaterials that can be used in additive manufacturing. Further, by implementing the technology using low cost open-source hardware and software tools, the FRE printing technique can be rapidly implemented for research applications.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Figures





Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“Models that replicate the geometrically complex structure of the heart, harboring chambers and large vessels with soft biomaterials, can be achieved using 3D bioprinting.”
From In situ expansion, differentiation, and electromechanical coupling of human cardiac muscle in a 3D bioprinted, chambered organoid (2020) · cites this paper as [12]
Experimental — accuracy not yet measuredThe source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“The concept is gaining traction, as the ability to print tissues composed entirely of native proteins, cells and/or biocompatible synthetic components is possible and accessible to many laboratories9–17.”
From In situ expansion, differentiation, and electromechanical coupling of human cardiac muscle in a 3D bioprinted, chambered organoid (2020) · cites this paper as [12]
Experimental — accuracy not yet measuredThe cited source says what the claim attributes to it.
In the citing paper
“Ultimately, we employed freeform reversible embedding of suspended hydrogels9, 12 with success, wherein our embedding material or “slurry” consisted of gelatin microparticles.”
From In situ expansion, differentiation, and electromechanical coupling of human cardiac muscle in a 3D bioprinted, chambered organoid (2020) · cites this paper as [12]
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Poly(dimethylsiloxane) as a Material for Fabricating Microfluidic Devices
McDonald, J. C., & Whitesides, G. M. (2002) · Accounts of Chemical Research · doi:10.1021/ar010110q · Cited by 2,454
3D bioprinting of vascularized, heterogeneous cell-laden tissue constructs
Kolesky, D. B., Truby, R. L., Gladman, A. S., Busbee, T. A., Homan, K. A., & Lewis, J. A. (2014) · Advanced Materials · doi:10.1002/adma.201305506 · Cited by 2,102
Hinton, T. J., Jallerat, Q., Palchesko, R. N., Park, J. H., Grodzicki, M. S., Shue, H.-J., Ramadan, M. H., Hudson, A. R., & Feinberg, A. W. (2015) · Science Advances · doi:10.1126/sciadv.1500758 · Cited by 1,805
Self-citationThree-dimensional bioprinting of thick vascularized tissues
Kolesky, D. B., Homan, K. A., Skylar-Scott, M. A., & Lewis, J. A. (2016) · Proceedings of the National Academy of Sciences · doi:10.1073/pnas.1521342113 · Cited by 1,492
Mannoor, M. S., Jiang, Z., James, T., Kong, Y. L., Malatesta, K. A., Soboyejo, W. O., Verma, N., Gracias, D. H., & McAlpine, M. C. (2013) · Nano Letters · doi:10.1021/nl4007744 · Cited by 874
Flexible and Stretchable Electronics for Biointegrated Devices
Kim, D.-H., Ghaffari, R., Lu, N., & Rogers, J. A. (2012) · Annual Review of Biomedical Engineering · doi:10.1146/annurev-bioeng-071811-150018 · Cited by 749
Writing in the granular gel medium
Bhattacharjee, T., Zehnder, S. M., Rowe, K. G., Jain, S., Nixon, R. M., Sawyer, W. G., & Angelini, T. E. (2015) · Science Advances · doi:10.1126/sciadv.1500655 · Cited by 635
Integrated 3D-printed reactionware for chemical synthesis and analysis
Symes, M. D., Kitson, P. J., Yan, J., Richmond, C. J., Cooper, G. J. T., Bowman, R. W., Vilbrandt, T., & Cronin, L. (2012) · Nature Chemistry · doi:10.1038/nchem.1313 · Cited by 617
Palchesko, R. N., Zhang, L., Sun, Y., & Feinberg, A. W. (2012) · PLoS ONE · doi:10.1371/journal.pone.0051499 · Cited by 559
Self-citationBélanger, M., & Marois, Y. (2001) · Journal of Biomedical Materials Research · doi:10.1002/jbm.1043 · Cited by 471
Research works printed but not linked: 3
- Ratner, 2013, Biomaterials Science: An Introduction to Materials in Medicine, 1573
- Lipton, J. I.; Angle, S.; Lipson, H. 3D Printable Wax-Silicone Actuators. In 2014 Annual International Solid Freeform Fabrication Symposium;Austin, TX, Aug 4–6, 2014; Laboratory for Freeform Fabrication and University of Texas: Austin, TX, 2014; pp 848–56.
- 2010, Technical Data Sheet 730: Viscosity of Carbopol* Polymers in Aqueous Systems, 1
Cited by
Items 101–200 of 481
Hamidi, A., & Tadesse, Y. T. (2019) · Materials & Design · doi:10.1016/j.matdes.2019.108324 · Cited by 83
“In another method called freeform reversible embedding (FRE), silicone is printed and cured simultaneously inside a vat of another material, which acts as a support bath [29-31].”
MethodKoo, J. M., Kang, J., Shin, S., Jegal, J., Cha, H. G., Choy, S., Hakkarainen, M., Park, J., Oh, D. X., & Hwang, S. Y. (2019) · Composites Science and Technology · doi:10.1016/j.compscitech.2019.107885 · Cited by 82
Integrated Printed Microfluidic Biosensors
Loo, J. F.-C., Ho, A. H. P., Turner, A. P. F., & Mak, W. C. (2019) · Trends in biotechnology · doi:10.1016/j.tibtech.2019.03.009 · Cited by 79
Expert-guided optimization for 3D printing of soft and liquid materials
Abdollahi, S., Davis, A. L., Miller, J. H., & Feinberg, A. W. (2018) · PLoS ONE · doi:10.1371/journal.pone.0194890 · Cited by 78
Self-citation3D-printed miniaturized fluidic tools in chemistry and biology
Dixit, C. K., Kadimisetty, K., & Rusling, J. F. (2018) · TrAC Trends in Analytical Chemistry · doi:10.1016/j.trac.2018.06.013 · Cited by 77
The crossing and integration between microfluidic technology and 3D printing for organ-on-chips
Mi, S., Du, Z., Xu, Y., & Sun, W. (2018) · Journal of Materials Chemistry B · doi:10.1039/c8tb01661e · Cited by 77
3D Direct Printing of Silicone Meniscus Implant Using a Novel Heat-Cured Extrusion-Based Printer
Luis, E., Pan, H. M., Sing, S. L., Bajpai, R. C., Song, J., & Yeong, W. Y. (2020) · Polymers · doi:10.3390/polym12051031 · Cited by 75
“The current state-of-the art in silicone 3D printing includes (a) using UV light of 365 nm to cure UV-sensitive silicone, as they are being deposited layer-by-layer by an inkjet printer (ACEO, Wacker, Munich, Germany), (b) freeform reversible embedding technique using a 2-part A/B silicone where the part A-silicone ca…”
MethodGranular hydrogels for 3D bioprinting applications
Cheng, W., Zhang, J., Liu, J., & Yu, Z. (2020) · View · doi:10.1002/viw.20200060 · Cited by 75
Fluid Bath-Assisted 3D Printing for Biomedical Applications: From Pre- to Postprinting Stages
Hua, W., Mitchell, K., Raymond, L., Godina, B., Zhao, D., Zhou, W., & Jin, Y. (2021) · ACS Biomaterials Science & Engineering · doi:10.1021/acsbiomaterials.1c00910 · Cited by 74
Wu, Q., Zhu, F., Wu, Z. L., Xie, Y., Qian, J. W., Yin, J., & Yang, H. (2022) · npj Flexible Electronics · doi:10.1038/s41528-022-00184-6 · Cited by 74
Krishnamoorthy, S., Zhang, Z., & Xu, C. (2019) · Journal of Biomaterials Applications · doi:10.1177/0885328218823329 · Cited by 77
Printing of Hydrophobic Materials in Fumed Silica Nanoparticle Suspension
Jin, Y., Song, K., Gellermann, N., & Huang, Y. H. (2019) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.9b07433 · Cited by 74
Luis, E., Pan, H. M., Sing, S. L., Bastola, A. K., Goh, G. D., Goh, G. L., Tan, H. K. J., Bajpai, R. C., Song, J., & Yeong, W. Y. (2019) · 3D Printing and Additive Manufacturing · doi:10.1089/3dp.2018.0226 · Cited by 73
Tashman, J. W., Shiwarski, D. J., Coffin, B. D., Ruesch, A., Lanni, F., Kainerstorfer, J. M., & Feinberg, A. W. (2022) · Biofabrication · doi:10.1088/1758-5090/ac975e · Cited by 74
Self-citationNon-planar PDMS microfluidic channels and actuators: a review
Hwang, Y., & Candler, R. N. (2017) · Lab on a Chip · doi:10.1039/c7lc00523g · Cited by 73
Support Optimization for Flat Features via Path Planning in Additive Manufacturing
Jiang, J., Stringer, J., & Xu, X. W. (2018) · 3D Printing and Additive Manufacturing · doi:10.1089/3dp.2017.0124 · Cited by 73
“Current work looking at the use of non-Newtonian fluid baths as a means of support structure presents an intriguing method of further reducing this cost, 23,24 although the range of material that is compatible with such a bath may be limited.”
Additive manufacturing solidification methodologies for ink formulation
Xu, X., Yang, J., Jonhson, W., Wang, Y., Suwardi, A., Ding, J., Guan, C., & Zhang, D. (2022) · Additive manufacturing · doi:10.1016/j.addma.2022.102939 · Cited by 72
3D Printing of Vascular Tubes Using Bioelastomer Prepolymers by Freeform Reversible Embedding
Savoji, H., Huyer, L. D., Mohammadi, M. H., Lai, B. F. L., Rafatian, N., Bannerman, D., Shoaib, M., Bobicki, E. R., Ramachandran, A., & Radisic, M. (2020) · ACS Biomaterials Science & Engineering · doi:10.1021/acsbiomaterials.9b00676 · Cited by 71
Mahmoudi, M., Burlison, S. R., Moreno, S., & Minary‐Jolandan, M. (2021) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.0c19608 · Cited by 71
Embedded 3D Printing of Multimaterial Polymer Lattices via Graph‐Based Print Path Planning
Weeks, R. D., Truby, R. L., Uzel, S. G. M., & Lewis, J. A. (2022) · Advanced Materials · doi:10.1002/adma.202206958 · Cited by 70
Sun, W., Williamson, A. S., Sukhnandan, R., Majidi, C., Yao, L., Feinberg, A. W., & Webster‐Wood, V. A. (2023) · Advanced Functional Materials · doi:10.1002/adfm.202303659 · Cited by 71
Self-citationCatalytically Initiated Gel-in-Gel Printing of Composite Hydrogels
Basu, A., Saha, A., Goodman, C. J., Shafranek, R. T., & Nelson, A. (2017) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.7b14177 · Cited by 71
Polyelectrolyte scaling laws for microgel yielding near jamming
Bhattacharjee, T., Kabb, C. P., O’Bryan, C. S., Urueña, J. M., Sumerlin, B. S., Sawyer, W. G., & Angelini, T. E. (2018) · Soft Matter · doi:10.1039/c7sm01518f · Cited by 69
Kamat, A. M., Pei, Y. T., Jayawardhana, B., & Kottapalli, A. G. P. (2021) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.0c21295 · Cited by 70
Recent advances in 3D-printing-based organ-on-a-chip
Wu, X., Shi, W., Liu, X., & Gu, Z. (2024) · EngMedicine · doi:10.1016/j.engmed.2024.100003 · Cited by 68
Immersion precipitation 3D printing ( ip 3DP)
Karyappa, R. B., Ohno, A., & Hashimoto, M. (2019) · Materials Horizons · doi:10.1039/c9mh00730j · Cited by 67
Tashman, J. W., Shiwarski, D. J., & Feinberg, A. W. (2021) · HardwareX · doi:10.1016/j.ohx.2020.e00170 · Cited by 67
“With recent advances in embedded 3D printing approaches, such as FRESH, the materials are supported during the printing process, but improved extrusion capability is necessary [8].”
MethodSelf-citationPreparation of Smart Materials by Additive Manufacturing Technologies: A Review
Mondal, K., & Tripathy, P. K. (2021) · Materials · doi:10.3390/ma14216442 · Cited by 67
“Reprinted with permission from Ref [43], Copyright”
Rothbauer, M., Eilenberger, C., Spitz, S., Bachmann, B., Kratz, S. R. A., Reihs, E. I., Windhager, R., Toegel, S., & Ertl, P. (2022) · Frontiers in Bioengineering and Biotechnology · doi:10.3389/fbioe.2022.837087 · Cited by 66
“The droplet and inkjet-based printers require a solution viscosity of 10 mPa.s, whereas the extrusion-based involves a minimum of 30–6 × 107 mPa.s However, laser-assisted printing, requires a viscosity of 1–300 mPa.s (Hölzl et al., 2016; Ozbolat et al., 2016).”
BackgroundEmbedded 3D printing of multi-internal surfaces of hydrogels
Zhao, J., Hussain, M., Wang, M., Li, Z., & He, N. (2020) · Additive manufacturing · doi:10.1016/j.addma.2020.101097 · Cited by 67
Li, J., Niu, H., Yu, Y., Gao, Y., Wu, Q., Wang, F., & Sun, P. (2021) · ACS Applied Polymer Materials · doi:10.1021/acsapm.1c00271 · Cited by 65
Simulated filament shapes in embedded 3D printing
Friedrich, L. M., & Seppala, J. E. (2021) · Soft Matter · doi:10.1039/d1sm00731a · Cited by 65
3D bioprinting from the micrometer to millimeter length scales: Size does matter
Hinton, T. J., Lee, A. R., & Feinberg, A. W. (2017) · Current Opinion in Biomedical Engineering · doi:10.1016/j.cobme.2017.02.004 · Cited by 65
Self-citationLan, X., Liang, Y., Erkut, E. J. N., Kunze, M., Mulet‐Sierra, A., Gong, T., Osswald, M., Ansari, K., Seikaly, H. R., Boluk, Y., et al. (2021) · The FASEB Journal · doi:10.1096/fj.202002081r · Cited by 65
Powder bed binder jetting additive manufacturing of silicone structures
Liravi, F., & Vlasea, M. (2018) · Additive manufacturing · doi:10.1016/j.addma.2018.02.017 · Cited by 65
Ludwig, P. E., Huff, T. J., & Zuñiga, J. M. (2018) · Journal of Tissue Engineering · doi:10.1177/2041731418769863 · Cited by 62
Direct ink writing techniques for in situ gelation and solidification
Wilt, J. K., Gilmer, D., Kim, S., Compton, B. G., & Saito, T. (2021) · MRS Communications · doi:10.1557/s43579-020-00006-8 · Cited by 62
Li, Y.-C. E., Jodat, Y. A., Samanipour, R., Zorzi, G., Zhu, K., Hirano, M., Chang, K., Arnaout, A., Hassan, S., Matharu, N., et al. (2021) · Biofabrication · doi:10.1088/1758-5090/abc1be · Cited by 61
Embedded direct ink writing of freeform ceramic components
Huang, K., Elsayed, H., Franchin, G., & Colombo, P. (2021) · Applied Materials Today · doi:10.1016/j.apmt.2021.101005 · Cited by 61
Li, H., Tan, Y. J., Kiran, R., Tor, S. B., & Zhou, K. (2021) · Additive Manufacturing · doi:10.1016/j.addma.2020.101640 · Cited by 53
Chen, S., Jang, T., Pan, H. M., Jung, H., Sia, M. W., Xie, S., Hang, Y., Chong, S. K. M., Wang, D., & Song, J. (2020) · International Journal of Bioprinting · doi:10.18063/ijb.v6i2.258 · Cited by 61
Cheng, C., Chen, Y., Lee, A. K.-X., Yao, C., & Shie, M. (2019) · Journal of Materials Science Materials in Medicine · doi:10.1007/s10856-019-6279-x · Cited by 60
Self-citationАржакова, О. В., Arzhakov, M. S., Badamshina, E. R., Bryuzgina, E. B., Bryuzgin, E. V., Bystrova, A. V., Vaganov, G., Vasilevskaya, V. V., Vdovichenko, A. Y., Gallyamov, M. O., et al. (2022) · Russian Chemical Reviews · doi:10.57634/rcr5062 · Cited by 60
Brunel, L. G., Christakopoulos, F., Kilian, D., Cai, B., Hull, S. M., Myung, D. J., & Heilshorn, S. C. (2023) · Advanced Healthcare Materials · doi:10.1002/adhm.202303325 · Cited by 59
Facile Photo and Thermal Two‐Stage Curing for High‐Performance 3D Printing of Poly(Dimethylsiloxane)
Ji, Z., Jiang, D. M., Zhang, X., Guo, Y., & Wang, X. (2020) · Macromolecular Rapid Communications · doi:10.1002/marc.202000064 · Cited by 59
Bioprinted microvasculature: progressing from structure to function
Seymour, A. J., Westerfield, A. D., Cornelius, V., Skylar‐Scott, M. A., & Heilshorn, S. C. (2022) · Biofabrication · doi:10.1088/1758-5090/ac4fb5 · Cited by 59
“While this copolymer is primarily marketed as a thickening agent for surfactant systems, such as shampoo and body wash, it has found applications in fields such as drug delivery and bioprinting [46].”
Simultaneous multi-material embedded printing for 3D heterogeneous structures
Gao, Z., Yin, J. L., Liu, P., Li, Q., Zhang, R., Yang, H., & Zhou, H. (2023) · International Journal of Extreme Manufacturing · doi:10.1088/2631-7990/acd285 · Cited by 58
“The structural integrity problems of themulti-layered structure printed by the embedding printing method has been reported [23, 24].”
BackgroundMethodLi, Y., Wu, Z., Chen, Y., Xian, S., Hong, Z., Wang, Q., Jiang, P., Yu, H., & Zhong, Y. (2024) · Additive manufacturing · doi:10.1016/j.addma.2024.104178 · Cited by 58
Davoodi, E., Montazerian, H., Khademhosseini, A., & Toyserkani, E. (2020) · Acta Biomaterialia · doi:10.1016/j.actbio.2020.10.001 · Cited by 58
Scaling Printable Zn–Ag2O Batteries for Integrated Electronics
Kumar, R., Johnson, K. M., Williams, N. X., & Subramanian, V. (2019) · Advanced Energy Materials · doi:10.1002/aenm.201803645 · Cited by 57
Extrusion-based 3D Printing and Characterization of Edible Materials
Huang, C. Y. (2018) · UWSpace (University of Waterloo) · Cited by 56
Emerging 3D printing technologies and methodologies for microfluidic development
Kabandana, G. K. M., Zhang, T., & Chen, C. (2022) · Analytical Methods · doi:10.1039/d2ay00798c · Cited by 55
Schneider, K. H., Goldberg, B. J., Hasturk, O., Mu, X., Dötzlhofer, M., Eder, G., Theodossiou, S. K., Pichelkastner, L., Riess, P., Rohringer, S., et al. (2023) · Biomaterials Research · doi:10.1186/s40824-023-00431-5 · Cited by 55
“Recently, an innovative extrusion-based bioprinting technique was developed that is capable of printing soft, cell-encapsulating and low viscosity bioinks, based on a freeform reversible embedding of suspended hydrogels or FRESH [29].”
MethodJung, Y. J., Jung, K., Park, B., Choi, J.-H., Kim, D., Park, J., Ko, J. S., & Cho, H. (2019) · Micro and Nano Systems Letters · doi:10.1186/s40486-019-0097-2 · Cited by 54
3D Cell Printing of Tissue/Organ-Mimicking Constructs for Therapeutic and Drug Testing Applications
Kim, J., Kong, J. S., Han, W., Kim, B. S., & Cho, D. (2020) · International Journal of Molecular Sciences · doi:10.3390/ijms21207757 · Cited by 54
“The freeform reversible embedding of suspended hydrogels (FRESH) method has been proposed to obtain a stable 3D structure with a hydrogel-based bioink [97,98].”
MethodStructure–Mechanical Property Relationships of 3D-Printed Porous Polydimethylsiloxane
Woo, R., Chen, G., Zhao, J., & Bae, J. (2021) · ACS Applied Polymer Materials · doi:10.1021/acsapm.1c00417 · Cited by 54
Tao, R., Granier, F., & Therriault, D. (2022) · Additive manufacturing · doi:10.1016/j.addma.2022.103243 · Cited by 53
Suppression of Filament Defects in Embedded 3D Printing
Friedrich, L. M., Gunther, R. T., & Seppala, J. E. (2022) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.2c08047 · Cited by 53
Hamidi, A., & Tadesse, Y. T. (2018) · Composite Structures · doi:10.1016/j.compstruct.2018.11.019 · Cited by 52
“Recently, a few methods for 3D printing silicone rubbers have been developed, which are mostly based on the direct ink writing [34,35].”
Background3D printing low-stiffness silicone within a curable support matrix
Greenwood, T. E., Hatch, S. E., Colton, M. B., & Thomson, S. L. (2020) · Additive manufacturing · doi:10.1016/j.addma.2020.101681 · Cited by 51
“Print defects, poor material adhesion, and altered material properties have similarly been noted in other works [51, 54, 58].”
Background3D printing with silk: considerations and applications
DeBari, M. K., Keyser, M. N., Bai, M. A., & Abbott, R. D. (2018) · Connective Tissue Research · doi:10.1080/03008207.2018.1553959 · Cited by 47
Digital light processing 3D printing of modified liquid isoprene rubber using thiol-click chemistry
Strohmeier, L., Frommwald, H., & Schlögl, S. (2020) · RSC Advances · doi:10.1039/d0ra04186f · Cited by 47
Navara, A. M., Kim, Y. S., Xu, Y., Crafton, C. L., Diba, M., Guo, J. L., & Mikos, A. G. (2021) · Bioactive Materials · doi:10.1016/j.bioactmat.2021.11.016 · Cited by 46
Freeform Liquid 3D Printing of Soft Functional Components for Soft Robotics
Calais, T., Sanandiya, N. D., Jain, S., Kanhere, E. V., Kumar, S., Yeow, C., & y Alvarado, P. V. (2021) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.1c20209 · Cited by 46
Extrusion-based printing of sacrificial Carbopol ink for fabrication of microfluidic devices
Özbolat, V., Dey, M., Ayan, B., & Ozbolat, I. T. (2019) · Biofabrication · doi:10.1088/1758-5090/ab10ae · Cited by 46
Microextrusion Based 3D Printing – A Review
Udofia, E. N., & Zhou, W. (2018) · doi:10.26153/tsw/17201 · Cited by 46
Fabrication of truly 3D microfluidic channel using 3D-printed soluble mold
Kang, K., Oh, S., Yi, H., Han, S., & Hwang, Y. (2018) · Biomicrofluidics · doi:10.1063/1.5012548 · Cited by 46
Walker, S., Daalkhaijav, U., Thrush, D., Branyan, C., Yirmibeşoğlu, O. D., Olson, G., & Mengüç, Y. (2019) · 3D Printing and Additive Manufacturing · doi:10.1089/3dp.2018.0117 · Cited by 45
A short survey of sustainable material extrusion additive manufacturing
Jiang, J., & Fu, Y.-F. (2020) · Australian Journal of Mechanical Engineering · doi:10.1080/14484846.2020.1825045 · Cited by 44
Zhang, Z., Liu, Y., Yang, K., Chen, D., Li, S., & Li, Z. (2022) · Materials Chemistry and Physics · doi:10.1016/j.matchemphys.2022.126564 · Cited by 44
Current developments in 3D bioprinting for tissue engineering
Cornelissen, D.-J., Faulkner‐Jones, A., & Shu, W. (2017) · Current Opinion in Biomedical Engineering · doi:10.1016/j.cobme.2017.05.004 · Cited by 44
“In FRESH the supporting material is composed of a slurry of gelatin microparticles which is melted and washed away by simply raising the temperature to 37 °C when the structure is completed [2].”
MethodInfluentialA Guiding Framework for Microextrusion Additive Manufacturing
Udofia, E. N., & Zhou, W. (2019) · Journal of Manufacturing Science and Engineering · doi:10.1115/1.4042607 · Cited by 43
Emerging Applications of Additive Manufacturing in Biosensors and Bioanalytical Devices
Ruan, X., Wang, Y., Cheng, N., Niu, X., Chang, Y., Li, L., Du, D., & Lin, Y. (2020) · Advanced Materials Technologies · doi:10.1002/admt.202000171 · Cited by 44
Most Important Biomedical and Pharmaceutical Applications of Silicones
Chruściel, J. J. (2025) · Materials · doi:10.3390/ma18112561 · Cited by 42
3-D printed soft magnetic helical coil actuators of iron oxide embedded polydimethylsiloxane
Bayaniahangar, R., Ahangar, S. B., Zhang, Z., Lee, B. P., & Pearce, J. M. (2020) · Sensors and Actuators B Chemical · doi:10.1016/j.snb.2020.128781 · Cited by 42
FRESH bioprinting of biodegradable chitosan thermosensitive hydrogels
Rahimnejad, M., Adoungotchodo, A., Demarquette, N. R., & Lerouge, S. (2022) · Bioprinting · doi:10.1016/j.bprint.2022.e00209 · Cited by 42
“Carbopol microgels are anionic [19] and not recommended for use with cationic hydrogels such as chitosan [20].”
BackgroundAdditive Manufacturing of Overhang Structures Using Moisture-Cured Silicone with Support Material
Muthusamy, M., Safaee, S., & Chen, R. K. (2018) · Journal of Manufacturing and Materials Processing · doi:10.3390/jmmp2020024 · Cited by 41
“In comparison to the process of hydrostatic 3D printing of silicone [17,18], an advantage of using the extrusion-based process with a support structure is its dimensional accuracy, along with fewer process complications.”
BackgroundZhou, K., Dey, M., Ayan, B., Zhang, Z., Özbolat, V., Kim, M.-H., Khristov, V., & Ozbolat, I. T. (2021) · Biomedical Materials · doi:10.1088/1748-605x/abe55e · Cited by 42
“Additivemanufacturing within Carbopol support bath allows for 3D printing of otherwise unachievable PDMS structures; however, generation of defined microfluidic channels is quite challenging due to limited resolution of PDMS printing in support baths [15].”
Resolution of 3D bioprinting inside bulk gel and granular gel baths
Xie, Z., Kang, D., & Matsusaki, M. (2021) · Soft Matter · doi:10.1039/d1sm00926e · Cited by 41
Tan, W. S., Juhari, M. A. B., Shi, Q., Chen, S., Campolo, D., & Song, J. (2020) · Additive manufacturing · doi:10.1016/j.addma.2020.101563 · Cited by 40
Use of FDM Technology in Healthcare Applications: Recent Advances
Buj-Corral, I., Tejo‐Otero, A., & Fenollosa-Artés, F. (2021) · Materials forming, machining and tribology · doi:10.1007/978-3-030-68024-4_15 · Cited by 40
Associative Liquid‐In‐Liquid 3D Printing Techniques for Freeform Fabrication of Soft Matter
Honaryar, H., Amirfattahi, S., & Niroobakhsh, Z. (2023) · Small · doi:10.1002/smll.202206524 · Cited by 41
3D embedded printing of microfluidic devices using a functional silicone composite support bath
Alioglu, M. A., Singh, Y. P., Nagamine, M., Rizvi, S. H. A., Pal, V., Gerhard, E. M., Saini, S., Kim, M.-H., & Ozbolat, I. T. (2023) · Additive manufacturing · doi:10.1016/j.addma.2023.103566 · Cited by 40
A 3D bioprinted cortical organoid platform for modeling human brain development
Cadena, M. A., Sing, A., Taylor, K., Jin, L., Ning, L., Salar Amoli, M., Singh, Y., Lanjewar, S. N., Tomov, M. L., Serpooshan, V., et al. (2024) · Advanced Healthcare Materials · doi:10.1002/adhm.202401603 · Cited by 39
Fast 3D printing of fine, continuous, and soft fibers via embedded solvent exchange
Eom, W., Hossain, M. T., Parasramka, V., Kim, J., Siu, R., Sanders, K. A., Piorkowski, D., Lowe, A., Koh, H. G., Volder, M. F. L. D., et al. (2025) · Nature Communications · doi:10.1038/s41467-025-55972-1 · Cited by 39
Charara, M., Abshirini, M., Saha, M. C., Altan, M. C., & Liu, Y. (2019) · Journal of Intelligent Material Systems and Structures · doi:10.1177/1045389x19835953 · Cited by 39
“In particular, PDMS, as a flexible, biocompatible, and environmentally friendly elastomer, has been successfully 3D printed (Hinton et al., 2015, 2016; Ozbolat et al., 2018), as have other elastomer-based nanocomposites, such as carbon grease (Muth et al., 2014).”
BackgroundReeser, K., & Doiron, A. L. (2019) · 3D Printing and Additive Manufacturing · doi:10.1089/3dp.2019.0058 · Cited by 39
Nian, S., Zhu, J., Zhang, H., Gong, Z., Freychet, G., Zhernenkov, M., Xu, B., & Cai, L. (2021) · Chemistry of Materials · doi:10.1021/acs.chemmater.0c04659 · Cited by 40
Engineering Natural Pollen Grains as Multifunctional 3D Printing Materials
Chen, S., Shi, Q., Jang, T., Ibrahim, M. S., Deng, J., Ferracci, G., Tan, W. S., Cho, N., & Song, J. (2021) · Advanced Functional Materials · doi:10.1002/adfm.202106276 · Cited by 39
Fabrication of 3D GelMA Scaffolds Using Agarose Microgel Embedded Printing
Yang, B., Liu, T., Gao, G., Zhang, X., & Wu, B. (2022) · Micromachines · doi:10.3390/mi13030469 · Cited by 39
Wu, Y. B., Yang, X., Gupta, D., Alioglu, M. A., Qin, M., Özbolat, V., Li, Y., & Ozbolat, I. T. (2024) · Advanced Functional Materials · doi:10.1002/adfm.202313088 · Cited by 38
Characterization of 3D-Printed Moulds for Soft Lithography of Millifluidic Devices
Fuad, N. M., Carve, M., Kaslin, J., & Włodkowic, D. (2018) · Micromachines · doi:10.3390/mi9030116 · Cited by 38
Engineering Three-Dimensional Vascularized Cardiac Tissues
Williams, M. A. C., Mair, D. B., Lee, W., Lee, E., & Kim, D. (2021) · Tissue Engineering Part B Reviews · doi:10.1089/ten.teb.2020.0343 · Cited by 39
Putra, K. B., Tian, X., Plott, J. S., & Shih, A. J. (2020) · Journal of the mechanical behavior of biomedical materials/Journal of mechanical behavior of biomedical materials · doi:10.1016/j.jmbbm.2020.103733 · Cited by 37
Wang, H., Song, H., Yang, Y., Cao, Q., Hu, Y., Chen, J., Guo, J., Wang, Y., Jia, D. T., Cao, S., et al. (2020) · BioMedical Engineering OnLine · doi:10.1186/s12938-020-00822-y · Cited by 37
Predicting interfacial layer adhesion strength in 3D printable silicone
Walker, S., Lingle, E., Troxler, N., Wallin, T. J., Healy, K., Mengüç, Y., & Davidson, J. R. (2021) · Additive manufacturing · doi:10.1016/j.addma.2021.102320 · Cited by 37
Additive‐Free, Gelled Nanoinks as a 3D Printing Toolbox for Hierarchically Structured Bulk Aerogels
Rebber, M., Trommler, M., Lokteva, I., Ehteram, S., Schropp, A., König, S. G., Fröba, M., & Koziej, D. (2022) · Advanced Functional Materials · doi:10.1002/adfm.202112914 · Cited by 37
UV-curable silicone materials with tuneable mechanical properties for 3D printing
Foerster, A., Annarasa, V., Terry, A., Wildman, R. D., Hague, R., Irvine, D. J., Focatiis, D. S. A. D., & Tuck, C. J. (2021) · Materials & Design · doi:10.1016/j.matdes.2021.109681 · Cited by 36
“Alternative methods such as Freeform Reversible Embedding (FRE) offer contact-based support-free solutions for the 3D printing of silicone [28].”
MethodWang, Q., Chen, A., Gu, H., Qin, G., Zhang, J., Xu, J., Jiang, G., Liu, W., Zhang, Z., & Huang, H. (2021) · Journal of Materials Science · doi:10.1007/s10853-021-06052-4 · Cited by 36
López-Donaire, M. L., Izuzquiza, G. D. A., Garzon-Hernandez, S., Crespo‐Miguel, J., la Torre, M. F.-D., de Velasco, D. A. O.-G., & Garcia‐Gonzalez, D. (2022) · Advanced Materials Technologies · doi:10.1002/admt.202201707 · Cited by 36
Metadata
- Authors
- Hinton, T. J., Hudson, A., Pusch, K., Lee, A., & Feinberg, A. W.
- Affiliations
- Carnegie Mellon University (US)
- Corresponding author
- Feinberg, Adam W.
- Venue
- ACS Biomaterials Science & Engineering
- Publisher
- American Chemical Society (ACS)
- Published
- 2016-05-04
- Volume
- 2
- Issue
- 10
- Pages
- 1781-1786
- ISSN
- 2373-9878 (ISSN-L)
- PMC
- PMC5059754
- OpenAlex
- W2345451752
- Cited by
- 437
- References
- 16
- Citations by year
- 2026: 22 · 2025: 32 · 2024: 44 · 2023: 46 · 2022: 50 · 2021: 68 · 2020: 63 · 2019: 46 · 2018: 41 · 2017: 24 · 2016: 1
- FWCI
- 17.97
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Locations
- ACS Biomaterials Science & Engineering (publishedVersion, cc-by)
- Europe PMC (PubMed Central) (publishedVersion)
- PubMed Central (publishedVersion)
- PubMed (publishedVersion)
- Funders
- U.S. Department of Health and Human Services (DP2HL117750)
- National Science Foundation (1454248)
- Disruptive Health Technology Institute, Carnegie Mellon University (A017261-HIGHMARK-Feinberg)
- Topics
- Physical Sciences › Engineering › Biomedical Engineering › 3D Printing in Biomedical Research
- Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Additive Manufacturing and 3D Printing Technologies
- Physical Sciences › Engineering › Biomedical Engineering › Microfluidic and Capillary Electrophoresis Applications
- Keywords
- support removal, phosphate buffered saline, helical filaments, microfluidics
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.