3D Printing PDMS Elastomer in a Hydrophilic Support Bath via Freeform Reversible Embedding
Open accessThe DOI matches its Crossref record; 16 of the 16 references it cites were found in a registry or an index.
Abstract
Polydimethylsiloxane (PDMS) elastomer is used in a wide range of biomaterial applications including microfluidics, cell culture substrates, flexible electronics, and medical devices. However, it has proved challenging to 3D print PDMS in complex structures due to its low elastic modulus and need for support during the printing process. Here we demonstrate the 3D printing of hydrophobic PDMS prepolymer resins within a hydrophilic Carbopol gel support via freeform reversible embedding (FRE). In the FRE printing process, the Carbopol support acts as a Bingham plastic that yields and fluidizes when the syringe tip of the 3D printer moves through it, but acts as a solid for the PDMS extruded within it. This, in combination with the immiscibility of hydrophobic PDMS in the hydrophilic Carbopol, confines the PDMS prepolymer within the support for curing times up to 72 h while maintaining dimensional stability. After printing and curing, the Carbopol support gel releases the embedded PDMS prints by using phosphate buffered saline solution to reduce the Carbopol yield stress. As proof-of-concept, we used Sylgard 184 PDMS to 3D print linear and helical filaments via continuous extrusion and cylindrical and helical tubes via layer-by-layer fabrication. Importantly, we show that the 3D printed tubes were manifold and perfusable. The results demonstrate that hydrophobic polymers with low viscosity and long cure times can be 3D printed using a hydrophilic support, expanding the range of biomaterials that can be used in additive manufacturing. Further, by implementing the technology using low cost open-source hardware and software tools, the FRE printing technique can be rapidly implemented for research applications.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Figures





Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“Models that replicate the geometrically complex structure of the heart, harboring chambers and large vessels with soft biomaterials, can be achieved using 3D bioprinting.”
From In situ expansion, differentiation, and electromechanical coupling of human cardiac muscle in a 3D bioprinted, chambered organoid (2020) · cites this paper as [12]
Experimental — accuracy not yet measuredThe source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“The concept is gaining traction, as the ability to print tissues composed entirely of native proteins, cells and/or biocompatible synthetic components is possible and accessible to many laboratories9–17.”
From In situ expansion, differentiation, and electromechanical coupling of human cardiac muscle in a 3D bioprinted, chambered organoid (2020) · cites this paper as [12]
Experimental — accuracy not yet measuredThe cited source says what the claim attributes to it.
In the citing paper
“Ultimately, we employed freeform reversible embedding of suspended hydrogels9, 12 with success, wherein our embedding material or “slurry” consisted of gelatin microparticles.”
From In situ expansion, differentiation, and electromechanical coupling of human cardiac muscle in a 3D bioprinted, chambered organoid (2020) · cites this paper as [12]
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Poly(dimethylsiloxane) as a Material for Fabricating Microfluidic Devices
McDonald, J. C., & Whitesides, G. M. (2002) · Accounts of Chemical Research · doi:10.1021/ar010110q · Cited by 2,454
3D bioprinting of vascularized, heterogeneous cell-laden tissue constructs
Kolesky, D. B., Truby, R. L., Gladman, A. S., Busbee, T. A., Homan, K. A., & Lewis, J. A. (2014) · Advanced Materials · doi:10.1002/adma.201305506 · Cited by 2,102
Hinton, T. J., Jallerat, Q., Palchesko, R. N., Park, J. H., Grodzicki, M. S., Shue, H.-J., Ramadan, M. H., Hudson, A. R., & Feinberg, A. W. (2015) · Science Advances · doi:10.1126/sciadv.1500758 · Cited by 1,805
Self-citationThree-dimensional bioprinting of thick vascularized tissues
Kolesky, D. B., Homan, K. A., Skylar-Scott, M. A., & Lewis, J. A. (2016) · Proceedings of the National Academy of Sciences · doi:10.1073/pnas.1521342113 · Cited by 1,492
Mannoor, M. S., Jiang, Z., James, T., Kong, Y. L., Malatesta, K. A., Soboyejo, W. O., Verma, N., Gracias, D. H., & McAlpine, M. C. (2013) · Nano Letters · doi:10.1021/nl4007744 · Cited by 874
Flexible and Stretchable Electronics for Biointegrated Devices
Kim, D.-H., Ghaffari, R., Lu, N., & Rogers, J. A. (2012) · Annual Review of Biomedical Engineering · doi:10.1146/annurev-bioeng-071811-150018 · Cited by 749
Writing in the granular gel medium
Bhattacharjee, T., Zehnder, S. M., Rowe, K. G., Jain, S., Nixon, R. M., Sawyer, W. G., & Angelini, T. E. (2015) · Science Advances · doi:10.1126/sciadv.1500655 · Cited by 635
Integrated 3D-printed reactionware for chemical synthesis and analysis
Symes, M. D., Kitson, P. J., Yan, J., Richmond, C. J., Cooper, G. J. T., Bowman, R. W., Vilbrandt, T., & Cronin, L. (2012) · Nature Chemistry · doi:10.1038/nchem.1313 · Cited by 617
Palchesko, R. N., Zhang, L., Sun, Y., & Feinberg, A. W. (2012) · PLoS ONE · doi:10.1371/journal.pone.0051499 · Cited by 559
Self-citationBélanger, M., & Marois, Y. (2001) · Journal of Biomedical Materials Research · doi:10.1002/jbm.1043 · Cited by 471
Research works printed but not linked: 3
- Ratner, 2013, Biomaterials Science: An Introduction to Materials in Medicine, 1573
- Lipton, J. I.; Angle, S.; Lipson, H. 3D Printable Wax-Silicone Actuators. In 2014 Annual International Solid Freeform Fabrication Symposium;Austin, TX, Aug 4–6, 2014; Laboratory for Freeform Fabrication and University of Texas: Austin, TX, 2014; pp 848–56.
- 2010, Technical Data Sheet 730: Viscosity of Carbopol* Polymers in Aqueous Systems, 1
Cited by
Items 301–400 of 481
From shallow waters to Mariana Trench: a survey of bio-inspired underwater soft robots
Wang, J., Du, P., Zhang, Y., Xie, Z., & Laschi, C. (2026) · Bioinspiration & Biomimetics · doi:10.1088/1748-3190/ae3af2 · Cited by 12
“Such actuators employing specially formulated dielectric liquids to transmit driving forces have enabled soft fish to reach depths of over 4000 m for untethered swimming [146].”
3D printing‐based full‐scale human brain for diverse applications
Hua, W., Zhang, C., Raymond, L., Mitchell, K., Wen, L., Yang, Y., Zhao, D., Liu, S., & Jin, Y. (2023) · Brain‐X · doi:10.1002/brx2.5 · Cited by 12
“First, current support bath materials [23–27] possess poor flowability at working status due to their high yield stresses (ranging from tens to hundreds of Pascals [20,22,28,29] ), making it extremely challenging to add support bath materials during printing and eventually constraining the overall size of achievable s…”
BackgroundBiofabrication in Tissue Engineering
Bao, G. (2020) · Springer eBooks · doi:10.1007/978-3-030-34471-9_12 · Cited by 12
Wychowaniec, J. K., Bektas, E. I., Mürner, M., Sapudom, J., Šrejber, M., Airoldi, M., Schmidt, R., Vernengo, J., Edwards‐Gayle, C. J. C., Tipay, P. S., et al. (2025) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.4c19900 · Cited by 11
Barua, R., Das, D., & Biswas, N. (2025) · Biomicrofluidics · doi:10.1063/5.0268362 · Cited by 10
Embedded 3D printing: material-structure-function deep integration
Yi, H., Niu, Z., Cao, H., Luo, J., An, J., & Chua, C. K. (2026) · Materials Today · doi:10.1016/j.mattod.2026.103227 · Cited by 10
Growing human-scale scala tympani-like in vitro cell constructs
Robles, U. A. A., Tomasetig, F., & Poole-Warren, L. A. (2023) · Biofabrication · doi:10.1088/1758-5090/accfc0 · Cited by 10
“3D printing) is challenging due to viscosity and curing times, which to can lead to inaccurate printing fidelity [29].”
BackgroundAspects of a Suspended Bioprinting System Affect Cell Viability and Support Bath Properties
Navara, A. M., Xu, Y., Perez, M. R., & Mikos, A. G. (2023) · Tissue Engineering Part A · doi:10.1089/ten.tea.2023.0097 · Cited by 10
Residual Stress‐Driven Non‐Euclidean Morphing in Origami Structures
Liang, Z., Chai, S., Ding, Q., Xiao, K., Liu, P., Ma, J., & Ju, J. (2024) · Advanced Intelligent Systems · doi:10.1002/aisy.202400246 · Cited by 10
Filament Disturbance and Fusion during Embedded 3D Printing of Silicones
Friedrich, L. M., & Woodcock, J. W. (2024) · ACS Biomaterials Science & Engineering · doi:10.1021/acsbiomaterials.4c01014 · Cited by 10
Hossain, M. T., Eom, W., Shah, A., Lowe, A., Fudge, D. S., Tawfick, S., & Ewoldt, R. H. (2025) · Journal of Non-Newtonian Fluid Mechanics · doi:10.1016/j.jnnfm.2025.105440 · Cited by 10
Freeform liquid 3D printing of hydraulically enhanced dielectric actuators
Calais, T., Ugalde, A. C., Chooi, A., & y Alvarado, P. V. (2022) · Materials Today Proceedings · doi:10.1016/j.matpr.2022.08.549 · Cited by 10
A 3D printable and self‐healing polydimethylsiloxane elastomer
Wei, Z., Wang, H., & Li, C. (2023) · Journal of Polymer Science · doi:10.1002/pol.20230427 · Cited by 10
Biermann, T., Mesecke, L., Teves, S., Ziesche, I., & Lachmayer, R. (2025) · Materials · doi:10.3390/ma18133164 · Cited by 9
“Due to their high flexibility, chemical stability, and optical transparency, silicone elastomers are used in soft robotics [1–3], biomedical devices [4–6], microfluidic networks [7,8], as well as optical applications [9].”
Gel-Based Suspension Medium Used in 3D Bioprinting for Constructing Tissue/Organ Analogs
Luo, Y., Xu, R., Hu, Z., Ni, R., Zhu, T., Zhang, H., & Zhu, Y. (2024) · Gels · doi:10.3390/gels10100644 · Cited by 9
On-Demand Radial Electrodeposition of Alginate Tubular Structures
Kingsley, D. M., Capuano, J. A., & Corr, D. T. (2019) · ACS Biomaterials Science & Engineering · doi:10.1021/acsbiomaterials.9b00415 · Cited by 9
Tissue Engineering Models for the Study of Breast Neoplastic Disease and the Tumor Microenvironment
Premaratne, I. D., Toyoda, Y., Celie, K., Brown, K. A., & Spector, J. A. (2020) · Tissue Engineering Part B Reviews · doi:10.1089/ten.teb.2019.0347 · Cited by 9
“83 Through this additive manufacturing process, termed freeform reversible embedding (FRE), this group was able to circumvent the otherwise prohibitive challenge of the elastomer’s low elastic modulus, which demands a need for support during the printing process.”
Additive manufacturing of biomaterials
Torre, M., Giannitelli, S. M., Mauri, E., Trombetta, M., & Rainer, A. (2021) · Advances in chemical engineering · doi:10.1016/bs.ache.2021.03.003 · Cited by 9
Soft-tissue-mimicking using silicones for the manufacturing of soft phantoms by fresh 3D printing
Tejo‐Otero, A., Colly, A., Courtial, E., Fenollosa-Artés, F., Buj-Corral, I., & Marquette, C. A. (2021) · Rapid Prototyping Journal · doi:10.1108/rpj-04-2021-0079 · Cited by 9
Optimization of helical dielectric elastomer actuator with additive manufacturing
Kim, D., Park, J. H., Divo, E., & Atrache, A. E. (2018) · Electroactive Polymer Actuators, Sensors, and Devices (EAPAD) · doi:10.1117/12.2296720 · Cited by 8
“Freeform reversible embedding method by Hinton suggests a method to 3D print PDMS elastomer in a hydrophilic support bath that is designed to enable true freeform fabrication of complex structures [7].”
MethodVera, G., Tisato, S., Nekoonam, N., Shakeel, A., Garfias, S., & Helmer, D. (2024) · Advanced Materials Technologies · doi:10.1002/admt.202400533 · Cited by 8
Kotani, T., Hananouchi, T., & Sakai, S. (2025) · Biomedical Materials · doi:10.1088/1748-605x/adc0d6 · Cited by 8
“Embedded bioprinting was developed to solve this problem [29, 30].”
Bioinks for Three-Dimensional Printing in Regenerative Medicine
Navarro, J., Calderon, G. A., Miller, J. S., & Fisher, J. P. (2018) · Elsevier eBooks · doi:10.1016/b978-0-12-809880-6.00046-1 · Cited by 8
Redondo, F. L., Ninago, M. D., de Freitas, A. G. O., Giacomelli, C., Ciolino, A. E., & Villar, M. A. (2018) · International Journal of Polymer Science · doi:10.1155/2018/8252481 · Cited by 8
Zhang, Y.-C., Xue, Y., Ogawa, T., Wada, S., & Wang, J. (2023) · ACS Applied Engineering Materials · doi:10.1021/acsaenm.2c00218 · Cited by 8
Lo, T., & Yu, S. (2021) · Macromolecular Materials and Engineering · doi:10.1002/mame.202100615 · Cited by 8
Bio-inspired tubular hierarchical porous materials with selective liquids absorption
Li, G., Dong, X., Chuan, A. R., Chua, B. W., Li, T., & Zhai, W. (2022) · Virtual and Physical Prototyping · doi:10.1080/17452759.2022.2129395 · Cited by 8
“The rest of the steps were the same as the single-nozzle DIW process (Hinton et al. 2016) using a commercial DIW machine (Allevi, USA).”
MethodOsmani, B., Gerganova, G., & Müller, B. (2017) · European Journal of Nanomedicine · doi:10.1515/ejnm-2017-0002 · Cited by 8
“Therefore, both the amplitude A and the periodicity λ are similarly influenced, as described by means of Equations (1) and (2).”
Izard, A. G., Pérez, L. X. P., Weisgraber, T. H., Meerbeek, I. M. V., Golobic, A. M., Duoss, E. B., & Lenhardt, J. M. (2024) · Advanced Materials Technologies · doi:10.1002/admt.202400423 · Cited by 7
Microfluidics, organs-on-a-chip, and 3D printing
Shah, M., Prakashan, D., & Gandhi, S. (2024) · Elsevier eBooks · doi:10.1016/b978-0-443-13782-2.00008-5 · Cited by 7
Biomechanical and mechanobiological design for bioprinting functional microvasculature
Zhang, D., Liu, J., Liu, X., & Fan, Y. (2025) · Applied Physics Reviews · doi:10.1063/5.0227692 · Cited by 7
Taherkhani, B., Rahmani, S., & Atalay, Ö. (2023) · Proceedings of the Institution of Mechanical Engineers Part L Journal of Materials Design and Applications · doi:10.1177/14644207231174325 · Cited by 7
Chansoda, K., Suvanjumrat, C., Wiroonpochit, P., Kaewprakob, T., & Chookaew, W. (2024) · Cleaner Materials · doi:10.1016/j.clema.2024.100257 · Cited by 7
Mohol, S. S., & Pandey, P. M. (2024) · Polymer · doi:10.1016/j.polymer.2024.127635 · Cited by 7
Human Septal Cartilage Tissue Engineering: Current Methodologies and Future Directions
Pham, T. B., Sah, R. L., Masuda, K., & Watson, D. J. (2024) · Bioengineering · doi:10.3390/bioengineering11111123 · Cited by 7
Macroporous Silicone Sheets Integrated with Meshes for Various Applications
Hayase, G., & Nomura, S. M. (2019) · ACS Applied Polymer Materials · doi:10.1021/acsapm.9b00382 · Cited by 7
Xiong, S., Chen, Y., Jia, W., Yang, X., Liu, K., Li, C., & Ling, G. (2021) · Journal of Micromechanics and Microengineering · doi:10.1088/1361-6439/abe09a · Cited by 7
Liu, S., Wu, J., He, S., Yang, B., Su, B., Yuan, X., & Wang, Y. (2023) · Composite Structures · doi:10.1016/j.compstruct.2023.117791 · Cited by 7
Cadle, R., Rogozea, D., Moldovan, L., Parsons‐Wingerter, P. A., & Moldovan, N. I. (2021) · Bioprinting · doi:10.1016/j.bprint.2021.e00152 · Cited by 7
A Hybrid Method for Additive Manufacturing of Silicone Structures
Liravi, F., Jacob-John, V., Toyserkani, A., & Vlasea, M. (2017) · doi:10.26153/16914 · Cited by 7
Wu, S., Wang, Z., Cai, Y., Chen, Y., Xian, Z., Luo, Y., You, H., & Sun, C. (2024) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2024.07.030 · Cited by 6
3D printing two-component liquid silicone rubber via direct ink writing
Ji, D., Wang, Z., & Xia, H. (2025) · Polymer · doi:10.1016/j.polymer.2025.129275 · Cited by 6
Design and Characterization of Viscoelastic McKibben Actuators with Tunable Force-Velocity Curves
Bennington, M. J., Wang, T., Yin, J., Bergbreiter, S., Majidi, C., & Webster‐Wood, V. A. (2023) · IEEE International Conference on Soft Robotics (RoboSoft) · doi:10.1109/robosoft55895.2023.10122014 · Cited by 6
“The Carbopol gel used in this project was adapted from [23].”
MethodAdditive manufacturing of silicone for biomedical applications
de Beer, D. J., Dzogbewu, T. C., & van der Walt, J. (2025) · Biomedical Engineering Advances · doi:10.1016/j.bea.2025.100158 · Cited by 6
Duraivel, S., Subramaniam, V., Chisolm, S. J., Scheutz, G. M., Sumerlin, B. S., Bhattacharjee, T., & Angelini, T. E. (2022) · Biophysics Reviews · doi:10.1063/5.0087387 · Cited by 6
Various Applications of 3D-Bioprinted Tissues/Organs Using Tissue-Specific Bioinks
Cho, D., Kim, B. S., Jang, J., Gao, G., Han, W., & Singh, N. K. (2019) · Springer eBooks · doi:10.1007/978-3-030-32222-9_7 · Cited by 6
Xu, T., Lim, Y. J., Zheng, Y., Jung, M., Gaus, K., Gardiner, E. E., & Lee, W. M. (2020) · Lab on a Chip · doi:10.1039/d0lc00598c · Cited by 6
Salam, M. A. R. B. A., Ridoy, A. H., Haque, A. K. M. A., Rafique, M. S., Hossain, M. A., Forhad, M. S., Boebinger, M. G., Ahmed, F., Schwab, K. R., Ferdous, S. F., et al. (2025) · Materials Today Communications · doi:10.1016/j.mtcomm.2025.114461 · Cited by 5
Fabrication of 3D microfluidic structure with direct selective laser baking of PDMS
Riahi, M., Karimi, F., & Ghaffari, A. (2019) · Rapid Prototyping Journal · doi:10.1108/rpj-01-2018-0021 · Cited by 5
Silicone 3D Printing Processes for Fabricating Synthetic, Self-Oscillating Vocal Fold Models
Greenwood, T. E. (2020) · ScholarsArchive (Brigham Young University) · Cited by 5
Engineering Dynamic 3D Models of Lung
Blomberg, R., Hewawasam, R. S., Šerbedžija, P., Saleh, K. S., Caracena, T., & Magin, C. M. (2023) · Advances in experimental medicine and biology · doi:10.1007/978-3-031-26625-6_9 · Cited by 5
Simulated inter-filament fusion in embedded 3D printing
Friedrich, L. M., & Gunther, R. T. (2024) · Biofabrication · doi:10.1088/1758-5090/ad8fd5 · Cited by 5
Using 3-D Printing and Bioprinting Technologies for Personalized Implants
Barthès, J., Courtial, E., Brenet, E., Muller, C. B., Knopf‐Marques, H., Marquette, C. A., & Vrana, N. E. (2019) · Elsevier eBooks · doi:10.1016/b978-0-12-816390-0.00014-5 · Cited by 5
Curing inhibition and shelf stability in silicone formulations for direct ink writing
Xie, F., Ghanbari, L. N., Maiti, A., Kaseman, D. C., Alexopoulos, A., Lenhardt, J. M., & Ford, M. J. (2025) · MRS Communications · doi:10.1557/s43579-025-00734-9 · Cited by 4
3D Printing of Interconnection-Tunable Porous Ink
Kim, W.-G., Kang, M., & Lim, J. (2025) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.5c10388 · Cited by 4
Sun, L., Cai, W., Zhang, Y., Zhang, Y., Jiang, Z., Qin, M., & Cui, Q. (2025) · Advanced Materials Technologies · doi:10.1002/admt.202502312 · Cited by 4
“Generally, sequentially printed extruded filaments do not lat-erally bond as expected [ 224, 230 ].”
Shape Memory Soft Robotics with Yield Stress Fluids
Wilt, J. K., Overvelde, J. T. B., & Coulais, C. (2023) · Advanced Intelligent Systems · doi:10.1002/aisy.202200332 · Cited by 4
Research on Embedded 3D Printing for Magnetic Soft Robots
Zhang, W., Li, J., Liu, H., & Jin, G. (2021) · IEEE International Conference on Nano/Micro Engineered and Molecular Systems · doi:10.1109/nems51815.2021.9451436 · Cited by 4
“cn) University demonstrated the freeform reversible embedding of PDMS material, which broadened the range of materials that can be applied to additive manufacturing [12].”
BackgroundHansen, C. J., Peterson, A. M., & Park, J. (2022) · Elsevier eBooks · doi:10.1016/b978-0-12-821632-3.00017-8 · Cited by 4
Hanim, M. A. A., Tahir, S. M., Jung, D., & Calin, R. (2021) · Elsevier eBooks · doi:10.1016/b978-0-12-822291-1.00015-4 · Cited by 4
3D Printing of Multifunctional Chitosan-Based Hydrogels and Nanocomposites
Wu, Q. (2018) · PolyPublie (École Polytechnique de Montréal) · Cited by 4
Printing silicone hollow structures in a bath of hydrogel
Henrichs, N. N., Sehrt, J. T., Brinkmann, T., & Berger, D. M. (2025) · Progress in Additive Manufacturing · doi:10.1007/s40964-025-01122-4 · Cited by 3
“By producing the RTV silicones in the hydrogel, which consists largely of water, complex structures such as helixes, grids, etc. can be produced with unlimited freedom from overhangs [16].”
Yao, X., Jiang, Y., Tian, L., Li, X., & He, Y. (2025) · Materials & Design · doi:10.1016/j.matdes.2025.114284 · Cited by 3
From 3D particle structuring to the 3D printing of silicones: A review
Kang, C., Oh, R., Han, D., Ko, Y., & Roh, S. (2025) · Korea-Australia Rheology Journal · doi:10.1007/s13367-025-00139-z · Cited by 3
Bougzime, O., Cruz, C., Zhou, K., Qi, H. J., & Demoly, F. (2026) · Computers in Industry · doi:10.1016/j.compind.2026.104522 · Cited by 4
Can Elastomers Combine Stiffness, Toughness and Fatigue Resistance?
Baur, E., & Amstad, E. (2026) · Advanced Materials · doi:10.1002/adma.74087 · Cited by 3
Design and Fabrication of a Sensorized Soft Actuator via Embedded 3D Printing
Chen, Y., Wu, Z., & Zhong, Y. (2022) · International Conference on Intelligent Robotics and Control Engineering (IRCE) · doi:10.1109/irce55557.2022.9963081 · Cited by 3
“As an extrusion-based 3D printing technology, EMB3D printing is able to fabricate complex soft structures directly by extruding ink into a fluid support matrix that can maintain the geometry of prints until they are taken out from the matrix after curing [22, 23].”
MethodResearch Progress of 3D Printing Silicone Rubber Materials
Li, Y., Hu, K., Xu, Y., Pei, Y., Yang, Z., Han, L., Li, L., & Wei, Y. (2024) · Lecture notes in electrical engineering · doi:10.1007/978-981-99-9955-2_16 · Cited by 3
Periyasamy, M., Campbell, R., Mead, J., Kazmer, D. O., Banerjee, S., Mubasshir, A., Phaen, L. A., & Kodra, S. (2024) · Micromachines · doi:10.3390/mi15050582 · Cited by 3
EXPECT: A thermosensitive embedded bioprinting platform for guided spatial cell organization
Pylostomou, A., Wychowaniec, J. K., Tognato, R., Egger, S. T., Alig, G. U., Edwards‐Gayle, C. J. C., Safari, F., Weiser, J. R., Loča, D., D’Este, M., et al. (2025) · Smart Materials in Medicine · doi:10.1016/j.smaim.2025.09.002 · Cited by 3
3D-Printed Pneumatic Microfluidic Mixer for Colorimetric Detection of Listeria monocytogenes
Yao, P., Wang, R., Xi, X., Li, Y., & Tung, S. C. H. (2019) · Transactions of the ASABE · doi:10.13031/trans.13245 · Cited by 3
Numerical studies on origami dielectric elastomer actuator using Kresling pattern
Kim, D., Park, J. H., Sikulskyi, S., Divo, E., & Martínez, R. (2019) · Electroactive Polymer Actuators, Sensors, and Devices (EAPAD) · doi:10.1117/12.2514374 · Cited by 3
In Situ Digital Image Analysis in Direct Ink Writing
Friedrich, L. M., & Begley, M. R. (2019) · ACS symposium series · doi:10.1021/bk-2019-1315.ch008 · Cited by 3
Aplicaciones biomédicas actuales de la impresión 3D y fabricación aditiva
Rodríguez‐Hernández, J., & Reinecke, H. (2020) · DIGITAL.CSIC (Spanish National Research Council (CSIC)) · Cited by 3
Recent advances in the extrusion methods for ceramics
Buj-Corral, I., Vidal, D., Tejo‐Otero, A., Fenollosa-Artés, F., Mesbahi, J. E., & Mesbahi, A. E. (2021) · IOP Conference Series Materials Science and Engineering · doi:10.1088/1757-899x/1193/1/012030 · Cited by 3
Gravity-Drawn Silicone Filaments: Production, Characterization, and Wormlike Chain Dynamics
Kiessling, R., Rubin, S. J. S., Zehner, J., Barraugh, C., Snell, K., Fukushima, C., Mulligan, M., Keckley, M., Bosshardt, A., Cook, W., et al. (2017) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.7b11972 · Cited by 3
Three-dimensional printing in hydrogel for a complex waveguiding photothermal microactuator
Yao, J., Li, R., Fang, Y., Tian, Z., Zhang, Q., Ding, D., Liu, J., & Yan, J. (2021) · OSA Continuum · doi:10.1364/osac.418590 · Cited by 3
Tan, E. Y. S. (2019) · DR-NTU (Nanyang Technological University) · doi:10.32657/10356/105573 · Cited by 3
Tejo‐Otero, A. (2021) · UPCommons institutional repository (Universitat Politècnica de Catalunya) · doi:10.5821/dissertation-2117-414264 · Cited by 3
Rahimnejad, M. (2022) · Papyrus : Institutional Repository (Université de Montréal) · doi:10.71781/27944 · Cited by 3
Shi, W., Gao, M., Zhou, X., Sun, X., Ding, H., Zhou, Y., Li, S., Sun, J., Gao, X., Liu, X., et al. (2026) · International Journal of Extreme Manufacturing · doi:10.1088/2631-7990/ae37ad · Cited by 2
“In the latter method, Hinton et al. [41] used a commercially available ME printer to print PDMS resin within a hydrophilic carbopol gel support bath.”
From lines to lattices—high-resolution 2D and 3D PDMS microarchitectures via aerosol jet printing
Kushagr, S., Hu, C., Yuan, B., Patel, D. K., Nandakumar, A., Narayan, R. L., & Panat, R. P. (2026) · npj Advanced Manufacturing · doi:10.1038/s44334-026-00080-1 · Cited by 2
Kim, H. R., Kim, Y., Yoo, B., Yoon, S., & Kim, S.-B. (2021) · Progress in Additive Manufacturing · doi:10.1007/s40964-021-00231-0 · Cited by 2
Yamashita, T., & Muramoto, T. (2022) · Analytical Sciences · doi:10.1007/s44211-022-00070-1 · Cited by 2
Study of Recyclable and Repairable Dynamic Covalent Polymers for Sustainable 3D Printing Development
Zheng, M. (2021) · Scholarship@Western (Western University) · Cited by 2
PDMS‐Supported Composite Materials as Oil Absorbent
Salman, N. A. S., Shahadat, M., Razali, M. R., & Adnan, R. (2022) · Wiley eBooks · doi:10.1002/9781119852322.ch9 · Cited by 2
Advances, Risks, and Challenges of 3D Bioprinting
Padhy, C. P., Amin, M., Sundaram, S., & Paul, P. (2024) · Wiley eBooks · doi:10.1002/9781394175109.ch3 · Cited by 2
Synthesis and functionalization methods of polymer nanocomposites for additive manufacturing
Ahmed, W. K., Mohammad, A. F., Zaneldin, E. K., Al-Marzouqi, A. H., & Al-Mazrouei, N. (2025) · Elsevier eBooks · doi:10.1016/b978-0-443-26516-7.00008-0 · Cited by 2
Materials for 3D Printing Cardiovascular Devices
Robinson, S. S., Kaboodrangi, A. H., Dunham, S. N., & Shepherd, R. F. (2018) · Elsevier eBooks · doi:10.1016/b978-0-12-803917-5.00003-1 · Cited by 2
Holness, F. B., Poepping, T. L., & Price, A. D. (2019) · Electroactive Polymer Actuators, Sensors, and Devices (EAPAD) · doi:10.1117/12.2514379 · Cited by 2
Microextrusion 3D Printing of Optical Waveguides and Microheaters
Udofia, E. N. (2019) · Journal of the Arkansas Academy of Science · Cited by 2
Konzepte für die Additive Fertigung optischer Elemente mit hochtransparenten Silikonwerkstoffen
Biermann, T., Ley, P.-P., Ziebehl, A., Feldmann, J., & Lachmayer, R. (2021) · Springer eBooks · doi:10.1007/978-3-662-63030-3_11 · Cited by 2
Extrusion 3D-printing of functional polymers
Nadgorny, M. (2018) · Minerva Access (University of Melbourne) · Cited by 2
3D PRINTING OF IRON OXIDE INCORPORATED POLYDIMETHYLSILOXANE SOFT MAGNETIC ACTUATOR
Bayaniahangar, R. (2020) · Digital Commons - Michigan Tech (Michigan Technological University) · doi:10.37099/mtu.dc.etdr/1016 · Cited by 2
“Although other studies attempted fabrication of helical coil structures using a similar mechanism, they failed to achieve fabricating free-standing coils.[37, 38, 42] While some”
ResultŚliwiak, M. (2018) · MacSphere (McMaster University) · doi:10.71548/8618 · Cited by 2
Uysal, E. (2021) · Dspace Repository (Marmara Üniversitesi) · Cited by 2
The first magnetic resonance imaging compatible 3D printer
Antoniou, A., Evripidou, N., Giannakou, M., & Damianou, C. (2024) · Digital Medicine · doi:10.1097/dm-2024-00006 · Cited by 1
Binder injection additive manufacturing
Brooks, H., Chadwick, S., Riding, A., & Saundry, C. (2025) · Rapid Prototyping Journal · doi:10.1108/rpj-01-2025-0037 · Cited by 1
Proximal sound printing: direct 3D printing of microstructures on polymers
Foroughi, S., Habibi, M., & Packirisamy, M. (2026) · Microsystems & Nanoengineering · doi:10.1038/s41378-025-01035-w · Cited by 1
“Printing heat-curing thermosets by incorporating a heat source is limited to approaches that utilize supporting medium 20 – 23 , frontal polymerization 24,25 , or rheological modi fi cation 26 – 29 .”
Ghighină, E., Dinu, A. I., & Ghițman, J. (2026) · Advanced Healthcare Materials · doi:10.1002/adhm.71319 · Cited by 1
“Hinton et al. [114] later demonstrated 3D printing of otherwise challenging materials like polydimethylsiloxane within Carbopol microgels into a cylindrical structure, while a concentration of 0.8% (w/v) Carbopol at neutral pH was identified as optimal for printing alginate [115].”
Influential
Metadata
- Authors
- Hinton, T. J., Hudson, A., Pusch, K., Lee, A., & Feinberg, A. W.
- Affiliations
- Carnegie Mellon University (US)
- Corresponding author
- Feinberg, Adam W.
- Venue
- ACS Biomaterials Science & Engineering
- Publisher
- American Chemical Society (ACS)
- Published
- 2016-05-04
- Volume
- 2
- Issue
- 10
- Pages
- 1781-1786
- ISSN
- 2373-9878 (ISSN-L)
- PMC
- PMC5059754
- OpenAlex
- W2345451752
- Cited by
- 437
- References
- 16
- Citations by year
- 2026: 22 · 2025: 32 · 2024: 44 · 2023: 46 · 2022: 50 · 2021: 68 · 2020: 63 · 2019: 46 · 2018: 41 · 2017: 24 · 2016: 1
- FWCI
- 17.97
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Locations
- ACS Biomaterials Science & Engineering (publishedVersion, cc-by)
- Europe PMC (PubMed Central) (publishedVersion)
- PubMed Central (publishedVersion)
- PubMed (publishedVersion)
- Funders
- U.S. Department of Health and Human Services (DP2HL117750)
- National Science Foundation (1454248)
- Disruptive Health Technology Institute, Carnegie Mellon University (A017261-HIGHMARK-Feinberg)
- Topics
- Physical Sciences › Engineering › Biomedical Engineering › 3D Printing in Biomedical Research
- Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Additive Manufacturing and 3D Printing Technologies
- Physical Sciences › Engineering › Biomedical Engineering › Microfluidic and Capillary Electrophoresis Applications
- Keywords
- support removal, phosphate buffered saline, helical filaments, microfluidics
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.