CoChat

Three-Dimensional Printed MoS2/Graphene Aerogel Electrodes for Hydrogen Evolution Reactions

Open access

The DOI matches its Crossref record; 48 of the 48 references it cites were found in a registry or an index; 4 of the 14 sources its claims cite were checked for support.

Abstract

High Resolution Image Download MS PowerPoint Slide In this work, we demonstrate the use of direct ink writing (DIW) technology to create 3D catalytic electrodes for electrochemical applications. Hybrid MoS 2 /graphene aerogels are made by mixing commercially available MoS 2 and graphene oxide powders into a thixotropic, high concentration, viscous ink. A porous 3D structure of 2D graphene sheets and MoS 2 particles was created after post treatment by freeze-drying and reducing graphene oxide through annealing. The composition and morphology of the samples were fully characterized through XPS, BET, and SEM/EDS. The resulting 3D printed MoS 2 /graphene aerogel electrodes had a remarkable electrochemically active surface area (>1700 cm 2 ) and were able to achieve currents over 100 mA in acidic media. Notably, the catalytic activity of the MoS 2 /graphene aerogel electrodes was maintained with minimal loss in surface area compared to the non-3D printed electrodes, suggesting that DIW can be a viable method of producing durable electrodes with a high surface area for water splitting. This demonstrates that 3D printing a MoS 2 /graphene 3D porous network directly using our approach not only improves electrolyte dispersion and facilitates catalyst utilization but also provides multidimensional electron transport channels for improving electronic conductivity.

Overview

CoChat Summary

TL;DR

Direct ink writing was used to 3D print hybrid MoS₂/graphene aerogel electrodes for the hydrogen evolution reaction. The printed lattices achieved high electrochemically active surface area and maintained it under high currents, while monoliths lost substantial ECSA due to trapped H₂ gas.

Key findings

  • 3D printed GA/MoS₂ lattices and monoliths had ECSAs of ∼1725 and ∼3100 cm², respectively, compared with ∼800 and ∼1540 cm² for graphene-only control lattices and monoliths.
  • GA/MoS₂ electrodes showed improved HER activity over GA controls and achieved over 100 mA total current in 0.5 M sulfuric acid.
  • After 1 h chronopotentiometry at 10, 50, and 100 mA, GA/MoS₂ lattices lost <2% of their ECSA, whereas GA/MoS₂ and GA monoliths lost >60% due to H₂ gas trapped in pores.
  • The aerogels had a surface area of 89 m²/g, greater than a similarly made graphene aerogel (26 m²/g) but lower than previous GA/MoS₂ aerogels (691 m²/g) because freeze-drying was used instead of critical point drying.

Methods

  • Ink was formulated with 4 wt % graphene oxide (300–800 nm platelets), 4 wt % commercial MoS₂, and hydroxypropyl methyl cellulose; cubic lattices and monoliths were printed by DIW, freeze-dried for 48 h, and annealed at 1050 °C for 3 h under 4% H₂/Ar with excess sulfur.
  • Composition and morphology were characterized by XPS, BET nitrogen porosimetry, and SEM/EDS.
  • Electrochemical testing used cyclic voltammetry for ECSA in a non-Faradaic window at 50–200 mV/s, HER CV in 0.5 M H₂SO₄ with an iridium oxide on carbon anode and Nafion membrane, and chronopotentiometry at 10, 50, and 100 mA for 1 h with gas chromatography for H₂ quantification.

Limitations

  • The paper states that freeze-drying produced a lower surface area (89 m²/g) than previous critical point-dried GA/MoS₂ aerogels (691 m²/g).
  • The paper reports that monolith structures lost >60% ECSA after chronopotentiometry because H₂ gas became trapped in pores, blocking electrolyte access.
  • Evident from the text: no explicit limitations section is provided, and durability testing was limited to 1 h chronopotentiometry at three currents; detailed ink preparation and printing are relegated to Supporting Information.

Model-written summary. Check it against the paper before relying on it.

Integrity signals

Registry

Crossref · 10.1021/acsmaterialsau.2c00014

Cites

48 of 48 references verified0 citation errors · 0 not checkable

Statistics

Nothing to recompute.

Figures

Figure 1 (a–c) DIW of GO/MoS2 with rheological studies.
Figure 1 (a–c) DIW of GO/MoS2 with rheological studies.CC BY-NC-ND · PubMed Central
Figure 2 (a, b) Scanning electron micrographs of a 3D printed graphene/MoS2 aerogel (inset scale bar: 5 mm) and (c-i–iv) elemental image analysis of the GA/MoS2 aerogel.
Figure 2 (a, b) Scanning electron micrographs of a 3D printed graphene/MoS2 aerogel (inset scale bar: 5 mm) and (c-i–iv) elemental image analysis of the GA/MoS2 aerogel.CC BY-NC-ND · PubMed Central
Figure 3 (a) Nitrogen adsorption–desorption isotherms and (b) BJH pore size distribution derived from the desorption isotherms of GA/MoS2.
Figure 3 (a) Nitrogen adsorption–desorption isotherms and (b) BJH pore size distribution derived from the desorption isotherms of GA/MoS2.CC BY-NC-ND · PubMed Central
Figure 4 Electrochemical results from testing the 3D printed electrodes. (a) ECSA of the 3D printed GA/MoS2 lattice. (b) CV curves of samples on a current density basis. (c) CP of the GA/MoS2 lattice at 10, 50, and 100 mA showing stability over 1 h.
Figure 4 Electrochemical results from testing the 3D printed electrodes. (a) ECSA of the 3D printed GA/MoS2 lattice. (b) CV curves of samples on a current density basis. (c) CP of the GA/MoS2 lattice at 10, 50, and 100 mA showing stability over 1 h.CC BY-NC-ND · PubMed Central

Verification

Claims the paper makes

2 Valid · 3 Not valid · 5 Not checked · 31 Own results and interpretations

19 more claims

Create a free account to see all 41 claims and to verify the 1 reference still open.

See all claims — free account
  • It may state two separate claims as one. 13
  • Probably not a substantial claim. 6
  • Borderline: one of the tests for a substantial claim is unclear. 1

Create a free account to see these claims.

Citations

Cites

Show all 48 references

Cited by

Metadata

Authors
Chandrasekaran, S., Feaster, J., Ynzunza, J., Li, F., Wang, X., Nelson, A. J., & Worsley, M. A.
Affiliations
Lawrence Livermore National Laboratory (US)
Corresponding author
  • Chandrasekaran, Swetha
  • Worsley, Marcus A.
Venue
ACS Materials Au
Published
2022-05-05
Volume
2
Issue
5
Pages
596-601
ISSN
2694-2461 (ISSN-L)
OpenAlex
W4229023228
Cited by
38
References
48
Citations by year
2026: 9 · 2025: 6 · 2024: 9 · 2023: 12 · 2022: 2
FWCI
1.31
Type
journal article
Language
en
Open access
Locations
  • ACS Materials Au (publishedVersion, cc-by-nc-nd)
  • PubMed Central (publishedVersion, cc-by-nc-nd)
  • PubMed (publishedVersion)
  • OSTI OAI (U.S. Department of Energy Office of Scientific and Technical Information) (submittedVersion)
Funders
U.S. Department of Energy (DE-AC52-07NA27344)
Topics
  • Physical Sciences › Energy › Renewable Energy, Sustainability and the Environment › Electrocatalysts for Energy Conversion
  • Physical Sciences › Materials Science › Electronic, Optical and Magnetic Materials › Supercapacitor Materials and Fabrication
  • Physical Sciences › Engineering › Electrical and Electronic Engineering › Fuel Cells and Related Materials
Keywords
direct ink writing, 3D-printed electrodes, hydrogen evolution reaction, electrocatalysis, water splitting, graphene oxide reduction, freeze-drying, electrochemically active surface area, catalyst utilization, electronic conductivity

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

The claim verdicts this report counts are experimental: their accuracy is not yet measured.

A language model drew the claims from the paper on 2026-10-11, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).

A second model labelled each claim on 2026-10-11 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.