Shape-Memory Polymer Nanocomposites of Poly(ε-caprolactone) with the Polystyrene-block-polybutadiene-block-polystyrene-tri-block Copolymer Encapsulated with Metal Oxides
Open accessThe DOI matches its Crossref record; 74 of the 76 references it cites were found in a registry or an index, and 1 are not checked yet; 4 of the 32 sources its claims cite were checked for support.
Abstract
Shape-memory polymer composite blends derived from PCL and SBS were characterized for morphological, thermal, mechanical, and shape-memory properties; addition of nano-metal-oxide fillers improved overall properties and the work developed a microvalve actuator system.
Verified 2026-11-19 · 1 reference not checked yet
Overview
CoChat Summary
TL;DR
The paper reports thermo-responsive shape-memory polymer composites (SMPCs) made from poly(ε-caprolactone) (PCL) and polystyrene-block-polybutadiene-block-polystyrene (SBS) with CuO, Fe2O3, or CuFe2O4 nanofillers. SMPC–Fe2O3 showed the best overall thermal, mechanical, and shape-memory performance, and was used to demonstrate a microvalve actuator.
Key findings
- SMP and SMPCs were prepared from equal SBS/PCL ratios with 0.2 parts metal-oxide filler; the fillers improved overall properties, and SMPC–CuFe2O4 had the highest tensile modulus and was very rigid/brittle, while neat SMP was more elastic with low Young’s modulus.
- Shape recovery ratio (Rr) was high and equal for SMPC–Fe2O3 and SMPC–CuO at 91.6%, with the order SMPC–Fe2O3 ≥ SMPC–CuO > SMP > SMPC–CuFe2O4; shape fixing increased as SMPC–CuO > SMPC–Fe2O3 > SMP > SMPC–CuFe2O4.
- SMPC–Fe2O3 showed the better thermal, mechanical, and shape-memory performances and attained the optimum storage modulus among the SMPCs; a microvalve actuator system was demonstrated using SMPC–Fe2O3.
- DSC showed Tm at 63 °C for SMP and 64 °C for metal-oxide-reinforced SMPCs; the paper reports Tg above −70 °C and crystallization temperature at 40 °C.
Methods
- Composites were synthesized by melt blending SBS, PCL, and nano-metal-oxide fillers in a Hakke mixer at 180 °C and 60 rpm for 7 min, then hot-pressed at 180 °C and 5 kg N/m² to 2.5 mm films.
- Characterization included FT-IR, UV–vis, XRD, TGA/DTG coupled with GC–MS, DSC, POM, SEM, AFM, tensile testing, DMA, and thermo-active shape-memory testing by the fold-deploy method.
- Tensile and shape-memory plots report standard deviation with n = 5; DMA used rectangular specimens 60 mm × 4 mm × 2 mm at 1 Hz from −100 to +100 °C; shape-memory samples were 100 × 10 × 3 mm.
Limitations
- The paper does not state limitations.
- Evident from the text: some morphological and thermal data are referenced to supplementary Figures S1 and S2, which are not included in the provided text.
- Evident from the text: the actuator demonstration is qualitative, and the paper reports no cycling/fatigue or long-term stability testing for the shape-memory composites.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures















Verification
Claims the paper makes
3 Valid · 0 Not valid · 11 Not checked · 85 Own results and interpretations
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“All major decompositions and evolutions of gases occurred at a temperature between 350 and 550 °C.”
§ Shape-Memory Polymer Nanocomposites of Poly(ε-caprolactone) with the Polystyrene-block-polybutadiene-block-polystyrene-tri-block Copolymer Encapsulated with Metal Oxides > Results and Discussion
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The water loss is found to be higher in neat SMP and decreases as follows: SMP > SMPC–CuO > SMPC–Fe2O3 > SMPC–CuFe2O4.”
§ Shape-Memory Polymer Nanocomposites of Poly(ε-caprolactone) with the Polystyrene-block-polybutadiene-block-polystyrene-tri-block Copolymer Encapsulated with Metal Oxides > Results and Discussion
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
In the paper
“The results show that polymeric SMPCs have undergone thermal degradation in two different stages.64”
§ Shape-Memory Polymer Nanocomposites of Poly(ε-caprolactone) with the Polystyrene-block-polybutadiene-block-polystyrene-tri-block Copolymer Encapsulated with Metal Oxides > Results and Discussion
What the sources say
- Not checked — no full text of the sourcecites [64] source
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Water loss is also observed between the temperature of 350 and 550 °C, which is also evident in all prepared samples, due to dehydroxylation in SBS and PCL layers.”
§ Shape-Memory Polymer Nanocomposites of Poly(ε-caprolactone) with the Polystyrene-block-polybutadiene-block-polystyrene-tri-block Copolymer Encapsulated with Metal Oxides > Results and Discussion
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Generally, the uncompatibilized blend exhibited a higher storage modulus than the compatibilized blend and blend composites.”
§ Shape-Memory Polymer Nanocomposites of Poly(ε-caprolactone) with the Polystyrene-block-polybutadiene-block-polystyrene-tri-block Copolymer Encapsulated with Metal Oxides > Results and Discussion
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
52 more claims
Create a free account to see all 99 claims and to verify the 1 reference still open.
- Probably not a substantial claim. 15
- It may state two separate claims as one. 30
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
§ Shape-Memory Polymer Nanocomposites of Poly(ε-caprolactone) with the Polystyrene-block-polybutadiene-block-polystyrene-tri-block Copolymer Encapsulated with Metal Oxides > Experimental Section > Materials
“(i) iron(II, III) oxide nanopowder with a 50–100 nm particle size”
§ Shape-Memory Polymer Nanocomposites of Poly(ε-caprolactone) with the Polystyrene-block-polybutadiene-block-polystyrene-tri-block Copolymer Encapsulated with Metal Oxides > Abstract
“encapsulated with CuO, Fe2O3, and CuFe2O4”
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
§ Shape-Memory Polymer Nanocomposites of Poly(ε-caprolactone) with the Polystyrene-block-polybutadiene-block-polystyrene-tri-block Copolymer Encapsulated with Metal Oxides > Results and Discussion
“For all SMPCs, the nanofiller reinforcement causes a decrease in the dynamic storage moduli over the investigated temperature range, when compared to the neat polymer, SMP.”
§ Shape-Memory Polymer Nanocomposites of Poly(ε-caprolactone) with the Polystyrene-block-polybutadiene-block-polystyrene-tri-block Copolymer Encapsulated with Metal Oxides > Results and Discussion
“The dynamic storage modulus decreases as follows: SMPC–CuFe2O4 > SMPC–Fe2O3 > SMPC–CuO > SMP.”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Shape-Memory Polymer Nanocomposites of Poly(ε-caprolactone) with the Polystyrene-block-polybutadiene-block-polystyrene-tri-block Copolymer Encapsulated with Metal Oxides > Experimental Section > Materials
“(iii) copper–iron oxide nanopowder, with a <100 nm particle size (BET)”
§ Shape-Memory Polymer Nanocomposites of Poly(ε-caprolactone) with the Polystyrene-block-polybutadiene-block-polystyrene-tri-block Copolymer Encapsulated with Metal Oxides > Abstract
“three metal oxide nanofillers encapsulated within the SMP matrix”
Citations
Cites
Kinetic Parameters from Thermogravimetric Data
COATS, A. W., & REDFERN, J. P. (1964) · Nature · doi:10.1038/201068a0 · Cited by 6,930
Lendlein, A., & Kelch, S. (2002) · Kirk-Othmer Encyclopedia of Chemical Technology · doi:10.1002/0471238961.1908011612051404.a01 · Cited by 2,566
Behl, M., & Lendlein, A. (2007) · Materials Today · doi:10.1016/s1369-7021(07)70047-0 · Cited by 1,965
Review of progress in shape-memory polymers
Liu, C., Qin, H., & Mather, P. T. (2007) · Journal of Materials Chemistry · doi:10.1039/b615954k · Cited by 1,942
Shape-memory polymers and their composites: stimulus methods and applications
Leng, J., Lan, X., Liu, Y., & Du, S. (2011) · Progress in Materials Science · doi:10.1016/j.pmatsci.2011.03.001 · Cited by 1,495
Tunable polymer multi-shape memory effect
Xie, T. (2010) · Nature · doi:10.1038/nature08863 · Cited by 1,380
Hu, J., Zhu, Y., Huang, H., & Lu, J. (2012) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2012.06.001 · Cited by 1,279
A review of stimuli-responsive shape memory polymer composites
Meng, H., & Li, G. (2013) · Polymer · doi:10.1016/j.polymer.2013.02.023 · Cited by 1,190
Koerner, H., Price, G., Pearce, N. A., Alexander, M., & Vaia, R. A. (2004) · Nature Materials · doi:10.1038/nmat1059 · Cited by 1,034
Shape memory polymers: Past, present and future developments
Hager, M. D., Bode, S., Weber, C., & Schubert, U. S. (2015) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2015.04.002 · Cited by 950
Research works printed but not linked: 2
- 10.1002/1521-3773(20020617)41:12<2034::aid-anie2034>3.0.co;2-m · doi:10.1002/1521-3773(20020617)41:12<2034::aid-anie2034>3.0.co;2-m
- Al-Humairi S. N., 2019, InSmart and Functional Soft Materials;, 23
Cited by
Maji, P., & Naskar, K. (2022) · Journal of Applied Polymer Science · doi:10.1002/app.52942 · Cited by 121
Recent trends in thermo‐responsive elastomeric shape memory polymer nanocomposites
Gopinath, S., Adarsh, N. N., Nair, P. R., & Mathew, S. (2023) · Polymer Composites · doi:10.1002/pc.27464 · Cited by 73
Self-citationŞenyurt, M. A., Kurdiş, M. M., Ulus, H., & Avcı, A. (2025) · Fibers and Polymers · doi:10.1007/s12221-025-00926-z · Cited by 51
Styrene‐butadiene‐styrene ‐based shape memory polymers: Evolution and the current state of art
Basak, S., & Bandyopadhyay, A. (2022) · Polymers for Advanced Technologies · doi:10.1002/pat.5682 · Cited by 34
Idumah, C. I. (2023) · Polymer Engineering and Science · doi:10.1002/pen.26331 · Cited by 29
Metadata
- Authors
- Gopinath, S., Adarsh, N. N., Nair, P. R., & Mathew, S.
- Affiliations
- Mahatma Gandhi University (IN)
- Corresponding author
- Mathew, Suresh
- Venue
- ACS Omega
- Publisher
- American Chemical Society (ACS)
- Published
- 2021-02-22
- Volume
- 6
- Issue
- 9
- Pages
- 6261-6273
- ISSN
- 2470-1343 (ISSN-L)
- PMC
- PMC7948221
- OpenAlex
- W3130479042
- Cited by
- 39
- References
- 76
- Citations by year
- 2026: 2 · 2025: 8 · 2024: 11 · 2023: 7 · 2022: 9 · 2021: 2
- FWCI
- 3.10
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- ACS Omega (publishedVersion, cc-by-nc-nd)
- PubMed Central (publishedVersion, cc-by-nc-nd)
- PubMed (publishedVersion)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Funders
- Mahatma Gandhi University
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Advanced Materials and Mechanics
- Physical Sciences › Materials Science › Polymers and Plastics › Polymer composites and self-healing
- Physical Sciences › Materials Science › Materials Chemistry › Block Copolymer Self-Assembly
- Keywords
- shape memory polymers, polycaprolactone, nanocomposites, triblock copolymers, microsystems
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.