CoChat

Integrated PbS Colloidal Quantum Dot Photodiodes on Silicon Nitride Waveguides

Open access

The DOI matches its Crossref record; 70 of the 72 references it cites were found in a registry or an index; 6 of the 41 sources its claims cite were checked for support.

Abstract

Colloidal quantum dots (QDs) have become a versatile optoelectronic material for emitting and detecting light that can overcome the limitations of a range of electronic and photonic technology platforms. Photonic integrated circuits (PICs), for example, face the persistent challenge of combining active materials with passive circuitry ideally suited for guiding light. Here, we demonstrate the integration of photodiodes (PDs) based on PbS QDs on silicon nitride waveguides (WG). Analyzing planar QDPDs first, we argue that the main limitation WG-coupled QDPDs face is detector saturation induced by the high optical power density of the guided light. Using the cladding thickness and waveguide width as design parameters, we mitigate this issue, and we demonstrate WG-QDPDs with an external quantum efficiency of 67.5% at 1275 nm that exhibit a linear photoresponse for input powers up to 400 nW. In the next step, we demonstrate a compact infrared spectrometer by integrating these WG-QDPDs on the output channels of an arrayed waveguide grating demultiplexer. This work provides a path toward a low-cost PD solution for PICs, which are attractive for large-scale production.

Overview

CoChat Summary

## TL;DR

The paper demonstrates the first integration of PbS colloidal quantum dot photodiodes on silicon nitride waveguides using standard fabrication techniques. By tuning waveguide width and cladding thickness, the authors achieved a waveguide-coupled device with 67.5% EQE at 1275 nm and linear response up to 400 nW, and used it to build an 8-channel on-chip infrared spectrometer.

## Key findings

  • Planar bottom-illuminated QDPDs showed a dark current of 70 nA at −1 V and an EQE of 16% at 0.12 mW total illumination power; their saturation power density was defined as 5.2 W/cm².
  • For WG-QDPDs, the best devices achieved an average EQE of 67.5% in the 6–60 nW range at 1275 nm, with a responsivity of 0.69 A/W and linear response up to 400 nW at −1 V.
  • The optimized waveguide-integrated design used a 30 μm waveguide width and 350 nm cladding thickness; the paper says this should yield a saturation power of up to 6.9 μW, with a modeled loss of 623 dB/cm, 95% absorption in a 200 μm-long device, and a maximally attainable EQE of 82%.
  • An integrated 8-channel AWG spectrometer covered a 51 nm wavelength range with 7.3 nm channel spacing and measured channel crosstalk better than 15 dB.

## Methods

  • The study combined planar bottom-illuminated QDPDs with waveguide-integrated QDPDs on a 300 nm SiN waveguide layer; the waveguide device stack used ZnO/Al2O3/PbS QD/Au layers.
  • Fabrication used standard microfabrication methods including PECVD SiN deposition, EBL, RIE, ALD of ZnO and Al2O3, photolithography, wet etching, and liftoff; QD films were patterned and assembled from PbS-PbI2 and PbS-EDT layers.
  • Devices were characterized with a Keithley 2450 source meter and an O-band tunable laser, measuring current-voltage curves, EQE, saturation behavior, and spectral response; waveguide power was calibrated using reference waveguides without QDPDs.

## Limitations

  • The paper states a trade-off between saturation threshold and dark current: increasing waveguide width or cladding thickness raises saturation power but requires longer detectors, which increases dark current.
  • The measured WG-QDPD saturation power of 400 nW was about 1 order of magnitude smaller than the predicted 6.9 μW, which the paper attributes to differences between the idealized simulation structure and the fabricated device, including possible contamination and defects.
  • Evident from the text: several claims about scalability and wafer-scale fabrication are prospective rather than demonstrated here, because the authors note that photolithography could be used and foundry-style integration could be possible, but this paper’s devices were fabricated with lab-processed waveguides and EBL.

Model-written summary. Check it against the paper before relying on it.

Integrity signals

Registry

Crossref · 10.1021/acsphotonics.3c00945

Cites

70 of 70 references verified0 citation errors · 0 not checkable

Statistics

Nothing to recompute.

Figures

Figure 1 Structure and characterization of BI-QDPD. (a) Device structure of the BI-QDPD, illuminated from the bottom glass side by laser with Gaussian beam shape. (b) Absorption spectra for both types of QDs used in the BI-QPDD, dispersed in n-octane. QDs with the exciton peak around 1300 nm were used for absorption, and QDs around 950 nm were used as hole-transport and electron-blocking materials. (c) Dark current and photocurrent of BI-QDPD with an area of 1.77 mm2. The photocurrent was measured for illumination at 1275 nm with a power of 0.16 mW (peak power density of ∼100 mW/cm2). (d) EQE of BI-QDPD vs optical power density at a bias voltage of −1 V. The intersection of the dashed lines indicates the onset of saturation. Inset: photocurrent vs optical maximum power density. The optical power density is measured in the center of the Gaussian beam illuminating the BI-QDPD.
Figure 1 Structure and characterization of BI-QDPD. (a) Device structure of the BI-QDPD, illuminated from the bottom glass side by laser with Gaussian beam shape. (b) Absorption spectra for both types of QDs used in the BI-QPDD, dispersed in n-octane. QDs with the exciton peak around 1300 nm were used for absorption, and QDs around 950 nm were used as hole-transport and electron-blocking materials. (c) Dark current and photocurrent of BI-QDPD with an area of 1.77 mm2. The photocurrent was measured for illumination at 1275 nm with a power of 0.16 mW (peak power density of ∼100 mW/cm2). (d) EQE of BI-QDPD vs optical power density at a bias voltage of −1 V. The intersection of the dashed lines indicates the onset of saturation. Inset: photocurrent vs optical maximum power density. The optical power density is measured in the center of the Gaussian beam illuminating the BI-QDPD.CC BY-NC-ND · PubMed Central
Figure 2 Design of WG-QDPD. (a) Device structure of WG-QDPD. (b) Link between saturation of BI-QDPD and WG-QDPD. Red arrows point out the light propagation direction, vertical for the BI-QDPD and horizontal for the WG-QDPD. The electrons and holes are extracted in the vertical direction for both cases. The PbS-PbI2 absorption layer can be split into small cells. The total carrier generation rate in each cell determines its local saturation. The cell with the maximum total carrier generation rate (indicated by a blue arrow) determines the onset of saturation for the whole PD. (c) Simulated saturation power of WG-QDPD vs cladding thickness and waveguide width. (d) Slice of (c) for a waveguide width of 30 μm. (e) Slice of (c) for a cladding thickness of 0.35 μm.
Figure 2 Design of WG-QDPD. (a) Device structure of WG-QDPD. (b) Link between saturation of BI-QDPD and WG-QDPD. Red arrows point out the light propagation direction, vertical for the BI-QDPD and horizontal for the WG-QDPD. The electrons and holes are extracted in the vertical direction for both cases. The PbS-PbI2 absorption layer can be split into small cells. The total carrier generation rate in each cell determines its local saturation. The cell with the maximum total carrier generation rate (indicated by a blue arrow) determines the onset of saturation for the whole PD. (c) Simulated saturation power of WG-QDPD vs cladding thickness and waveguide width. (d) Slice of (c) for a waveguide width of 30 μm. (e) Slice of (c) for a cladding thickness of 0.35 μm.CC BY-NC-ND · PubMed Central
Figure 3 Processing steps to fabricate WG-QDPD. (a) SiN waveguide patterning and top cladding deposition. (b) ALD of the ZnO electron transport layer and Al2O3 protection layer. (c) N-contact metal patterning with photoresist and liftoff. (d) QD film patterning with PMMA resist and liftoff. The Al2O3 protection layer was removed before spin-coating QDs. (e) P-contact metal patterning with PMMA resist and liftoff. (f) Top view of the fabricated WG-QDPD.
Figure 3 Processing steps to fabricate WG-QDPD. (a) SiN waveguide patterning and top cladding deposition. (b) ALD of the ZnO electron transport layer and Al2O3 protection layer. (c) N-contact metal patterning with photoresist and liftoff. (d) QD film patterning with PMMA resist and liftoff. The Al2O3 protection layer was removed before spin-coating QDs. (e) P-contact metal patterning with PMMA resist and liftoff. (f) Top view of the fabricated WG-QDPD.CC BY-NC-ND · PubMed Central
Figure 4 Response of WG-QDPDs. (a) I–V curves of WG-QDPDs under dark conditions and illumination at 1275 nm. (b) EQE vs optical power at −1 V bias voltage. Inset: photocurrent vs optical power with bias voltage of −1 V. The intersection of the black dashed lines indicates the onset of saturation. (c) Normalized EQE vs photocurrent at −2 V bias voltage for different waveguide widths. The saturation points of WG-QDPDs are indicated by vertical black dashed lines. (d) Saturation photocurrent with different waveguide widths. A linear fit is indicated by the black dashed line.
Figure 4 Response of WG-QDPDs. (a) I–V curves of WG-QDPDs under dark conditions and illumination at 1275 nm. (b) EQE vs optical power at −1 V bias voltage. Inset: photocurrent vs optical power with bias voltage of −1 V. The intersection of the black dashed lines indicates the onset of saturation. (c) Normalized EQE vs photocurrent at −2 V bias voltage for different waveguide widths. The saturation points of WG-QDPDs are indicated by vertical black dashed lines. (d) Saturation photocurrent with different waveguide widths. A linear fit is indicated by the black dashed line.CC BY-NC-ND · PubMed Central
Figure 5 Integrated spectrometer with a QDPD array and AWG. (a) Top view of the spectrometer. Light is injected from the right grating coupler. (b) Response of eight channels without applying bias voltage. The response of each channel was normalized to its maximum.
Figure 5 Integrated spectrometer with a QDPD array and AWG. (a) Top view of the spectrometer. Light is injected from the right grating coupler. (b) Response of eight channels without applying bias voltage. The response of each channel was normalized to its maximum.CC BY-NC-ND · PubMed Central

Verification

Claims the paper makes

1 Valid · 4 Not valid · 22 Not checked · 82 Own results and interpretations

64 more claims

Create a free account to see all 109 claims and to verify the 16 references still open.

See all claims — free account
  • It may state two separate claims as one. 25
  • Probably not a substantial claim. 22

Create a free account to see these claims.

Claims other papers make about this one

Each is checked against this paper’s own text: does it say what the citing paper says it does?

Citations

Cites

Show all 70 references

Cited by

See all 16

Metadata

Authors
Pang, C., Deng, Y.-H., Kheradmand, E., Poonkottil, N., Petit, R., Elsinger, L., Detavernier, C., Geiregat, P., Hens, Z., & Van Thourhout, D.
Affiliations
  • Ghent University (BE)
  • Photonics Research Group, Ghent University - imec, 9052 Ghent, Belgium
Venue
ACS Photonics
Published
2023-11-20
Volume
10
Issue
12
Pages
4215-4224
ISSN
2330-4022 (ISSN-L)
OpenAlex
W4388841251
Cited by
16
References
72
Citations by year
2026: 6 · 2025: 6 · 2024: 4
FWCI
1.13
Type
journal article
Language
en
Open access
Locations
  • ACS Photonics (publishedVersion, cc-by-nc-nd)
  • PubMed (publishedVersion)
  • Ghent University Academic Bibliography (Ghent University) (publishedVersion)
  • Ghent University Academic Bibliography (Ghent University) (submittedVersion, other-oa)
  • PubMed Central (submittedVersion, cc-by-nc-nd)
Funders
  • Fonds Wetenschappelijk Onderzoek (G0B2921N, G0C5723N)
  • China Scholarship Council (201906120023)
  • Bijzonder Onderzoeksfonds UGent (GOA01019)
  • H2020 European Research Council (884963)
Topics
  • Physical Sciences › Materials Science › Materials Chemistry › Quantum Dots Synthesis And Properties
  • Physical Sciences › Physics and Astronomy › Atomic and Molecular Physics, and Optics › Photonic Crystals and Applications
  • Physical Sciences › Engineering › Electrical and Electronic Engineering › Photonic and Optical Devices
Keywords
PbS colloidal quantum dots, silicon nitride waveguides, photonic integrated circuits, detector saturation, external quantum efficiency, infrared spectrometer

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

The claim verdicts this report counts are experimental: their accuracy is not yet measured.

A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).

A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).

Cited sources are checked with a language model’s help (qwen3.8-omni-flash and gpt-6-sol).

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Integrated PbS Colloidal Quantum Dot Photodiodes on Silicon Nitride Waveguides. https://app.cochat.ai/papers/10.1021/acsphotonics.3c00945
The paper
Pang, C., Deng, Y.-H., Kheradmand, E., Poonkottil, N., Petit, R., Elsinger, L., Detavernier, C., Geiregat, P., Hens, Z., & Van Thourhout, D. (2023). Integrated PbS Colloidal Quantum Dot Photodiodes on Silicon Nitride Waveguides. ACS Photonics. https://doi.org/10.1021/acsphotonics.3c00945

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.