The DOI matches its Crossref record; 59 of the 59 references it cites were found in a registry or an index; 18 of the 37 sources its claims cite were checked for support.
A silicon photonics waveguide-coupled colloidal quantum dot photodiode sensitive beyond 1.6 µ m
Open accessAbstract
Silicon photonics faces a persistent challenge in extending photodetection capabilities beyond the 1.6 µm wavelength range, primarily due to the lack of appropriate epitaxial materials. Colloidal quantum dots present a promising solution here, offering distinct advantages, such as infrared wavelength tunability, cost-effectiveness, and facile deposition. Their unique properties position them as a potential candidate for enabling photodetection in silicon photonics beyond the conventional telecom wavelength, thereby expanding the potential applications and capabilities within this domain. In this study, we have successfully integrated lead sulfide (PbS) colloidal quantum dot photodiodes (QDPDs) onto silicon waveguides using standard process techniques. The integrated photodiodes exhibit a remarkable responsivity of 1.3 A/W (with an external quantum efficiency of 74.8%) at a wavelength of 2.1 µm, a low dark current of only 106 nA, and a bandwidth of 1.1 MHz under a −3 V bias. To demonstrate the scalability of our integration approach, we have developed a compact 8-channel spectrometer incorporating an array of QDPDs. This achievement marks a significant step toward realizing a cost-effective photodetector solution for silicon photonics, particularly tailored for a wide range of sensing applications around the 2 µm wavelength range.
Overview
CoChat Summary
TL;DR
The paper demonstrates silicon-photonics waveguide-coupled PbS colloidal quantum dot photodiodes that detect beyond 1.6 μm, with measured operation at 2.1 μm. The integrated devices achieve 1.3 A/W responsivity, 106 nA dark current, and 1.1 MHz bandwidth, and are used to build a compact 8-channel on-chip spectrometer.
Key findings
- The optimized surface-illuminated QDPD stack (structure B) showed a 10-fold lower dark current than the initial stack, with 50.3 μA dark current at -3 V and 0.19 A/W responsivity at 2.1 μm for a 1.77 mm² device.
- The waveguide-coupled QDPD (WG-QDPD) exhibited 106 nA dark current at -3 V and 1.3 A/W responsivity at 2.1 μm, corresponding to 74.8% external quantum efficiency.
- The WG-QDPD bandwidth was 1.1 MHz; the paper estimates an RC-limited bandwidth of 388 MHz and argues the measured speed is likely drift-limited.
- A compact integrated spectrometer with 8 WG-QDPDs covered 2063 to 2135 nm, with crosstalk better than -20 dB and insertion loss less than 3 dB.
Methods
- The study first optimized PbS QDPD layer stacks on glass-ITO using surface illumination, then integrated the chosen stack onto 220 nm SOI waveguides with 2 μm buried oxide using standard fabrication steps (EBL, etching, sputtering, spin coating, wet etching, and metal lift-off).
- The waveguide devices used a 30 μm-wide hybrid Si/QD waveguide; characterization included DC I–V measurements with a 2.1 μm laser coupled through grating couplers and AC bandwidth measurements using a 1.55 μm modulated optical setup.
- To demonstrate scalability, the authors combined an 8-channel WG-QDPD array with a planar concave grating to form a compact spectrometer.
Limitations
- The paper states that the bandwidth of the WG-QDPD “still lags behind” GHz-bandwidth approaches, and that further efforts are needed to reduce nonlinear response.
- It notes that the photocurrent shows nonlinear growth with optical power, attributed to QDPD saturation due to high series resistance, which can limit performance.
- Evident from the text: the reported NEP of 0.13 pW/√Hz for the tapered device is described as underestimated because it was measured at relatively high optical power and under nonlinear response conditions.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
11 Valid · 3 Not valid · 10 Not checked · 71 Own results and interpretations
At least one cited source doesn’t support this claim or points to a different paper, and none confirmed it — see the verdicts below.
In the paper
“and ( 1.41 ± 0.35 ) × 10 -4 cm -2 V -1 s -1 for holes”
What the sources say
- Disputedcites [41] , 2024, Short-wave infrared colloidal QDs photodetector with nanosecond response times enabled by ultrathin absorber layers, Adv. Mater. sourceExperimental — accuracy not yet measured
In Section 2.2 (PbS QD Film Formation) our copy reports FET-derived hole mobilities in the TBAI-treated PbS QD films of 8.12 × 10^-3 and 2.26 × 10^-2 cm² V⁻¹ s⁻¹ (forward/backward gate sweep), and the Discussion (Section 3) again cites ≈4 × 10^-2 cm² V⁻¹ s⁻¹ as the mobility of the films used in this study — two to three orders of magnitude above the (1.41 ± 0.35) × 10^-4 cm² V⁻¹ s⁻¹ attributed here. Our copy also contains no 2.1 μm absorber: the PbS-TBAI layer is the n-type film with bandgap absorption at 1330 nm (paired with a 950 nm p-PbS/EDT layer; Experimental Section describes only 950 nm and 1300 nm QD syntheses). So neither the magnitude nor the 2.1 μm assignment of the claim matches what this paper states. (LLM, conf=0.80)
Checked by a reasoning model — may be wrong.
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Disputed
At least one cited source doesn’t support this claim or points to a different paper, and none confirmed it — see the verdicts below.
In the paper
“The carrier mobility of the 2.1 μ mPbS-TBAI absorption layer, extracted via the field effect transistor (FET) measurements, 41 is ( 0.94 ± 0.6 ) × 10 -4 cm -2 V -1 s -1 for electrons”
What the sources say
- Disputedcites [41] , 2024, Short-wave infrared colloidal QDs photodetector with nanosecond response times enabled by ultrathin absorber layers, Adv. Mater. sourceExperimental — accuracy not yet measured
Our copy reports FET-derived electron mobilities for TBAI-treated PbS QD films of 8.22 × 10^-3 to 7.25 × 10^-2 cm2 V^-1 s^-1 (Section 2.2, PbS QD Film Formation), i.e. two to three orders of magnitude above the claimed (0.94 ± 0.6) × 10^-4, and explicitly frames these as lower limits. The paper also contains no 2.1 μm PbS-TBAI absorber: its n-PbS(TBAI) QDs absorb at 1330 nm and the photoactive stacks are ultrathin (50 nm n-type + 50 nm p-type, 100 nm total; Sections 2.2-2.3, Introduction), with FET modelling using ~4 × 10^-2 cm2 V^-1 s^-1 (Section 2.1). Searches for a 2.1 μm/thick absorber layer and for the 10^-4 mobility value returned nothing in our copy. (LLM, conf=0.78)
Checked by a reasoning model — may be wrong.
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Disputed
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“EDT, known for its high reactivity compared to TBAI, 40 can soak the 1.3 μ m PbS-TBAI layer underneath, resulting in a change of doping to p-type.”
What the sources say
- Partly supportedcites [40] 2020, A chemically orthogonal hole transport layer for efficient colloidal quantum dot solar cells, Adv. Mater. sourceExperimental — accuracy not yet measured
The passage on EDT treatment (section labeled Abstract; page unavailable) says thiols may penetrate the underlying CQD active layer, and XPS results suggest EDT replaces some of its original PbI2 ligands. It does not report a 1.3 μm PbS-TBAI layer or show that the underlying layer changes to p-type; the paper describes the EDT hole-transport layer, not the underlying active layer, as p-type. (LLM, conf=0.88)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“The carrier transition time in the 1.3 μ m PbS-TBAI and 0.94 μ m PbS-EDT layers is disregarded due to the significantly faster carrier mobilities exceeding 1 × 10 -3 cm -2 V -1 s -1 in both layers. 41”
What the sources say
- Partly supportedcites [41] , 2024, Short-wave infrared colloidal QDs photodetector with nanosecond response times enabled by ultrathin absorber layers, Adv. Mater. sourceExperimental — accuracy not yet measured
Section 2.2 (PbS QD Film Formation) supports the mobility half: FET measurements give electron mobilities of 8.22 × 10⁻³ to 7.25 × 10⁻² cm² V⁻¹ s⁻¹ in the TBAI-treated (1330 nm) films and hole mobilities of 8.12 × 10⁻³ to 2.26 × 10⁻² cm² V⁻¹ s⁻¹ in the EDT-treated (950 nm) films — both well above 1 × 10⁻³, and explicitly flagged as lower limits. However, the source does not disregard the carrier transition (drift) time in those layers: Section 2.1 keeps τ_drift = d²/(μV) inside the response-time model (Equations 1–2, Figure 1b/c, noting drift limits thicker devices), and Section 2.3 concludes the 4 ns response of the 50 μm-pad device 'agrees with the expectations for drift-limited transport through a depleted QD film'. What the paper does eliminate is charge-carrier diffusion, by assuming a fully depleted film — not the transit time. Minor mismatch also: the source's absorption peaks are 1330 nm and 950 nm, not 0.94 μm. (LLM, conf=0.72)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“The ITO layer introduced an optical loss of around 0.02 dB/ μ m, resulting from strong free carrier absorption in the infrared. 43”
What the sources say
- Partly supportedcites [43] 2010, Lossy mode resonance generation with indium-tin-oxide-coated optical fibers for sensing applications, J. Lightwave Technol. sourceExperimental — accuracy not yet measured
The Introduction says that a cladding or thin film introduces losses, and the Single LMR Generation section identifies attenuation bands in the ITO-coated fiber. Neither section reports a loss of around 0.02 dB/μm; the cited passages also do not attribute the loss to strong free-carrier absorption in the infrared. Page numbers are unavailable in our copy. (LLM, conf=0.78)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
73 more claims · 6 with their cited sources checked
Create a free account to see all 95 claims and to verify the 3 references still open.
- Probably not a substantial claim. 7
- It may state two separate claims as one. 12
Citations
Cites
Graphene photodetectors for high-speed optical communications
Mueller, T., Xia, F., & Avouris, P. (2010) · Nature Photonics · doi:10.1038/nphoton.2010.40 · Cited by 2,474
Improved performance and stability in quantum dot solar cells through band alignment engineering
Chuang, C.-H. M., Brown, P. R., Bulović, V., & Bawendi, M. G. (2014) · Nature Materials · doi:10.1038/nmat3984 · Cited by 1,795
Progress, Challenges, and Opportunities for 2D Material Based Photodetectors
Long, M., Wang, P., Fang, H., & Hu, W. (2019) · Advanced Functional Materials · doi:10.1002/adfm.201803807 · Cited by 1,598
Energy‐Level Alignment at Organic/Metal and Organic/Organic Interfaces
Braun, S., Salaneck, W. R., & Fahlman, M. (2009) · Advanced Materials · doi:10.1002/adma.200802893 · Cited by 1,593
Chip-integrated ultrafast graphene photodetector with high responsivity
Gan, X., Shiue, R.-J., Gao, Y., Meric, I., Heinz, T. F., Shepard, K., Hone, J., Assefa, S., & Englund, D. (2013) · Nature Photonics · doi:10.1038/nphoton.2013.253 · Cited by 1,151
Waveguide-integrated black phosphorus photodetector with high responsivity and low dark current
Youngblood, N., Chen, C., Koester, S. J., & Li, M. (2015) · Nature Photonics · doi:10.1038/nphoton.2015.23 · Cited by 953
High-responsivity graphene/silicon-heterostructure waveguide photodetectors
Wang, X., Cheng, Z., Xu, K., Tsang, H. K., & Xu, J.-B. (2013) · Nature Photonics · doi:10.1038/nphoton.2013.241 · Cited by 873
Perspective on the future of silicon photonics and electronics
Margalit, N., Xiang, C., Bowers, S. M., Bjorlin, A., Blum, R., & Bowers, J. E. (2021) · Applied Physics Letters · doi:10.1063/5.0050117 · Cited by 641
Mid-infrared HgTe colloidal quantum dot photodetectors
Keuleyan, S., Lhuillier, E., Brajuskovic, V., & Guyot-Sionnest, P. (2011) · Nature Photonics · doi:10.1038/nphoton.2011.142 · Cited by 503
Silicon/2D-material photodetectors: from near-infrared to mid-infrared
Liu, C., Guo, J., Yu, L., Li, J., Zhang, M., Li, H., Shi, Y., & Dai, D. (2021) · Light: Science & Applications · doi:10.1038/s41377-021-00551-4 · Cited by 473
Cited by
Tanghe, I., Vandekerckhove, T., Samoli, M., Waters, A. B., Harankahage, D., Zamkov, M. A., Hens, Z., Seassal, C., Nguyen, H. S., Thourhout, D. V., et al. (2024) · ACS Photonics · doi:10.1021/acsphotonics.4c01410 · Cited by 9
Self-citationXiang, H., Liu, J., Zhao, X., et al. (2025) · Photonics Research · doi:10.1364/prj.567718 · Cited by 6
Qu, J., Peng, 刘. L., Xuetao, 甘. G., & Jianlin, 赵. Z. (2024) · Acta Optica Sinica · doi:10.3788/aos241121 · Cited by 5
Guo, X., Cerutti, L., Rodriguez, J., Tournié, E., Uvin, S., & Roelkens, G. (2024) · Optics Letters · doi:10.1364/ol.543948 · Cited by 4
LI, Z., Luo, Y., Liu, Z., Tang, X., Li, Y., Ding, N., You, M., Wang, M., Pan, Q., Li, K. H., et al. (2025) · Optics Express · doi:10.1364/oe.581982 · Cited by 2
Metadata
- Authors
- Pang, C., Deng, Y.-H., Kheradmand, E., Hagelsieb, L. M., Guo, Y., Cheyns, D., Geiregat, P., Hens, Z., & Van Thourhout, D.
- Affiliations
- Ghent University (BE)
- IMEC (BE)
- Photonics Research Group, Ghent University - IMEC 1 , 9052 Gent, Belgium
- Corresponding author
- Pang, Chao
- ORCID
- Venue
- APL Photonics
- Publisher
- AIP Publishing
- Published
- 2024-06-01
- Volume
- 9
- Issue
- 6
- ISSN
- 2378-0967 (ISSN-L)
- OpenAlex
- W4399857512
- Cited by
- 9
- References
- 55
- Citations by year
- 2026: 3 · 2025: 3 · 2024: 3
- FWCI
- 0.93
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- cc-by
- creativecommons.org/licenses/by/4.0/ (vor, 19 d)
- creativecommons.org/licenses/by/4.0/ (tdm, 19 d)
- Locations
- APL Photonics (publishedVersion, cc-by)
- Ghent University Academic Bibliography (Ghent University) (publishedVersion, cc-by)
- Ghent University Academic Bibliography (Ghent University) (submittedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Funders
- European Research Council (884963)
- Fonds Wetenschappelijk Onderzoek (G0B2921N, G0C5723N)
- Chinese Government Scholarship (201906120023)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Photonic and Optical Devices
- Physical Sciences › Materials Science › Materials Chemistry › Quantum Dots Synthesis And Properties
- Physical Sciences › Physics and Astronomy › Atomic and Molecular Physics, and Optics › Photonic Crystals and Applications
- Keywords
- silicon photonics, colloidal quantum dots, PbS quantum dots, infrared detection, 2 μm wavelength, silicon waveguides, photodetector integration, responsivity, dark current, bandwidth
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (qwen3.8-omni-flash and gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: A silicon photonics waveguide-coupled colloidal quantum dot photodiode sensitive beyond 1.6 µ m. https://app.cochat.ai/papers/10.1063/5.0206386
- The paper
- Pang, C., Deng, Y.-H., Kheradmand, E., Hagelsieb, L. M., Guo, Y., Cheyns, D., Geiregat, P., Hens, Z., & Van Thourhout, D. (2024). A silicon photonics waveguide-coupled colloidal quantum dot photodiode sensitive beyond 1.6 µ m. APL Photonics. https://doi.org/10.1063/5.0206386
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.