Optimization of Lignin Extraction from Pine Wood for Fast Pyrolysis by Using a γ-Valerolactone-Based Binary Solvent System
Open accessThe DOI matches its Crossref record; 79 of the 79 references it cites were found in a registry or an index.
Abstract
Fast pyrolysis of lignin is a promising method to produce aromatic chemicals and fuels. Lignin structure and pyrolysis conditions determine the liquid yield and product selectivity. Extraction of pine wood using γ-valerolactone (GVL) mixed with water in the presence of diluted sulfuric acid obtains lignin (GVL–lignin) which shows different product yield and selectivity. The composition of the extraction medium influences the yield of GVL–lignin and affects its native structure. The GVL-to-water ratio affects the lignin yield without significantly modifying the structure of the extracted lignin, whereas the sulfuric acid concentration affects both the extraction yield and the extracted lignin structure. These structural changes influence the product distribution after fast pyrolysis, which generates phenols and alkoxy phenols as the main products in the liquid fraction. Lignin extracted with a mixture of 4/1 of GVL/H 2 O (w/w) and 0.075 M sulfuric acid solution produces the highest pyrolysis liquid yield. Pyrolysis of GVL–lignin at 750 °C generates the maximum liquid yield. The amount of phenols in fast pyrolysis products increases with increasing temperature and sulfuric acid concentration used in the GVL–lignin extraction. This indicates that the extraction conditions of GVL–lignin may be optimized to increase the selectivity in fast pyrolysis.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“The volatile products distribution shows that G-type phenols are the major compounds due to the nature of Kraft lignin extracted from black liquor [230, 231].”
From A review on lignin pyrolysis: pyrolytic behavior, mechanism, and relevant upgrading for improving process efficiency (2022) · cites this paper as [230]
Citations
Cites
Review of fast pyrolysis of biomass and product upgrading
Bridgwater, A. V. (2012) · Biomass and Bioenergy · doi:10.1016/j.biombioe.2011.01.048 · Cited by 4,856 · cited 1×
“39,40 In 41-45 In this study, pine wood (softwood) was employed as the lignocellulosic biomass source for lignin extraction with GVL/H 2 O solvent in the presence of sulfuric acid.”
Methods for Pretreatment of Lignocellulosic Biomass for Efficient Hydrolysis and Biofuel Production
Kumar, P., Barrett, D. M., Delwiche, M. J., & Stroeve, P. (2009) · Industrial & Engineering Chemistry Research · doi:10.1021/ie801542g · Cited by 3,772 · cited 1×
“…conventionally as a polymer of phenylpropane units (monolignols), namely p -coumaryl, coniferyl and sinapyl alcohols, also called units H, G and S. 9,10 Each unit in the lignin structure is connected by various ether and carbon-carbon linkages, such as β-O-4, 4-O-5, α-O-4, β-β, β-5, β-1 and 5-5.”
Catalytic Transformation of Lignin for the Production of Chemicals and Fuels
Li, C., Zhao, X., Wang, A., Huber, G. W., & Zhang, T. (2015) · Chemical Reviews · doi:10.1021/acs.chemrev.5b00155 · Cited by 2,951 · cited 1×
“39,40 In 41-45 In this study, pine wood (softwood) was employed as the lignocellulosic biomass source for lignin extraction with GVL/H 2 O solvent in the presence of sulfuric acid.”
Pretreatment of Lignocellulosic Wastes to Improve Ethanol and Biogas Production: A Review
Taherzadeh, M. J., & Karimi, K. (2008) · International Journal of Molecular Sciences · doi:10.3390/ijms9091621 · Cited by 2,634
Lignocellulosic biomass pyrolysis mechanism: A state-of-the-art review
Wang, S., Dai, G., Yang, H., & Luo, Z. (2017) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2017.05.004 · Cited by 2,595
Conversion of biomass to selected chemical products
Gallezot, P. (2012) · Chem. Soc. Rev. · doi:10.1039/c1cs15147a · Cited by 2,552
Chemicals from lignin: an interplay of lignocellulose fractionation, depolymerisation, and upgrading
Schutyser, W., Renders, T., Van den Bosch, S., Koelewijn, S.-F., Beckham, G. T., & Sels, B. F. (2018) · Chemical Society Reviews · doi:10.1039/c7cs00566k · Cited by 2,552
Bright Side of Lignin Depolymerization: Toward New Platform Chemicals
Sun, Z., Fridrich, B., de Santi, A., Elangovan, S., & Barta, K. (2018) · Chemical Reviews · doi:10.1021/acs.chemrev.7b00588 · Cited by 2,191 · cited 1×
“15 16-18 Thus, the organosolv method generates lignin which is more amenable towards depolymerization.”
Paving the Way for Lignin Valorisation: Recent Advances in Bioengineering, Biorefining and Catalysis
Rinaldi, R., Jastrzebski, R., Clough, M. T., Ralph, J., Kennema, M., Bruijnincx, P. C. A., & Weckhuysen, B. M. (2016) · Angewandte Chemie International Edition · doi:10.1002/anie.201510351 · Cited by 2,138 · cited 1×
“19 20-22 In addition, side reactions such as cleavage of aryl ether linkages, ethoxylation and condensation reactions can take place, resulting in undesired structure modifications.”
Chemical modification of lignins: Towards biobased polymers
Laurichesse, S., & Avérous, L. (2014) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2013.11.004 · Cited by 2,058 · cited 1×
“35 36-38 In fast pyrolysis, lignin is thermally treated using very high heating rates and short vapor residence times, followed by a rapid cooling of the pyrolysis vapors to obtain bio-oil containing important amounts of aromatic compounds.”
Biomass pretreatment: Fundamentals toward application
Agbor, V. B., Cicek, N., Sparling, R., Berlin, A., & Levin, D. B. (2011) · Biotechnology Advances · doi:10.1016/j.biotechadv.2011.05.005 · Cited by 1,985
A comprehensive review on the pyrolysis of lignocellulosic biomass
Dhyani, V., & Bhaskar, T. (2018) · Renewable Energy · doi:10.1016/j.renene.2017.04.035 · Cited by 1,545 · cited 1×
“13 However, lignin properties and its isolation yield depend on its source (e.g. softwood or hardwood) and the extraction technique applied.”
Review of biomass pyrolysis oil properties and upgrading research
Zhang, Q., Chang, J., Wang, T., & Xu, Y. (2007) · Energy Conversion and Management · doi:10.1016/j.enconman.2006.05.010 · Cited by 1,472
Formaldehyde stabilization facilitates lignin monomer production during biomass depolymerization
Shuai, L., Amiri, M. T., Questell-Santiago, Y. M., Héroguel, F., Li, Y., Kim, H., Meilan, R., Chapple, C., Ralph, J., & Luterbacher, J. S. (2016) · Science · doi:10.1126/science.aaf7810 · Cited by 1,404
Self-citationPyrolysis of biomass to produce fuels and chemical feedstocks
Yaman, S. (2004) · Energy Conversion and Management · doi:10.1016/s0196-8904(03)00177-8 · Cited by 1,224 · cited 1×
“35 36-38 In fast pyrolysis, lignin is thermally treated using very high heating rates and short vapor residence times, followed by a rapid cooling of the pyrolysis vapors to obtain bio-oil containing important amounts of aromatic compounds.”
γ-Valerolactone—a sustainable liquid for energy and carbon-based chemicals
Horváth, I. T., Mehdi, H., Fábos, V., Boda, L., & Mika, L. T. (2008) · Green Chem. · doi:10.1039/b712863k · Cited by 992
Importance of chemical pretreatment for bioconversion of lignocellulosic biomass
Behera, S., Arora, R., Nandhagopal, N., & Kumar, S. (2014) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2014.04.047 · Cited by 946 · cited 1×
“14 Regular solvents used in this process include methanol, ethanol, acetone, ethylene glycol, triethylene glycol and tetrahydrofurfuryl alcohol.”
Stefanidis, S. D., Kalogiannis, K. G., Iliopoulou, E. F., Michailof, C. M., Pilavachi, P. A., & Lappas, A. A. (2014) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2013.10.013 · Cited by 775 · cited 1×
“7 Each type of lignocellulosic biomass contains different amounts of these components.”
Nonenzymatic Sugar Production from Biomass Using Biomass-Derived γ-Valerolactone
Luterbacher, J. S., Rand, J. M., Alonso, D. M., Han, J., Youngquist, J. T., Maravelias, C. T., Pfleger, B. F., & Dumesic, J. A. (2014) · Science · doi:10.1126/science.1246748 · Cited by 705 · cited 1×
“60 The lignins extracted from pine wood by varying the GVL/H 2 O (w/w) ratio were pyrolyzed at 750 °C with a heating rate of 20 °C/ms and a residence time of 20 s (Figure 2A).”
Self-citationBiomass pyrolysis-a review of modelling, process parameters and catalytic studies
Sharma, A., Pareek, V., & Zhang, D. (2015) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2015.04.193 · Cited by 675
Kabir, G., & Hameed, B. H. (2017) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2016.12.001 · Cited by 591
Characterization of milled wood lignin and ethanol organosolv lignin from miscanthus
El Hage, R., Brosse, N., Chrusciel, L., Sanchez, C., Sannigrahi, P., & Ragauskas, A. (2009) · Polymer Degradation and Stability · doi:10.1016/j.polymdegradstab.2009.07.007 · Cited by 511 · cited 1×
“72-76 The characteristic bands at 2839 and 1210 cm -1 , attributed to the C-H stretching in -OCH 3 and the C-O stretching, respectively, can be used to analyze the structural changes of the GVL-lignins.”
Understanding the Fast Pyrolysis of Lignin
Patwardhan, P. R., Brown, R. C., & Shanks, B. H. (2011) · ChemSusChem · doi:10.1002/cssc.201100133 · Cited by 468
Influence of temperature on the products from the flash pyrolysis of biomass
Horne, P. A., & Williams, P. T. (1996) · Fuel · doi:10.1016/0016-2361(96)00081-6 · Cited by 398
Integrated conversion of hemicellulose and cellulose from lignocellulosic biomass
Alonso, D. M., Wettstein, S. G., Mellmer, M. A., Gurbuz, E. I., & Dumesic, J. A. (2013) · Energy Environ. Sci. · doi:10.1039/c2ee23617f · Cited by 380
Onay, O. (2007) · Fuel Processing Technology · doi:10.1016/j.fuproc.2007.01.001 · Cited by 363
Controlling the selectivity to chemicals from lignin via catalytic fast pyrolysis
Ma, Z., Troussard, E., & van Bokhoven, J. A. (2012) · Applied Catalysis A: General · doi:10.1016/j.apcata.2012.02.027 · Cited by 363
Self-citationCharacterization of bio-oil, syn-gas and bio-char from switchgrass pyrolysis at various temperatures
Imam, T., & Capareda, S. (2012) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2011.11.010 · Cited by 345
Milled Wood Lignin: A Linear Oligomer
Crestini, C., Melone, F., Sette, M., & Saladino, R. (2011) · Biomacromolecules · doi:10.1021/bm200948r · Cited by 335 · cited 1×
“…conventionally as a polymer of phenylpropane units (monolignols), namely p -coumaryl, coniferyl and sinapyl alcohols, also called units H, G and S. 9,10 Each unit in the lignin structure is connected by various ether and carbon-carbon linkages, such as β-O-4, 4-O-5, α-O-4, β-β, β-5, β-1 and 5-5.”
Effect of the Temperature on the Composition of Lignin Pyrolysis Products
Jiang, G., Nowakowski, D. J., & Bridgwater, A. V. (2010) · Energy & Fuels · doi:10.1021/ef100363c · Cited by 332
96/05110 Influence of temperature on the products from the flash pyrolysis of biomass
(1996) · Fuel and Energy Abstracts · doi:10.1016/0140-6701(96)89813-4 · Cited by 313
New insights into the molecular architecture of hardwood lignins by chemical degradative methods
Lapierre, C., Pollet, B., & Rolando, C. (1995) · Research on Chemical Intermediates · doi:10.1007/bf03052266 · Cited by 292 · cited 1×
“11,12 Generally, softwood lignin contains coniferyl alcohol and hardwood lignin both coniferyl and sinapyl alcohols as predominant units.”
Shen, D., Jin, W., Hu, J., Xiao, R., & Luo, K. (2015) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2015.06.054 · Cited by 284 · cited 1×
“4 The relevance of a certain type of biomass in a specific region depends on its availability, which often depends on technical, economic, environmental and other factors.”
Bio-oil from fast pyrolysis of lignin: Effects of process and upgrading parameters
Fan, L., Zhang, Y., Liu, S., Zhou, N., Chen, P., Cheng, Y., Addy, M., Lu, Q., Omar, M. M., Liu, Y., et al. (2017) · Bioresource Technology · doi:10.1016/j.biortech.2017.05.129 · Cited by 265
Tang, X., Zeng, X., Li, Z., Hu, L., Sun, Y., Liu, S., Lei, T., & Lin, L. (2014) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2014.07.209 · Cited by 265
Zhao, X., Li, S., Wu, R., & Liu, D. (2017) · Biofuels, Bioproducts and Biorefining · doi:10.1002/bbb.1768 · Cited by 249
Lignin monomer production integrated into the γ-valerolactone sugar platform
Luterbacher, J. S., Azarpira, A., Motagamwala, A. H., Lu, F., Ralph, J., & Dumesic, J. A. (2015) · Energy & Environmental Science · doi:10.1039/c5ee01322d · Cited by 248 · cited 1×
“28 Therefore, a fine-tuning of the conditions may enable improved control of the selectivity in fast pyrolysis.”
Self-citationMonolignol acylation and lignin structure in some nonwoody plants: A 2D NMR study
Martínez, Á. T., Rencoret, J., Marques, G., Gutiérrez, A., Ibarra, D., Jiménez-Barbero, J., & del Río, J. C. (2008) · Phytochemistry · doi:10.1016/j.phytochem.2008.09.005 · Cited by 227
Azadfar, M., Gao, A. H., Bule, M. V., & Chen, S. (2015) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2014.12.049 · Cited by 213
Hemberger, P., Custodis, V. B. F., Bodi, A., Gerber, T., & van Bokhoven, J. A. (2017) · Nature Communications · doi:10.1038/ncomms15946 · Cited by 198 · cited 1×
“39,40 In 41-45 In this study, pine wood (softwood) was employed as the lignocellulosic biomass source for lignin extraction with GVL/H 2 O solvent in the presence of sulfuric acid.”
Phenol and phenolics from lignocellulosic biomass by catalytic microwave pyrolysis
Bu, Q., Lei, H., Ren, S., Wang, L., Holladay, J., Zhang, Q., Tang, J., & Ruan, R. (2011) · Bioresource Technology · doi:10.1016/j.biortech.2011.04.025 · Cited by 192
Catalytic fast pyrolysis of Kraft lignin with HZSM-5 zeolite for producing aromatic hydrocarbons
Li, X., Su, L., Wang, Y., Yu, Y., Wang, C., Li, X., & Wang, Z. (2012) · Frontiers of Environmental Science & Engineering · doi:10.1007/s11783-012-0410-2 · Cited by 187
Xue, Z., Zhao, X., Sun, R.-C., & Mu, T. (2016) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.6b00639 · Cited by 184
Sun, F., & Chen, H. (2008) · Bioresource Technology · doi:10.1016/j.biortech.2007.11.001 · Cited by 182
Gamma-valerolactone-based solvents
Fegyverneki, D., Orha, L., Láng, G., & Horváth, I. T. (2010) · Tetrahedron · doi:10.1016/j.tet.2009.11.013 · Cited by 181
Wood Based Lignin Reactions Important to the Biorefinery and Pulp and Paper Industries
Santos, R. B., Hart, P., Jameel, H., & Chang, H.-M. (2013) · BioResources · doi:10.15376/biores.8.1.1456-1477 · Cited by 169 · cited 1×
“78 This is noted from the signals related to the side-chains of lignin obtained with different sulfuric acid concentrations (Figure 6) in accordance with loss of β -O-4 structures, producing more condensed structures.”
Lignin Composition and Structure Differs between Xylem, Phloem and Phellem in Quercus suber L.
Lourenço, A., Rencoret, J., Chemetova, C., Gominho, J., Gutiérrez, A., del Río, J. C., & Pereira, H. (2016) · Frontiers in Plant Science · doi:10.3389/fpls.2016.01612 · Cited by 164
Green Solvents in Biomass Processing
Soh, L., & Eckelman, M. J. (2016) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.6b01635 · Cited by 161 · cited 1×
“24 32-34 Lignin can be converted into useful liquids (bio-oil), gases and char by pyrolysis as thermochemical decomposition process.”
Fast pyrolysis of rice husk under different reaction conditions
Heo, H. S., Park, H. J., Dong, J.-I., Park, S. H., Kim, S., Suh, D. J., Suh, Y.-W., Kim, S.-S., & Park, Y.-K. (2010) · Journal of Industrial and Engineering Chemistry · doi:10.1016/j.jiec.2010.01.026 · Cited by 159
Lignin variability in plant cell walls: Contribution of new models
Neutelings, G. (2011) · Plant Science · doi:10.1016/j.plantsci.2011.06.012 · Cited by 156 · cited 1×
“11,12 Generally, softwood lignin contains coniferyl alcohol and hardwood lignin both coniferyl and sinapyl alcohols as predominant units.”
Rencoret, J., Marques, G., Gutiérrez, A., Nieto, L., Santos, J. I., Jiménez-Barbero, J., Martínez, Á. T., & del Río, J. C. (2009) · hfsg · doi:10.1515/hf.2009.070 · Cited by 154
Aromatics Production via Catalytic Pyrolysis of Pyrolytic Lignins from Bio-Oil
Zhao, Y., Deng, L., Liao, B., Fu, Y., & Guo, Q.-X. (2010) · Energy & Fuels · doi:10.1021/ef100896q · Cited by 145
Bioenergy in Switzerland: Assessing the domestic sustainable biomass potential
Steubing, B. R. P., Zah, R., Wäger, P. A., & Ludwig, C. D. R. (2010) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2010.03.036 · Cited by 140
Investigation of structural modification and thermal characteristics of lignin after heat treatment
Kim, J., Hwang, H., Oh, S., Kim, Y., Kim, U., & Choi, J. W. (2014) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2014.02.013 · Cited by 138 · cited 1×
“57,79,80 In addition, there is an important decrease in the maximum devolatilization rate of GVL-lignins extracted with mixtures containing solutions of initial concentration of 0.125-0.275 M sulfuric acid with respect to 0.075 M sulfuric acid, which is consistent with previous results reported by…”
InfluentialLi, J., Wang, W., Zhang, S., Gao, Q., Zhang, W., & Li, J. (2016) · RSC Advances · doi:10.1039/c6ra11966b · Cited by 134
Wen, J.-L., Sun, S.-L., Yuan, T.-Q., Xu, F., & Sun, R.-C. (2013) · Journal of Agricultural and Food Chemistry · doi:10.1021/jf403717q · Cited by 126 · cited 1×
“22,23 Trying to minimize these problems, green solvents have attracted attention in recent years for biomass processing.”
Wood biorefinery based on γ-valerolactone/water fractionation
Lê, H. Q., Ma, Y., Borrega, M., & Sixta, H. (2016) · Green Chemistry · doi:10.1039/c6gc01692h · Cited by 126
Naqvi, S. R., Uemura, Y., & Yusup, S. B. (2013) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2013.12.009 · Cited by 120
Characterization of lignin isolated from some nonwood available in Bangladesh
Jahan, M. S., Chowdhury, D., Islam, M. K., & Moeiz, S. M. I. (2006) · Bioresource Technology · doi:10.1016/j.biortech.2006.01.005 · Cited by 112
Custodis, V. B. F., Karakoulia, S. A., Triantafyllidis, K. S., & van Bokhoven, J. A. (2016) · ChemSusChem · doi:10.1002/cssc.201600105 · Cited by 108
Selective deoxygenation of lignin during catalytic fast pyrolysis
Ma, Z., Custodis, V., & van Bokhoven, J. A. (2014) · Catalysis Science & Technology · doi:10.1039/c3cy00704a · Cited by 105
Self-citationPhenols and aromatics from fast pyrolysis of variously prepared lignins from hard- and softwoods
Custodis, V. B. F., Bährle, C., Vogel, F., & van Bokhoven, J. A. (2015) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2015.07.018 · Cited by 103 · cited 2×
“GVL-lignin pyrolysis results were compared to others previously reported by Custodis et al. 44 , which studied similar fast pyrolysis of lignins separated by dioxane-, Klason-, and organsolv-methods.”
Advanced Biorefinery based on the Fractionation of Biomass in γ‐Valerolactone and Water
Fang, W., & Sixta, H. (2014) · ChemSusChem · doi:10.1002/cssc.201402821 · Cited by 100
Solubility of Organosolv Lignin in γ‐Valerolactone/Water Binary Mixtures
Lê, H. Q., Zaitseva, A., Pokki, J., Ståhl, M., Alopaeus, V., & Sixta, H. (2016) · ChemSusChem · doi:10.1002/cssc.201600655 · Cited by 93 · cited 3×
“Lignin solubility in GVL/H 2 O is insignificant up to 32 wt% of GVL. 55 Above this concentration, the mixture tends to split into two phases and lignin solubility greatly increases.”
Stability of gamma-valerolactone under neutral, acidic, and basic conditions
Wong, C. Y. Y., Choi, A. W., Lui, M. Y.-Y., Fridrich, B., Horváth, A. K., Mika, L. T., & Horváth, I. T. (2016) · Structural Chemistry · doi:10.1007/s11224-016-0887-6 · Cited by 85 · cited 1×
“58 The lowest content of GVL in the solvent mixture was ca. 45 wt% for the combination of 1/1 of GVL/H 2 O (w/w) with the different sulfuric acid solutions, and above 50 wt% for the other mixtures (Table S1).”
Nikafshar, S., Zabihi, O., Moradi, Y., Ahmadi, M., Amiri, S., & Naebe, M. (2017) · Polymers · doi:10.3390/polym9070266 · Cited by 85 · cited 2×
“76 Moreover, the functional groups of GVL-lignin were confirmed by 1 H NMR (Figure S1).”
The influence of interunit carbon–carbon linkages during lignin upgrading
Shuai, L., Amiri, M. T., & Luterbacher, J. S. (2016) · Current Opinion in Green and Sustainable Chemistry · doi:10.1016/j.cogsc.2016.10.001 · Cited by 84
Self-citationDeactivation and Regeneration of H‐USY Zeolite during Lignin Catalytic Fast Pyrolysis
Ma, Z., & van Bokhoven, J. A. (2012) · ChemCatChem · doi:10.1002/cctc.201200401 · Cited by 75
Self-citationThe Pyrolytic Behavior of Selected Lignin Preparations
Gardner, D. J., Schultz, T. P., & McGinnis, G. D. (1985) · Journal of Wood Chemistry and Technology · doi:10.1080/02773818508085182 · Cited by 73 · cited 2×
“79 The results evidence that the extraction conditions affect the lignin and then the products distribution in fast pyrolysis.”
InfluentialKim, Y., Jae, J., Myung, S., Sung, B. H., Dong, J.-I., & Park, Y. (2016) · Bioresource Technology · doi:10.1016/j.biortech.2016.08.001 · Cited by 64 · cited 1×
“49,50 In contrast, the char yield decreased from 550 to (650-850) °C.”
Li, S., Li, M., Yu, P., Fan, Y., Jia-Nan, S., & Sun, R. (2017) · Bioresource Technology · doi:10.1016/j.biortech.2017.01.041 · Cited by 62
Fast Pyrolysis of Lignin Using a Pyrolysis Centrifuge Reactor
Trinh, T. N., Jensen, P. A., Sárossy, Z., Dam-Johansen, K., Knudsen, N. O., Sørensen, H. R., & Egsgaard, H. (2013) · Energy & Fuels · doi:10.1021/ef400527k · Cited by 60
Angelini, S., Ingles, D., Gelosia, M., Cerruti, P., Pompili, E., Scarinzi, G., Cavalaglio, G., Cotana, F., & Malinconico, M. (2017) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2017.03.062 · Cited by 59
Wu, M., Liu, J.-K., Yan, Z., Wang, B., Zhang, X., Xu, F., & Sun, R. (2016) · RSC Advances · doi:10.1039/c5ra23095k · Cited by 43
Ma, Z., Ghosh, A., Asthana, N., & van Bokhoven, J. (2017) · ChemCatChem · doi:10.1002/cctc.201601674 · Cited by 41
Self-citationTHE EFFECT OF INITIAL ACID CONCENTRATION ON THE LIGNIN ISOLATED BY THE ACIDOLYSIS OF ASPEN WOOD
Pepper, J. M., & Siddiqueullah, M. (1961) · Canadian Journal of Chemistry · doi:10.1139/v61-185 · Cited by 39
Vapour pressures and enthalpies of vapourization of a series of the γ-lactones
Emel′yanenko, V. N., Kozlova, S. A., Verevkin, S. P., & Roganov, G. N. (2008) · The Journal of Chemical Thermodynamics · doi:10.1016/j.jct.2008.02.002 · Cited by 39 · cited 1×
“24 32-34 Lignin can be converted into useful liquids (bio-oil), gases and char by pyrolysis as thermochemical decomposition process.”
The Influence of Zeolites on Radical Formation During Lignin Pyrolysis
Bährle, C., Custodis, V. B. F., Jeschke, G., van Bokhoven, J. A., & Vogel, F. (2016) · ChemSusChem · doi:10.1002/cssc.201600582 · Cited by 33
Cheng, Y., Zhao, P.-X., Alma, M. H., Sun, D., Li, R., & Jiang, J. (2016) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2016.07.022 · Cited by 21 · cited 1×
“The 1 H NMR results showed that GVL-lignin consists of six major functional groups, in accordance with other lignins 77 Structural changes occur in lignin due to mild acidic conditions during extraction.”
Research works printed but not linked: 2
- 2018, Swiss National Forest Inventory
- Brasch D. J., 1965, Tappi, 48, 245
Cited by
Downstream processing of lignin derived feedstock into end products
Wong, S. S., Shu, R., Zhang, J., Liu, H., & Yan, N. (2020) · Chemical Society Reviews · doi:10.1039/d0cs00134a · Cited by 528
Current advancement on the isolation, characterization and application of lignin
Liao, J. J., Latif, N. H. A., Trache, D., Brosse, N., & Hussin, M. H. (2020) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2020.06.168 · Cited by 425
Lu, X., & Gu, X. (2022) · Biotechnology for Biofuels and Bioproducts · doi:10.1186/s13068-022-02203-0 · Cited by 354
“The volatile products distribution shows that G-type phenols are the major compounds due to the nature of Kraft lignin extracted from black liquor [230, 231].”
BackgroundAntibacterial lignin-based nanoparticles and their use in composite materials
Morena, A. G., & Tzanov, T. (2022) · Nanoscale Advances · doi:10.1039/d2na00423b · Cited by 160
Wang, R., Wang, K., Zhou, M., Xu, J., & Jiang, J. (2021) · Bioresource Technology · doi:10.1016/j.biortech.2021.124873 · Cited by 147
Metadata
- Authors
- Jampa, S., Puente-Urbina, A., Ma, Z., Wongkasemjit, S., Luterbacher, J. S., & van Bokhoven, J. A.
- Affiliations
- Chulalongkorn University (TH)
- ETH Zurich (CH)
- École Polytechnique Fédérale de Lausanne (CH)
- Department of Chemistry and Applied Biosciences, Institute for Chemical and Bioengineering, ETH Zurich, HCI E 127, Vladimir-Prelog-Weg 1, 8093 Zurich, Switzerland
- ORCID
- Venue
- ACS Sustainable Chemistry & Engineering
- Publisher
- American Chemical Society (ACS)
- Published
- 2019-01-20
- Volume
- 7
- Issue
- 4
- Pages
- 4058-4068
- ISSN
- 2168-0485 (ISSN-L)
- OpenAlex
- W2910786090
- Cited by
- 45
- References
- 79
- Citations by year
- 2026: 5 · 2025: 12 · 2024: 7 · 2023: 4 · 2022: 5 · 2021: 3 · 2020: 7 · 2019: 2
- FWCI
- 1.50
- Type
- journal article
- Language
- en
- Open access
- green
- infoscience.epfl.ch
- Licence
- Locations
- ACS Sustainable Chemistry & Engineering (publishedVersion)
- DORA PSI (Paul Scherrer Institute) (submittedVersion)
- Infoscience (Ecole Polytechnique Fédérale de Lausanne) (submittedVersion, cc-by-nc-nd)
- Funders
- Ministry of Science and Technology of Thailand
- Ministerio de Ciencia Tecnología y Telecomunicaciones
- Thailand Research Fund
- Instituto Tecnológico de Costa Rica
- Topics
- Physical Sciences › Chemical Engineering › Process Chemistry and Technology › Lignin and Wood Chemistry
- Physical Sciences › Energy › Fuel Technology › Thermochemical Biomass Conversion Processes
- Physical Sciences › Chemical Engineering › Catalysis › Catalysis for Biomass Conversion
- Keywords
- lignin extraction, pine forest, fast pyrolysis, γ-valerolactone, mixed solvents, sulfuric acid, lignin structure, phenols, pyrolysis temperature, extraction optimization
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.