The DOI matches its Crossref record; 37 of the 37 references it cites were found in a registry or an index.
Fast Pyrolysis of Oil Mallee Woody Biomass: Effect of Temperature on the Yield and Quality of Pyrolysis Products
Abstract
This paper presents an investigation of the production of crude bio-oil, char, and pyrolytic gases from the fast pyrolysis of mallee woody biomass in Australia. The feedstock was ground, sieved to several narrow particle size ranges, and dried prior to pyrolysis in a novel laboratory-scale fluidized-bed reactor. The effects of pyrolysis temperature (350−600 °C), and biomass particle size (100−600 μm), on the yields and composition of bio-oil, gas, and char are reported. In agreement with previous reports, the pyrolysis temperature has an important impact on the yield and composition of bio-oil, char, and gases. Biomass particle size has a significant effect on the water content of bio-oil. It is interesting to note that the temperature for maximum bio-oil yield, between 450 and 475 °C, resulted in an oil with the highest content of oligomers and, consequently, with the highest viscosity. Such observations suggest that the conventional viewpoint of pyrolyzing biomass at temperatures over 400 °C to maximize bio-oil yield needs to be carefully reevaluated, considering the final use of the produced bio-oil. The increases in oil yield with increasing temperature from 350 to 500 °C were mainly due to the increases in the production of lignin-derived oligomers insoluble in water but soluble in CH 2 Cl 2 . The yield and some fuel properties of the pyrolysis products were compared with those herein obtained for pine as well as those reported in the literature for other lignocellulosic feedstocks but using similar reactors.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Overview of Applications of Biomass Fast Pyrolysis Oil
Czernik, S., & Bridgwater, A. V. (2004) · Energy & Fuels · doi:10.1021/ef034067u · Cited by 2,880
An overview of fast pyrolysis of biomass
Bridgwater, A. V., Meier, D., & Radlein, D. (1999) · Organic Geochemistry · doi:10.1016/s0146-6380(99)00120-5 · Cited by 1,752
Fast pyrolysis processes for biomass
Bridgwater, A. (2000) · Renewable and Sustainable Energy Reviews · doi:10.1016/s1364-0321(99)00007-6 · Cited by 1,751
Fast pyrolysis of biomass : a handbook
Bridgwater, A. V. (1999) · Medical Entomology and Zoology · Cited by 662
Developments in Thermochemical Biomass Conversion: Volume 1 / Volume 2
(1997) · Springer eBooks · doi:10.1007/978-94-009-1559-6 · Cited by 644
Progress in Thermochemical Biomass Conversion
(2001) · Wiley eBooks · doi:10.1002/9780470694954 · Cited by 552
Characterization of bio-oils in chemical families
Garcia-Perez, M., Chaala, A., Pakdel, H., Kretschmer, D., & Roy, C. (2007) · Biomass and Bioenergy · doi:10.1016/j.biombioe.2006.02.006 · Cited by 498
Self-citationProduct Distribution from Pyrolysis of Wood and Agricultural Residues
Di Blasi, C., Signorelli, G., Di Russo, C., & Rea, G. (1999) · Industrial & Engineering Chemistry Research · doi:10.1021/ie980711u · Cited by 441
State of the art of applied fast pyrolysis of lignocellulosic materials — a review
Meier, D., & Faix, O. (1999) · Bioresource Technology · doi:10.1016/s0960-8524(98)00086-8 · Cited by 417
On the mechanism of the rapid pyrolysis of cellulose
Piskorz, J., Radlein, D., & Scott, D. S. (1986) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/0165-2370(86)85003-3 · Cited by 361
Bench-Scale Fluidized-Bed Pyrolysis of Switchgrass for Bio-Oil Production
Boateng, A. A., Daugaard, D. E., Goldberg, N. M., & Hicks, K. B. (2007) · Industrial & Engineering Chemistry Research · doi:10.1021/ie0614529 · Cited by 277
Vacuum pyrolysis of sugarcane bagasse
Garcı̀a-Pèrez, M., Chaala, A., & Roy, C. (2002) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/s0165-2370(01)00184-x · Cited by 265
The role of temperature in the fast pyrolysis of cellulose and wood
Scott, D. S., Piskorz, J., Bergougnou, M. A., Graham, R., & Overend, R. P. (1988) · Industrial & Engineering Chemistry Research · doi:10.1021/ie00073a003 · Cited by 241
Biomass Pyrolysis in a Fluidized Bed Reactor. Part 1: Literature Review and Model Simulations
Kersten, S. R. A., Wang, X., Prins, W., & van Swaaij, W. P. M. (2005) · Industrial & Engineering Chemistry Research · doi:10.1021/ie0504856 · Cited by 233
Self-citationFluidization of biomass particles: A review of experimental multiphase flow aspects
Cui, H., & Grace, J. R. (2006) · Chemical Engineering Science · doi:10.1016/j.ces.2006.08.006 · Cited by 229
The use of biomass residues in the Brazilian soluble coffee industry
Silva, M. A., Nebra, S. A., Machado Silva, M. J., & Sanchez, C. G. (1998) · Biomass and Bioenergy · doi:10.1016/s0961-9534(97)10034-4 · Cited by 222
Biomass Pyrolysis in a Fluidized Bed Reactor. Part 2: Experimental Validation of Model Results
Wang, X., Kersten, S. R. A., Prins, W., & van Swaaij, W. P. M. (2005) · Industrial & Engineering Chemistry Research · doi:10.1021/ie050486y · Cited by 219
Self-citationA second look at fast pyrolysis of biomass—the RTI process
Scott, D. S., Majerski, P., Piskorz, J., & Radlein, D. (1999) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/s0165-2370(99)00006-6 · Cited by 215
Vacuum pyrolysis of softwood and hardwood biomass
Garcìa-Pérez, M., Chaala, A., Pakdel, H., Kretschmer, D., & Roy, C. (2007) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2006.05.003 · Cited by 203
Co-pyrolysis of sugarcane bagasse with petroleum residue. Part I: thermogravimetric analysis
Garcı̀a-Pèrez, M., Chaala, A., Yang, J., & Roy, C. (2001) · Fuel · doi:10.1016/s0016-2361(00)00215-5 · Cited by 192
Fast pyrolysis of natural polysaccharides as a potential industrial process
Radlein, D., Piskorz, J., & Scott, D. S. (1991) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/0165-2370(91)80034-6 · Cited by 183
Heterogeneous cracking of wood pyrolysis tars over fresh wood char surfaces
Boroson, M. L., Howard, J. B., Longwell, J. P., & Peters, W. (1989) · Energy & Fuels · doi:10.1021/ef00018a014 · Cited by 177
Properties of bio-oils produced by biomass fast pyrolysis in a cyclone reactor
Lédé, J., Broust, F., Ndiaye, F. T., & FERRER, M. (2007) · Fuel · doi:10.1016/j.fuel.2006.12.024 · Cited by 166
Characterization of the water-insoluble fraction from fast pyrolysis liquids (pyrolytic lignin)
Bayerbach, R., Nguyen, V. D., Schurr, U., & Meier, D. (2006) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2006.02.002 · Cited by 158
Flash pyrolysis of cellulose for production of anhydro-oligomers
Piskorz, J., Majerski, P., Radlein, D. S. A. G., Vladars-Usas, A., & Scott, D. S. (2000) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/s0165-2370(00)00089-9 · Cited by 157
Fast pyrolysis of sweet sorghum and sweet sorghum bagasse
Piskorz, J., Majerski, P., Radlein, D. S. A. G., Scott, D. S., & Bridgwater, A. V. (1998) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/s0165-2370(98)00067-9 · Cited by 139
Multiphase Structure of Bio-oils
Garcı̀a-Pèrez, M., Chaala, A., Pakdel, H., Kretschmer, D., Rodrigue, D., & Roy, C. (2005) · Energy & Fuels · doi:10.1021/ef050248f · Cited by 125
Fast Pyrolysis of Stored Biomass Feedstocks
Agblevor, F. A., Beşler, S., & Wiselogel, A. E. (1995) · Energy & Fuels · doi:10.1021/ef00052a010 · Cited by 121
Production of Mallee Biomass in Western Australia: Energy Balance Analysis
Wu, H., Fu, Q., Giles, R. C., & Bartle, J. (2007) · Energy & Fuels · doi:10.1021/ef7002969 · Cited by 105
Self-citationKang, B.-S., Lee, K. H., Park, H. J., Park, Y., & Kim, J.-S. (2005) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2005.06.012 · Cited by 103
SANS Analysis of the Microstructural Evolution during the Aging of Pyrolysis Oils from Biomass
Fratini, E., Bonini, M., Oasmaa, A., Solantausta, Y., Teixeira, J., & Baglioni, P. (2005) · Langmuir · doi:10.1021/la051990a · Cited by 95
Gómez, C. J., Mészáros, E., Jakab, E., García, E. V., & Puigjaner, L. (2007) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2007.05.003 · Cited by 93
Bartle, J., Olsen, G., Cooper, D., et al. (2007) · International Journal of Global Energy Issues · doi:10.1504/ijgei.2007.013652 · Cited by 82
Characterisation of oligomers and sugar ring-cleavage products in the pyrolysate of cellulose
Lomax, J. A., Commandeur, J., Arisz, P. W., & Boon, J. J. (1991) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/0165-2370(91)80035-7 · Cited by 81
Effects of Diammonium Phosphate on the Yields and Composition of Products from Wood Pyrolysis
Blasi, C. D., Branca, C., & Galgano, A. (2006) · Industrial & Engineering Chemistry Research · doi:10.1021/ie0612616 · Cited by 72
Softwood Bark Pyrolysis Oil-PF Resols. Part 1. Resin Synthesis and OSB Mechanical Properties
Amen-Chen, C., Riedl, B., Wang, X., & Roy, C. (2002) · Holzforschung · doi:10.1515/hf.2002.028 · Cited by 55
Self-citationKinetic study of fast pyrolysis of sawdust in a conical spouted bed reactor in the range 400–500 °C
Olazar, M., Aguado, R., José, M. J. S., & Bilbao, J. (2001) · Journal of Chemical Technology & Biotechnology · doi:10.1002/jctb.409 · Cited by 49
Cited by
Kan, T., Strezov, V., & Evans, T. J. (2016) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2015.12.185 · Cited by 2,239
Kim, K. H., Kim, J.-Y., Cho, T.-S., & Choi, J. W. (2012) · Bioresource Technology · doi:10.1016/j.biortech.2012.04.094 · Cited by 696
A review on operating parameters for optimum liquid oil yield in biomass pyrolysis
Akhtar, J., & Saidina Amin, N. (2012) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2012.05.033 · Cited by 692
Operating parameters for bio-oil production in biomass pyrolysis: A review
Guedes, R. E., Luna, A. S., & Torres, A. R. (2018) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2017.11.019 · Cited by 619
Fates of Chemical Elements in Biomass during Its Pyrolysis
Liu, W.-J., Li, W.-W., Jiang, H., & Yu, H.-Q. (2017) · Chemical Reviews · doi:10.1021/acs.chemrev.6b00647 · Cited by 614
Metadata
- Authors
- Garcia-Perez, M., Wang, X. S., Shen, J., Rhodes, M. J., Tian, F., Lee, W.-J., Wu, H., & Li, C.-Z.
- Venue
- Industrial & Engineering Chemistry Research
- Publisher
- American Chemical Society (ACS)
- Published
- 2008-02-16
- Volume
- 47
- Issue
- 6
- Pages
- 1846-1854
- ISSN
- 0888-5885 (ISSN-L)
- 1520-5045
- OpenAlex
- W2033097910
- Cited by
- 391
- References
- 37
- FWCI
- 11.72
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.