The DOI matches its Crossref record; 28 of the 28 references it cites were found in a registry or an index.
The Build-Up of Polyelectrolyte Multilayers of Microfibrillated Cellulose and Cationic Polyelectrolytes
Abstract
A new type of nanocellulosic material has been prepared by high-pressure homogenization of carboxymethylated cellulose fibers followed by ultrasonication and centrifugation. This material had a cylindrical cross-section as shown by transmission electron microscopy with a diameter of 5-15 nm and a length of up to 1 microm. Calculations, using the Poisson-Boltzmann equation, showed that the surface potential was between 200 and 250 mV, depending on the pH, the salt concentration, and the size of the fibrils. They also showed that the carboxyl groups on the surface of the nanofibrils are not fully dissociated until the pH has reached pH = approximately 10 in deionized water. Calculations of the interaction between the fibrils using the Derjaguin-Landau-Verwey-Overbeek theory and assuming a cylindrical geometry indicated that there is a large electrostatic repulsion between these fibrils, provided the carboxyl groups are dissociated. If the pH is too low and/or the salt concentration is too high, there will be a large attraction between the fibrils, leading to a rapid aggregation of the fibrils. It is also possible to form polyelectrolyte multilayers (PEMs) by combining different types of polyelectrolytes and microfibrillated cellulose (MFC). In this study, silicon oxide surfaces were first treated with cationic polyelectrolytes before the surfaces were exposed to MFC. The build-up of the layers was monitored with ellipsometry, and they show that it is possible to form very well-defined layers by combinations of MFC and different types of polyelectrolytes and different ionic strengths of the solutions during the adsorption of the polyelectrolyte. A polyelectrolyte with a three-dimensional structure leads to the build-up of thick layers of MFC, whereas the use of a highly charged linear polyelectrolyte leads to the formation of thinner layers of MFC. An increase in the salt concentration during the adsorption of the polyelectrolyte results in the formation of thicker layers of MFC, indicating that the structure of the adsorbed polyelectrolyte has a large influence on the formation of the MFC layer. The films of polyelectrolytes and MFC were so smooth and well-defined that they showed clearly different interference colors, depending on the film thickness. A comparison between the thickness of the films, as measured with ellipsometry, and the thickness estimated from their colors showed good agreement, assuming that the films consisted mainly of solid cellulose with a refractive index of 1.53. Carboxymethylated MFC is thus a new type of nanomaterial that can be combined with oppositely charged polyelectrolytes to form well-defined layers that may be used to form, for example, new types of sensor materials.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Fuzzy Nanoassemblies: Toward Layered Polymeric Multicomposites
Decher, G. (1997) · Science · doi:10.1126/science.277.5330.1232 · Cited by 10,054
Self-citationDecher, G., Hong, J. D., & Schmitt, J. (1992) · Thin Solid Films · doi:10.1016/0040-6090(92)90417-a · Cited by 2,821
Self-citationPääkkö, M., Ankerfors, M., Kosonen, H., Nykänen, A., Ahola, S., Österberg, M., Ruokolainen, J., Laine, J., Larsson, P. T., Ikkala, O., et al. (2007) · Biomacromolecules · doi:10.1021/bm061215p · Cited by 1,962
Self-citationNovel Hollow Polymer Shells by Colloid-Templated Assembly of Polyelectrolytes
Donath, E., Sukhorukov, G. B., Caruso, F., Davis, S. A., & Möhwald, H. (1998) · Angewandte Chemie International Edition · doi:10.1002/(sici)1521-3773(19980904)37:16<2201::aid-anie2201>3.0.co;2-e · Cited by 1,861
Saito, T., Nishiyama, Y., Putaux, J.-L., Vignon, M., & Isogai, A. (2006) · Biomacromolecules · doi:10.1021/bm060154s · Cited by 1,796
Theory of polyelectrolytes in solutions and at surfaces
DOBRYNIN, A., & RUBINSTEIN, M. (2005) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2005.07.006 · Cited by 1,539
Biomedical Applications of Layer‐by‐Layer Assembly: From Biomimetics to Tissue Engineering
Tang, Z., Wang, Y., Podsiadlo, P., & Kotov, N. A. (2006) · Advanced Materials · doi:10.1002/adma.200600113 · Cited by 1,302
Multilayers of colloidal particles
Iler, R. K. (1966) · Journal of Colloid and Interface Science · doi:10.1016/0095-8522(66)90018-3 · Cited by 1,261
Form and Function in Multilayer Assembly: New Applications at the Nanoscale
Hammond, P. T. (2004) · Advanced Materials · doi:10.1002/adma.200400760 · Cited by 1,251
Bertrand, P., Jonas, A., Laschewsky, A., & Legras, R. (2000) · Macromolecular Rapid Communications · doi:10.1002/(sici)1521-3927(20000401)21:7<319::aid-marc319>3.0.co;2-7 · Cited by 1,213
Cited by
Nanocelluloses: A New Family of Nature‐Based Materials
Klemm, D., Kramer, F., Moritz, S., Lindström, T., Ankerfors, M., Gray, D., & Dorris, A. (2011) · Angewandte Chemie International Edition · doi:10.1002/anie.201001273 · Cited by 4,465
Self-citationTEMPO-oxidized cellulose nanofibers
Isogai, A., Saito, T., & Fukuzumi, H. (2011) · Nanoscale · doi:10.1039/c0nr00583e · Cited by 3,179
Markstedt, K., Mantas, A., Tournier, I., Martínez Ávila, H., Hägg, D., & Gatenholm, P. (2015) · Biomacromolecules · doi:10.1021/acs.biomac.5b00188 · Cited by 1,528
Cellulose Nanopaper Structures of High Toughness
Henriksson, M., Berglund, L. A., Isaksson, P., Lindström, T., & Nishino, T. (2008) · Biomacromolecules · doi:10.1021/bm800038n · Cited by 1,299
Self-citationPolylactide (PLA)-based nanocomposites
Raquez, J.-M., Habibi, Y., Murariu, M., & Dubois, P. (2013) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2013.05.014 · Cited by 1,209
Current characterization methods for cellulose nanomaterials
Foster, E. J., Moon, R. J., Agarwal, U. P., Bortner, M. J., Bras, J., Camarero-Espinosa, S., Chan, K. J., Clift, M. J. D., Cranston, E. D., Eichhorn, S. J., et al. (2018) · Chemical Society Reviews · doi:10.1039/c6cs00895j · Cited by 1,021
Cellulosic nanocomposites: a review
(2008) · BioResources · doi:10.15376/biores.3.3.929-980 · Cited by 901
Recent advances in surface-modified cellulose nanofibrils
Rol, F., Belgacem, M. N., Gandini, A., & Bras, J. (2019) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2018.09.002 · Cited by 698
Nanofibrillated Cellulose Surface Modification: A Review
Missoum, K., Belgacem, M., & Bras, J. (2013) · Materials · doi:10.3390/ma6051745 · Cited by 658
Structure and properties of the cellulose microfibril
Nishiyama, Y. (2009) · Journal of Wood Science · doi:10.1007/s10086-009-1029-1 · Cited by 567
Nanocellulose in Thin Films, Coatings, and Plies for Packaging Applications: A Review
Hubbe, M. A., Ferrer, A., Tyagi, P., Yin, Y., Salas, C., Pal, L., & Rojas, O. J. (2017) · BioResources · doi:10.15376/biores.12.1.2143-2233 · Cited by 508
Olivera, S., Muralidhara, H. B., Venkatesh, K., Guna, V. K., Gopalakrishna, K., & Kumar K., Y. (2016) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2016.08.017 · Cited by 447
Ghanadpour, M., Carosio, F., Larsson, P. T., & Wågberg, L. (2015) · Biomacromolecules · doi:10.1021/acs.biomac.5b01117 · Cited by 435
Self-citationOsong, S. H., Norgren, S., & Engstrand, P. (2016) · Cellulose · doi:10.1007/s10570-015-0798-5 · Cited by 434
Nanocellulose in packaging: Advances in barrier layer technologies
Ferrer, A., Pal, L., & Hubbe, M. (2017) · Industrial Crops and Products · doi:10.1016/j.indcrop.2016.11.012 · Cited by 382
Materials chemistry and the futurist eco-friendly applications of nanocellulose: Status and prospect
Mishra, R. K., Sabu, A., & Tiwari, S. K. (2018) · Journal of Saudi Chemical Society · doi:10.1016/j.jscs.2018.02.005 · Cited by 382
Xie, H., Du, H., Yang, X., & Si, C. (2018) · International Journal of Polymer Science · doi:10.1155/2018/7923068 · Cited by 328
Biodegradable transparent substrates for flexible organic-light-emitting diodes
Zhu, H., Xiao, Z., Liu, D., Li, Y., Weadock, N. J., Fang, Z., Huang, J., & Hu, L. (2013) · Energy & Environmental Science · doi:10.1039/c3ee40492g · Cited by 323
Aerogels from nanofibrillated cellulose with tunable oleophobicity
Aulin, C., Netrval, J., Wågberg, L., & Lindström, T. (2010) · Soft Matter · doi:10.1039/c001939a · Cited by 306
Self-citationUnderstanding the Dispersive Action of Nanocellulose for Carbon Nanomaterials
Hajian, A., Lindström, S. B., Pettersson, T., Hamedi, M. M., & Wågberg, L. (2017) · Nano Letters · doi:10.1021/acs.nanolett.6b04405 · Cited by 293
Self-citationNyström, G., Marais, A., Karabulut, E., Wågberg, L., Cui, Y., & Hamedi, M. M. (2015) · Nature Communications · doi:10.1038/ncomms8259 · Cited by 280
Self-citationNanofibrillated cellulose as an additive in papermaking process: A review
Boufi, S., González, I., Delgado-Aguilar, M., Tarrès, Q., Pèlach, M. À., & Mutjé, P. (2016) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2016.07.117 · Cited by 265
Aulin, C., Salazar-Alvarez, G., & Lindström, T. (2012) · Nanoscale · doi:10.1039/c2nr31726e · Cited by 260
Self-citationIsogai, A., & Zhou, Y. (2019) · Current Opinion in Solid State and Materials Science · doi:10.1016/j.cossms.2019.01.001 · Cited by 253
Preparation of cellulose nanomaterials via cellulose oxalates
Henschen, J., Li, D., & Ek, M. (2019) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2019.02.056 · Cited by 135
Metadata
- Authors
- Wågberg, L., Decher, G., Norgren, M., Lindström, T., Ankerfors, M., & Axnäs, K.
- Venue
- Langmuir
- Publisher
- American Chemical Society (ACS)
- Published
- 2008-01-11
- Volume
- 24
- Issue
- 3
- Pages
- 784-795
- ISSN
- 0743-7463 (ISSN-L)
- 1520-5827
- OpenAlex
- W1976745823
- Cited by
- 867
- References
- 28
- FWCI
- 10.63
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.