Strained Lattice with Persistent Atomic Order in Pt3Fe2 Intermetallic Core–Shell Nanocatalysts
The DOI matches its Crossref record; 31 of the 32 references it cites were found in a registry or an index.
Abstract
Fine-tuning nanocatalysts to enhance their catalytic activity and durability is crucial to commercialize proton exchange membrane fuel cells. The structural ordering and time evolution of ordered Pt3Fe2 intermetallic core-shell nanocatalysts for the oxygen reduction reaction that exhibit increased mass activity (228%) and an enhanced catalytic activity (155%) compared to Pt/C has been quantified using aberration-corrected scanning transmission electron microscopy. These catalysts were found to exhibit a static core-dynamic shell regime wherein, despite treating over 10,000 cycles, there is negligible decrease (9%) in catalytic activity and the ordered Pt3Fe2 core remained virtually intact while the Pt shell suffered a continuous enrichment. The existence of this regime was further confirmed by X-ray diffraction and the compositional analyses using energy-dispersive spectroscopy. With atomic-scale two-dimensional (2-D) surface relaxation mapping, we demonstrate that the Pt atoms on the surface are slightly relaxed with respect to bulk. The cycled nanocatalysts were found to exhibit a greater surface relaxation compared to noncycled catalysts. With 2-D lattice strain mapping, we show that the particle was about -3% strained with respect to pure Pt. While the observed enhancement in their activity is ascribed to such a strained lattice, our findings on the degradation kinetics establish that their extended catalytic durability is attributable to a sustained atomic order.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“To obtain chemically ordered Pt-Fe alloy phases, an annealing step was required at 800 °C under 8 vol % H 2 /Ar.”
In the citing paper
“Later, Botton's group developed a wet impregnation technique to synthesize a new structurally ordered intermetallic core-shell Pt 3 Fe 2 /C alloy catalysts, with an ordered Pt 3 Fe 2 core encapsulated within a bilayer Pt-rich shell.424”
In the citing paper
“Note that the core of the Pt3Fe@Pt NPs induces compressive strain in the Pt atomic shell, which can modulate the electronic structure of Pt and thereby enhance its electrocatalytic activity.34,35”
From Tuning the local environment of atomic Pt shells of Pt 3 Fe@Pt nanoparticles enables energy-saving hydrogen production (2026) · cites this paper as [34]
Citations
Cites
Electrochemical Methods: Fundamentals and Applications
Bard, A. J., & Faulkner, L. R. (1980) · Cited by 22,821
Monodisperse FePt Nanoparticles and Ferromagnetic FePt Nanocrystal Superlattices
Sun, S., Murray, C. B., Weller, D., Folks, L., & Moser, A. (2000) · Science · doi:10.1126/science.287.5460.1989 · Cited by 6,137
Electrocatalyst approaches and challenges for automotive fuel cells
Debe, M. K. (2012) · Nature · doi:10.1038/nature11115 · Cited by 5,885 · cited 2×
“(ORR) occurring at the cathode in a proton exchange membrane fuel cell (PEMFC).(3)”
BackgroundGasteiger, H. A., Kocha, S. S., Sompalli, B., & Wagner, F. T. (2005) · Applied Catalysis B: Environmental · doi:10.1016/j.apcatb.2004.06.021 · Cited by 4,876 · cited 1×
“to be an unrealistic choice owing to their exceedingly high costs.(3,4) Hence, various new catalyst designs are in vogue, with the intention to achieve higher activities”
BackgroundImproved Oxygen Reduction Activity on Pt 3 Ni(111) via Increased Surface Site Availability
Stamenkovic, V. R., Fowler, B., Mun, B. S., Wang, G., Ross, P. N., Lucas, C. A., & Marković, N. M. (2007) · Science · doi:10.1126/science.1135941 · Cited by 4,421 · cited 2×
“exists a poor d-overlap among Pt atoms, leading to decreased catalytic activity compared to that of bimetallic regimes.(15) 17”
BackgroundTrends in electrocatalysis on extended and nanoscale Pt-bimetallic alloy surfaces
Stamenkovic, V. R., Mun, B. S., Arenz, M., Mayrhofer, K. J. J., Lucas, C. A., Wang, G., Ross, P. N., & Markovic, N. M. (2007) · Nature Materials · doi:10.1038/nmat1840 · Cited by 3,252
Alloys of platinum and early transition metals as oxygen reduction electrocatalysts
Greeley, J., Stephens, I. E. L., Bondarenko, A. S., Johansson, T. P., Hansen, H. A., Jaramillo, T. F., Rossmeisl, J., Chorkendorff, I., & Nørskov, J. K. (2009) · Nature Chemistry · doi:10.1038/nchem.367 · Cited by 3,203
Enhancement of the Electroreduction of Oxygen on Pt Alloys with Fe, Ni, and Co
Toda, T., Igarashi, H., Uchida, H., & Watanabe, M. (1999) · Journal of The Electrochemical Society · doi:10.1149/1.1392544 · Cited by 1,336
Instability of Supported Platinum Nanoparticles in Low-Temperature Fuel Cells
Shao-Horn, Y., Sheng, W. C., Chen, S., Ferreira, P. J., Holby, E. F., & Morgan, D. (2007) · Topics in Catalysis · doi:10.1007/s11244-007-9000-0 · Cited by 939 · cited 1×
“Such an increase in their sizes is due to enrichment in the nanocatalyst shell thickness, possibly by Ostwald ripening.(28) However, it is important to notice here that the increase is small compared to previous Pt Fe catalyst designs,(18) owing to controlled degradation”
ResultWang, J. X., Inada, H., Wu, L., Zhu, Y., Choi, Y., Liu, P., Zhou, W.-P., & Adzic, R. R. (2009) · Journal of the American Chemical Society · doi:10.1021/ja9067645 · Cited by 719
Size-Selected Synthesis of PtRu Nano-Catalysts: Reaction and Size Control Mechanism
Bock, C., Paquet, C., Couillard, M., Botton, G. A., & MacDougall, B. R. (2004) · Journal of the American Chemical Society · doi:10.1021/ja0495819 · Cited by 699 · cited 1×
“Pt/C were prepared as a first step by employing the polyol method reported previously.(30) First, 500 mg of 20 wt % precursors was ultrasonicated for about 1.”
MethodSelf-citationTuning the Activity of Pt(111) for Oxygen Electroreduction by Subsurface Alloying
Stephens, I. E. L., Bondarenko, A. S., Perez-Alonso, F. J., Calle-Vallejo, F., Bech, L., Johansson, T. P., Jepsen, A. K., Frydendal, R., Knudsen, B. P., Rossmeisl, J., et al. (2011) · Journal of the American Chemical Society · doi:10.1021/ja111690g · Cited by 526
Mukerjee, S., Srinivasan, S., Soriaga, M. P., & McBreen, J. (1995) · The Journal of Physical Chemistry · doi:10.1021/j100013a032 · Cited by 439 · cited 1×
“duce compressive strain in the lattice by introducing 3d transition metals (M = Ni, Co, Fe, Cu, Cr).(5) 10 Thus far, two prominent regimes are identifiable: the alloyed Pt M systems mainly leading to bimetallic(11) and ternary(12) nanocatalysts and, a core shell(13)”
BackgroundSize and shape effects on the order–disorder phase transition in CoPt nanoparticles
Alloyeau, D., Ricolleau, C., Mottet, C., Oikawa, T., Langlois, C., Le Bouar, Y., Braidy, N., & Loiseau, A. (2009) · Nature Materials · doi:10.1038/nmat2574 · Cited by 402
Effects of elastic anisotropy on strain distributions in decahedral gold nanoparticles
Johnson, C. L., Snoeck, E., Ezcurdia, M., Rodríguez-González, B., Pastoriza-Santos, I., Liz-Marzán, L. M., & Hÿtch, M. J. (2008) · Nature Materials · doi:10.1038/nmat2083 · Cited by 324
Electrocatalytic Activity Studies of Select Metal Surfaces and Implications in Li-Air Batteries
Lu, Y.-C., Gasteiger, H. A., Crumlin, E., McGuire, R., & Shao-Horn, Y. (2010) · Journal of The Electrochemical Society · doi:10.1149/1.3462981 · Cited by 275 · cited 1×
“of increasing their surface to volume ratios to reduce catalyst loading and, hence, mitigate the cost.(1,2) Currently, there is a great interest in devising such nanocatalysts to accelerate the oxygen reduction reaction”
BackgroundXiong, L., & Manthiram, A. (2005) · Journal of The Electrochemical Society · doi:10.1149/1.1862256 · Cited by 238
Nanostructured catalysts in fuel cells
Zhong, C.-J., Luo, J., Fang, B., Wanjala, B. N., Njoki, P. N., Loukrakpam, R., & Yin, J. (2010) · Nanotechnology · doi:10.1088/0957-4484/21/6/062001 · Cited by 198
Ostwald Ripening in Nanoalloys: When Thermodynamics Drives a Size-Dependent Particle Composition
Alloyeau, D., Prévot, G., Bouar, Y. L., Oikawa, T., Langlois, C., Loiseau, A., & Ricolleau, C. (2010) · Physical Review Letters · doi:10.1103/physrevlett.105.255901 · Cited by 150
Lattice Strain Distributions in Individual Dealloyed Pt–Fe Catalyst Nanoparticles
Gan, L., Yu, R., Luo, J., Cheng, Z., & Zhu, J. (2012) · The Journal of Physical Chemistry Letters · doi:10.1021/jz300192b · Cited by 140 · cited 1×
“These catalysts exhibit the highest activity and extended durability compared to all other Pt Fe designs reported in the literature.(18,23,24) While a comparative discussion on catalyst synthesis, electrochemical measurements, and XRD analysis of these catalysts with other Pt Fe designs is presented in a recent articl…”
BackgroundAtomistic origin of lattice strain on stiffness of nanoparticles
Ouyang, G., Zhu, W., Sun, C., Zhu, Z., & Liao, S. (2010) · Physical Chemistry Chemical Physics · doi:10.1039/b919982a · Cited by 117
Preparation and characterization of carbon-supported PtVFe electrocatalysts
Luo, J., Kariuki, N. N., Han, L., Wang, L., Zhong, C., & He, T. (2006) · Electrochimica Acta · doi:10.1016/j.electacta.2006.01.019 · Cited by 109
Chen, H., Yu, Y., Xin, H. L., Newton, K. A., Holtz, M. E., Wang, D., Muller, D. A., Abruña, H. D., & DiSalvo, F. J. (2013) · Chemistry of Materials · doi:10.1021/cm303489z · Cited by 98 · cited 1×
“XRD analysis on the annealed samples revealed a slight increase in thecrystallite sizepostannealing,which is known to be due to possible particle sintering.(18,25) We also found that the amount of Fe salt added primarily dictates the stoichiometry of ordered cores being formed.”
BackgroundSurface effects of ordering in binary alloys
Vasiliev, M. A. (1997) · Journal of Physics D Applied Physics · doi:10.1088/0022-3727/30/22/002 · Cited by 87 · cited 1×
“org 6104 aggregation upon annealing(18) 20 and partly because of the model-based calculations on the Pt Fe system predicting a monotonically decreasing Pt profile in the subsurface layers as opposed to Pt Co and Pt Ni that were reported to be oscillatory.(15,21,22) Here we demonstrate a new intermetallic core shell (I…”
BackgroundSupported sub-5nm Pt–Fe intermetallic compounds for electrocatalytic application
Li, X., An, L., Wang, X., Li, F., Zou, R., & Xia, D. (2012) · Journal of Materials Chemistry · doi:10.1039/c2jm16504j · Cited by 72 · cited 2×
“XRD analysis on the annealed samples revealed a slight increase in thecrystallite sizepostannealing,which is known to be due to possible particle sintering.(18,25) We also found that the amount of Fe salt added primarily dictates the stoichiometry of ordered cores being formed.”
BackgroundOrdered alloy formation for Pt3Fe/C, PtFe/C and Pt5.75Fe5.75Cuy/CO2-reduction electro-catalysts
Chen, L., Bock, C., Mercier, P. H. J., & MacDougall, B. R. (2012) · Electrochimica Acta · doi:10.1016/j.electacta.2012.05.103 · Cited by 52
Self-citationYu, T. H., Sha, Y., Merinov, B. V., & Goddard, W. A. (2010) · The Journal of Physical Chemistry C · doi:10.1021/jp1024735 · Cited by 49 · cited 2×
“0691 g of Fe salt resulted in a Pt3Fe ordered core, the Pt was found to exhibit poorer surface segregation, in turn leading to a significant decrease in catalyst performance.(19,22,24)”
Background(2011) · Nature Materials · doi:10.1038/nmat3221 · Cited by 38
Compositional and Morphological Changes of Ordered PtxFey/C Oxygen Electroreduction Catalysts
Chen, L., Chan, M. C. Y., Nan, F., Bock, C., Botton, G. A., Mercier, P. H. J., & MacDougall, B. R. (2013) · ChemCatChem · doi:10.1002/cctc.201200614 · Cited by 21 · cited 1×
“0691 g of Fe salt resulted in a Pt3Fe ordered core, the Pt was found to exhibit poorer surface segregation, in turn leading to a significant decrease in catalyst performance.(19,22,24)”
BackgroundSelf-citationChan, M. C. Y., Chen, L., Nan, F., Britten, J. F., Bock, C., & Botton, G. A. (2012) · Nanoscale · doi:10.1039/c2nr31509b · Cited by 10 · cited 2×
“These catalysts exhibit the highest activity and extended durability compared to all other Pt Fe designs reported in the literature.(18,23,24) While a comparative discussion on catalyst synthesis, electrochemical measurements, and XRD analysis of these catalysts with other Pt Fe designs is presented in a recent articl…”
BackgroundSelf-citationTaufour, V., Aoki, D., Knebel, G., & Flouquet, J. (2010) · Physical Review Letters · Cited by 9
Cited by
Wang, Y.-J., Zhao, N., Fang, B., Li, H., Bi, X. T., & Wang, H. (2015) · Chemical Reviews · doi:10.1021/cr500519c · Cited by 1,267
Core–shell nanoparticles: synthesis and applications in catalysis and electrocatalysis
Gawande, M. B., Goswami, A., Asefa, T., Guo, H., Biradar, A. V., Peng, D.-L., Zboril, R., & Varma, R. S. (2015) · Chemical Society Reviews · doi:10.1039/c5cs00343a · Cited by 1,143
Electrochemical Activation of CO2 through Atomic Ordering Transformations of AuCu Nanoparticles
Kim, D., Xie, C., Becknell, N., Yu, Y., Karamad, M., Chan, K., Crumlin, E. J., Nørskov, J. K., & Yang, P. (2017) · Journal of the American Chemical Society · doi:10.1021/jacs.7b03516 · Cited by 680
Organic Phase Syntheses of Magnetic Nanoparticles and Their Applications
Wu, L., Mendoza-Garcia, A., Li, Q., & Sun, S. (2016) · Chemical Reviews · doi:10.1021/acs.chemrev.5b00687 · Cited by 601
Intermetallic Nanocrystals: Syntheses and Catalytic Applications
Yan, Y., Du, J. S., Gilroy, K. D., Yang, D., Xia, Y., & Zhang, H. (2017) · Advanced Materials · doi:10.1002/adma.201605997 · Cited by 550
Metadata
- Authors
- Prabhudev, S., Bugnet, M., Bock, C., & Botton, G. A.
- Affiliations
- McMaster University (CA)
- National Research Council Canada (CA)
- Corresponding author
- Botton, Gianluigi A.
- Venue
- ACS Nano
- Publisher
- American Chemical Society (ACS)
- Published
- 2013-06-27
- Volume
- 7
- Issue
- 7
- Pages
- 6103-6110
- ISSN
- 1936-0851 (ISSN-L)
- 1936-086X
- OpenAlex
- W2326057121
- Cited by
- 101
- References
- 32
- Citations by year
- 2026: 3 · 2025: 2 · 2024: 5 · 2023: 4 · 2022: 7 · 2021: 4 · 2020: 7 · 2019: 8 · 2018: 11 · 2017: 9 · 2016: 14 · 2015: 21 · 2014: 5 · 2013: 1
- FWCI
- 4.97
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- ACS Nano (publishedVersion)
- PubMed (publishedVersion)
- HAL (submittedVersion)
- NPARC (submittedVersion)
- Topics
- Physical Sciences › Energy › Renewable Energy, Sustainability and the Environment › Electrocatalysts for Energy Conversion
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Fuel Cells and Related Materials
- Physical Sciences › Materials Science › Materials Chemistry › Catalytic Processes in Materials Science
- Keywords
- core-shell nanocatalysts, oxygen reduction reaction, proton exchange membrane fuel cells, lattice strain, surface relaxation, atomic ordering, catalyst stability, degradation kinetics, mass activity, Pt/C comparison, aberration-corrected scanning transmission electron microscopy
- MeSH terms
- Alloys, Catalysis, Iron, Materials Testing, Platinum, Tensile Strength, Metal Nanoparticles, Elastic Modulus, Nanopores
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.