Tuning the local environment of atomic Pt shells of Pt 3 Fe@Pt nanoparticles enables energy-saving hydrogen production
The DOI matches its Crossref record; 82 of the 82 references it cites were found in a registry or an index; 11 of the 60 sources its claims cite were checked for support.
Abstract
Energy-saving hydrogen production is realized via coupling with the methanol oxidation reaction endowed with superior CO tolerance.
Overview
CoChat Summary
TL;DR
Core–shell Pt3Fe@Pt nanoparticles (~4.25 nm, ~2–3 atomic Pt shell layers) decorated with abundant O-bridged Fe single atoms on carbon were synthesized, tuning the local environment of the Pt shell. The catalyst delivers enhanced alkaline methanol oxidation (anti-CO poisoning) and alkaline hydrogen evolution, enabling MOR//HER-coupled water splitting at 0.574 V at 10 mA cm⁻² with ~100% Faradaic efficiency for H2.
Key findings
- The CS Pt3Fe@Pt NP–O–A–Fe SA/C catalyst has an ECSA_CO of 89.14 m² g_Pt⁻¹ versus 39.02 m² g_Pt⁻¹ for commercial Pt/C, and its acidic CO stripping onset/peak potentials (0.620 V / 0.732 V) are more negative than Pt/C's (0.757 V / 0.865 V), indicating stronger CO removal.
- For alkaline MOR, mass activity is 5.92 A mg_Pt⁻¹ and specific activity 6.64 mA cm⁻² — 3.79× and 1.72× higher than commercial Pt/C (1.56 A mg_Pt⁻¹, 3.86 mA cm⁻²); onset potential is 0.40 V vs 0.46 V. After CO-flux testing, MA recovered to 6.22 A mg_Pt⁻¹, higher than before the test.
- For alkaline HER, η10 is 10 mV versus 40 mV for Pt/C (and 19 mV for the prior HDS Pt3Fe@Pt–O–Fe-SA NP/C catalyst); MA at −0.05 V is 1.31 A mg_Pt⁻¹ (3.74× Pt/C's 0.35) and Tafel slope is 33.30 mV dec⁻¹ versus 70.12 mV dec⁻¹.
- In a two-electrode MOR//HER cell, 10 mA cm⁻² is reached at 0.574 V, 1.2 V lower than the OER//HER configuration (1.774 V), with Faradaic efficiency for H2 near 100% over three repeated tests. After 5000 ADT cycles η10 shifts only 8 mV (vs ~16 mV for Pt/C), and 86.79% of initial current is retained after 18000 s (vs 41.19% decay for Pt/C).
Methods
- Synthesis: PANI-Fe(III) aerogels dispersed in water with K2PtCl4 (14.45 mM), stirred at 70 °C for 12 h, freeze-dried, pyrolyzed at 900 °C for 2 h in flowing Ar (10 °C min⁻¹), then acid-treated in 0.5 M H2SO4 at 80 °C for 8 h. The optimal sample used 96 mM Fe³⁺ (screened across 48–120 mM).
- Characterization: TEM/HR-TEM, AC-HAADF-STEM and EDS mapping/line scans, XRD, Raman, CO stripping voltammetry, XPS (O 1s, Pt 4f), N2 adsorption–desorption.
- Electrochemistry: alkaline MOR in N2-saturated 1.0 M KOH + 1.0 M CH3OH; alkaline HER in N2-saturated 1.0 M KOH; EIS, chronoamperometry, ADTs, and a symmetric two-electrode cell with the catalyst as both anode and cathode (MOR//HER vs OER//HER), with H2 quantified by GC.
Limitations
- The paper states no explicit limitations section; the authors note that at the highest Fe³⁺ concentration (120 mM) Pt shell active sites become highly covered by O-bridged Fe SAs, which "may impair their catalytic activity," making 96 mM the optimum.
- Evident from the text: performance benchmarking is against commercial Pt/C and the authors' own prior HDS catalyst, with broader comparisons relegated to supplementary tables; the local acidic environment during HER is inferred from structural analogy and operando Raman data placed in the SI; and all measurements are laboratory-scale half-cell and two-electrode tests, with no durability or scale-up data beyond 5000 ADT cycles and 18000 s chronoamperometry.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
8 Valid · 0 Not valid · 11 Not checked · 46 Own results and interpretations
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“but also enhances the alkaline hydrogen evolution reaction (HER) performance by creating an optimally local acidic environment near the Pt shells.”
- Also stated in: § Introduction · plain
“but also enhances the alkaline HER performance by creating an optimally local acidic environment near the Pt shells (Scheme 1c).32”
What the sources say
- Partly supportedcites [32] sourceExperimental — accuracy not yet measured
The Discussion and Results (Density functional theory calculations) say that a local acid-like environment around Pt promotes alkaline HER. But the source studies Pt nanoparticles on oxygen-vacancy-rich MgO, not atomic Pt shells tuned by O-bridged Fe single atoms; it also does not establish that the environment is optimal. (LLM, conf=0.88)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Also stated in: § Introduction · plain
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Currently, Pt-based electrocatalysts are still recognized as the most effective catalysts for both alkaline HER and alkaline MOR.16,20–22”
What the sources say
- Partly supportedcites [16] sourceExperimental — accuracy not yet measured
The Introduction says Pt(Pd)-based catalysts activate alkaline MOR at low voltage and Pt single atoms have excellent HER activity. The Results and Discussion report that this particular Pt–Pd–hydroxide catalyst outperforms tested benchmarks for both reactions. Those findings support the importance of Pt-based catalysts, but not the broader claim that the class is recognized as the most effective for both alkaline HER and MOR. (LLM, conf=0.83)
- Not checked — no full text of the sourcecites [20] source
- Not checked — no full text of the sourcecites [21] source
- Not checked — no full text of the sourcecites [22] source
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“The alkaline HER process catalyzed by the as-prepared CS Pt3Fe@Pt NP–O–A–Fe SA/C catalyst may follow the Volmer-Tafel mechanism that usually occurs during acidic HER.”
What the sources say
- Not checked — no full text of the sourcecites [30] source
- Partly supportedcites [32] sourceExperimental — accuracy not yet measured
The Results (Density functional theory calculations; page unavailable) describe an acid-like environment during alkaline HER and propose a Tafel step for Pt/MgO. But the paper does not study the named CS Pt3Fe@Pt NP–O–A–Fe SA/C catalyst, and the Results (Electrocatalytic performance toward HER; page unavailable) identify Pt/MgO’s kinetics as Volmer–Heyrovsky, not Volmer–Tafel. It therefore does not establish the proposed mechanism for the citing paper’s catalyst. (LLM, conf=0.86)
- Partly supportedcites [82] sourceExperimental — accuracy not yet measured
The Electrochemical HER Performance passage (indexed under Abstract; page unavailable) says the Tafel slope suggests a Volmer–Tafel mechanism for Ru/Fe–N–C in alkaline electrolyte. It does not study the claimed CS Pt3Fe@Pt NP–O–A–Fe SA/C catalyst or say that this mechanism usually occurs during acidic HER. (LLM, conf=0.88)
hedgedstates a possible cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“the average lattice spacing is measured to be about 0.224 nm, which lies between the lattice spacing of the Pt3Fe (111) plane (0.223 nm) and that of the Pt (111) plane (0.226 nm).”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“In this work, small-sized, core–shell structured Pt3Fe nanoparticles (NPs) with a Pt shell thickness of ∼2–3 atomic layers were successfully fabricated.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
32 more claims
Create a free account to see all 65 claims and every source verdict.
- Probably not a substantial claim. 4
- It may state two separate claims as one. 23
- The quote only partly states this claim. 1
Citations
Cites
Wang, D., Xin, H. L., Hovden, R., Wang, H., Yu, Y., Muller, D. A., DiSalvo, F. J., & Abruña, H. D. (2013) · Nature Materials · doi:10.1038/nmat3458 · Cited by 2,082
Water electrolysis based on renewable energy for hydrogen production
Chi, J., & Yu, H. (2018) · Chinese Journal of Catalysis · doi:10.1016/s1872-2067(17)62949-8 · Cited by 1,493
Enhancing Electrocatalytic Water Splitting by Strain Engineering
You, B., Tang, M. T., Tsai, C., Abild‐Pedersen, F., Zheng, X., & Li, H. (2019) · Advanced Materials · doi:10.1002/adma.201807001 · Cited by 793
Sun, H., Xu, X., Kim, H., Jung, W., Zhou, W., & Shao, Z. (2023) · ENERGY & ENVIRONMENTAL MATERIALS · doi:10.1002/eem2.12441 · Cited by 601
Tantalum-stabilized ruthenium oxide electrocatalysts for industrial water electrolysis
Zhang, J., Fu, X., Kwon, S., Chen, K., Liu, X., Yang, J., Sun, H., Wang, Y., Uchiyama, T., Uchimoto, Y., et al. (2025) · Science · doi:10.1126/science.ado9938 · Cited by 494
Self-citationZheng, Y.-R., Wu, P., Gao, M.-R., Zhang, X.-L., Gao, F.-Y., Ju, H.-X., Wu, R., Gao, Q., You, R., Huang, W.-X., et al. (2018) · Nature Communications · doi:10.1038/s41467-018-04954-7 · Cited by 460
Progress in Hydrogen Production Coupled with Electrochemical Oxidation of Small Molecules
Wang, T., Cao, X., & Jiao, L. (2022) · Angewandte Chemie International Edition · doi:10.1002/anie.202213328 · Cited by 410
Tan, H., Tang, B., Lu, Y., Ji, Q., Lv, L., Duan, H., Li, N., Wang, Y., Feng, S., Li, Z., et al. (2022) · Nature Communications · doi:10.1038/s41467-022-29710-w · Cited by 390
A comprehensive review of recent advances in alkaline water electrolysis for hydrogen production
Sebbahi, S., Assila, A., Alaoui Belghiti, A., Laasri, S., Kaya, S., Hlil, E. K., Rachidi, S., & Hajjaji, A. (2024) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2024.07.428 · Cited by 387
Wang, X., Xu, C., Jaroniec, M., Zheng, Y., & Qiao, S.-Z. (2019) · Nature Communications · doi:10.1038/s41467-019-12773-7 · Cited by 386
Self-citation
Research works printed but not linked: 1
- Liu, 2020, Research, 2020, 9068270
Metadata
- Authors
- Li, S., Xu, Q., Sun, B., Liu, X., Tian, H., Wang, X., & Xia, H.
- Affiliations
- Shandong University (CN)
- State Key Laboratory of Silicon Materials (CN)
- Venue
- Journal of Materials Chemistry A
- Publisher
- Royal Society of Chemistry (RSC)
- Published
- 2026
- Volume
- 14
- Issue
- 36
- Pages
- 23782-23792
- ISSN
- 2050-7488 (ISSN-L)
- 2050-7496
- OpenAlex
- W7156242901
- Semantic Scholar
- 11ecd705ca1a4aac90fd9419f70cdd25bb4e41e8
- Cited by
- 0
- References
- 82
- FWCI
- 0.00
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Journal of Materials Chemistry A (publishedVersion)
- Funders
- National Natural Science Foundation of China (22072076, 22472086)
- Shandong University
- Topics
- Physical Sciences › Energy › Renewable Energy, Sustainability and the Environment › Electrocatalysts for Energy Conversion
- Physical Sciences › Materials Science › Materials Chemistry › Catalytic Processes in Materials Science
- Physical Sciences › Chemical Engineering › Catalysis › Catalysts for Methane Reforming
- Keywords
- platinum nanoparticles, methanol oxidation, CO tolerance, hydrogen production, electrocatalysis, energy-saving hydrogen production
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-11, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-11 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Tuning the local environment of atomic Pt shells of Pt 3 Fe@Pt nanoparticles enables energy-saving hydrogen production. https://app.cochat.ai/papers/10.1039/d6ta01696k
- The paper
- Li, S., Xu, Q., Sun, B., Liu, X., Tian, H., Wang, X., & Xia, H. (2026). Tuning the local environment of atomic Pt shells of Pt 3 Fe@Pt nanoparticles enables energy-saving hydrogen production. Journal of Materials Chemistry A. https://doi.org/10.1039/d6ta01696k
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.