The DOI matches its Crossref record; 41 of the 41 references it cites were found in a registry or an index.
Frictional slip of granite at hydrothermal conditions
Abstract
Sliding on faults in much of the continental crust likely occurs at hydrothermal conditions, i.e., at elevated temperature and elevated pressure of aqueous pore fluids, yet there have been few relevant laboratory studies. To measure the strength, sliding behavior, and friction constitutive properties of faults at hydrothermal conditions, we slid laboratory granite faults containing a layer of granite powder (simulated gouge). Velocity stepping experiments were performed at temperatures of 23° to 600°C, pore fluid pressures P H 2 O of 0 (“dry”) and 100 MPa (“wet”), effective normal stress of 400 MPa, and sliding velocities V of 0.01 to 1 μm/s (0.32 to 32 m/yr). Conditions were similar to those in earlier tests on dry granite to 845°C by Lockner et al. (1986). The mechanical results define two regimes. The first regime includes dry granite up to at least 845° and wet granite below 250°C. In this regime the coefficient of friction is high (μ = 0.7 to 0.8) and depends only modestly on temperature, slip rate, and PH 2 O. The second regime includes wet granite above ∼350°C. In this regime friction decreases considerably with increasing temperature (temperature weakening) and with decreasing slip rate (velocity strengthening). These regimes correspond well to those identified in sliding tests on ultrafine quartz. We infer that one or more fluid‐assisted deformation mechanisms are activated in the second, hydrothermal, regime and operate concurrently with cataclastic flow. Slip in the first (cool and/or dry) regime is characterized by pervasive shearing and particle size reduction. Slip in the second (hot and wet) regime is localized primarily onto narrow shear bands adjacent to the gouge‐rock interfaces. Weakness of these boundary shears may result either from an abundance of phyllosilicates preferentially aligned for easy dislocation glide, or from a dependence of strength on gouge particle size. Major features of the granite data set can be fit reasonably well by a rate‐ and temperature‐dependent, three‐regime friction constitutive model (Chester, this issue). We extrapolate the experimental data and model fit in order to estimate steady state shear strength versus depth along natural, slipping faults for sliding rates as low as 31 mm/yr. We do this for two end‐member cases. In the first case, pore pressure is assumed hydrostatic at all depths. Shallow crustal strength in this case is similar to that calculated in previous work from room temperature friction data, while at depths below about 9–13 km (depending on slip rate), strength becomes less sensitive to depth but sensitive to slip rate. In the second case, pore pressure is assumed to be near‐lithostatic at depths below ∼5 km. Strength is low at all depths in this case (<20 MPa, in agreement with observations of “weak” faults such as the San Andreas). The predicted depth of transition from velocity weakening to velocity strengthening lies at about 13 km depth for a slip rate of 31 mm/yr, in rough agreement with the seismic‐aseismic transition depth observed on mature continental faults. These results highlight the importance of fluid‐assisted deformation processes active in faults at depth and the need for laboratory studies on the roles of additional factors such as fluid chemistry, large displacements, higher concentrations of phyllosilicates, and time‐dependent fault healing.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Byerlee, J. (1978) · pure and applied geophysics · doi:10.1007/bf00876528 · Cited by 4,029
Self-citationSlip instability and state variable friction laws
Ruina, A. (1983) · Journal of Geophysical Research: Solid Earth · doi:10.1029/jb088ib12p10359 · Cited by 3,280
Modeling of rock friction: 1. Experimental results and constitutive equations
Dieterich, J. H. (1979) · Journal of Geophysical Research: Solid Earth · doi:10.1029/jb084ib05p02161 · Cited by 3,049
Limits on lithospheric stress imposed by laboratory experiments
Brace, W. F., & Kohlstedt, D. L. (1980) · Journal of Geophysical Research: Solid Earth · doi:10.1029/jb085ib11p06248 · Cited by 1,814
The kinetics of silica-water reactions
Rimstidt, J. D., & Barnes, H. L. (1980) · Geochimica et Cosmochimica Acta · doi:10.1016/0016-7037(80)90220-3 · Cited by 1,266
Stability of Steady Frictional Slipping
Rice, J. R., & Ruina, A. L. (1983) · Journal of Applied Mechanics · doi:10.1115/1.3167042 · Cited by 1,120
Crustal earthquake instability in relation to the depth variation of frictional slip properties
Tse, S. T., & Rice, J. R. (1986) · Journal of Geophysical Research: Solid Earth · doi:10.1029/jb091ib09p09452 · Cited by 950
Stress and temperature in the bending lithosphere as constrained by experimental rock mechanics
Goetze, C., & Evans, B. (1979) · Geophysical Journal International · doi:10.1111/j.1365-246x.1979.tb02567.x · Cited by 891
Heat flow and energetics of the San Andreas Fault Zone
Lachenbruch, A. H., & Sass, J. H. (1980) · Journal of Geophysical Research: Solid Earth · doi:10.1029/jb085ib11p06185 · Cited by 868
Pressure solution in nature, theory and experiment
Rutter, E. H. (1983) · Journal of the Geological Society · doi:10.1144/gsjgs.140.5.0725 · Cited by 744
Rice, J. R. (1992) · International Geophysics · doi:10.1016/s0074-6142(08)62835-1 · Cited by 659
Frictional behavior and constitutive modeling of simulated fault gouge
Marone, C., Raleigh, C. B., & Scholz, C. H. (1990) · Journal of Geophysical Research: Solid Earth · doi:10.1029/jb095ib05p07007 · Cited by 630
Continental fault structure and the shallow earthquake source
Sibson, R. H. (1983) · Journal of the Geological Society · doi:10.1144/gsjgs.140.5.0741 · Cited by 531
Constitutive Properties of Faults With Simulated Gouge
Dieterich, J. H. (2013) · Geophysical Monograph Series · doi:10.1029/gm024p0103 · Cited by 488
Creep, compaction and the weak rheology of major faults
Sleep, N. H., & Blanpied, M. L. (1992) · Nature · doi:10.1038/359687a0 · Cited by 431
Self-citationFriction, overpressure and fault normal compression
Byerlee, J. (1990) · Geophysical Research Letters · doi:10.1029/gl017i012p02109 · Cited by 396
Self-citationFault stability inferred from granite sliding experiments at hydrothermal conditions
Blanpied, M. L., Lockner, D. A., & Byerlee, J. D. (1991) · Geophysical Research Letters · doi:10.1029/91gl00469 · Cited by 363
Self-citationFluid-rock reaction weakening of fault zones
(1996) · International Journal of Rock Mechanics and Mining Sciences & Geomechanics Abstracts · doi:10.1016/0148-9062(96)89823-8 · Cited by 327
Basal slip and mechanical anisotropy of biotite
Kronenberg, A. K., Kirby, S. H., & Pinkston, J. (1990) · Journal of Geophysical Research: Solid Earth · doi:10.1029/jb095ib12p19257 · Cited by 297
Friction in faulted rock at high temperature and pressure
Stesky, R. M., Brace, W. F., Riley, D. K., & Robin, P.-Y. F. (1974) · Tectonophysics · doi:10.1016/0040-1951(74)90119-x · Cited by 292
An earthquake mechanism based on rapid sealing of faults
Blanpied, M. L., Lockner, D. A., & Byerlee, J. D. (1992) · Nature · doi:10.1038/358574a0 · Cited by 275
Self-citationStrength and anisotropy of foliated rocks with varied mica contents
Shea, W. T., & Kronenberg, A. K. (1993) · Journal of Structural Geology · doi:10.1016/0191-8141(93)90158-7 · Cited by 269
Heat flow from Cajon Pass, fault strength, and tectonic implications
Lachenbruch, A. H., & Sass, J. H. (1992) · Journal of Geophysical Research: Solid Earth · doi:10.1029/91jb01506 · Cited by 265
Tectonic stresses in the lithosphere: Constraints provided by the experimental deformation of rocks
Kirby, S. H. (1980) · Journal of Geophysical Research: Solid Earth · doi:10.1029/jb085ib11p06353 · Cited by 260
Multimechanism friction constitutive model for ultrafine quartz gouge at hypocentral conditions
Chester, F. M., & Higgs, N. G. (1992) · Journal of Geophysical Research: Solid Earth · doi:10.1029/91jb02349 · Cited by 254
Hydrolytic weakening of experimentally deformed Westerly granite and Hale albite rock
Tullis, J., & Yund, R. A. (1980) · Journal of Structural Geology · doi:10.1016/0191-8141(80)90005-x · Cited by 252
Slip patterns and earthquake populations along different classes of faults in elastic solids
Ben‐Zion, Y., & Rice, J. R. (1995) · Journal of Geophysical Research: Solid Earth · doi:10.1029/94jb03037 · Cited by 241
Effects of temperature on friction: Constitutive equations and experiments with quartz gouge
Chester, F. M. (1994) · Journal of Geophysical Research: Solid Earth · doi:10.1029/93jb03110 · Cited by 230
Kinetics of pressure solution at halite‐silica interfaces and intergranular clay films
Hickman, S. H., & Evans, B. (1995) · Journal of Geophysical Research: Solid Earth · doi:10.1029/95jb00911 · Cited by 197
Chapter 3 Frictional Strength and the Effective Pressure Law of Montmorillonite and lllite Clays
Morrow, C., Radney, B., & Byerlee, J. (1992) · International Geophysics · doi:10.1016/s0074-6142(08)62815-6 · Cited by 186
Self-citationA rheologic model for wet crust applied to strike‐slip faults
Chester, F. M. (1995) · Journal of Geophysical Research: Solid Earth · doi:10.1029/95jb00313 · Cited by 179
Ductile creep, compaction, and rate and state dependent friction within major fault zones
Sleep, N. H. (1995) · Journal of Geophysical Research: Solid Earth · doi:10.1029/94jb03340 · Cited by 168
Stress in the Lithosphere and the Strength of Active Faults
HICKMAN, S. H. (1991) · Reviews of Geophysics · doi:10.1002/rog.1991.29.s2.759 · Cited by 164
Rate laws for water‐assisted compaction and stress‐induced water‐rock interaction in sandstones
Dewers, T. A., & Hajash, A. (1995) · Journal of Geophysical Research Atmospheres · doi:10.1029/95jb00912 · Cited by 160
Retrogressive metamorphic processes in shear zones with special reference to the Lewisian complex
Beach, A. (1980) · Journal of Structural Geology · doi:10.1016/0191-8141(80)90058-9 · Cited by 140
Feldspar-influenced rock rheologies
Jänecke, S. U., & Evans, J. P. (1988) · Geology · doi:10.1130/0091-7613(1988)016<1064:firr>2.3.co;2 · Cited by 119
Sleep, N. H., & Blanpied, M. L. (1994) · Pure and Applied Geophysics · doi:10.1007/bf00874322 · Cited by 84
Self-citationCoulomb plasticity within the fault zone
Byerlee, J. D., & Savage, J. C. (1992) · Geophysical Research Letters · doi:10.1029/92gl02370 · Cited by 75
Self-citationThe mechanical behavior of faulted rock at high temperature and pressure.
Stesky, R. M. (1975) · DSpace@MIT (Massachusetts Institute of Technology) · Cited by 47
The effects of sliding velocity on the frictional and physical properties of heated fault gouge
MOORE, D. E., Summers, R., & Byerlee, J. D. (1986) · Pure and Applied Geophysics · doi:10.1007/bf00875718 · Cited by 45
Self-citation
Cited by
Strength of the lithosphere: Constraints imposed by laboratory experiments
Kohlstedt, D. L., Evans, B., & Mackwell, S. J. (1995) · Journal of Geophysical Research: Solid Earth · doi:10.1029/95jb01460 · Cited by 1,603
Bürgmann, R., & Dresen, G. (2008) · Annual Review of Earth and Planetary Sciences · doi:10.1146/annurev.earth.36.031207.124326 · Cited by 1,150
The Mechanics of Earthquakes and Faulting
Scholz, C. H. (2019) · Cambridge University Press eBooks · doi:10.1017/9781316681473 · Cited by 910
The seismogenic zone of subduction thrust faults
Hyndman, R. D., Yamano, M., & Oleskevich, D. A. (1997) · Island Arc · doi:10.1111/j.1440-1738.1997.tb00175.x · Cited by 636
Oleskevich, D. A., Hyndman, R. D., & Wang, K. (1999) · Journal of Geophysical Research: Solid Earth · doi:10.1029/1999jb900060 · Cited by 577
Metadata
- Authors
- Blanpied, M. L., Lockner, D. A., & Byerlee, J. D.
- Venue
- Journal of Geophysical Research: Solid Earth
- Publisher
- American Geophysical Union (AGU)
- Published
- 1995-07-10
- Volume
- 100
- Issue
- B7
- Pages
- 13045-13064
- ISSN
- 0148-0227 (ISSN-L)
- OpenAlex
- W2104356486
- Cited by
- 605
- References
- 41
- FWCI
- 10.12
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.