The DOI matches its Crossref record; 44 of the 44 references it cites were found in a registry or an index.
Water-based and biocompatible 2D crystal inks for all-inkjet-printed heterostructures
Open accessAbstract
Exploiting the properties of two-dimensional crystals requires a mass production method able to produce heterostructures of arbitrary complexity on any substrate. Solution processing of graphene allows simple and low-cost techniques such as inkjet printing to be used for device fabrication. However, the available printable formulations are still far from ideal as they are either based on toxic solvents, have low concentration, or require time-consuming and expensive processing. In addition, none is suitable for thin-film heterostructure fabrication due to the re-mixing of different two-dimensional crystals leading to uncontrolled interfaces and poor device performance. Here, we show a general approach to achieve inkjet-printable, water-based, two-dimensional crystal formulations, which also provide optimal film formation for multi-stack fabrication. We show examples of all-inkjet-printed heterostructures, such as large-area arrays of photosensors on plastic and paper and programmable logic memory devices. Finally, in vitro dose-escalation cytotoxicity assays confirm the biocompatibility of the inks, extending their possible use to biomedical applications.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Geim, A. K., & Novoselov, K. S. (2007) · Nature Materials · doi:10.1038/nmat1849 · Cited by 39,979
Raman Spectrum of Graphene and Graphene Layers
Ferrari, A. C., Meyer, J. C., Scardaci, V., Casiraghi, C., Lazzeri, M., Mauri, F., Piscanec, S., Jiang, D., Novoselov, K. S., Roth, S., et al. (2006) · Physical Review Letters · doi:10.1103/physrevlett.97.187401 · Cited by 15,047
Self-citationGraphene: Status and Prospects
Geim, A. K. (2009) · Science · doi:10.1126/science.1158877 · Cited by 13,942
Two-dimensional atomic crystals
Novoselov, K. S., Jiang, D., Schedin, F., Booth, T. J., Khotkevich, V. V., Morozov, S. V., & Geim, A. K. (2005) · Proceedings of the National Academy of Sciences · doi:10.1073/pnas.0502848102 · Cited by 11,788
Van der Waals heterostructures
Geim, A. K., & Grigorieva, I. V. (2013) · Nature · doi:10.1038/nature12385 · Cited by 10,875
Novoselov, K. S., Fal′ko, V. I., Colombo, L., Gellert, P. R., Schwab, M. G., & Kim, K. (2012) · Nature · doi:10.1038/nature11458 · Cited by 9,251
Roll-to-roll production of 30-inch graphene films for transparent electrodes
Bae, S., Kim, H., Lee, Y., Xu, X., Park, J.-S., Zheng, Y., Balakrishnan, J., Lei, T., Ri Kim, H., Song, Y. I., et al. (2010) · Nature Nanotechnology · doi:10.1038/nnano.2010.132 · Cited by 8,136
Two-Dimensional Nanosheets Produced by Liquid Exfoliation of Layered Materials
Coleman, J. N., Lotya, M., O’Neill, A., Bergin, S. D., King, P. J., Khan, U., Young, K., Gaucher, A., De, S., Smith, R. J., et al. (2011) · Science · doi:10.1126/science.1194975 · Cited by 7,242
Introduction to Percolation Theory
Stauffer, D., Aharony, A., & Redner, S. (1993) · Physics Today · doi:10.1063/1.2808877 · Cited by 6,666
III. An essay on the cohesion of fluids
Young, T. (1805) · Philosophical Transactions of the Royal Society of London · doi:10.1098/rstl.1805.0005 · Cited by 6,643
High-yield production of graphene by liquid-phase exfoliation of graphite
Hernandez, Y., Nicolosi, V., Lotya, M., Blighe, F. M., Sun, Z., De, S., McGovern, I. T., Holland, B., Byrne, M., Gun'Ko, Y. K., et al. (2008) · Nature Nanotechnology · doi:10.1038/nnano.2008.215 · Cited by 6,285
High-Resolution Inkjet Printing of All-Polymer Transistor Circuits
Sirringhaus, H., Kawase, T., Friend, R. H., Shimoda, T., Inbasekaran, M., Wu, W., & Woo, E. P. (2000) · Science · doi:10.1126/science.290.5499.2123 · Cited by 3,311
Field-Effect Tunneling Transistor Based on Vertical Graphene Heterostructures
Britnell, L., Gorbachev, R. V., Jalil, R., Belle, B. D., Schedin, F., Mishchenko, A., Georgiou, T., Katsnelson, M. I., Eaves, L., Morozov, S. V., et al. (2012) · Science · doi:10.1126/science.1218461 · Cited by 2,561
Liquid Phase Production of Graphene by Exfoliation of Graphite in Surfactant/Water Solutions
Lotya, M., Hernandez, Y., King, P. J., Smith, R. J., Nicolosi, V., Karlsson, L. S., Blighe, F. M., De, S., Wang, Z., McGovern, I. T., et al. (2009) · Journal of the American Chemical Society · doi:10.1021/ja807449u · Cited by 2,282
Two-dimensional flexible nanoelectronics
Akinwande, D., Petrone, N., & Hone, J. (2014) · Nature Communications · doi:10.1038/ncomms6678 · Cited by 1,910
Georgiou, T., Jalil, R., Belle, B. D., Britnell, L., Gorbachev, R. V., Morozov, S. V., Kim, Y.-J., Gholinia, A., Haigh, S. J., Makarovsky, O., et al. (2013) · Nature Nanotechnology · doi:10.1038/nnano.2012.224 · Cited by 1,751
An Introduction To Percolation Theory
Hughes, B. D. (1996) · Random Walks and Random Environments · doi:10.1093/oso/9780198537892.003.0002 · Cited by 1,731
Light-emitting diodes by band-structure engineering in van der Waals heterostructures
Withers, F., Del Pozo-Zamudio, O., Mishchenko, A., Rooney, A. P., Gholinia, A., Watanabe, K., Taniguchi, T., Haigh, S. J., Geim, A. K., Tartakovskii, A. I., et al. (2015) · Nature Materials · doi:10.1038/nmat4205 · Cited by 1,687
Self-citationMarangoni Effect Reverses Coffee-Ring Depositions
Hu, H., & Larson, R. G. (2006) · The Journal of Physical Chemistry B · doi:10.1021/jp0609232 · Cited by 1,645
Inkjet-Printed Graphene Electronics
Torrisi, F., Hasan, T., Wu, W., Sun, Z., Lombardo, A., Kulmala, T. S., Hsieh, G.-W., Jung, S., Bonaccorso, F., Paul, P. J., et al. (2012) · ACS Nano · doi:10.1021/nn2044609 · Cited by 1,195
Cheng, L., Liu, J., Gu, X., Gong, H., Shi, X., Liu, T., Wang, C., Wang, X., Liu, G., Xing, H., et al. (2014) · Advanced Materials · doi:10.1002/adma.201304497 · Cited by 1,108
High-Concentration, Surfactant-Stabilized Graphene Dispersions
Lotya, M., King, P. J., Khan, U., De, S., & Coleman, J. N. (2010) · ACS Nano · doi:10.1021/nn1005304 · Cited by 1,015
High yield exfoliation of two-dimensional chalcogenides using sodium naphthalenide
Zheng, J., Zhang, H., Dong, S., Liu, Y., Tai Nai, C., Suk Shin, H., Young Jeong, H., Liu, B., & Ping Loh, K. (2014) · Nature Communications · doi:10.1038/ncomms3995 · Cited by 787
Inkjet Printing of High Conductivity, Flexible Graphene Patterns
Secor, E. B., Prabhumirashi, P. L., Puntambekar, K., Geier, M. L., & Hersam, M. C. (2013) · The Journal of Physical Chemistry Letters · doi:10.1021/jz400644c · Cited by 693
Are There Fundamental Limitations on the Sheet Resistance and Transmittance of Thin Graphene Films?
De, S., & Coleman, J. N. (2010) · ACS Nano · doi:10.1021/nn100343f · Cited by 566
Toward Printed Integrated Circuits based on Unipolar or Ambipolar Polymer Semiconductors
Baeg, K., Caironi, M., & Noh, Y. (2013) · Advanced Materials · doi:10.1002/adma.201205361 · Cited by 522
Efficient Inkjet Printing of Graphene
Li, J., Ye, F., Vaziri, S., Muhammed, M., Lemme, M. C., & Östling, M. (2013) · Advanced Materials · doi:10.1002/adma.201300361 · Cited by 505
Teo, W. Z., Chng, E. L. K., Sofer, Z., & Pumera, M. (2014) · Chemistry – A European Journal · doi:10.1002/chem.201402680 · Cited by 422
Dispersions of Non-Covalently Functionalized Graphene with Minimal Stabilizer
Parviz, D., Das, S., Ahmed, H. S. T., Irin, F., Bhattacharia, S., & Green, M. J. (2012) · ACS Nano · doi:10.1021/nn302784m · Cited by 360
Yong, Y., Zhou, L., Gu, Z., Yan, L., Tian, G., Zheng, X., Liu, X., Zhang, X., Shi, J., Cong, W., et al. (2014) · Nanoscale · doi:10.1039/c4nr02453b · Cited by 333
High‐Concentration Aqueous Dispersions of MoS2
Yao, Y., Tolentino, L., Yang, Z., Song, X., Zhang, W., Chen, Y., & Wong, C. (2013) · Advanced Functional Materials · doi:10.1002/adfm.201201843 · Cited by 308
Inkjet deposition of liquid-exfoliated graphene and MoS2nanosheets for printed device applications
Finn, D. J., Lotya, M., Cunningham, G., Smith, R. J., McCloskey, D., Donegan, J. F., & Coleman, J. N. (2014) · J. Mater. Chem. C · doi:10.1039/c3tc31993h · Cited by 292
Ink Jet Deposition of Ceramic Suspensions: Modeling and Experiments of Droplet Formation
Reis, N., & Derby, B. (2000) · MRS Proceedings · doi:10.1557/proc-625-117 · Cited by 289
Surface tension by pendant drop
Hansen, F., & Rødsrud, G. (1991) · Journal of Colloid and Interface Science · doi:10.1016/0021-9797(91)90296-k · Cited by 284
Li, J., Naiini, M. M., Vaziri, S., Lemme, M. C., & Östling, M. (2014) · Advanced Functional Materials · doi:10.1002/adfm.201400984 · Cited by 256
MoS2 exhibits stronger toxicity with increased exfoliation
Chng, E. L. K., Sofer, Z., & Pumera, M. (2014) · Nanoscale · doi:10.1039/c4nr04907a · Cited by 189
Kostarelos, K., & Novoselov, K. S. (2014) · Nature Nanotechnology · doi:10.1038/nnano.2014.224 · Cited by 185
Self-citationHeterostructures Produced from Nanosheet-Based Inks
Withers, F., Yang, H., Britnell, L., Rooney, A. P., Lewis, E., Felten, A., Woods, C. R., Sanchez Romaguera, V., Georgiou, T., Eckmann, A., et al. (2014) · Nano Letters · doi:10.1021/nl501355j · Cited by 176
Self-citationYang, H., Hernandez, Y., Schlierf, A., Felten, A., Eckmann, A., Johal, S., Louette, P., Pireaux, J.-J., Feng, X., Mullen, K., et al. (2013) · Carbon · doi:10.1016/j.carbon.2012.11.022 · Cited by 176
Self-citationEmerging Carbon and Post-Carbon Nanomaterial Inks for Printed Electronics
Secor, E. B., & Hersam, M. C. (2015) · The Journal of Physical Chemistry Letters · doi:10.1021/jz502431r · Cited by 142
Differences in the Toxicological Potential of 2D versus Aggregated Molybdenum Disulfide in the Lung
Wang, X., Mansukhani, N. D., Guiney, L. M., Ji, Z., Chang, C. H., Wang, M., Liao, Y., Song, T., Sun, B., Li, R., et al. (2015) · Small · doi:10.1002/smll.201500906 · Cited by 128
Shah, P., Narayanan, T. N., Li, C.-Z., et al. (2015) · Nanotechnology · doi:10.1088/0957-4484/26/31/315102 · Cited by 116
Cytotoxic Assessment of Carbon Nanotube Interaction with Cell Cultures
Ali‐Boucetta, H., Al‐Jamal, K. T., & Kostarelos, K. (2011) · Methods in molecular biology · doi:10.1007/978-1-61779-052-2_19 · Cited by 64
Self-citationThe dietary effects of xanthan gum in man
Eastwood, M. A., Brydon, W. G., & Anderson, D. M. W. (1987) · Food Additives & Contaminants · doi:10.1080/02652038709373610 · Cited by 42
Cited by
Emerging Electrochromic Materials and Devices for Future Displays
Gu, C., Jia, A.-B., Zhang, Y.-M., & Zhang, S. X.-A. (2022) · Chemical Reviews · doi:10.1021/acs.chemrev.1c01055 · Cited by 833
Electrically-Transduced Chemical Sensors Based on Two-Dimensional Nanomaterials
Meng, Z., Stolz, R. M., Mendecki, L., & Mirica, K. A. (2019) · Chemical Reviews · doi:10.1021/acs.chemrev.8b00311 · Cited by 773
Recent Progress and Future Prospects of 2D‐Based Photodetectors
Huo, N., & Konstantatos, G. (2018) · Advanced Materials · doi:10.1002/adma.201801164 · Cited by 730
Pham, P. V., Bodepudi, S. C., Shehzad, K., Liu, Y., Xu, Y., Yu, B., & Duan, X. (2022) · Chemical Reviews · doi:10.1021/acs.chemrev.1c00735 · Cited by 708
Preparation of 2D material dispersions and their applications
Cai, X., Luo, Y., Liu, B., & Cheng, H.-M. (2018) · Chemical Society Reviews · doi:10.1039/c8cs00254a · Cited by 665
Metadata
- Authors
- McManus, D., Vranic, S., Withers, F., Sanchez-Romaguera, V., Macucci, M., Yang, H., Sorrentino, R., Parvez, K., Son, S.-K., Iannaccone, G., Kostarelos, K., Fiori, G., & Casiraghi, C.
- Venue
- Nature Nanotechnology
- Published
- 2017-01-30
- Volume
- 12
- Issue
- 4
- Pages
- 343-350
- ISSN
- 1748-3387 (ISSN-L)
- 1748-3395
- OpenAlex
- W2582156391
- Cited by
- 577
- References
- 44
- FWCI
- 26.52
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.