Student or educator? Sign up with your school email and get 6 months of Pro free.
CoChat

The DOI matches its Crossref record; 42 of the 42 references it cites were found in a registry or an index.

Soft, tough, and fast polyacrylate dielectric elastomer for non-magnetic motor

Open access

Published version of a preprint

Abstract

Dielectric elastomer actuators (DEAs) with large electrically-actuated strain can build light-weight and flexible non-magnetic motors. However, dielectric elastomers commonly used in the field of soft actuation suffer from high stiffness, low strength, and high driving field, severely limiting the DEA’s actuating performance. Here we design a new polyacrylate dielectric elastomer with optimized crosslinking network by rationally employing the difunctional macromolecular crosslinking agent. The proposed elastomer simultaneously possesses desirable modulus (~0.073 MPa), high toughness (elongation ~2400%), low mechanical loss (tan δ m = 0.21@1 Hz, 20 °C), and satisfactory dielectric properties ( $${\varepsilon }_{{{{{{\rm{r}}}}}}}$$ ε r = 5.75, tan δ e = 0.0019 @1 kHz), and accordingly, large actuation strain (118% @ 70 MV m −1 ), high energy density (0.24 MJ m −3 @ 70 MV m −1 ), and rapid response (bandwidth above 100 Hz). Compared with VHB TM 4910, the non-magnetic motor made of our elastomer presents 15 times higher rotation speed. These findings offer a strategy to fabricate high-performance dielectric elastomers for soft actuators.

Overview

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.1038/s41467-021-24851-w

Cites

42 of 42 references verified0 citation errors · 0 not checkable

Statistics

Figures

Fig. 1 Performance of uniform hybrid polymer network. a The precursor (ai, aiii, av) consists of n-butyl acrylate (nBA) as monomers and small-molecules (ai) or oligomers with two vinyl groups (–CH=CH2) (aiii and av) as crosslinkers. When exposed to ultraviolet light (UV-light), the precursoris cured to a flexible network (aii, named BA-S; aiv, named BA-M or BA-L; avi, named BAC2). Distribution of molecular weight for those oligomers have been tested by gel permeation chromatography (GPC) and shown in Supplementary Table 1. b Comparison of BAC2 before (left) and after (right) uniaxial stretched. c The stress–strain curves of commercial VHBTM4910 and BA-S, BA-M, BA-L, BAC2 at a stretch rate of 200 mm min−1. d Comparison of ultimate strength to modulus among VHBTM 4910, BA-S, BA-M, BA-L, BAC2, dielectric gel37, multiblock copolymers33, azo-grafted silicone28, nitroaniline modified silicone18, polyurethane19, alkyl thiols grafted silicone16 and commercial Elastosil@Film16. e, Toughness plotted against Young’s modulus for VHBTM 4910, BA-S, BA-M, BA-L, BAC2, dielectric gel37, silicones with ionic liquids17, acrylic copolymer25, nitroaniline modified silicone18, nitrile modified silicone39, alkyl thiols grafted silicone16, 3D printable silicone40, and commercial Elastosil@Film16 (Supplementary Discussion).
Fig. 1 Performance of uniform hybrid polymer network. a The precursor (ai, aiii, av) consists of n-butyl acrylate (nBA) as monomers and small-molecules (ai) or oligomers with two vinyl groups (–CH=CH2) (aiii and av) as crosslinkers. When exposed to ultraviolet light (UV-light), the precursoris cured to a flexible network (aii, named BA-S; aiv, named BA-M or BA-L; avi, named BAC2). Distribution of molecular weight for those oligomers have been tested by gel permeation chromatography (GPC) and shown in Supplementary Table 1. b Comparison of BAC2 before (left) and after (right) uniaxial stretched. c The stress–strain curves of commercial VHBTM4910 and BA-S, BA-M, BA-L, BAC2 at a stretch rate of 200 mm min−1. d Comparison of ultimate strength to modulus among VHBTM 4910, BA-S, BA-M, BA-L, BAC2, dielectric gel37, multiblock copolymers33, azo-grafted silicone28, nitroaniline modified silicone18, polyurethane19, alkyl thiols grafted silicone16 and commercial Elastosil@Film16. e, Toughness plotted against Young’s modulus for VHBTM 4910, BA-S, BA-M, BA-L, BAC2, dielectric gel37, silicones with ionic liquids17, acrylic copolymer25, nitroaniline modified silicone18, nitrile modified silicone39, alkyl thiols grafted silicone16, 3D printable silicone40, and commercial Elastosil@Film16 (Supplementary Discussion).CC BY · PubMed Central
Fig. 2 Influence of chemically uncrosslinked chains on dielectric and mechanical properties. a Schematic comparison of the polarization process of acrylic elastomer without uncrosslinked chains (ai, aii) and BAC2 sample with a considerable amount of uncrosslinked chains (aiii, aiv). b Gel fraction and swelling ratio of VHBTM4910 and synthesized elastomers. The insets show the optical images of BAC2 sample before and after swollen. c Elemental analysis comparison between CN9021NS and free chains of BAC2 after swollen. At least three samples were tested for the calculation of average value and standard deviation. d Molecular weight distribution of CN9021NS and free chains of BAC2 after swollen. e Frequency dependence of dielectric constant and dissipation factor (Tan δe) of VHBTM4910 and BAC2 before and after swollen in the range of 102–106 Hz. f, g Storage modulus (f) and mechanical loss (Tan δm) (g) as a function of temperature of VHBTM4910 and BAC2 before and after swollen. h The cyclic stress–strain curves of VHBTM4910 and BAC2 at a stretch rate of 100 mm min−1. The area encircled by the curve indicates the dissipated mechanical energy.
Fig. 2 Influence of chemically uncrosslinked chains on dielectric and mechanical properties. a Schematic comparison of the polarization process of acrylic elastomer without uncrosslinked chains (ai, aii) and BAC2 sample with a considerable amount of uncrosslinked chains (aiii, aiv). b Gel fraction and swelling ratio of VHBTM4910 and synthesized elastomers. The insets show the optical images of BAC2 sample before and after swollen. c Elemental analysis comparison between CN9021NS and free chains of BAC2 after swollen. At least three samples were tested for the calculation of average value and standard deviation. d Molecular weight distribution of CN9021NS and free chains of BAC2 after swollen. e Frequency dependence of dielectric constant and dissipation factor (Tan δe) of VHBTM4910 and BAC2 before and after swollen in the range of 102–106 Hz. f, g Storage modulus (f) and mechanical loss (Tan δm) (g) as a function of temperature of VHBTM4910 and BAC2 before and after swollen. h The cyclic stress–strain curves of VHBTM4910 and BAC2 at a stretch rate of 100 mm min−1. The area encircled by the curve indicates the dissipated mechanical energy.CC BY · PubMed Central
Fig. 3 Actuation performance. a Comparison of dielectric constant (εr) measured at 1 kHz, Young’s modulus (Y), and actuation sensitivity (β) between VHBTM4910 and BAC2 sample. b Dependence of actuation area strain on the nominal electric field for the films of VHBTM4910 and BAC2 elastomers without pre-strain. The nominal electric field is defined as voltage on films divided by initial thickness before electrically actuated. The inset shows the schematic diagrams illustrating the electro-actuation deformation process from the view of top and side directions. c Dependence of actuation area strain on the nominal electric field for the films of VHBTM 4910 and BAC2 elastomers with 400% equiaxial pre-strain. The inset displays the optical images of VHBTM 4910 and BAC2 films before and after actuated. d Time-dependent behavior of the actuated area strain of VHBTM 4910 and BAC2 films with 400% equiaxial pre-strain at 40 MV m−1. Normalized strain denotes the time-varying strain divided by strain at 600 s. e Frequency response of samples to large drive signals (5 kV) in the range of 1–100 Hz. The data were normalized to 1 at 1 Hz. f Cyclic actuation test of 50,000 cycles was performed on BAC2 film at electric field of 5 kV and excitation frequency of 5 Hz. The inset demonstrated z-axis displacement response in the last five cycles.
Fig. 3 Actuation performance. a Comparison of dielectric constant (εr) measured at 1 kHz, Young’s modulus (Y), and actuation sensitivity (β) between VHBTM4910 and BAC2 sample. b Dependence of actuation area strain on the nominal electric field for the films of VHBTM4910 and BAC2 elastomers without pre-strain. The nominal electric field is defined as voltage on films divided by initial thickness before electrically actuated. The inset shows the schematic diagrams illustrating the electro-actuation deformation process from the view of top and side directions. c Dependence of actuation area strain on the nominal electric field for the films of VHBTM 4910 and BAC2 elastomers with 400% equiaxial pre-strain. The inset displays the optical images of VHBTM 4910 and BAC2 films before and after actuated. d Time-dependent behavior of the actuated area strain of VHBTM 4910 and BAC2 films with 400% equiaxial pre-strain at 40 MV m−1. Normalized strain denotes the time-varying strain divided by strain at 600 s. e Frequency response of samples to large drive signals (5 kV) in the range of 1–100 Hz. The data were normalized to 1 at 1 Hz. f Cyclic actuation test of 50,000 cycles was performed on BAC2 film at electric field of 5 kV and excitation frequency of 5 Hz. The inset demonstrated z-axis displacement response in the last five cycles.CC BY · PubMed Central
Fig. 4 Mechanical output performance of soft non-magnetic motors made of dielectric elastomer films. a Snapshots from the Supplementary Video 1 of a spinning non-magnetic motor displaying a complete rotation cycle, where t and T denote time and rotation period, respectively. b Dependence of the rotation rate on electric field and driving frequency for the motors made of VHBTM 4910 and BAC2 films. The inset is a magnification of the data indicated by the arrow, which represents the electric field and frequency-dependent behavior of the rotation rate for VHBTM4910 based motor. c Dependence of the rotation rate on the driving frequency for the VHBTM 4910 and BAC2 based motors as well as BAC2 based motor with transmission gears at 48 MV m−1. d Comparison of the output torque and power of VHBTM 4910 and BAC2 based motors.
Fig. 4 Mechanical output performance of soft non-magnetic motors made of dielectric elastomer films. a Snapshots from the Supplementary Video 1 of a spinning non-magnetic motor displaying a complete rotation cycle, where t and T denote time and rotation period, respectively. b Dependence of the rotation rate on electric field and driving frequency for the motors made of VHBTM 4910 and BAC2 films. The inset is a magnification of the data indicated by the arrow, which represents the electric field and frequency-dependent behavior of the rotation rate for VHBTM4910 based motor. c Dependence of the rotation rate on the driving frequency for the VHBTM 4910 and BAC2 based motors as well as BAC2 based motor with transmission gears at 48 MV m−1. d Comparison of the output torque and power of VHBTM 4910 and BAC2 based motors.CC BY · PubMed Central

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Claims other papers make about this one

Each is checked against this paper’s own text: does it say what the citing paper says it does?

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cites

Show all 42 references

Cited by

See all 224

Metadata

Authors
Yin, L.-J., Zhao, Y., Zhu, J., Yang, M., Zhao, H., Pei, J.-Y., Zhong, S.-L., & Dang, Z.-M.
Affiliations
  • Tsinghua University (CN)
  • Zhengzhou University (CN)
  • North China Electric Power University (CN)
Corresponding author
  • Zhao, Huichan
  • Dang, Zhi-Min
Venue
Nature Communications
Published
2021-07-26
Volume
12
Issue
1
Pages
4517-4517
ISSN
2041-1723 (ISSN-L)
OpenAlex
W3183607983
Cited by
224
References
42
Citations by year
2026: 39 · 2025: 63 · 2024: 48 · 2023: 43 · 2022: 29 · 2021: 2
FWCI
9.26
Type
journal article
Language
en
Open access
Licence
Locations
  • Nature Communications (publishedVersion, cc-by)
  • Research Square (acceptedVersion, cc-by)
  • PubMed Central (publishedVersion, cc-by)
  • PubMed (publishedVersion)
  • RePEc: Research Papers in Economics (submittedVersion)
  • DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
Funders
National Natural Science Foundation of China (51937007)
Topics
  • Physical Sciences › Materials Science › Electronic, Optical and Magnetic Materials › Dielectric materials and actuators
  • Physical Sciences › Engineering › Mechanical Engineering › Advanced Materials and Mechanics
  • Physical Sciences › Materials Science › Materials Chemistry › Ferroelectric and Piezoelectric Materials
Keywords
dielectric elastomers, soft actuators, crosslinked networks, mechanical toughness, dielectric properties, actuation strain, energy density, response bandwidth, soft robotics

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Soft, tough, and fast polyacrylate dielectric elastomer for non-magnetic motor. https://app.cochat.ai/papers/10.1038/s41467-021-24851-w
The paper
Yin, L.-J., Zhao, Y., Zhu, J., Yang, M., Zhao, H., Pei, J.-Y., Zhong, S.-L., & Dang, Z.-M. (2021). Soft, tough, and fast polyacrylate dielectric elastomer for non-magnetic motor. Nature Communications. https://doi.org/10.1038/s41467-021-24851-w

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.