The DOI matches its Crossref record; 30 of the 30 references it cites were found in a registry or an index; 2 of the 11 sources its claims cite were checked for support.
Closed-loop recycling of polyethylene-like materials
Open accessAbstract
Plastics are key components of almost any technology today. Although their production consumes substantial feedstock resources, plastics are largely disposed of after their service life. In terms of a circular economy 1-8, reuse of post-consumer sorted polymers ('mechanical recycling') is hampered by deterioration of materials performance 9,10. Chemical recycling 1,11 via depolymerization to monomer offers an alternative that retains high-performance properties. The linear hydrocarbon chains of polyethylene 12 enable crystalline packing and provide excellent materials properties 13. Their inert nature hinders chemical recycling, however, necessitating temperatures above 600 degrees Celsius and recovering ethylene with a yield of less than 10 per cent 3,11,14. Here we show that renewable polycarbonates and polyesters with a low density of in-chain functional groups as break points in a polyethylene chain can be recycled chemically by solvolysis with a recovery rate of more than 96 per cent. At the same time, the break points do not disturb the crystalline polyethylene structure, and the desirable materials properties (like those of high-density polyethylene) are fully retained upon recycling. Processing can be performed by common injection moulding and the materials are well-suited for additive manufacturing, such as 3D printing. Selective removal from model polymer waste streams is possible. In our approach, the initial polymers result from polycondensation of long-chain building blocks, derived by state-of-the-art catalytic schemes from common plant oil feedstocks, or microalgae oils 15. This allows closed-loop recycling of polyethylene-like materials.
Overview
CoChat Summary
TL;DR
The paper demonstrates closed-loop chemical recycling of polyethylene-like polycarbonates and polyesters that contain sparse in-chain break points, achieving >96% polymer-to-polymer recovery while retaining HDPE-like crystalline and mechanical properties. The materials are made from bio-based long-chain monomers, can be injection moulded and 3D-printed, and can be selectively depolymerised from mixed polyolefin/PET waste streams.
Key findings
- PC-18 and PE-18,18 were prepared from biorefinery-derived 1,18-octadecanedioic acid. PC-18 reached Mw up to ~300,000 g mol⁻¹ (Mn ~90,000 g mol⁻¹); PE-18,18 typically reached Mw ~80,000 g mol⁻¹ (Mn ~50,000 g mol⁻¹). WAXS showed HDPE-like crystallinity of ~80%, and stress-strain properties compared to commercial HDPE.
- Chemical recycling of 20.0 g melt-processed PC-18 in 250 mL basic EtOH (10 wt% KOH, 120 °C, 24 h) gave 17.91 g 1,18-octadecanediol (98% yield, GC >99%). Repolymerisation yielded 19.25 g PC-18 (Mw ~240,000 g mol⁻¹, Mn ~70,000 g mol⁻¹), corresponding to a 96% polymer-to-polymer recycling rate.
- PE-18,18 methanolysis proceeded completely within 12 h at 150 °C without catalyst (2 h with catalyst); 25.0 g gave 27.6 g of a repolymerisable 1:1 diester/diol mixture (99 mol%). PC-18 was selectively depolymerised from mixtures with PP, HDPE, and PET, leaving those polymers intact and recovering neat diol in 98% yield (GC >99%).
- 3D-printed PC-18 showed ductility up to εb = 350% and Young’s modulus ~640 MPa; printed PE-18,18 showed Young’s modulus ~910 MPa and εb ~470%. A PC-48 cup (Tm = 113 °C) maintained shape upon repeated filling with boiling water.
Methods
- Synthesis: long-chain polycarbonates and polyesters were made by polycondensation of bio-based C18 diol/diester building blocks. PC-18 used diethyl carbonate with LiH; PE-18,18 used titanium(IV) n-butoxide; PC-48 was made from erucic acid-derived 1,48-tetraoctacontane diol.
- Processing and characterisation: injection moulding and fused filament fabrication were used; tensile tests followed ISO 527-2 type 5A; WAXS determined crystallinity; GPC, DSC, GC, NMR, IR, and SEM were used for polymer and monomer analysis.
- Recycling: solvolysis in EtOH or MeOH, with or without KOH, was tested at small and larger scale (20.0 g PC-18; 25.0 g PE-18,18), including separation from PP, HDPE, and PET and repolymerisation of recovered monomers.
Limitations
- Stated in the paper: long-chain monomers are not available at a similar price and scale as ethylene, the cheapest building block of the chemical industry. The softening points of PC-18 and PE-18,18 are too low for boiling-water applications, although PC-48 is presented as a perspective toward this target.
- Stated in the paper: depolymerisation of PE-18,18 yields a mixture of two non-volatile long-chain monomers, diester and diol, which cannot be separated easily, though the mixture can be directly repolymerised.
- Evident from the text: recycling is demonstrated at laboratory scale (20–25 g), and no life-cycle, economic, or industrial-scale assessment is reported. Extended Data Fig. 5 notes that KOH catalysis of polyester depolymerisation caused partial saponification of the 1,18-dimethyl octadecanedioate monomer.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
2 Valid · 5 Not valid · 6 Not checked · 73 Own results and interpretations
The sources with a verdict support this claim; the rest weren’t checked yet, have no full text we could read, or their verdicts aren’t rated yet.
In the paper
“desirable re-utilisation of post-consumer sorted polymers ('mechanical recycling') is hampered by deterioration of materials performance.”
What the sources say
- Supportedcites [1] Vollmer, I. et al. Beyond mechanical recycling: giving new life to plastic waste. Angew. Chem. Int. Ed. 59, 15402–15423 (2020). source
The Introduction states that mechanical recycling is typically accompanied by degraded plastic properties. The Concluding Remarks and Outlook likewise say that it leads to lower-quality materials, supporting the claim about deteriorating material performance. (LLM, conf=0.94)
- Not checked — no full text of the sourcecites [11] Lopez, G., Artetxe, M., Amutio, M., Bilbao, J. & Olazar, M. Thermochemical routes for the valorization of waste polyolefinic plastics to produce fuels and chemicals. A review. Renew. Sustain. Energy Rev. 73, 346–368 (2017). source
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
The sources with a verdict support this claim; the rest weren’t checked yet, have no full text we could read, or their verdicts aren’t rated yet.
In the paper
“Samples of polyester-18,18 (PE-18,18) and polycarbonate-18 (PC-18) had been prepared previously based on other feedstocks, 19,20 but the key challenge of achieving polyethylene-like mechanical properties had not been addressed.”
What the sources say
- Supportedcites [19] Ortmann, P., Heckler, I. & Mecking, S. Physical properties and hydrolytic degradability of polyethylene-like polyacetals and polycarbonates. Green Chem. 16, 1816–1827 (2014). source
The Conclusions (page not available) explicitly state that the authors did not elaborate mechanical behavior, even though they studied PC-18. This supports the claim that achieving polyethylene-like mechanical properties was not addressed in the cited preparation; the sentence cites other work for the earlier polyester preparation. (LLM, conf=0.88)
- Not checked — no full text of the sourcecites [20] Mutlu, H., Hofsäß, R., Montenegro, R. E. & Meier, M. A. R. Self-metathesis of fatty acid methyl esters: full conversion by choosing the appropriate plant oil. RSC Adv. 3, 4927–4934 (2013). source
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“A thin-walled (0.4 mm) cup 3D-printed from coloured PC-48 maintained its dimensions and shape upon repeated filling with boiling water (Fig. 3b).”
plainSingle case- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“In case of PC-18, depolymerisation in basic EtOH solution yields the long-chain 1,18-octadecane diol.”
plainstates a causeSingle case- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Note that in the solid-state, surface tension and wetting angles of these polymers do not differ significantly from polyethylene ( cf. Supplementary Information)”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
57 more claims
Create a free account to see all 86 claims and every source verdict.
- Probably not a substantial claim. 6
- It may state two separate claims as one. 17
- The quote only partly states this claim. 1
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The cited source doesn’t support the claim as written.
In the citing paper
“However, this approach produces a limited scope of materials and yields polymers possessing high ester content and lower thermal and materials properties relative to PE.”
From Chemically recyclable polyolefin-like multiblock polymers (2023) · cites this paper as [19]
Checked by a reasoning model — may be wrong.
Experimental — accuracy not yet measuredThe cited source says what the claim attributes to it.
In the citing paper
“The step-growth condensation polymerization of diester functionalized alkanes with diols results in PE-like materials possessing ester functionality that enables depolymerization back to the building blocks for repolymerization”
From Chemically recyclable polyolefin-like multiblock polymers (2023) · cites this paper as [19]
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Processing and fused filament fabrication 10 · p. 6
“From 1,48-tetraoctacontane diol, generated by catalytic chaindoubling of erucic acid,”
§ Polymerisation experiments · p. 20
“1,48octadecane diol (1.0 equiv.), synthesised from erucic acid by a reported catalytic procedure,”
Citations
Cites
ATTRACTIVE FORCES AT INTERFACES
Fowkes, F. M. (1964) · Industrial & Engineering Chemistry · doi:10.1021/ie50660a008 · Cited by 3,302
Mechanical and chemical recycling of solid plastic waste
Ragaert, K., Delva, L., & Van Geem, K. (2017) · Waste Management · doi:10.1016/j.wasman.2017.07.044 · Cited by 3,276
Sustainable polymers from renewable resources
Zhu, Y., Romain, C., & Williams, C. K. (2016) · Nature · doi:10.1038/nature21001 · Cited by 2,762
Chemical recycling of waste plastics for new materials production
Rahimi, A., & García, J. M. (2017) · Nature Reviews Chemistry · doi:10.1038/s41570-017-0046 · Cited by 2,121
What is a green solvent? A comprehensive framework for the environmental assessment of solvents
Capello, C., Fischer, U., & Hungerbühler, K. (2007) · Green Chemistry · doi:10.1039/b617536h · Cited by 1,917
Beyond Mechanical Recycling: Giving New Life to Plastic Waste
Vollmer, I., Jenks, M. J. F., Roelands, M. C. P., White, R. J., van Harmelen, T., de Wild, P., van der Laan, G. P., Meirer, F., Keurentjes, J. T. F., & Weckhuysen, B. M. (2020) · Angewandte Chemie International Edition · doi:10.1002/anie.201915651 · Cited by 1,905
Chemical recycling to monomer for an ideal, circular polymer economy
Coates, G. W., & Getzler, Y. D. Y. L. (2020) · Nature Reviews Materials · doi:10.1038/s41578-020-0190-4 · Cited by 1,644
SURFACE ANALYSIS - "Interdisciplinary Aspects of Surface Phenomena"
Bonis, L. J. (1964) · Industrial & Engineering Chemistry · doi:10.1021/ie50655a007 · Cited by 1,239
Oils and Fats as Renewable Raw Materials in Chemistry
Biermann, U., Bornscheuer, U., Meier, M. A. R., Metzger, J. O., & Schäfer, H. J. (2011) · Angewandte Chemie International Edition · doi:10.1002/anie.201002767 · Cited by 1,003
Catalysis as an Enabling Science for Sustainable Polymers
Zhang, X., Fevre, M., Jones, G. O., & Waymouth, R. M. (2018) · Chemical Reviews · doi:10.1021/acs.chemrev.7b00329 · Cited by 936
Research works printed but not linked: 2
- Strobl, G. R. The Physics of Polymers (Springer, 2007).
- Technology—manufacturing. Elevance Renewable Sciences https://elevance.com/technology/?highlight=press%20release (2013).
Cited by
Bioplastics for a circular economy
Rosenboom, J.-G., Langer, R., & Traverso, G. (2022) · Nature Reviews Materials · doi:10.1038/s41578-021-00407-8 · Cited by 2,116
Electrocatalytic upcycling of polyethylene terephthalate to commodity chemicals and H2 fuel
Zhou, H., Ren, Y., Li, Z., Xu, M., Wang, Y., Ge, R., Kong, X., Zheng, L., & Duan, H. (2021) · Nature Communications · doi:10.1038/s41467-021-25048-x · Cited by 769
Toward polymer upcycling—adding value and tackling circularity
Korley, L. T. J., Epps, T. H., Helms, B. A., & Ryan, A. J. (2021) · Science · doi:10.1126/science.abg4503 · Cited by 719
Managing Plastic Waste─Sorting, Recycling, Disposal, and Product Redesign
Lange, J.-P. (2021) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.1c05013 · Cited by 637
Current trends of unsustainable plastic production and micro(nano)plastic pollution
Walker, T. R., & Fequet, L. (2023) · TrAC Trends in Analytical Chemistry · doi:10.1016/j.trac.2023.116984 · Cited by 557
Metadata
- Authors
- Häußler, M., Eck, M., Rothauer, D., & Mecking, S.
- Affiliations
- University of Konstanz (DE)
- Corresponding author
- Mecking, Stefan
- Venue
- Nature
- Published
- 2021-02-17
- Volume
- 590
- Issue
- 7846
- Pages
- 423-427
- ISSN
- 0028-0836 (ISSN-L)
- 1476-4687
- OpenAlex
- W3133455371
- Cited by
- 753
- References
- 30
- Citations by year
- 2026: 101 · 2025: 176 · 2024: 150 · 2023: 140 · 2022: 133 · 2021: 53
- FWCI
- 42.19
- Type
- journal article
- Language
- en
- Open access
- green
- nbn-resolving.de
- Licence
- www.springer.com/tdm (tdm)
- www.springer.com/tdm (vor)
- Locations
- Nature (publishedVersion)
- PubMed (publishedVersion)
- KOPS (University of Konstanz) (submittedVersion)
- RePEc: Research Papers in Economics (submittedVersion)
- Funders
- H2020 European Research Council (832480)
- Topics
- Physical Sciences › Materials Science › Polymers and Plastics › Polymer crystallization and properties
- Physical Sciences › Materials Science › Biomaterials › biodegradable polymer synthesis and properties
- Physical Sciences › Materials Science › Polymers and Plastics › Polymer composites and self-healing
- Keywords
- closed-loop recycling, chemical recycling, solvolysis, depolymerization, polycarbonate, polyesters, bio-based polymers, microalgae oil, high-density polyethylene, circular economy, polymer waste, 3D printing, injection molding
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Closed-loop recycling of polyethylene-like materials. https://app.cochat.ai/papers/10.1038/s41586-020-03149-9
- The paper
- Häußler, M., Eck, M., Rothauer, D., & Mecking, S. (2021). Closed-loop recycling of polyethylene-like materials. Nature. https://doi.org/10.1038/s41586-020-03149-9
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.