The DOI matches its Crossref record; 2 of the 2 references it cites were found in a registry or an index.
Mechanical behavior of a soft hydrogel reinforced with three-dimensional printed microfibre scaffolds
Open accessAbstract
Reinforcing hydrogels with micro-fibre scaffolds obtained by a Melt-Electrospinning Writing (MEW) process has demonstrated great promise for developing tissue engineered (TE) constructs with mechanical properties compatible to native tissues. However, the mechanical performance and reinforcement mechanism of the micro-fibre reinforced hydrogels is not yet fully understood. In this study, FE models, implementing material properties measured experimentally, were used to explore the reinforcement mechanism of fibre-hydrogel composites. First, a continuum FE model based on idealized scaffold geometry was used to capture reinforcement effects related to the suppression of lateral gel expansion by the scaffold, while a second micro-FE model based on micro-CT images of the real construct geometry during compaction captured the effects of load transfer through the scaffold interconnections. Results demonstrate that the reinforcement mechanism at higher scaffold volume fractions was dominated by the load carrying-ability of the fibre scaffold interconnections, which was much higher than expected based on testing scaffolds alone because the hydrogel provides resistance against buckling of the scaffold. We propose that the theoretical understanding presented in this work will assist the design of more effective composite constructs with potential applications in a wide range of TE conditions.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
van Rietbergen, B., Weinans, H., Huiskes, R., & Odgaard, A. (1995) · Journal of Biomechanics · doi:10.1016/0021-9290(95)80008-5 · Cited by 865
Direct writing by way of melt electrospinning
Brown, T. D., Dalton, P. D., & Hutmacher, D. W. (2011) · Advanced Materials · doi:10.1002/adma.201103482 · Cited by 800
Self-citation
Cited by
An Introduction to 3D Bioprinting: Possibilities, Challenges and Future Aspects
Kačarević, Ž. P., Rider, P. M., Alkildani, S., Retnasingh, S., Smeets, R., Jung, O., Ivanišević, Z., & Barbeck, M. (2018) · Materials · doi:10.3390/ma11112199 · Cited by 479
3D Bioprinting: from Benches to Translational Applications
Heinrich, M. A., Liu, W., Jimenez, A., Yang, J., Akpek, A., Liu, X., Pi, Q., Mu, X., Hu, N., Schiffelers, R. M., et al. (2019) · Small · doi:10.1002/smll.201805510 · Cited by 437
Polymers for Melt Electrowriting
Kade, J. C., & Dalton, P. D. (2021) · Advanced Healthcare Materials · doi:10.1002/adhm.202001232 · Cited by 270
Self-citationThe Next Frontier in Melt Electrospinning: Taming the Jet
Robinson, T. M., Hutmacher, D. W., & Dalton, P. D. (2019) · Advanced Functional Materials · doi:10.1002/adfm.201904664 · Cited by 267
Self-citation
Metadata
- Authors
- Castilho, M., Hochleitner, G., Wilson, W., van Rietbergen, B., Dalton, P. D., Groll, J., Malda, J., & Ito, K.
- Venue
- Scientific Reports
- Published
- 2018-01-19
- Volume
- 8
- Issue
- 1
- Pages
- 1245-1245
- ISSN
- 2045-2322 (ISSN-L)
- OpenAlex
- W2783736633
- Cited by
- 169
- References
- 2
- FWCI
- 5.76
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Mechanical behavior of a soft hydrogel reinforced with three-dimensional printed microfibre scaffolds. https://app.cochat.ai/papers/10.1038/s41598-018-19502-y
- The paper
- Castilho, M., Hochleitner, G., Wilson, W., van Rietbergen, B., Dalton, P. D., Groll, J., Malda, J., & Ito, K. (2018). Mechanical behavior of a soft hydrogel reinforced with three-dimensional printed microfibre scaffolds. Scientific Reports. https://doi.org/10.1038/s41598-018-19502-y
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.