The DOI matches its Crossref record; 33 of the 33 references it cites were found in a registry or an index.
Turning renewable resources into value-added polymer: development of lignin-based thermoplastic
Abstract
Productive uses of lignin, the third most abundant natural polymer, have been sought for decades. One especially attractive possibility is that of developing value-added products including thermoplastics based on lignin. This possibility warrants special attention due to growth of the modern biofuel industries. However, the polydisperse molecular weight and hyper-branched structure of lignin has hindered the creation of high-performance biopolymers. Here, we report the preparation and characterization of novel lignin-based, partially carbon-neutral thermoplastics. We first altered the molecular weight of lignin, either by fractionation with methanol, or by formaldehyde crosslinking. Crosslinking of lignin increases the molecular weight, exhibiting Mn = 31 000 g mol−1, whereas that of as-received lignin is 1840 g mol−1. Tuning the molecular weight of lignin enabled successful preparation of novel lignin-derived thermoplastics, when coupled with telechelic polybutadiene soft-segments at proper feed ratios. Characteristic to thermoplastic rubbers, free-standing films of the resulting copolymers exhibit two-phase morphology and associated relaxations in the dynamic mechanical loss spectrum. To the best of our knowledge this article is the first report to demonstrate phase immiscibility, melt-processibility, and biphasic morphology of soft and hard segments in a lignin-based copolymer for all feed ratios of two macromolecular components. The use of higher molecular weight lignin enhanced the resulting shear modulus due to efficient network formation of telechelic polybutadiene bridges. The storage modulus in the rubbery plateau region increased with increasing lignin content. The successful synthesis of novel lignin-based thermoplastics will open a new pathway to biomass utilization and will help conserve petrochemicals.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
The Path Forward for Biofuels and Biomaterials
Ragauskas, A. J., Williams, C. K., Davison, B. H., Britovsek, G., Cairney, J., Eckert, C. A., Frederick, W. J., Hallett, J. P., Leak, D. J., Liotta, C. L., et al. (2006) · Science · doi:10.1126/science.1114736 · Cited by 5,741
Recent Industrial Applications of Lignin: A Sustainable Alternative to Nonrenewable Materials
Lora, J. H., & Glasser, W. G. (2002) · Journal of Polymers and the Environment · doi:10.1023/a:1021070006895 · Cited by 1,176
The Chemical Composition of Wood
PETTERSEN, R. C. (1984) · Advances in Chemistry · doi:10.1021/ba-1984-0207.ch002 · Cited by 874
Gosselink, R. J. A., de Jong, E., Guran, B., & Abächerli, A. (2004) · Industrial Crops and Products · doi:10.1016/j.indcrop.2004.04.015 · Cited by 533
A Comprehensive Approach for Quantitative Lignin Characterization by NMR Spectroscopy
Capanema, E. A., Balakshin, M. Y., & Kadla, J. F. (2004) · Journal of Agricultural and Food Chemistry · doi:10.1021/jf035282b · Cited by 504
Pan, X., Gilkes, N., Kadla, J., Pye, K., Saka, S., Gregg, D., Ehara, K., Xie, D., Lam, D., & Saddler, J. (2006) · Biotechnology and Bioengineering · doi:10.1002/bit.20905 · Cited by 455
Lignin Esters for Use in Unsaturated Thermosets: Lignin Modification and Solubility Modeling
Thielemans, W., & Wool, R. P. (2005) · Biomacromolecules · doi:10.1021/bm0500345 · Cited by 305
Capanema, E. A., Balakshin, M. Y., & Kadla, J. F. (2005) · Journal of Agricultural and Food Chemistry · doi:10.1021/jf0515330 · Cited by 277
Lignins: Major Sources, Structure and Properties
Gellerstedt, G., & Henriksson, G. (2008) · Monomers, Polymers and Composites from Renewable Resources · doi:10.1016/b978-0-08-045316-3.00009-0 · Cited by 265
Novel applications of lignin in composite materials
Thielemans, W., Can, E., Morye, S. S., & Wool, R. P. (2002) · Journal of Applied Polymer Science · doi:10.1002/app.2247 · Cited by 252
Whited, G. M., Feher, F. J., Benko, D. A., Cervin, M. A., Chotani, G. K., McAuliffe, J. C., LaDuca, R. J., Ben-Shoshan, E. A., & Sanford, K. J. (2010) · Industrial Biotechnology · doi:10.1089/ind.2010.6.152 · Cited by 218
Lignin Structural Modifications Resulting from Ethanol Organosolv Treatment of Loblolly Pine
Sannigrahi, P., Ragauskas, A. J., & Miller, S. J. (2010) · Energy & Fuels · doi:10.1021/ef900845t · Cited by 198
Engineering plastics from lignin. I. Synthesis of hydroxypropyl lignin
Wu, L. C. ‐., & Glasser, W. G. (1984) · Journal of Applied Polymer Science · doi:10.1002/app.1984.070290408 · Cited by 171
Properties of lignin–polyurethane films prepared by casting method
Ciobanu, C., Ungureanu, M. I., Ignat, M.-E., Ungureanu, D., & Popa, V. (2004) · Industrial Crops and Products · doi:10.1016/j.indcrop.2004.04.024 · Cited by 170
Biosynthesis of isoprene in Escherichia coli via methylerythritol phosphate (MEP) pathway
Zhao, Y., Yang, J., Qin, B., Li, Y., Sun, Y., Su, S., & Xian, M. (2011) · Applied Microbiology and Biotechnology · doi:10.1007/s00253-011-3199-1 · Cited by 163
Alcell® lignin solubility in ethanol–water mixtures
Ni, Y., & Hu, Q. (1995) · Journal of Applied Polymer Science · doi:10.1002/app.1995.070571203 · Cited by 161
Hotta, A., Cochran, E. W., Ruokolainen, J., Khanna, V., Fredrickson, G. H., Krämer, E. J., Shin, Y.-W., Shimizu, F., Cherian, A. E., Hustad, P. D., et al. (2006) · Proceedings of the National Academy of Sciences · doi:10.1073/pnas.0602894103 · Cited by 142
Yoshida, H., Mörck, R., Kringstad, K. P., & Hatakeyama, H. (1990) · Journal of Applied Polymer Science · doi:10.1002/app.1990.070401102 · Cited by 136
Thring, R. W., Chornet, E., & Overend, R. P. (1990) · Biomass · doi:10.1016/0144-4565(90)90038-l · Cited by 134
Reid, I. D. (1995) · Canadian Journal of Botany · doi:10.1139/b95-351 · Cited by 132
Studies on heat capacity of cellulose and lignin by differential scanning calorimetry
Hatakeyama, T., Nakamura, K., & Hatakeyama, H. (1982) · Polymer · doi:10.1016/0032-3861(82)90125-2 · Cited by 125
Polyurethanes and polyesters from lignin
Bonini, C., D’Auria, M., Emanuele, L., Ferri, R., Pucciariello, R., & Sabia, A. R. (2005) · Journal of Applied Polymer Science · doi:10.1002/app.22277 · Cited by 115
Fractionation Of Alcell® Lignin By Sequential Solvent Extraction
Thring, R. W., Vanderlaan, M. N., & Griffin, S. L. (1996) · Journal of Wood Chemistry and Technology · doi:10.1080/02773819608545815 · Cited by 107
Pyrolysis oils from CO2 precipitated Kraft lignin
Kosa, M., Ben, H., Theliander, H., & Ragauskas, A. J. (2011) · Green Chemistry · doi:10.1039/c1gc15818j · Cited by 106
Alkaline degradation of ALCELL® lignin
Thring, R. W. (1994) · Biomass and Bioenergy · doi:10.1016/0961-9534(94)00051-t · Cited by 93
Properties of phenol‐formaldehyde resins prepared from phenol‐liquefied lignin
Lee, W., Chang, K., & Tseng, I. (2011) · Journal of Applied Polymer Science · doi:10.1002/app.35539 · Cited by 93
Polyurethanes from Alcell® lignin fractions obtained by sequential solvent extraction
Vanderlaan, M. N., & Thring, R. W. (1998) · Biomass and Bioenergy · doi:10.1016/s0961-9534(97)10058-7 · Cited by 89
Lignins as Macromonomers for Polyesters and Polyurethanes
Gandini, A., Belgacem, M. N., Guo, Z., & Montanari, S. (2002) · Springer eBooks · doi:10.1007/978-1-4615-0643-0_4 · Cited by 64
Cardanol-Lignin-Based Polyurethanes
Tan, T. T. M. (1996) · Polymer International · doi:10.1002/(sici)1097-0126(199609)41:1<13::aid-pi557>3.0.co;2-8 · Cited by 48
Engineering plastics from lignin. XV. Polyurethane films from chain‐extended hydroxypropyl lignin
Kelley, S. S., Glasser, W. G., & Ward, T. C. (1988) · Journal of Applied Polymer Science · doi:10.1002/app.1988.070360403 · Cited by 39
Multiphase materials with lignin. XV. Blends of cellulose acetate butyrate with lignin esters
Ghosh, I., Jain, R. K., & Glasser, W. G. (1999) · Journal of Applied Polymer Science · Cited by 38
New approaches to wood bonding A base-activated lignin adhesive system
Young, R. A., Fujita, M., & River, B. H. (1985) · Wood Science and Technology · doi:10.1007/bf00350813 · Cited by 33
Young, R. A. (1985) · Wood Science and Technology · doi:10.1007/bf00354749 · Cited by 24
Cited by
Chemical modification of lignins: Towards biobased polymers
Laurichesse, S., & Avérous, L. (2014) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2013.11.004 · Cited by 2,058
A concise review of current lignin production, applications, products and their environmental impact
Bajwa, D. S., Pourhashem, G., Ullah, A. H., & Bajwa, S. G. (2019) · Industrial Crops and Products · doi:10.1016/j.indcrop.2019.111526 · Cited by 1,270
Towards lignin-based functional materials in a sustainable world
Kai, D., Tan, M. J., Chee, P. L., Chua, Y. K., Yap, Y. L., & Loh, X. J. (2016) · Green Chemistry · doi:10.1039/c5gc02616d · Cited by 1,267
Figueiredo, P., Lintinen, K., Hirvonen, J. T., Kostiainen, M. A., & Santos, H. A. (2018) · Progress in Materials Science · doi:10.1016/j.pmatsci.2017.12.001 · Cited by 956
A review on lignin-based polymeric, micro- and nano-structured materials
Duval, A., & Lawoko, M. (2014) · Reactive and Functional Polymers · doi:10.1016/j.reactfunctpolym.2014.09.017 · Cited by 733
Metadata
- Authors
- Saito, T., Brown, R. H., Hunt, M. A., Pickel, D. L., Pickel, J. M., Messman, J. M., Baker, F. S., Keller, M., & Naskar, A. K.
- Venue
- Green Chemistry
- Publisher
- Royal Society of Chemistry (RSC)
- Published
- 2012
- Volume
- 14
- Issue
- 12
- Pages
- 3295
- ISSN
- 1463-9262 (ISSN-L)
- 1463-9270
- OpenAlex
- W2036431603
- Cited by
- 395
- References
- 33
- FWCI
- 11.68
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.