CoChat

Lubricating properties of single metal ions at interfaces

Open access
Cafolla, Clodomiro, Voïtchovsky, Kislon · 2018 · Nanoscale

The DOI matches its Crossref record; 80 of the 80 references it cites were found in a registry or an index; 11 of the 92 sources its claims cite were checked for support.

Abstract

The behaviour of ionic solutions confined in nanoscale gaps is central to countless processes, from biomolecular function to electrochemistry, energy storage and lubrication. However, no clear link exists between the molecular-level behaviour of the liquid and macroscopic observations. The problem mainly comes from the difficulty to interrogate a small number of liquid molecules. Here, we use atomic force microscopy to investigate the viscoelastic behaviour of pure water and ionic solutions down to the single ion level. The results show a glassy-like behaviour for pure water, with single metal ions acting as lubricants by reducing the elasticity of the nano-confined solution and the magnitude of the hydrodynamic friction. At small ionic concentration (<20 mM) the results can be quantitatively explained by the ions moving via a thermally-activated process resisted by the ion's hydration water (Prandtl-Tomlinson model). The model breaks down at higher salt concentrations due to ion-ion interaction effects that can no longer be neglected. The correlations are confirmed by direct sub-nanometre imaging of the interface at equilibrium. The results provide a molecular-level basis for explaining the tribological properties of aqueous solutions and suggest that ion-ion interactions create mesoscale effects that prevent a direct link between nanoscale and macroscopic measurements.

Overview

CoChat Summary

## TL;DR

Using AFM shear-force spectroscopy and high-resolution imaging, the paper shows that single metal ions can lubricate nano-confined water between mica and an AFM tip by reducing elasticity, friction, and energy dissipation. The effect is strongest at low salt concentrations, but at higher concentrations ion–ion interactions and mesoscale ordering make the simple single-ion picture break down.

## Key findings

  • In pure water, the nano-confined liquid shows a “glassy-like” response; adding ions reduces the shear force and energy dissipation, and increases the phase toward more viscous behavior.
  • For hard confinement, the paper reports effective friction coefficients of μwater = 0.142 ± 0.002, μRb = 0.089 ± 0.001, μK = 0.074 ± 0.003, μNa = 0.077 ± 0.004, and μCa = 0.059 ± 0.002, with the magnitude decreasing exponentially with cation charge density.
  • At low ionic concentration (<20 mM), the behavior is quantitatively described by a thermally activated Prandtl–Tomlinson-type process; the paper estimates Ea ∼ 1.26 kBT and γ ∼ 10−3 ≪ 1.
  • In soft confinement, pure water shows increased effective viscosity already at about 2 nm from the mica surface, while ionic solutions show increased shear only below about 0.5 nm; the relaxation time is estimated at τ ∼ 0.01–0.1 ms.
  • Varying KCl concentration gives a non-monotonic response: friction and dissipation reach a minimum at about 75 mM KCl, after which lubrication deteriorates and the response becomes more viscous again.

## Methods

  • The study used atomic force microscopy on mica against an AFM tip, combining sub-nanometre shear-force spectroscopy with atomic-level imaging of the confined interface.
  • Solutions tested were ultrapure water, RbCl, KCl, NaCl, and CaCl2, with ionic solutions typically at 5 mM and pH 5.38; the paper also varied pH and KCl concentration.
  • For shear measurements, the authors acquired about 100 shear-force curves across typically five locations per solution and analyzed shear force, phase lag, dissipated energy, and effective viscosity using calibrated AFM parameters.

## Limitations

  • The paper states that the continuous-fluid assumption breaks down at very short tip-sample distances where only one or two water layers remain.
  • The authors note that the Prandtl–Tomlinson interpretation breaks down at higher salt concentrations because ion–ion interactions can no longer be neglected.
  • The text also makes evident that the small confinement area and poor control of tip geometry make interpretation challenging, and that the measured nanoscale behavior cannot be directly extrapolated to larger confining areas or shear amplitudes.

Model-written summary. Check it against the paper before relying on it.

Integrity signals

Registry

Crossref · 10.1039/c8nr02859a

Cites

80 of 80 references verified0 citation errors · 0 not checkable

Statistics

Nothing to recompute.

Figures

Fig. 1 High-resolution AFM images of the interface between mica and di ff erent experimental solutions. In each solution, both the topographic ( purple-orange colour scale) and phase (blue colour scale) information are shown. (a) Hydration landscape of the mica surface in pure water. The lighter (higher) areas indicate regions where water molecules form an epitaxial lattice-like arrangement, with 2 -3 nm wide domains. (b) In RbCl, the Rb + ions tend to form large correlated epitaxial domains, leading to an interface appearing almost uniform at this concentration. (c) K + ions behave in a similar fashion as Rb + (attractive correlation interactions at the interface), resulting in distinctive elongated domains (green arrow). (d) Na + ions exhibit no clear structural organization due to higher mobility and multiple solvation states. (e) Ca 2+ ions also organise into domains but with many defects due to the multiple hydration states and adsorption to interstitial sites (position 2 in f). (f) Cartoon representation of the cleaved mica surface. The scale bar is 3 nm in all images. The colour scale represents height variations of 0.5 nm in topography and 30° in phase. All the ionic solutions with added salt (5 mM) are at pH 5.38. The temperature is 25.0 ± 0.1 °C.
Fig. 1 High-resolution AFM images of the interface between mica and di ff erent experimental solutions. In each solution, both the topographic ( purple-orange colour scale) and phase (blue colour scale) information are shown. (a) Hydration landscape of the mica surface in pure water. The lighter (higher) areas indicate regions where water molecules form an epitaxial lattice-like arrangement, with 2 -3 nm wide domains. (b) In RbCl, the Rb + ions tend to form large correlated epitaxial domains, leading to an interface appearing almost uniform at this concentration. (c) K + ions behave in a similar fashion as Rb + (attractive correlation interactions at the interface), resulting in distinctive elongated domains (green arrow). (d) Na + ions exhibit no clear structural organization due to higher mobility and multiple solvation states. (e) Ca 2+ ions also organise into domains but with many defects due to the multiple hydration states and adsorption to interstitial sites (position 2 in f). (f) Cartoon representation of the cleaved mica surface. The scale bar is 3 nm in all images. The colour scale represents height variations of 0.5 nm in topography and 30° in phase. All the ionic solutions with added salt (5 mM) are at pH 5.38. The temperature is 25.0 ± 0.1 °C.CC-BY · From the PDF
Image 2
CC-BY · From the PDF
Fig. 3 Evolution of the shear force (a), phase (b) and energy dissipated per shear cycle (c) as functions of the con fi ning force for di ff erent concentrations of KCl in aqueous solutions. The evolution is non-monotonous with a minimum in F shear and E diss at 75 mM KCl, coinciding with a strongly elastic behaviour of the con fi ned liquid. This is clearly visible at low con fi ning pressures ( ∼ 0 nN). For easier comparison, the insets (a -c) show respectively F shear , φ t and E diss as functions of ionic concentration for given applied forces.
Fig. 3 Evolution of the shear force (a), phase (b) and energy dissipated per shear cycle (c) as functions of the con fi ning force for di ff erent concentrations of KCl in aqueous solutions. The evolution is non-monotonous with a minimum in F shear and E diss at 75 mM KCl, coinciding with a strongly elastic behaviour of the con fi ned liquid. This is clearly visible at low con fi ning pressures ( ∼ 0 nN). For easier comparison, the insets (a -c) show respectively F shear , φ t and E diss as functions of ionic concentration for given applied forces.CC-BY · From the PDF
Fig. 4 Shear force (a), phase (b) and e ff ective viscosity (c) as functions of the tip -sample distance. The force increases below distances of ∼ 2 nm in pure water and ∼ 0.5 nm in ionic solution. The inset in (a) shows the evolution of the energy dissipated per shear cycle. The response of nano-con fi ned water induces a greater dissipation of energy than in ionic solutions. In (b) the phase is unde fi ned at large tip -sample distance due to the shear amplitude and force being close to the noise level ( φ t > 90°, semi-transparent region). (c) The e ff ective viscosity of the interfacial liquid increases by orders of magnitude in pure water, but changes in ionic solutions are close to the noise limit (except for NaCl). The yellow and blue dotted lines indicate regions where the con fi nement is smaller than one or two water molecules, respectively. For such small nanogaps, the assumption of continuous fl uid implicit to eqn (6) breaks down. 17 In the non-contact region, the shearing area is A ∼ 10 nm 2 . The slip length of mica was taken to be zero. 29
Fig. 4 Shear force (a), phase (b) and e ff ective viscosity (c) as functions of the tip -sample distance. The force increases below distances of ∼ 2 nm in pure water and ∼ 0.5 nm in ionic solution. The inset in (a) shows the evolution of the energy dissipated per shear cycle. The response of nano-con fi ned water induces a greater dissipation of energy than in ionic solutions. In (b) the phase is unde fi ned at large tip -sample distance due to the shear amplitude and force being close to the noise level ( φ t > 90°, semi-transparent region). (c) The e ff ective viscosity of the interfacial liquid increases by orders of magnitude in pure water, but changes in ionic solutions are close to the noise limit (except for NaCl). The yellow and blue dotted lines indicate regions where the con fi nement is smaller than one or two water molecules, respectively. For such small nanogaps, the assumption of continuous fl uid implicit to eqn (6) breaks down. 17 In the non-contact region, the shearing area is A ∼ 10 nm 2 . The slip length of mica was taken to be zero. 29CC-BY · From the PDF
Fig. 5 Evolution of the shear force, energy dissipated per shear cycle and phase as functions of pH in KCl. Results are shown for hard con fi nement (a -b) and soft con fi nement (c -d). The insets in (a) and (c) show the energy dissipated per shear cycle. At tip -sample distance < 0.5 nm, the shear force and the energy dissipation increase with decreasing pH. These results are consistent with hydronium ions competing with metal cations for binding sites on mica, thereby limiting the metal cations ' ability to lubricate the system. The experiments are performed at 25 ± 0.1 °C. In (b) and (d) the phase is unde fi ned at large tip -sample distance and small con fi ning forces due to the shear amplitude and hence force being close to the noise level ( φ t > 90°, semi-transparent region).
Fig. 5 Evolution of the shear force, energy dissipated per shear cycle and phase as functions of pH in KCl. Results are shown for hard con fi nement (a -b) and soft con fi nement (c -d). The insets in (a) and (c) show the energy dissipated per shear cycle. At tip -sample distance < 0.5 nm, the shear force and the energy dissipation increase with decreasing pH. These results are consistent with hydronium ions competing with metal cations for binding sites on mica, thereby limiting the metal cations ' ability to lubricate the system. The experiments are performed at 25 ± 0.1 °C. In (b) and (d) the phase is unde fi ned at large tip -sample distance and small con fi ning forces due to the shear amplitude and hence force being close to the noise level ( φ t > 90°, semi-transparent region).CC-BY · From the PDF

Verification

Claims the paper makes

8 Valid · 3 Not valid · 38 Not checked · 96 Own results and interpretations

57 more claims

Create a free account to see all 145 claims and to verify the 11 references still open.

See all claims — free account
  • It may state two separate claims as one. 65
  • Probably not a substantial claim. 27
  • Borderline: one of the tests for a substantial claim is unclear. 1
  • The quote only partly states this claim. 1

Create a free account to see these claims.

Citations

Cites

Show all 80 references

Research works printed but not linked: 6

  1. Stanley, 2010, J. Phys.: Condens. Matter, 22, 284101
  2. Zangi, 2004, J. Phys.: Condens. Matter, 16, S5371
  3. Cerveny, 2007, Eur. Phys. J., 141, 49
  4. Miller, 2016, J. Visualized Exp., 118, e54924
  5. Klein, 2004, J. Phys.: Condens. Matter, 16, S5437
  6. Guerra, 2010, Phys. Rev. E, 78, 03611

Cited by

Metadata

Authors
Cafolla, C., & Voïtchovsky, K.
Affiliations
  • Durham University (GB)
  • Physics Department
Venue
Nanoscale
Published
2018
Volume
10
Issue
25
Pages
11831-11840
ISSN
  • 2040-3364 (ISSN-L)
  • 2040-3372
OpenAlex
W2809065824
Cited by
31
References
80
Citations by year
2026: 4 · 2025: 1 · 2024: 7 · 2023: 6 · 2022: 2 · 2021: 3 · 2020: 5 · 2019: 2 · 2018: 1
FWCI
1.27
Type
journal article
Language
en
Open access
Locations
  • Nanoscale (publishedVersion, cc-by)
  • PubMed (publishedVersion)
  • Durham Research Online (Durham University) (publishedVersion, other-oa)
  • Durham Research Online (Durham University) (acceptedVersion, other-oa)
  • Durham Research Online (Durham University) (submittedVersion, cc-by)
Funders
  • Engineering and Physical Sciences Research Council (iCASE studentship EP/P510476/1)
  • Durham University
Topics
  • Physical Sciences › Physics and Astronomy › Atomic and Molecular Physics, and Optics › Force Microscopy Techniques and Applications
  • Physical Sciences › Engineering › Mechanical Engineering › Lubricants and Their Additives
  • Physical Sciences › Engineering › Biomedical Engineering › Nanopore and Nanochannel Transport Studies
Keywords
lubrication, viscoelasticity, hydrodynamic friction, Prandtl-Tomlinson model, ion hydration, ion-ion interactions, atomic force microscopy, salt effects

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

The claim verdicts this report counts are experimental: their accuracy is not yet measured.

A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).

A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).

Cited sources are checked with a language model’s help (gpt-6-sol and qwen3.8-omni-flash).

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.