The DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index.
Contact and Rubbing of Flat Surfaces
Abstract
The interpretation of certain phenomena occuring at nominally flat surfaces in stationary or sliding contact is dependent on the assumed distribution of the real area of contact between the surfaces. Since there is little direct evidence on which to base an estimate of this distribution, the approach used is to set up a simple model and compare the deduced theory (e.g., the deduced dependence of the experimental observables on the load) with the experimental evidence. The main conclusions are as follows. (a) The electrical contact resistance depends on the model used to represent the surfaces; the most realistic model is one in which increasing the load increases both the number and size of the contact areas. (b) In general, mechanical wear should also depend on the model. However, in wear experiments showing the simplest behavior, the wear rate is proportional to the load, and these results can be explained by assuming removal of lumps at contact areas formed by plastic deformation; moreover, this particular deduction is independent of the assumed model. This suggests that a basic assumption of previous theories, that increasing the load increases the number of contacts without affecting their average size, is redundant.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
The Friction and Lubrication of Solids
Bowden, F. P., Tabor, D., & Palmer, F. (1951) · American Journal of Physics · doi:10.1119/1.1933017 · Cited by 5,890
Cited by
The mechanics of earthquakes and faulting
(1990) · Choice Reviews Online · doi:10.5860/choice.28-1579 · Cited by 3,569
Leyland, A., & Matthews, A. (2000) · Wear · doi:10.1016/s0043-1648(00)00488-9 · Cited by 3,103
Mechanical behavior of high-entropy alloys
Li, W., Xie, D., Li, D., Zhang, Y., Gao, Y., & Liaw, P. K. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2021.100777 · Cited by 1,321
Tjong, S. C. (2013) · Materials Science and Engineering: R: Reports · doi:10.1016/j.mser.2013.08.001 · Cited by 1,155
Wear models and predictive equations: their form and content
Meng, H. C., & Ludema, K. C. (1995) · Wear · doi:10.1016/0043-1648(95)90158-2 · Cited by 970
The Mechanics of Earthquakes and Faulting
Scholz, C. H. (2019) · Cambridge University Press eBooks · doi:10.1017/9781316681473 · Cited by 910
Dorri Moghadam, A., Omrani, E., Menezes, P. L., & Rohatgi, P. K. (2015) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2015.03.014 · Cited by 906
Recent Progress on Wear‐Resistant Materials: Designs, Properties, and Applications
Zhai, W., Bai, L., Zhou, R., Fan, X., Kang, G., Liu, Y., & Zhou, K. (2021) · Advanced Science · doi:10.1002/advs.202003739 · Cited by 651
The effect of solid solution W additions on the mechanical properties of nanocrystalline Ni
Schuh, C. A., Nieh, T. G., & Iwasaki, H. (2003) · Acta Materialia · doi:10.1016/s1359-6454(02)00427-5 · Cited by 603
A review of recent advances in tribology
Meng, Y., Xu, J., Jin, Z., Prakash, B., & Hu, Y. (2020) · Friction · doi:10.1007/s40544-020-0367-2 · Cited by 594
Modeling and simulation in tribology across scales: An overview
Vakis, A. I., Yastrebov, V. A., Scheibert, J., Nicola, L., Dini, D., Minfray, C., Almqvist, A., Paggi, M., Lee, S., Limbert, G., et al. (2018) · Tribology International · doi:10.1016/j.triboint.2018.02.005 · Cited by 580
A review of vibration-based gear wear monitoring and prediction techniques
Feng, K., Ji, J. C., Ni, Q., & Beer, M. (2023) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2022.109605 · Cited by 545
Dynamic modeling of gearbox faults: A review
Liang, X., Zuo, M. J., & Feng, Z. (2018) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2017.05.024 · Cited by 534
Copper/graphene composites: a review
Hidalgo-Manrique, P., Lei, X., Xu, R., Zhou, M., Kinloch, I. A., & Young, R. J. (2019) · Journal of Materials Science · doi:10.1007/s10853-019-03703-5 · Cited by 393
The contribution of DEM to the science of comminution
Weerasekara, N. S., Powell, M. S., Cleary, P. W., Tavares, L. M., Evertsson, M., Morrison, R. D., Quist, J., & Carvalho, R. M. (2013) · Powder Technology · doi:10.1016/j.powtec.2013.05.032 · Cited by 372
Nanoscale wear as a stress-assisted chemical reaction
Jacobs, T. D. B., & Carpick, R. W. (2013) · Nature Nanotechnology · doi:10.1038/nnano.2012.255 · Cited by 361
Factors affecting enamel and ceramic wear: A literature review
Oh, W.-S., DeLong, R., & Anusavice, K. J. (2002) · The Journal of Prosthetic Dentistry · doi:10.1067/mpr.2002.123851 · Cited by 332
Critical length scale controls adhesive wear mechanisms
Aghababaei, R., Warner, D. H., & Molinari, J.-F. (2016) · Nature Communications · doi:10.1038/ncomms11816 · Cited by 326
PTFE Tribology and the Role of Mechanochemistry in the Development of Protective Surface Films
Harris, K. L., Pitenis, A. A., Sawyer, W. G., Krick, B. A., Blackman, G. S., Kasprzak, D. J., & Junk, C. P. (2015) · Macromolecules · doi:10.1021/acs.macromol.5b00452 · Cited by 326
Mechanical, corrosion, and wear properties of biomedical Ti–Zr–Nb–Ta–Mo high entropy alloys
Hua, N., Wang, W., Wang, Q., Ye, Y., Lin, S., Zhang, L., Guo, Q., Brechtl, J., & Liaw, P. K. (2021) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2020.157997 · Cited by 326
On the thermodynamic entropy of fatigue fracture
Naderi, M., Amiri, M., & Khonsari, M. M. (2010) · Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences · doi:10.1098/rspa.2009.0348 · Cited by 324
Modeling and simulation of wear in revolute clearance joints in multibody systems
Flores, P. (2009) · Mechanism and Machine Theory · doi:10.1016/j.mechmachtheory.2008.08.003 · Cited by 315
Physics guided neural network for machining tool wear prediction
Wang, J., Li, Y., Zhao, R., & Gao, R. X. (2020) · Journal of Manufacturing Systems · doi:10.1016/j.jmsy.2020.09.005 · Cited by 299
Ye, Y. X., Liu, C. Z., Wang, H., & Nieh, T. G. (2018) · Acta Materialia · doi:10.1016/j.actamat.2018.01.014 · Cited by 295
Karimzadeh, A., Aliofkhazraei, M., & Walsh, F. C. (2019) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2019.04.079 · Cited by 294
Oñate, E., & Rojek, J. (2004) · Computer Methods in Applied Mechanics and Engineering · doi:10.1016/j.cma.2003.12.056 · Cited by 289
Heterostructured stainless steel: Properties, current trends, and future perspectives
Romero-Resendiz, L., El-Tahawy, M., Zhang, T., Rossi, M. C., Marulanda-Cardona, D. M., Yang, T., Amigó-Borrás, V., Huang, Y., Mirzadeh, H., Beyerlein, I. J., et al. (2022) · Materials Science and Engineering: R: Reports · doi:10.1016/j.mser.2022.100691 · Cited by 278
Ultralow nanoscale wear through atom-by-atom attrition in silicon-containing diamond-like carbon
Bhaskaran, H., Gotsmann, B., Sebastian, A., Drechsler, U., Lantz, M. A., Despont, M., Jaroenapibal, P., Carpick, R. W., Chen, Y., & Sridharan, K. (2010) · Nature Nanotechnology · doi:10.1038/nnano.2010.3 · Cited by 257
Sustainability through alloy design: Challenges and opportunities
Cann, J. L., De Luca, A., Dunand, D. C., Dye, D., Miracle, D. B., Oh, H. S., Olivetti, E. A., Pollock, T. M., Poole, W. J., Yang, R., et al. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100722 · Cited by 191
BIKKINA, V., TALASILA, S. R., & ADEPU, K. (2020) · Transactions of Nonferrous Metals Society of China · doi:10.1016/s1003-6326(20)65335-3 · Cited by 34
Copper submicrospheres induced by pulsed laser-irradiation with enhanced tribology properties
Wang, L., Luo, T., Li, W., Wei, H., Chen, X., & Cao, B. (2019) · New Journal of Chemistry · doi:10.1039/c9nj03199e · Cited by 4
Metadata
- Authors
- Archard, J. F.
- Venue
- Journal of Applied Physics
- Publisher
- AIP Publishing
- Published
- 1953-08-01
- Volume
- 24
- Issue
- 8
- Pages
- 981-988
- ISSN
- 0021-8979 (ISSN-L)
- 1089-7550
- OpenAlex
- W1990351237
- Cited by
- 7,892
- References
- 1
- FWCI
- 20.42
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.