The DOI matches its Crossref record; 9 of the 9 references it cites were found in a registry or an index.
Effect of the printing bed temperature on the adhesion of parts produced by fused filament fabrication
Open accessAbstract
For parts produced by fused filament fabrication (FFF) the adhesion between the first printed layer and the printing bed is crucial, since it provides the foundation to the subsequent layers. Inadequate adhesion can result in poor printing quality or destroyed bed surfaces. This study aims at understanding and optimising the adhesion process for parts produced by FFF. The consequences of varying printing bed temperatures on the adhesion of two commonly used printing materials on two standard bed surfaces were investigated by means of an in-house built adhesion measurement device and complemented by contact angle measurements. This study shows a significant increase in adhesion forces, when printing parts at a bed temperature slightly above the glass transition temperature of the printing material.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Estimation of the surface free energy of polymers
Owens, D. K., & Wendt, R. C. (1969) · Journal of Applied Polymer Science · doi:10.1002/app.1969.070130815 · Cited by 9,476
Gibson, I., Rosen, D., & Stucker, B. (2015) · doi:10.1007/978-1-4939-2113-3 · Cited by 3,299
Awaja, F., Gilbert, M., Kelly, G., Fox, B., & Pigram, P. J. (2009) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2009.04.007 · Cited by 928
Fused deposition modeling with polypropylene
Carneiro, O. S., Silva, A. F., & Gomes, R. (2015) · Materials & Design · doi:10.1016/j.matdes.2015.06.053 · Cited by 851
Interface and chain confinement effects on the glass transition temperature of thin polymer films
Forrest, J. A., Dalnoki-Veress, K., & Dutcher, J. R. (1997) · Physical Review E · doi:10.1103/physreve.56.5705 · Cited by 804
Hashemi Sanatgar, R., Campagne, C., & Nierstrasz, V. (2017) · Applied Surface Science · doi:10.1016/j.apsusc.2017.01.112 · Cited by 368
Spoerk, M., Sapkota, J., Weingrill, G., Fischinger, T., Arbeiter, F., & Holzer, C. (2017) · Macromolecular Materials and Engineering · doi:10.1002/mame.201700143 · Cited by 169
Self-citationGaál, G., Mendes, M., de Almeida, T. P., Piazzetta, M. H. O., Gobbi, Â. L., Riul, A., & Rodrigues, V. (2016) · Sensors and Actuators B Chemical · doi:10.1016/j.snb.2016.10.110 · Cited by 156
Adhesion and Friction of Polystyrene Surfaces around T g
Zeng, H., Maeda, N., Chen, N., Tirrell, M., & Israelachvili, J. N. (2006) · Macromolecules · doi:10.1021/ma052207o · Cited by 91
Cited by
Extrusion-based additive manufacturing technologies: State of the art and future perspectives
Altıparmak, S. C., Yardley, V. A., Shi, Z., & Lin, J. (2022) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2022.09.032 · Cited by 320
Soliman, A., AlAmoodi, N., Karanikolos, G. N., Doumanidis, C. C., & Polychronopoulou, K. (2020) · Nanomaterials · doi:10.3390/nano10112198 · Cited by 53
Rais, M. H., Li, Y., & Ahmed, I. (2021) · Additive Manufacturing · doi:10.1016/j.addma.2021.102200 · Cited by 19
Ilhan, R., Gumus, O. Y., & Lekesiz, H. (2026) · Polymer Composites · doi:10.1002/pc.70459 · Cited by 5
Metadata
- Authors
- Spoerk, M., Gonzalez-Gutierrez, J., Sapkota, J., Schuschnigg, S., & Holzer, C.
- Venue
- Plastics, Rubber and Composites
- Publisher
- SAGE Publications
- Published
- 2017-11-08
- Volume
- 47
- Issue
- 1
- Pages
- 17-24
- ISSN
- 0959-8111 (ISSN-L)
- 1465-8011
- 1743-2898
- OpenAlex
- W2767528139
- Cited by
- 282
- References
- 9
- FWCI
- 10.18
- Type
- journal article
- Language
- en
- Open access
- hybrid
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Effect of the printing bed temperature on the adhesion of parts produced by fused filament fabrication. https://app.cochat.ai/papers/10.1080/14658011.2017.1399531
- The paper
- Spoerk, M., Gonzalez-Gutierrez, J., Sapkota, J., Schuschnigg, S., & Holzer, C. (2018). Effect of the printing bed temperature on the adhesion of parts produced by fused filament fabrication. Plastics, Rubber and Composites. https://doi.org/10.1080/14658011.2017.1399531
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.
