The DOI matches its Crossref record; 23 of the 23 references it cites were found in a registry or an index.
Microstructural characterization and properties of selective laser melted maraging steel with different build directions
Open accessAbstract
A nearly fully dense grade 300 maraging steel was fabricated by selective laser melting (SLM) additive manufacturing with optimum laser parameters. Different heat treatments were elaborately applied based on the detected phase transformation temperatures. Microstructures, precipitation characteristics, residual stress and properties of the as-fabricated and heat-treated SLM parts were systematically characterized and analyzed. The observed submicron grain size (0.31 μm on average) suggests an extremely high cooling rate up to 107 K/s. Massive needle-shaped nanoprecipitates Ni3X (X = Ti, Al, Mo) are clearly present in the martensitic matrix, which accounts for the age hardening. The interfacial relations between the precipitate and matrix are revealed by electron microscopy and illustrated in detail. Strengthening mechanism is explained by Orowan bowing mechanism and coherency strain hardening. Building orientation-based mechanical anisotropy, caused by ‘layer-wise effect’, is also investigated in as-fabricated and heat-treated specimens. The findings reveal that heat treatments not only induce strengthening, but also significantly relieve the residual stress and slightly eliminate the mechanical anisotropy. In addition, comprehensive performance in terms of Charpy impact test, tribological performance, as well as corrosion resistance of the as-fabricated and heat-treated parts are characterized and systematically investigated in comparison with traditionally produced maraging steels as guidance for industry applications.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Additive manufacturing of metals
Herzog, D., Seyda, V., Wycisk, E., & Emmelmann, C. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.07.019 · Cited by 4,759
Residual stresses in selective laser sintering and selective laser melting
Mercelis, P., & Kruth, J. (2006) · Rapid Prototyping Journal · doi:10.1108/13552540610707013 · Cited by 2,015
Olakanmi, E. O., Cochrane, R. F., & Dalgarno, K. W. (2015) · Progress in Materials Science · doi:10.1016/j.pmatsci.2015.03.002 · Cited by 1,742
Properties and Selection: Irons, Steels, and High-Performance Alloys
(1990) · ASM International eBooks · doi:10.31399/asm.hb.v01.9781627081610 · Cited by 964
Gorsse, S., Hutchinson, C., Gouné, M., & Banerjee, R. (2017) · Science and Technology of Advanced Materials · doi:10.1080/14686996.2017.1361305 · Cited by 920
Carter, L. N., Martin, C., Withers, P. J., & Attallah, M. M. (2014) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2014.06.172 · Cited by 751
Formation of metastable cellular microstructures in selective laser melted alloys
Prashanth, K. G., & Eckert, J. (2016) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2016.12.209 · Cited by 597
Microstructure and mechanical properties of Selective Laser Melted 18Ni-300 steel
Kempen, K., Yasa, E., Thijs, L., Kruth, J.-P., & Van Humbeeck, J. (2011) · Physics Procedia · doi:10.1016/j.phpro.2011.03.033 · Cited by 566
Tan, C., Zhou, K., Ma, W., Zhang, P., Liu, M., & Kuang, T. (2017) · Materials & Design · doi:10.1016/j.matdes.2017.08.026 · Cited by 546
Self-citationAl-saedi, D. S. J., Masood, S. H., Faizan‐Ur‐Rab, M., Alomarah, A., & Ponnusamy, P. (2018) · Materials & Design · doi:10.1016/j.matdes.2018.01.059 · Cited by 527
Cited by
Steels in additive manufacturing: A review of their microstructure and properties
Bajaj, P., Hariharan, A., Kini, A., Kürnsteiner, P., Raabe, D., & Jägle, E. A. (2020) · Materials Science and Engineering: A · doi:10.1016/j.msea.2019.138633 · Cited by 1,020
Additive manufacturing of steels: a review of achievements and challenges
Haghdadi, N., Laleh, M., Moyle, M., & Primig, S. (2021) · Journal of Materials Science · doi:10.1007/s10853-020-05109-0 · Cited by 622
Heat treatment for metal additive manufacturing
Laleh, M., Sadeghi, E., Revilla, R. I., Chao, Q., Haghdadi, N., Hughes, A. E., Xu, W., De Graeve, I., Qian, M., Gibson, I., et al. (2023) · Progress in Materials Science · doi:10.1016/j.pmatsci.2022.101051 · Cited by 538
Progress and perspectives in laser additive manufacturing of key aeroengine materials
Tan, C., Weng, F., Sui, S., Chew, Y., & Bi, G. (2021) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2021.103804 · Cited by 520
Self-citationNarasimharaju, S. R., Zeng, W., See, T. L., Zhu, Z., Scott, P., Jiang, X., & Lou, S. (2022) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2021.12.033 · Cited by 508
Metadata
- Authors
- Tan, C., Zhou, K., Kuang, M., Ma, W., & Kuang, T.
- Venue
- Science and Technology of Advanced Materials
- Publisher
- Informa UK Limited
- Published
- 2018-10-22
- Volume
- 19
- Issue
- 1
- Pages
- 746-758
- ISSN
- 1468-6996 (ISSN-L)
- 1878-5514
- OpenAlex
- W2898289031
- Cited by
- 264
- References
- 23
- FWCI
- 12.47
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Microstructural characterization and properties of selective laser melted maraging steel with different build directions. https://app.cochat.ai/papers/10.1080/14686996.2018.1527645
- The paper
- Tan, C., Zhou, K., Kuang, M., Ma, W., & Kuang, T. (2018). Microstructural characterization and properties of selective laser melted maraging steel with different build directions. Science and Technology of Advanced Materials. https://doi.org/10.1080/14686996.2018.1527645
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.