Detection of Localized Bearing Faults in Induction Machines by Spectral Kurtosis and Envelope Analysis of Stator Current
The DOI matches its Crossref record; 43 of the 43 references it cites were found in a registry or an index.
Abstract
Early detection of faults in electrical machines, particularly in induction motors, has become necessary and critical in reducing costs by avoiding unexpected and unnecessary maintenance and outages in industrial applications. Additionally, most of these faults are due to problems in bearings. Thus, in this paper, experimental bearing fault detection of a three-phase induction motor is performed by analyzing the squared envelope spectrum of the stator current. Spectral kurtosis-based algorithms, namely, the fast kurtogram and the wavelet kurtogram, are also applied to improve the envelope analysis. Experimental tests are performed, considering outer bearing faults at different stages, and the results are promising.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“Envelope analysis also was applied by Leite et al. [85] to detect the bearing fault in induction motor, and the proposed method can efficiently detect fault without any information regarding the model.”
From Vibration Analysis for Machine Monitoring and Diagnosis: A Systematic Review (2021) · cites this paper as [85]
Citations
Cites
Condition Monitoring and Fault Diagnosis of Electrical Motors—A Review
Nandi, S., Toliyat, H. A., & Li, X. (2005) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.2005.847955 · Cited by 2,382 · cited 1×
“In this case, the exact location of the defect is expressed by its characteristic frequency whose value can be predicted based on the rolling element bearing geometry, number of balls, and shaft speed [9], [22].”
BackgroundFast computation of the kurtogram for the detection of transient faults
Antoni, J. (2007) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2005.12.002 · Cited by 1,601 · cited 3×
“width in an efficient and computationally feasible way [31].”
BackgroundMethodThe spectral kurtosis: a useful tool for characterising non-stationary signals
Antoni, J. (2006) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2004.09.001 · Cited by 1,441 · cited 3×
“In this way, a time–frequency decomposition based on STFT is performed, and the kurtosis is computed in the time direction for each frequency line [11], [38].”
BackgroundMethodAdvances in Diagnostic Techniques for Induction Machines
Bellini, A., Filippetti, F., Tassoni, C., & Capolino, G.-A. (2008) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2008.2007527 · Cited by 1,140 · cited 3×
“In addition, the SNR can significantly vary in industrial applications [2].”
BackgroundVibration‐based Condition Monitoring: Industrial, Aerospace and Automotive Applications
Randall, R. B. (2011) · Wiley eBooks · doi:10.1002/9780470977668 · Cited by 868 · cited 10×
“In most cases, defects in the bearings are associated with contamination, corrosion, inadequate lubrication, and installation problems such as misalignment and overloading [1], [8]–[11].”
BackgroundMethodInfluentialMotor bearing damage detection using stator current monitoring
Schoen, R. R., Habetler, T. G., Kamran, F., & Bartfield, R. G. (1995) · IEEE Transactions on Industry Applications · doi:10.1109/28.475697 · Cited by 761
Barszcz, T., & JabŁoński, A. (2011) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2010.05.018 · Cited by 640 · cited 10×
“digital signal processing methods [11], [30].”
BackgroundMethodInfluentialMotor bearing damage detection using stator current monitoring
Schoen, R. R., Habetler, T. G., Kamran, F., & Bartheld, R. G. (2002) · Proceedings of 1994 IEEE Industry Applications Society Annual Meeting · doi:10.1109/ias.1994.345491 · Cited by 638 · cited 4×
“Here, artificially produced defects are introduced in the bearing outer race to simulate a localized fault, allowing the evaluation of the applied methodology and a critical comparison with other well-known techniques [13], [15], [22], [33], [43].”
BackgroundMethodResultInfluentialReport of Large Motor Reliability Survey of Industrial and Commercial Installations, Part I
(1985) · IEEE Transactions on Industry Applications · doi:10.1109/tia.1985.349532 · Cited by 602
Models for Bearing Damage Detection in Induction Motors Using Stator Current Monitoring
Blodt, M., Granjon, P., Raison, B., & Rostaing, G. (2008) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2008.917108 · Cited by 568
Fault Detection in Induction Machines Using Power Spectral Density in Wavelet Decomposition
Cusid�Cusido, J., Romeral, L., Ortega, J. A., Rosero, J. A., & Garc�aGarcia Espinosa, A. (2008) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2007.911960 · Cited by 512 · cited 1×
“form to detect faults in induction machines [25], [28], [29], [40].”
BackgroundPrieto, M. D., Cirrincione, G., Espinosa, A. G., Ortega, J. A., & Henao, H. (2013) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2012.2219838 · Cited by 461 · cited 2×
“monitoring mechanical faults [8], [10], [11], [16]–[20].”
BackgroundMotor Bearing Fault Diagnosis Using Trace Ratio Linear Discriminant Analysis
Jin, X., Zhao, M., Chow, T. W. S., & Pecht, M. (2014) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2013.2273471 · Cited by 423
Immovilli, F., Bellini, A., Rubini, R., & Tassoni, C. (2010) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2010.2049623 · Cited by 382
Cost-Effective Condition Monitoring for Wind Turbines
Yang, W., Tavner, P. J., Crabtree, C. J., & Wilkinson, M. (2010) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2009.2032202 · Cited by 344
Fault Diagnosis in Industrial Induction Machines Through Discrete Wavelet Transform
Bouzida, A., Touhami, O., Ibtiouen, R., Belouchrani, A., Fadel, M., & Rezzoug, A. (2011) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2010.2095391 · Cited by 325 · cited 1×
“form to detect faults in induction machines [25], [28], [29], [40].”
BackgroundA Probabilistic Fault Detection Approach: Application to Bearing Fault Detection
Zhang, B., Sconyers, C., Byington, C., Patrick, R., Orchard, M. E., & Vachtsevanos, G. (2011) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2010.2058072 · Cited by 269 · cited 2×
“entropy deconvolution, discrete random separation, and wavelet denoising, can also be used to enhance SK-based analysis in the bearing fault detection process [6], [11], [32], [42].”
MethodSoualhi, A., Clerc, G., & Razik, H. (2013) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2012.2230598 · Cited by 264
Frosini, L., & Bassi, E. (2010) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2009.2026770 · Cited by 254 · cited 9×
“Here, artificially produced defects are introduced in the bearing outer race to simulate a localized fault, allowing the evaluation of the applied methodology and a critical comparison with other well-known techniques [13], [15], [22], [33], [43].”
BackgroundMethodResultInfluentialMachine Condition Prediction Based on Adaptive Neuro–Fuzzy and High-Order Particle Filtering
Chen, C., Zhang, B., Vachtsevanos, G., & Orchard, M. (2011) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2010.2098369 · Cited by 250
Soualhi, A., Razik, H., Clerc, G., & Doan, D. D. (2014) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2013.2274415 · Cited by 213 · cited 2×
“Several studies have been made in this area [11], [20], [30], and in general, these algorithms aim to identify the characteristic”
BackgroundImmovilli, F., Cocconcelli, M., Bellini, A., & Rubini, R. (2009) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2009.2025288 · Cited by 201 · cited 3×
“The new band should also avoid maxima near the borders of the kurtogram [14].”
BackgroundBearing Fault Diagnosis for Direct-Drive Wind Turbines via Current-Demodulated Signals
Gong, X., & Qiao, W. (2013) · Industrial Electronics, IEEE Transactions on · doi:10.1109/tie.2013.2238871 · Cited by 195
Bearing Fault Model for Induction Motor With Externally Induced Vibration
Immovilli, F., Bianchini, C., Cocconcelli, M., Bellini, A., & Rubini, R. (2013) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2012.2213566 · Cited by 181
Bearing Condition Monitoring Methods for Electric Machines: A General Review
Zhou, W., Habetler, T. G., & Harley, R. G. (2007) · 2007 IEEE International Symposium on Diagnostics for Electric Machines, Power Electronics and Drives · doi:10.1109/demped.2007.4393062 · Cited by 174 · cited 7×
“In addition, the SNR can significantly vary in industrial applications [2].”
BackgroundInfluentialBearing Fault Detection Via Stator Current Noise Cancellation and Statistical Control
Zhou, W., Habetler, T. G., & Harley, R. G. (2008) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2008.2005018 · Cited by 165 · cited 3×
“In contrast, single-point defects are localized and can be classified according to their affected element [12].”
BackgroundPlastic Bearing Fault Diagnosis Based on a Two-Step Data Mining Approach
He, D., Li, R., & Zhu, J. (2012) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2012.2192894 · Cited by 143 · cited 2×
“Even in this context, it is important to point out that envelope analysis on vibration signals has been successfully used for decades for rolling element bearing fault detection [11], [19], [22], [29].”
BackgroundMethodPons-Llinares, J., Antonino-Daviu, J. A., Riera-Guasp, M., Pineda-Sanchez, M., & Climente-Alarcon, V. (2011) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2010.2081955 · Cited by 142 · cited 2×
“form to detect faults in induction machines [25], [28], [29], [40].”
BackgroundApplication of the Teager–Kaiser Energy Operator to the Fault Diagnosis of Induction Motors
Pineda‐Sanchez, M., Puche‐Panadero, R., Riera‐Guasp, M., Pérez‐Cruz, J., Roger-Folch, J., Pons-Llinares, J., Climente-Alarcón, V., & Daviu, J. A. A. (2013) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.2013.2279917 · Cited by 128 · cited 1×
“through stator current analysis, and over the past years, many works have been proposed following this methodology [12]– [15], [33], [34].”
BackgroundFault Detection of Linear Bearings in Brushless AC Linear Motors by Vibration Analysis
Bianchini, C., Immovilli, F., Cocconcelli, M., Rubini, R., & Bellini, A. (2011) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2010.2098354 · Cited by 126
Borghesani, P., Pennacchi, P., Ricci, R., & Chatterton, S. (2013) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2013.05.012 · Cited by 88 · cited 2×
“This square root operation inserts highfrequency components, and some of them might be aliased if their frequencies are higher than the Nyquist limit [32], [35].”
BackgroundBoukra, T., Lebaroud, A., & Clerc, G. (2013) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2012.2216242 · Cited by 88 · cited 1×
“entropy deconvolution, discrete random separation, and wavelet denoising, can also be used to enhance SK-based analysis in the bearing fault detection process [6], [11], [32], [42].”
MethodRobust Diagnosis of Rolling Element Bearings Based on Classification Techniques
Cococcioni, M., Lazzerini, B., & Volpi, S. L. (2012) · IEEE Transactions on Industrial Informatics · doi:10.1109/tii.2012.2231084 · Cited by 82 · cited 2×
“monitoring mechanical faults [8], [10], [11], [16]–[20].”
BackgroundPredictive maintenance techniques
Lu, B., Durocher, D., & Stemper, P. (2009) · IEEE Industry Applications Magazine · doi:10.1109/mias.2009.934444 · Cited by 82 · cited 3×
“In most cases, defects in the bearings are associated with contamination, corrosion, inadequate lubrication, and installation problems such as misalignment and overloading [1], [8]–[11].”
BackgroundMethodAntonino-Daviu, J., Aviyente, S., Strangas, E. G., & Riera-Guasp, M. (2013) · IEEE Transactions on Industrial Informatics · doi:10.1109/tii.2012.2198659 · Cited by 77
Filev, D., Chinnam, R. B., Tseng, F., & Baruah, P. (2010) · IEEE Transactions on Industrial Informatics · doi:10.1109/tii.2010.2060732 · Cited by 77
Millioz, F., & Martin, N. (2010) · IEEE Transactions on Signal Processing · doi:10.1109/tsp.2010.2081986 · Cited by 69 · cited 2×
“The SK will be positive in bands where the signal is present and, therefore, the energy is higher, but it will be zero for circular Gaussian variables [11], [38], [39].”
BackgroundHarmonic component detection: Optimized Spectral Kurtosis for operational modal analysis
Dion, J., Tawfiq, I., & Chevallier, G. (2011) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2011.07.009 · Cited by 48 · cited 1×
“Other methods of SK computation have also been presented in recent years [30], [36], [37], [41], but they are not part of this work.”
MethodStator current bi-spectrum patterns for induction machines multiple-faults detection
Saïdi, L., Fnaiech, F., Capolino, G., & Henao, H. (2012) · Annual Conference of the IEEE Industrial Electronics Society (IECON) · doi:10.1109/iecon.2012.6388975 · Cited by 25 · cited 2×
“In addition, the electrical signals of induction motors are, in the majority of cases, nonlinear, nonstationary, and non-Gaussian; therefore, the analysis of these signals with the use of higher order statistics is more convenient [11], [24].”
BackgroundApplication of spectral kurtosis to bearing fault detection in induction motors
Vrabie, V. D., Granjon, P., Maroni, C.-S., & Leprettre, B. (2004) · HAL · Cited by 13
Research on envelope analysis for bearings fault detection
Sui, W., & Zhang, D. (2010) · International Conference on Computer Science & Education (ICCSE) · doi:10.1109/iccse.2010.5593392 · Cited by 11 · cited 2×
“form to detect faults in induction machines [25], [28], [29], [40].”
BackgroundDetecting load failures using the induction motor as a transducer
Bonaldi, E. L., de Oliveira, L. E. L., da Silva, J. G. B., Lambert‐Torres, G., & da Silva, L. E. B. (2008) · International Conference on Control, Automation, Robotics and Vision (ICARCV) · doi:10.1109/icarcv.2008.4795516 · Cited by 8 · cited 1×
“In addition, the analysis can be done remotely and online, enabling the identification of several kinds of faults, including mechanical and load-related faults [2], [21], [24]–[28].”
BackgroundSelf-citationFault Diagnosis of Rolling Bearings Based on Wavelet Packet and Spectral Kurtosis
Tai-yong, W., & Lin, J. (2011) · International Conference on Intelligent Computation Technology and Automation · doi:10.1109/icicta.2011.173 · Cited by 7 · cited 2×
“rolling bearings [11], [14], [30]–[32], [36], [37].”
Method
Research works printed but not linked: 1
- sawalhi, 2007, Diagnostics prognostics and fault simulation for rolling element bearings
Cited by
Feature Mode Decomposition: New Decomposition Theory for Rotating Machinery Fault Diagnosis
Miao, Y., Zhang, B., Li, C., Lin, J., & Zhang, D. (2023) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2022.3156156 · Cited by 495
“The most-used methods include spectrum kurtosis [4], sparse filtering [5], deconvolution [6], etc.”
MethodTian, J., Morillo, C., Azarian, M. H., & Pecht, M. (2016) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2015.2509913 · Cited by 488
“implemented for bearing damage detection using vibration and motor current signals [24]–[26].”
BackgroundSaidi, L., Ben Ali, J., Bechhoefer, E., & Benbouzid, M. (2017) · Applied Acoustics · doi:10.1016/j.apacoust.2017.01.005 · Cited by 252
Qin, Y. (2018) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2017.2736510 · Cited by 250
“The spectral kurtosis (SK) may be the most widely used method for bearing fault detection [13], [17], [18].”
MethodVibration Analysis for Machine Monitoring and Diagnosis: A Systematic Review
Mohd Ghazali, M. H., & Rahiman, W. (2021) · Shock and Vibration · doi:10.1155/2021/9469318 · Cited by 249
“[85] to detect the bearing fault in induction motor, and the proposed method can efficiently detect fault without any information regarding the model.”
Method
Metadata
- Authors
- Leite, V. C. M. N., Borges da Silva, J. G., Veloso, G. F. C., Borges da Silva, L. E., Lambert-Torres, G., Bonaldi, E. L., & de Lacerda de Oliveira, L. E.
- Affiliations
- Department of Aerospace Science and Technology (BR)
- Universidade Federal de Itajubá (BR)
- Venue
- IEEE Transactions on Industrial Electronics
- Published
- 2015-03
- Volume
- 62
- Issue
- 3
- Pages
- 1855-1865
- ISSN
- 0278-0046 (ISSN-L)
- 1557-9948
- OpenAlex
- W1993880634
- Cited by
- 274
- References
- 43
- Citations by year
- 2026: 5 · 2025: 15 · 2024: 21 · 2023: 21 · 2022: 23 · 2021: 32 · 2020: 29 · 2019: 33 · 2018: 33 · 2017: 26 · 2016: 21 · 2015: 14
- FWCI
- 23.05
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- IEEE Transactions on Industrial Electronics (publishedVersion)
- Topics
- Physical Sciences › Engineering › Control and Systems Engineering › Machine Fault Diagnosis Techniques
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Electric Motor Design and Analysis
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Electrical Fault Detection and Protection
- Keywords
- bearing fault detection, induction motor, stator current, spectral kurtosis, envelope analysis, fast kurtogram, condition monitoring, fault location
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.