Detection of Localized Bearing Faults in Induction Machines by Spectral Kurtosis and Envelope Analysis of Stator Current
The DOI matches its Crossref record; 43 of the 43 references it cites were found in a registry or an index.
Abstract
Early detection of faults in electrical machines, particularly in induction motors, has become necessary and critical in reducing costs by avoiding unexpected and unnecessary maintenance and outages in industrial applications. Additionally, most of these faults are due to problems in bearings. Thus, in this paper, experimental bearing fault detection of a three-phase induction motor is performed by analyzing the squared envelope spectrum of the stator current. Spectral kurtosis-based algorithms, namely, the fast kurtogram and the wavelet kurtogram, are also applied to improve the envelope analysis. Experimental tests are performed, considering outer bearing faults at different stages, and the results are promising.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“Envelope analysis also was applied by Leite et al. [85] to detect the bearing fault in induction motor, and the proposed method can efficiently detect fault without any information regarding the model.”
From Vibration Analysis for Machine Monitoring and Diagnosis: A Systematic Review (2021) · cites this paper as [85]
Citations
Cites
Condition Monitoring and Fault Diagnosis of Electrical Motors—A Review
Nandi, S., Toliyat, H. A., & Li, X. (2005) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.2005.847955 · Cited by 2,382 · cited 1×
“In this case, the exact location of the defect is expressed by its characteristic frequency whose value can be predicted based on the rolling element bearing geometry, number of balls, and shaft speed [9], [22].”
BackgroundFast computation of the kurtogram for the detection of transient faults
Antoni, J. (2007) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2005.12.002 · Cited by 1,601 · cited 3×
“width in an efficient and computationally feasible way [31].”
BackgroundMethodThe spectral kurtosis: a useful tool for characterising non-stationary signals
Antoni, J. (2006) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2004.09.001 · Cited by 1,441 · cited 3×
“In this way, a time–frequency decomposition based on STFT is performed, and the kurtosis is computed in the time direction for each frequency line [11], [38].”
BackgroundMethodAdvances in Diagnostic Techniques for Induction Machines
Bellini, A., Filippetti, F., Tassoni, C., & Capolino, G.-A. (2008) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2008.2007527 · Cited by 1,140 · cited 3×
“In addition, the SNR can significantly vary in industrial applications [2].”
BackgroundVibration‐based Condition Monitoring: Industrial, Aerospace and Automotive Applications
Randall, R. B. (2011) · Wiley eBooks · doi:10.1002/9780470977668 · Cited by 868 · cited 10×
“In most cases, defects in the bearings are associated with contamination, corrosion, inadequate lubrication, and installation problems such as misalignment and overloading [1], [8]–[11].”
BackgroundMethodInfluentialMotor bearing damage detection using stator current monitoring
Schoen, R. R., Habetler, T. G., Kamran, F., & Bartfield, R. G. (1995) · IEEE Transactions on Industry Applications · doi:10.1109/28.475697 · Cited by 761
Barszcz, T., & JabŁoński, A. (2011) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2010.05.018 · Cited by 640 · cited 10×
“digital signal processing methods [11], [30].”
BackgroundMethodInfluentialMotor bearing damage detection using stator current monitoring
Schoen, R. R., Habetler, T. G., Kamran, F., & Bartheld, R. G. (2002) · Proceedings of 1994 IEEE Industry Applications Society Annual Meeting · doi:10.1109/ias.1994.345491 · Cited by 638 · cited 4×
“Here, artificially produced defects are introduced in the bearing outer race to simulate a localized fault, allowing the evaluation of the applied methodology and a critical comparison with other well-known techniques [13], [15], [22], [33], [43].”
BackgroundMethodResultInfluentialReport of Large Motor Reliability Survey of Industrial and Commercial Installations, Part I
(1985) · IEEE Transactions on Industry Applications · doi:10.1109/tia.1985.349532 · Cited by 602
Models for Bearing Damage Detection in Induction Motors Using Stator Current Monitoring
Blodt, M., Granjon, P., Raison, B., & Rostaing, G. (2008) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2008.917108 · Cited by 568
Research works printed but not linked: 1
- sawalhi, 2007, Diagnostics prognostics and fault simulation for rolling element bearings
Cited by
Feature Mode Decomposition: New Decomposition Theory for Rotating Machinery Fault Diagnosis
Miao, Y., Zhang, B., Li, C., Lin, J., & Zhang, D. (2023) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2022.3156156 · Cited by 495
“The most-used methods include spectrum kurtosis [4], sparse filtering [5], deconvolution [6], etc.”
MethodTian, J., Morillo, C., Azarian, M. H., & Pecht, M. (2016) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2015.2509913 · Cited by 488
“implemented for bearing damage detection using vibration and motor current signals [24]–[26].”
BackgroundSaidi, L., Ben Ali, J., Bechhoefer, E., & Benbouzid, M. (2017) · Applied Acoustics · doi:10.1016/j.apacoust.2017.01.005 · Cited by 252
Qin, Y. (2018) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2017.2736510 · Cited by 250
“The spectral kurtosis (SK) may be the most widely used method for bearing fault detection [13], [17], [18].”
MethodVibration Analysis for Machine Monitoring and Diagnosis: A Systematic Review
Mohd Ghazali, M. H., & Rahiman, W. (2021) · Shock and Vibration · doi:10.1155/2021/9469318 · Cited by 249
“[85] to detect the bearing fault in induction motor, and the proposed method can efficiently detect fault without any information regarding the model.”
MethodNonconvex Sparse Regularization and Convex Optimization for Bearing Fault Diagnosis
Wang, S., Selesnick, I., Cai, G., Feng, Y., Sui, X., & Chen, X. (2018) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2018.2793271 · Cited by 247
“After bearing fault signals are extracted, an envelope spectrum is calculated to indicate bearing faults by comparing the fault characteristic frequencies [17], [18].”
MethodEnhanced Sparse Period-Group Lasso for Bearing Fault Diagnosis
Zhao, Z., Wu, S., Qiao, B., Wang, S., & Chen, X. (2019) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2018.2838070 · Cited by 234
“Spectral kurtosis (SK) [9]–[11] as a filter-based method is aimed to adaptively search the suitable resonance frequency band.”
MethodYang, B., Liu, R., & Chen, X. (2017) · IEEE Transactions on Industrial Informatics · doi:10.1109/tii.2017.2662215 · Cited by 218
“Harmonic components spread all over the vibration signal and can cause modulation effect on the impact component and, consequently, influence the result of impulsive feature extraction, which is a fundamental transient phenomenon that always modeled as dynamic response of abnormal operations when the generator develop…”
BackgroundAhmad, W., Khan, S. A., Islam, M. M. M., & Kim, J.-M. (2019) · Reliability Engineering & System Safety · doi:10.1016/j.ress.2018.02.003 · Cited by 216
A Hybrid Prognostics Technique for Rolling Element Bearings Using Adaptive Predictive Models
Ahmad, W., Khan, S. A., & Kim, J.-M. (2018) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2017.2733487 · Cited by 212
SuperGraph: Spatial-Temporal Graph-Based Feature Extraction for Rotating Machinery Diagnosis
Yang, C., Zhou, K., & Liu, J. (2022) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2021.3075871 · Cited by 183
“Among these, spectrum analysis, which mainly includes Fourier spectrum analysis, power spectrum analysis [8], cyclic spectrum [9], holospectrum analysis [10], and envelop spectrum analysis [11], has been widely used and proved to be effective for extracting fault information from vibration signals.”
MethodBasic research on machinery fault diagnostics: Past, present, and future trends
Chen, X., Wang, S., Qiao, B., & Chen, Q. (2018) · Frontiers of Mechanical Engineering · doi:10.1007/s11465-018-0472-3 · Cited by 162
Liu, Y., & Bazzi, A. M. (2017) · ISA Transactions · doi:10.1016/j.isatra.2017.06.001 · Cited by 159
An Efficient Hilbert–Huang Transform-Based Bearing Faults Detection in Induction Machines
Elbouchikhi, E., Choqueuse, V., Amirat, Y., Benbouzid, M., & Turri, S. (2017) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.2017.2661541 · Cited by 153
“Hence, most of the recent researches on induction machine faults detection have been directed toward electrical monitoring with emphasis on stator current analysis [6]–[8].”
BackgroundLi, J., Zhang, J., Li, M., & Zhang, Y. (2018) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2018.05.004 · Cited by 146
Maheswari, R., & Umamaheswari, R. (2016) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2016.07.046 · Cited by 152
Manohar, M., & Das, S. (2017) · IEEE Transactions on Industrial Informatics · doi:10.1109/tii.2017.2714675 · Cited by 146
“Other causes of machine failures are mechanical fault in rotor [6], such as rotor bearing fault [7], bent shaft, air-gap eccentricity, and rotor misalignment [8].”
BackgroundModern Diagnostics Techniques for Electrical Machines, Power Electronics, and Drives
Capolino, G.-A., Antonino-Daviu, J. A., & Riera-Guasp, M. (2015) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2015.2391186 · Cited by 104
“In [16], a methodology for diagnosing localized defects in”
MethodSoualhi, M., Nguyen, K. T. P., Soualhi, A., Medjaher, K., & Hemsas, K. E. (2019) · Measurement · doi:10.1016/j.measurement.2019.03.065 · Cited by 105
Temporal-Spatio Graph Based Spectrum Analysis for Bearing Fault Detection and Diagnosis
Wang, T., Liu, Z., Lu, G., & Liu, J. (2020) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2020.2975499 · Cited by 105
“Representative methods include Fourier spectrum analysis, power spectrum analysis [7], envelop spectrum analysis [8], holospectrum analysis [9], cyclic spectrum analysis [10], etc.”
MethodNguyen, K. T. P., Medjaher, K., & Tran, T.-D. (2022) · Artificial Intelligence Review · doi:10.1007/s10462-022-10260-y · Cited by 126
Maruthi, G. S., & Hegde, V. (2015) · IEEE Sensors Journal · doi:10.1109/jsen.2015.2476561 · Cited by 99
“The spectral kurtosis and envelope analysis of stator current in [8] and statistical processing of the stray flux measurement in [9] are employed to detect localized bearing faults.”
BackgroundMethodPandarakone, S. E., Mizuno, Y., & Nakamura, H. (2016) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2016.2639453 · Cited by 103
“[22] carried out an experiment for holes of diameter 2.”
BackgroundMethodSantos, M. R., Guedes, L. A., & Sánchez-Gendriz, I. (2024) · Machine Learning and Knowledge Extraction · doi:10.3390/make6010016 · Cited by 107
“In the realm of time-frequency techniques, notable methods include the short-time Fourier transform (STFT) [42–44], discrete wavelet transform (DWT) [45–50], envelope analysis [2,51–53], and empirical mode decomposition (EMD) [54–57].”
MethodA Review on Rolling Bearing Fault Signal Detection Methods Based on Different Sensors
Wu, G., Yan, T., Yang, G., Chai, H., & Cao, C. (2022) · Sensors · doi:10.3390/s22218330 · Cited by 112
“In addition, by analyzing the square envelope spectrum of stator current, experimental bearing fault detection of a three-phase induction motor was carried out (Leite et al., 2015) [62].”
MethodLyu, P., Zhang, K., Yu, W., Wang, B., & Liu, C. (2022) · Advanced Engineering Informatics · doi:10.1016/j.aei.2022.101564 · Cited by 92
Current Noise Cancellation for Bearing Fault Diagnosis Using Time Shifting
Dalvand, F., Dalvand, S., Sharafi, F., & PECHT, M. G. (2017) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2017.2694397 · Cited by 84
“B EARING faults are the major contributors to the failure of IMs, which can lead to motor breakdown, equipment defects, and even human casualties [1]–[3].”
BackgroundMethodInfluentialPandarakone, S. E., Mizuno, Y., & Nakamura, H. (2019) · Energies · doi:10.3390/en12112105 · Cited by 94
“Many studies have performed bearing failure analysis considering a hole [19] as a faulty factor.”
BackgroundAn Efficient Stator Inter-Turn Fault Diagnosis Tool for Induction Motors
Maraaba, L. S., Al‐Hamouz, Z., & Abido, M. A. (2018) · Energies · doi:10.3390/en11030653 · Cited by 82
“Mechanical faults include bearing damage and shaft defects [9].”
BackgroundSaucedo-Dorantes, J. J., Delgado-Prieto, M., Ortega-Redondo, J. A., Osornio-Rios, R. A., & Romero-Troncoso, R. D. J. (2016) · Shock and Vibration · doi:10.1155/2016/5467643 · Cited by 80
Akbar, S., Vaimann, T., Asad, B., Kallaste, A., Sardar, M. U., & Kudelina, K. (2023) · Energies · doi:10.3390/en16176345 · Cited by 103
Chen, X., Xu, W., Liu, Y., & Islam, M. R. (2019) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2019.2917418 · Cited by 77
“, the spectral Kurtosis algorithm [10], the Welch power spectrum analysis [17], the root-MUSIC method [18] and noise cancellation [19].”
Chen, G., Liu, M., & Chen, J. (2020) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2020.106951 · Cited by 85
Investigations on quasi-arithmetic means for machine condition monitoring
Hou, B., Wang, D., Xia, T., Wang, Y., Zhao, Y., & Tsui, K. (2020) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2020.107451 · Cited by 78
Sapena-Bañó, Á., Burriel-Valencia, J., Pineda‐Sanchez, M., Puche‐Panadero, R., & Riera‐Guasp, M. (2016) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.2016.2626008 · Cited by 86
“Table I shows the characteristic frequencies of the amplitude modulation (ff ) and the sidebands in the stator current spectrum (fsb) due to rotor broken bars [6], [7] eccentricity [8], [9], [10] and bearing faults [11], [12], where k = ±1, ±2, ±3, .”
BackgroundBearing Fault Classification Based on Convolutional Neural Network in Noise Environment
Jiang, Q., Chang, F., & Sheng, B. (2019) · IEEE Access · doi:10.1109/access.2019.2919126 · Cited by 80
“The spectral version of kurtosis, SK, is the kurtosis computed at the output of a perfect filter-bank at each frequency band [8], and it is commonly defined as the normalized fourth-order cumulate of the Fourier transform [21].”
BackgroundYau, H., Wu, S., Chen, C., & Li, Y. (2016) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2016.2522941 · Cited by 72
“Recent research on the diagnosis of bearing faults mainly involves the extraction of a stator current [1]–[3], an audio signal [4], [5], or a vibration signal [6], [7].”
BackgroundHan, Q., Ding, Z., Xu, X., Wang, T., & Chu, F. (2019) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2019.06.010 · Cited by 78
The Bearing Faults Detection Methods for Electrical Machines—The State of the Art
Khan, M. A., Asad, B., Kudelina, K., Vaimann, T., & Kallaste, A. (2022) · Energies · doi:10.3390/en16010296 · Cited by 89
Mueller, P. N. (2024) · Engineering Applications of Artificial Intelligence · doi:10.1016/j.engappai.2023.107696 · Cited by 84
Brusamarello, B., da Silva, J. C. C., Sousa, K. D. M., & Guarneri, G. A. (2022) · IEEE Sensors Journal · doi:10.1109/jsen.2022.3167632 · Cited by 86
Dalvand, F., Kang, M., Dalvand, S., & PECHT, M. G. (2018) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2018.2821645 · Cited by 70
“In [3] and [11], it was experimentally shown that the impacts of the single-point and generalized-roughness bearing faults have similar statistical properties in stator current and vibration signals.”
BackgroundMethodInfluentialHong, Y., Kim, M., Lee, H., Park, J. J., & Lee, D. (2019) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/tim.2019.2898050 · Cited by 69
“SK offers an efficient way of detecting incipient faults, even in very noisy environments [5]–[7].”
BackgroundNovel Diagnostic Techniques for Rotating Electrical Machines—A Review
Frosini, L. (2020) · Energies · doi:10.3390/en13195066 · Cited by 67
“Moreover, the fast kurtogram algorithm has been proved effective in identifying the frequency bands in which the fault impulses are concentrated [97].”
MethodEEMD-based notch filter for induction machine bearing faults detection
Amirat, Y., Benbouzid, M., Wang, T., Bacha, K., & Feld, G. (2017) · Applied Acoustics · doi:10.1016/j.apacoust.2017.12.030 · Cited by 68
Miao, Y., Zhao, M. J., & Lin, J. (2018) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2018.2844792 · Cited by 66
“Therefore, to eliminate unscheduled breakdowns and unnecessary costs caused by motor bearing failures, timely and reliable detection of the incipient bearing fault is significant [5], [6].”
BackgroundA Novel Weak Signal Detection Method via Chaotic Synchronization Using Chua's Circuit
Li, G., & Zhang, B. (2016) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2016.2620103 · Cited by 64
“THERE is a great demand for, and wide use of, weak sinusoidal signal detection [1], [2].”
BackgroundLi, J., Yu, Q., Wang, X., & Zhang, Y. (2020) · ISA Transactions · doi:10.1016/j.isatra.2020.02.031 · Cited by 63
Rolling Bearing Fault Diagnosis Based on an Improved HTT Transform
Pang, B., Tang, G., Tian, T., & Zhou, C. (2018) · Sensors · doi:10.3390/s18041203 · Cited by 64
“transform (HT) envelope spectrum [16], bisepctrum [17], Teager energy spectrum [18], and spectral kurtosis (SK) [19].”
BackgroundRotating Machinery Fault Diagnosis Based on Typical Resonance Demodulation Methods: A Review
Li, H., Wu, X. F., Liu, T., & Li, S. (2023) · IEEE Sensors Journal · doi:10.1109/jsen.2023.3235585 · Cited by 61
“[46] presented an algorithm based on SK, namely, fast kurtogram and wavelet kurtogram to improve envelope analysis, which was used to analyze the current signal to realize the experimental bearing fault detection of three-”
MethodAutocorrelation function‐based technique for stator turn‐fault detection of induction motor
Ghanbari, T. (2015) · IET Science Measurement & Technology · doi:10.1049/iet-smt.2015.0118 · Cited by 62
Ahmed, H., & Nandi, A. K. (2018) · IEEE Access · doi:10.1109/access.2018.2865116 · Cited by 65
Nguyen, K. T. P., & Medjaher, K. (2020) · ISA Transactions · doi:10.1016/j.isatra.2020.03.017 · Cited by 60
Dalvand, F., Kalantar, A., & Safizadeh, M. S. (2015) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2015.2464294 · Cited by 71
“To detect bearing faults of IMs, many diagnostic methods based on variables such as vibration, motor current, power factor, sound pressure, acoustic emission, torque, stray flux, and temperature have been applied in previous works [2], [4], [9], [11]–[27].”
BackgroundMethodInfluentialWang, L., & Shao, Y.-M. (2018) · Chinese Journal of Mechanical Engineering · doi:10.1186/s10033-018-0202-0 · Cited by 61
Analytic Model for Induction Motors Under Localized Bearing Faults
Ojaghi, M., Sabouri, M., & Faiz, J. (2017) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.2017.2758382 · Cited by 64
“In [10], the bearing fault detection of a three-phase induction motor was performed by analyzing the squared envelope”
MethodWen, X., Lu, G., Liu, J., & Yan, P. (2020) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2020.106956 · Cited by 57
Gao, Q., Xiang, J., Hou, S., Tang, H., Zhong, Y., & Ye, S. (2020) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2020.107130 · Cited by 53
Varanis, M. V. M., Silva, A., Balthazar, J. M., & Pederiva, R. (2021) · Brazilian Journal of Physics · doi:10.1007/s13538-020-00842-y · Cited by 52
Gritli, Y., Bellini, A., Rossi, C., Casadei, D., Filippetti, F., & Capolino, G. (2017) · IEEE International Symposium on Diagnostics for Electrical Machines, Power Electronics and Drives (SDEMPED) · doi:10.1109/demped.2017.8062337 · Cited by 57
Cloud-Manufacturing-Based Condition Monitoring Platform With 5G and Standard Information Model
Yang, H., Sun, Z., Jiang, G., Zhao, F., Lu, X., & Mei, X. (2020) · IEEE Internet of Things Journal · doi:10.1109/jiot.2020.3036870 · Cited by 57
“Currently, considerable attention has been paid to the diagnosis [14], [15] and prognosis [16], [17] methods, while the cloud-based CM remains a challenge considering edge-fog computing, data modeling, and cloud monitoring platform (CMP) construction.”
BackgroundMueller, P. N., Woelfl, L., & Can, S. (2023) · Engineering Applications of Artificial Intelligence · doi:10.1016/j.engappai.2023.106834 · Cited by 58
Barusu, M. R., & Deivasigamani, M. (2020) · IEEE Sensors Journal · doi:10.1109/jsen.2020.3004515 · Cited by 55
“The FFT is not appropriate to analyze a non-stationary signal and required long acquisition time, results in the change of fault spectrum [32], [40], [50].”
MethodInfluentialYang, M., Chai, N., Liu, Z., Ren, B., & Xu, D. (2019) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2019.2922919 · Cited by 49
“To demonstrate the superiority of the proposed strategy, a comparative study among it, SK of speed signal without suppression, SK of stator current [14], TS of stator current [16],”
MethodCurrent-Based Bearing Fault Diagnosis Using Deep Learning Algorithms
Barcelos, A. D. S., & Cardoso, A. J. M. (2021) · Energies · doi:10.3390/en14092509 · Cited by 54
“The vibration data acquisition is also expensive, demanding new sensors and devices to transduce, transmit and process [3].”
BackgroundA Wavelet-Based Fault Diagnosis Approach for Permanent Magnet Synchronous Motors
Heydarzadeh, M., Zafarani, M., Nourani, M., & Akin, B. (2018) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.2018.2864570 · Cited by 54
Quaternion Signal Analysis Algorithm for Induction Motor Fault Detection
Contreras-Hernandez, J. L., Almanza-Ojeda, D.-L., Ledesma, S., García-Pérez, A., Romero-Troncoso, R. D. J., & Ibarra-Manzano, M.-A. (2019) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2019.2891468 · Cited by 48
“Similarly, spectral kurtosis-based algorithms are used to find faults in the bearing elements by using the stator current or the vibration signal to analyze the characteristic frequencies [5], [6].”
Hou, B., Wang, D., Peng, Z., & Tsui, K. (2023) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2023.3243282 · Cited by 50
“In various machinery equipment, rotating parts, including bearings and gears, are most probable to have localized faults because these parts are used for bearing weight and transmitting force and moment [7], [8], [9].”
BackgroundMing, A., We, Z., Qin, Z., & Chu, F. (2015) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2015.2463767 · Cited by 47
Attention-Based Bilinear Feature Fusion Method for Bearing Fault Diagnosis
Wang, D., Li, Y., Jia, L., Song, Y., & Wen, T. (2022) · IEEE/ASME Transactions on Mechatronics · doi:10.1109/tmech.2022.3223358 · Cited by 46
“Leite et al. proposed a fault detection method for the bearing of a three-phase induction motor by using the squared envelope spectrum of the stator current [23].”
MethodElbouchikhi, E., Choqueuse, V., & Benbouzid, M. (2016) · ISA Transactions · doi:10.1016/j.isatra.2016.03.007 · Cited by 46
A fault pulse extraction and feature enhancement method for bearing fault diagnosis
Chen, Z., Guo, L., Gao, H., Yu, Y., Wu, W., You, Z., & Dong, X. (2021) · Measurement · doi:10.1016/j.measurement.2021.109718 · Cited by 47
Analysis of Diagnostic Methods and Energy of Production Systems Drives
Kuric, I., Klačková, I., Nikitin, Y. P., Zajačko, I., Císar, M., & Tucki, K. (2021) · Processes · doi:10.3390/pr9050843 · Cited by 49
Low Complexity Motor Current Signature Analysis Using Sub-Nyquist Strategy With Reduced Data Length
Naha, A., Samanta, A. K., Routray, A., & Deb, A. K. (2017) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/tim.2017.2737879 · Cited by 43
Pandarakone, S. E., Mizuno, Y., & Nakamura, H. (2018) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2018.2833025 · Cited by 49
“Widely used techniques include squared envelope analysis [22], spectral kurtosis analysis [23], the wavelet kurtogram [24], root mean square [25] analysis, high-order statistical methods [26], and the short impulse method [27].”
MethodCross-correlation of whitened vibration signals for low-speed bearing diagnostics
Klausen, A., & Robbersmyr, K. G. (2018) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2018.08.048 · Cited by 43
Liu, X., Sun, W. F., Li, H., Wang, Z., & Li, Q. (2022) · IEEE Sensors Journal · doi:10.1109/jsen.2022.3222535 · Cited by 42
“5 and 13, kinds of generating samples are similar to real data both in time and frequency domains.”
BackgroundGuan, B., Bao, X., Qiu, H., & Yang, D. (2023) · Measurement · doi:10.1016/j.measurement.2023.114049 · Cited by 55
Maraaba, L. S., Al‐Hamouz, Z., Milhem, A. S., & Abido, M. A. (2019) · IEEE Access · doi:10.1109/access.2019.2923746 · Cited by 41
“Among these indicators are the magnetic flux, the vibration, the stator current (a negative and zero sequence or a third harmonic component), the zero-sequence component of the voltage, the thermal image, the instantaneous real and reactive power, the phase shift between the stator current and the supply voltage and t…”
BackgroundMulti-band identification for enhancing bearing fault detection in variable speed conditions
Klausen, A., Khang, H. V., & Robbersmyr, K. G. (2019) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2019.106422 · Cited by 41
An Efficient Fault Detection Method for Induction Motors Using Thermal Imaging and Machine Vision
Javed, M. R., Shabbir, Z., Asghar, F., Amjad, W., Mahmood, F., Khan, M. O., Virk, U. S., Waleed, A., & Haider, Z. M. (2022) · Sustainability · doi:10.3390/su14159060 · Cited by 38
Data-driven approaches for impending fault detection of industrial systems: a review
Patil, A., Soni, G., & Prakash, A. (2022) · International Journal of Systems Assurance Engineering and Management · doi:10.1007/s13198-022-01841-9 · Cited by 49
“Hilbert envelope analysis is applied frequently for identifying defects generated due to cyclic shocks in rolling element bearings (Leite et al. 2015).”
Zheng, K. W., Yang, D., Zhang, B., Xiong, J., Luo, J., & Dong, Y. (2019) · Journal of Sound and Vibration · doi:10.1016/j.jsv.2019.114931 · Cited by 36
Bazan, G. H., Scalassara, P. R., Endo, W., & Goedtel, A. (2019) · IEEE Transactions on Industrial Informatics · doi:10.1109/tii.2019.2939678 · Cited by 45
“tests, in [2], [5], [6], and [40]–[42], the authors did not present statistical analysis, only graphical representations of the results.”
BackgroundMethodInfluentialA Diagnosis Method of Bearing and Stator Fault in Motor Using Rotating Sound Based on Deep Learning
Nakamura, H., Asano, K., Usuda, S., & Mizuno, Y. (2021) · Energies · doi:10.3390/en14051319 · Cited by 39
“[12] used the holes with a diameter of 2.”
BackgroundMethodCompound fault diagnosis of rolling bearing using PWK-sparse denoising and periodicity filtering
Meng, J., Wang, H., Zhao, L., & Yan, R. (2021) · Measurement · doi:10.1016/j.measurement.2021.109604 · Cited by 35
Sardar, M. U., Vaimann, T., Kütt, L., Kallaste, A., Asad, B., Akbar, S., & Kudelina, K. (2023) · Energies · doi:10.3390/en16155628 · Cited by 50
Nakamura, H., & Mizuno, Y. (2022) · Energies · doi:10.3390/en15020453 · Cited by 38
Bazan, G. H., Goedtel, A., Duque-Pérez, Ó., & Moríñigo-Sotelo, D. (2021) · Electronics · doi:10.3390/electronics10121462 · Cited by 36
“The bearing failures are usually the result of contamination, corrosion, inadequate lubrication, and installation problems, such as misalignment and overload [7].”
BackgroundAnalysis and comparison of multiple features for fault detection and prognostic in ball bearings
Nguyen, K. T. P., Amor, K., Medjaher, K., Picot, A., Maussion, P., Tobon-Mejia, D. A., Chauchat, B., & Cheron, R. (2018) · PHM Society European Conference · doi:10.36001/phme.2018.v4i1.435 · Cited by 32
Liu, D., Cheng, W., & Wen, W. (2019) · IEEE Systems Journal · doi:10.1109/jsyst.2019.2929617 · Cited by 32
Lee, C., & Le, T. (2021) · IEEE Access · doi:10.1109/access.2021.3083646 · Cited by 31
“Although there are many improvements in this approach [3], the model performance will be affected when the measured signal is strongly disturbed [4].”
BackgroundEffect of Magnets Asymmetry on Stray Magnetic Flux Based Bearing Damage Detection in PMSM
Gurusamy, V., Baruti, K. H., Zafarani, M., Lee, W., & Akin, B. (2021) · IEEE Access · doi:10.1109/access.2021.3076779 · Cited by 28
Kang, M., Kim, J., Jeong, I.-K., Kim, J.-M., & PECHT, M. G. (2016) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2016.2574986 · Cited by 30
Liu, Y., Chai, Y., Liu, B., & Wang, Y. (2021) · Sensors · doi:10.3390/s21062245 · Cited by 30
Comparing MCSA with vibration analysis in order to detect bearing faults — A case study
Corne, B., Vervisch, B., Debruyne, C., Knockaert, J., & Desmet, J. J. M. (2015) · IEEE International Electric Machines & Drives Conference (IEMDC) · doi:10.1109/iemdc.2015.7409240 · Cited by 29
Zhou, X., Zhou, H., Wen, G., Huang, X., Lei, Z., Zhang, Z., & Chen, X. (2021) · Measurement · doi:10.1016/j.measurement.2021.110633 · Cited by 29
Nazari, S., Shokoohi, S., & Moshtagh, J. (2023) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/tim.2023.3280506 · Cited by 28
“Simulation and experimental results demonstrate the superiority of the proposed method over conventional methods in [17], [19], [20], and [21].”
BackgroundMethodResultInfluentialZhang, B., Li, H., Kong, W., Fu, M., & Ma, J. (2024) · Sensors · doi:10.3390/s24113373 · Cited by 27
“Statistics show that about 41% of common motor faults are caused by bearing failures [1].”
BackgroundNguyen, T.-K., Ahmad, Z., & Kim, J.-M. (2022) · Sensors · doi:10.3390/s22103687 · Cited by 27
“Following this approach, the studies in [11,26,40,41] investigated the faults with respect to fault-related frequencies, which indicates that the comprehension of the system and fault nature is necessary.”
Background
Metadata
- Authors
- Leite, V. C. M. N., Borges da Silva, J. G., Veloso, G. F. C., Borges da Silva, L. E., Lambert-Torres, G., Bonaldi, E. L., & de Lacerda de Oliveira, L. E.
- Affiliations
- Department of Aerospace Science and Technology (BR)
- Universidade Federal de Itajubá (BR)
- Venue
- IEEE Transactions on Industrial Electronics
- Published
- 2015-03
- Volume
- 62
- Issue
- 3
- Pages
- 1855-1865
- ISSN
- 0278-0046 (ISSN-L)
- 1557-9948
- OpenAlex
- W1993880634
- Cited by
- 274
- References
- 43
- Citations by year
- 2026: 5 · 2025: 15 · 2024: 21 · 2023: 21 · 2022: 23 · 2021: 32 · 2020: 29 · 2019: 33 · 2018: 33 · 2017: 26 · 2016: 21 · 2015: 14
- FWCI
- 23.05
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- IEEE Transactions on Industrial Electronics (publishedVersion)
- Topics
- Physical Sciences › Engineering › Control and Systems Engineering › Machine Fault Diagnosis Techniques
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Electric Motor Design and Analysis
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Electrical Fault Detection and Protection
- Keywords
- bearing fault detection, induction motor, stator current, spectral kurtosis, envelope analysis, fast kurtogram, condition monitoring, fault location
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.