High-Efficiency Module Design of Solid-State Transformers for Railway Vehicles
The DOI matches its Crossref record; 28 of the 28 references it cites were found in a registry or an index.
Abstract
The solid-state transformer (SST) can be a promising solution to replace the conventional 50- or 60-Hz main transformer (MTr) for railway vehicles. Unlike the existing SST technologies for stationary power applications, the SST applied to railway vehicles requires severe constraint of installation space and intensive management of heat dissipation. To optimally design the SST module applied to the railway vehicles, which is one of the major components in the whole SST system, the optimal magnetic component designs for high-efficiency and thermal stable operations in the confined installation space are proposed in this article. In order to meet the SST system requirements for ac 25-kV-to-dc 1.5-kV power conversion, an overall SST topology and its control schemes are established. Based on the proposed SST topology, considering the operating drive profile of the urban railway vehicles, the operating sequence of the proposed SST is introduced and verified by simulation. By virtue of the proposed magnetic component design, the optimal number of turns for the inductor and transformer in dual-active-bridge converters can be appropriately determined for 50-kV high-voltage insulation and high-efficiency operation when the installation space for the magnetic components is given. For targeting the 3.0-MW maximum power transfer capability of the proposed SST system, the 300-kW SST modules, operating at 500 Hz and 10 kHz for ac/dc converters and dc/dc converters, respectively, were fabricated and verified by experiment. By two experimental SST module sets, the static performance of the power converters in the SST module and the dynamic operating sequence has been successfully implemented. For the 300-kW full-load operation, 99.7% of power transfer efficiency for the proposed magnetic components and 97.2% of total power efficiency were obtained. As a result, the measured temperature characteristics for the proposed SST module, including the magnetic components, were managed below 125 °C under a severe experimental environment.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Citations
Cites
DC Microgrids—Part II: A Review of Power Architectures, Applications, and Standardization Issues
Dragicevic, T., Lu, X., Vasquez, J. C., & Guerrero, J. M. (2016) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2015.2464277 · Cited by 1,451 · cited 1×
“, dc microgrid [11]–[13], wind turbine [14], and future”
BackgroundMore Electric Aircraft: Review, Challenges, and Opportunities for Commercial Transport Aircraft
Sarlioglu, B., & Morris, C. T. (2015) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2015.2426499 · Cited by 1,261
Extreme Fast Charging of Electric Vehicles: A Technology Overview
Tu, H., Feng, H., Srdic, S., & Lukic, S. (2019) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2019.2958709 · Cited by 898
A New AC/AC Multilevel Converter Family
Glinka, M., & Marquardt, R. (2005) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2005.843973 · Cited by 772 · cited 3×
“previous studies [5]–[10], the efficiency and weight results of”
BackgroundMethodResultSteinmetz, C. P. (1984) · Proceedings of the IEEE · doi:10.1109/proc.1984.12842 · Cited by 656
Applicability of solid-state transformers in today's and future distribution grids
Huber, J. E., & Kolar, J. W. (2019) · IEEE Transactions on Smart Grid · doi:10.1109/tsg.2017.2738610 · Cited by 506 · cited 7×
“increased due to the inherent characteristics of the switching devices in these HV applications [1]–[10], the magnetic”
BackgroundInfluentialPower Electronic Traction Transformer—Medium Voltage Prototype
Zhao, C., Dujic, D., Mester, A., Steinke, J. K., Weiss, M., Lewdeni-Schmid, S., Chaudhuri, T., & Stefanutti, P. (2014) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2013.2278960 · Cited by 478 · cited 7×
“increased due to the inherent characteristics of the switching devices in these HV applications [1]–[10], the magnetic”
BackgroundMethodResultInfluentialFan, H., & Li, H. (2011) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2011.2160652 · Cited by 401 · cited 1×
“Then, the load power for the DAB converters having an inductor in the secondary side can be calculated under the given switching frequency fs and inductance Ld , as follows [18], [19]:”
MethodMedium frequency topology in railway applications
Steiner, M., & Reinold, H. (2007) · 2007 European Conference on Power Electronics and Applications · doi:10.1109/epe.2007.4417570 · Cited by 249 · cited 2×
“In 2007, a 3.0-MW SST prototype having seven modules was developed by Bombardier [7], [8].”
MethodInfluentialPower Electronic Transformer-Based Railway Traction Systems: Challenges and Opportunities
Feng, J., Chu, W. Q., Zhang, Z., & Zhu, Z. Q. (2017) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2017.2685464 · Cited by 229
Research works printed but not linked: 1
- Ferrite Core Datasheet
Cited by
High Efficiency Integrated Transformer Design in DAB Converters for Solid-State Transformers
Lee, E. S., Park, J. H., Kim, M. Y., & Lee, J. S. (2022) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2022.3168561 · Cited by 63
Self-citationOptimal IPT Core Design for Wireless Electric Vehicles by Reinforcement Learning
Jeong, M. S., Jang, J. H., & Lee, E. S. (2023) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2023.3297740 · Cited by 23
“The DAB converter is commonly employed to transfer power by adjusting the phase difference ( φ d ) between the primary and secondary sides [20].”
MethodSelf-citationMedium-Voltage Solid-State Transformer Design for Large-Scale H 2 Electrolyzers
Li, Z., Mirzadarani, R., Niasar, M. G., Itraj, M., Lieshout, L. V., Bauer, P., & Qin, Z. (2024) · IEEE Open Journal of Power Electronics · doi:10.1109/ojpel.2024.3414151 · Cited by 26
Optimization Design of High-Frequency Matrix Transformer for Solid-State Transformer
Wan, Z., Li, Y., Wang, H., & Li, X. (2024) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2024.3424509 · Cited by 16
“By finely considering the number of turns in the winding, an innovative method for designing inductors and HFTs is proposed in [23].”
MethodLee, E. S., Song, S.-H., Park, J. H., & Kim, M. R. (2022) · IET Power Electronics · doi:10.1049/pel2.12418 · Cited by 14
Self-citation
Metadata
- Authors
- Lee, E. S., Park, J. H., Kim, M. Y., & Lee, J. S.
- Affiliations
- Hanyang University (KR)
- Korea Railroad Research Institute (KR)
- Dankook University (KR)
- Venue
- IEEE Transactions on Transportation Electrification
- Published
- 2022-03
- Volume
- 8
- Issue
- 1
- Pages
- 98-120
- ISSN
- 2332-7782 (ISSN-L)
- 2372-2088
- OpenAlex
- W3195409422
- Cited by
- 36
- References
- 28
- Citations by year
- 2026: 8 · 2025: 6 · 2024: 8 · 2023: 5 · 2022: 8
- FWCI
- 1.62
- Type
- journal article
- Language
- en
- Open access
- closed
- Licence
- Locations
- IEEE Transactions on Transportation Electrification (publishedVersion)
- Funders
- Ministry of Land, Infrastructure and Transport (MOLIT) of the Korean Government through the Railroad Technology Development Program (21RSCD-C163337-01)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advanced DC-DC Converters
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Wireless Power Transfer Systems
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Multilevel Inverters and Converters
- Keywords
- solid-state transformer, railway rolling stock, magnetic component design, dual active bridge converter, high-voltage insulation, power conversion efficiency, thermal management, AC-DC converter, DC-DC converter, operating sequence, power transfer capability
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: High-Efficiency Module Design of Solid-State Transformers for Railway Vehicles. https://app.cochat.ai/papers/10.1109/tte.2021.3101733
- The paper
- Lee, E. S., Park, J. H., Kim, M. Y., & Lee, J. S. (2022). High-Efficiency Module Design of Solid-State Transformers for Railway Vehicles. IEEE Transactions on Transportation Electrification. https://doi.org/10.1109/tte.2021.3101733
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.