Tensile Mechanical Properties of Three-Dimensional Type I Collagen Extracellular Matrices With Varied Microstructure
The DOI matches its Crossref record; 41 of the 41 references it cites were found in a registry or an index.
Abstract
The importance and priority of specific micro-structural and mechanical design parameters must be established to effectively engineer scaffolds (biomaterials) that mimic the extracellular matrix (ECM) environment of cells and have clinical applications as tissue substitutes. In this study, three-dimensional (3-D) matrices were prepared from type I collagen, the predominant compositional and structural component of connective tissue ECMs, and structural-mechanical relationships were studied. Polymerization conditions, including collagen concentration (0.3–3 mg/mL) and pH (6–9), were varied to obtain matrices of collagen fibrils with different microstructures. Confocal reflection microscopy was used to assess specific micro-structural features (e.g., diameter and length) and organization of component fibrils in 3-D. Microstructural analyses revealed that changes in collagen concentration affected fibril density while maintaining a relatively constant fibril diameter. On the other hand, both fibril length and diameter were affected by the pH of the polymerization reaction. Mechanically, all matrices exhibited a similar stress-strain curve with identifiable “toe,” “linear,” and “failure” regions. However, the linear modulus and failure stress increased with collagen concentration and were correlated with an increase in fibril density. Additionally, both the linear modulus and failure stress showed an increase with pH, which was related to an increased fibril length and a decreased fibril diameter. The tensile mechanical properties of the collagen matrices also showed strain rate dependence. Such fundamental information regarding the 3-D microstructural-mechanical properties of the ECM and its component molecules are important to our overall understanding of cell-ECM interactions (e.g., mechanotransduction) and the development of novel strategies for tissue repair and replacement.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Citations
Cites
Biomechanics. Mechanical Properties of Living Tissues
Fung, Y. C., & Skalak, R. (1982) · Journal of Applied Mechanics · doi:10.1115/1.3162171 · Cited by 6,025
Materials Science and Engineering: An Introduction
Callister, W. D. (1985) · Cited by 5,351
Design of an artificial skin. I. Basic design principles
Yannas, I. V., & Burke, J. F. (1980) · Journal of Biomedical Materials Research · doi:10.1002/jbm.820140108 · Cited by 1,044
Design of an artificial skin. I. Basic design principles
Yannas, I. V., & Burke, J. F. (1980) · Journal of Biomedical Materials Research · doi:10.1002/jbm.820140314 · Cited by 889
[2] Preparation and characterization of the different types of collagen
Miller, E. J., & Kent Rhodes, R. (1982) · Methods in Enzymology · doi:10.1016/0076-6879(82)82059-4 · Cited by 752
Collagen; ultrastructure and its relation to mechanical properties as a function of ageing
Diamant, J., Keller, A., Baer, E., Litt, M., & Arridge, R. G. C. (1972) · Proceedings of the Royal Society of London. Series B. Biological Sciences · doi:10.1098/rspb.1972.0019 · Cited by 553
Isometric contraction by fibroblasts and endothelial cells in tissue culture: a quantitative study
Kolodney, M., & Wysolmerski, R. (1992) · The Journal of cell biology · doi:10.1083/jcb.117.1.73 · Cited by 447
Wood, G. C., & Keech, M. K. (1960) · Biochemical Journal · doi:10.1042/bj0750588 · Cited by 443
Regulation of extracellular matrix gene expression by mechanical stress
Chiquet, M. (1999) · Matrix Biology · doi:10.1016/s0945-053x(99)00039-6 · Cited by 427
Pins, G. D., Christiansen, D. L., Patel, R., & Silver, F. H. (1997) · Biophysical Journal · doi:10.1016/s0006-3495(97)78247-x · Cited by 390
Research works printed but not linked: 1
- Bateman, J. F., Lamande, S. R., and Ramshaw, J. A. M., 1996, “Collagen Superfamily,” Extracellular Matrix Vol. 2., Molecular Components and Interaction, ed., W. D. Comper, Harwood Academic Publishers, The Netherlands, pp. 22–67.
Cited by
Items 201–300 of 694
Kotlarchyk, M. A., Botvinick, E. L., & Putnam, A. J. (2010) · Journal of Physics Condensed Matter · doi:10.1088/0953-8984/22/19/194121 · Cited by 54
Szulczewski, J. M., Inman, D. R., Proestaki, M., Notbohm, J., Burkel, B. M., & Ponik, S. M. (2021) · Acta Biomaterialia · doi:10.1016/j.actbio.2021.04.053 · Cited by 54
Erişken, C., Kalyon, D. M., Zhou, J. P., Kim, S. G., & Mao, J. J. (2015) · Journal of Endodontics · doi:10.1016/j.joen.2015.07.005 · Cited by 53
A DIGITAL VOLUME CORRELATION TECHNIQUE FOR 3-D DEFORMATION MEASUREMENTS OF SOFT GELS
Huang, J., Pan, X., Li, S., Peng, X., Xiong, C., & Fang, J. (2011) · International Journal of Applied Mechanics · doi:10.1142/s1758825111001019 · Cited by 53
Won, J., Cho, Y., Lee, D., Jeon, B. Y., Ju, J., Chung, S. H., & Pak, J. H. (2019) · PLoS Pathogens · doi:10.1371/journal.ppat.1007818 · Cited by 53
Controlling collagen fiber microstructure in three-dimensional hydrogels using ultrasound
Garvin, K. A., VanderBurgh, J. A., Hocking, D. C., & Dalecki, D. (2013) · The Journal of the Acoustical Society of America · doi:10.1121/1.4812868 · Cited by 52
“Interestingly, the mechanical stiffness of collagen hydrogels is dependent upon collagen fiber microstructure, where thinner fibers result in stiffer gels (Roeder et al., 2002; Raub et al., 2007; Yang et al., 2009).”
BackgroundCollagen content and extracellular matrix cause cytoskeletal remodelling in pancreatic fibroblasts
Stylianou, A., Gkretsi, V., Louca, M., Zacharia, L. C., & Stylianopoulos, T. (2019) · Journal of The Royal Society Interface · doi:10.1098/rsif.2019.0226 · Cited by 52
Lake, S. P., Hald, E. S., & Barocas, V. H. (2011) · Journal of Biomedical Materials Research Part A · doi:10.1002/jbm.a.33183 · Cited by 52
Mercado‐Shekhar, K. P., Helguera, M., Hocking, D. C., & Dalecki, D. (2014) · Tissue Engineering Part C Methods · doi:10.1089/ten.tec.2014.0527 · Cited by 51
ACVR1R206HFOP mutation alters mechanosensing and tissue stiffness during heterotopic ossification
Haupt, J., Stanley, A. K., McLeod, C. M., Cosgrove, B. D., Culbert, A. L., Wang, L., Mourkioti, F., Mauck, R. L., & Shore, E. M. (2018) · Molecular Biology of the Cell · doi:10.1091/mbc.e18-05-0311 · Cited by 51
Differences in Collagen Fiber Diameter and Waviness between Healthy and Aneurysmal Abdominal Aortas
Niestrawska, J. A., Pukaluk, A., Babu, A. R., & Holzapfel, G. A. (2022) · Microscopy and Microanalysis · doi:10.1017/s1431927622000629 · Cited by 51
“However, the usual manual approach to measuring the diameter is supported by image analysis software (Pickering et al., 1996; Brightman et al., 2000; Roeder et al., 2002; Mencucci et al., 2010; Changoor et al., 2011; Chen et al., 2011, 2013).”
BackgroundMethodDigital microfluidics for spheroid-based invasion assays
Bender, B. F., Aijian, A. P., & Garrell, R. L. (2016) · Lab on a Chip · doi:10.1039/c5lc01569c · Cited by 49
Acellular and cellular high-density, collagen-fibril constructs with suprafibrillar organization
Blum, K. M., Novak, T., Watkins, L., Neu, C. P., Wallace, J. M., Bart, Z. R., & Voytik‐Harbin, S. L. (2016) · Biomaterials Science · doi:10.1039/c5bm00443h · Cited by 49
Self-citationFactors affecting the mechanical behavior of collagen hydrogels for skin tissue engineering
Pensalfini, M., Ehret, A. E., Stuedeli, S., Marino, D., Kaech, A., Reichmann, E., & Mazza, E. (2016) · Journal of the mechanical behavior of biomedical materials/Journal of mechanical behavior of biomedical materials · doi:10.1016/j.jmbbm.2016.12.004 · Cited by 49
Riedel, S., Hietschold, P., Krömmelbein, C., Kunschmann, T., Konieczny, R., Knolle, W., Mierke, C. T., Zink, M., & Mayr, S. G. (2019) · Materials & Design · doi:10.1016/j.matdes.2019.107606 · Cited by 48
Electroconductive scaffolds based on gelatin and PEDOT:PSS for cardiac regeneration
Furlani, F., Campodoni, E., Sangiorgi, N., Montesi, M., Sanson, A., Sandri, M., & Panseri, S. (2022) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2022.10.122 · Cited by 48
Fibronectin matrix polymerization increases tensile strength of model tissue
Gildner, C. D., Lerner, A. L., & Hocking, D. C. (2004) · American Journal of Physiology-Heart and Circulatory Physiology · doi:10.1152/ajpheart.00859.2003 · Cited by 48
“The increased failure strain observed in our system could occur through several mechanisms including changes in the extent of intrafibrillar cross-links or hydrophobic interactions or alterations in the organizational structure of the collagen bundles (29).”
BackgroundResultFeng, C.-H., Cheng, Y., & Chao, P. G. (2012) · Acta Biomaterialia · doi:10.1016/j.actbio.2012.11.024 · Cited by 47
“for excitation and imaging with a bandpass filter of 490–500 nm [39].”
MethodShemesh, M., & Zilberman, M. (2013) · Acta Biomaterialia · doi:10.1016/j.actbio.2013.11.025 · Cited by 47
“Similar trends of collagen fibers and scaffolds have been reported previously [36,37].”
ResultThe Self-Assembling Peptide P 11 -4 Prevents Collagen Proteolysis in Dentin
de Sousa, J. P., de Carvalho, R. G., Martins, L. F. B., Torquato, R. J. S., Mugnol, K. C. U., Nascimento, F. D., Tersariol, I. L. S., & Puppin‐Rontani, R. M. (2019) · Journal of Dental Research · doi:10.1177/0022034518817351 · Cited by 47
“Numerous literature reports have correlated increased collagen polymerization with increasing hydrogel linear tensile modulus (Roeder et al. 2002; Raub et al. 2007).”
BackgroundMuangsanit, P., Day, A. G. E., Dimiou, S., Ataç, A. F., Kayal, C., Park, H., Nazhat, S. N., & Phillips, J. B. (2020) · Journal of Neural Engineering · doi:10.1088/1741-2552/abaa9c · Cited by 47
Engineering Biomaterials and Approaches for Mechanical Stretching of Cells in Three Dimensions
Zhang, W., Huang, G., & Xu, F. (2020) · Frontiers in Bioengineering and Biotechnology · doi:10.3389/fbioe.2020.589590 · Cited by 47
Qiu, Y., Lei, J. L., Koob, T. J., & Temenoff, J. S. (2014) · Journal of Tissue Engineering and Regenerative Medicine · doi:10.1002/term.1880 · Cited by 46
“, 2007), the maximum tensile modulus of such gels remains well below 1MPa (Roeder et al., 2002), which is inferior to that of tendon/ligament tissues (~200–800MPa) (Staubli et al.”
BackgroundGkretsi, V., Stylianou, A., Louca, M., & Stylianopoulos, T. (2017) · Oncotarget · doi:10.18632/oncotarget.16062 · Cited by 46
“To increase the stiffness of 3D collagen gels, we increased their concentration [34, 35].”
BackgroundResultMechanical response of collagen networks to nonuniform microscale loads
Burkel, B. M., & Notbohm, J. (2017) · Soft Matter · doi:10.1039/c7sm00561j · Cited by 46
Dual-Spun Shape Memory Elastomeric Composites
Robertson, J. M., Nejad, H. B., & Mather, P. T. (2015) · ACS Macro Letters · doi:10.1021/acsmacrolett.5b00106 · Cited by 45
Compartmentalized Spherical Collagen Microparticles for Anisotropic Cell Culture Microenvironments
Yoshida, S., Takinoue, M., & Onoe, H. (2017) · Advanced Healthcare Materials · doi:10.1002/adhm.201601463 · Cited by 45
Biomimetic Collagen Tissues: Collagenous Tissue Engineering and Other Applications
Sander, E. A., & Barocas, V. H. (2008) · Springer eBooks · doi:10.1007/978-0-387-73906-9_17 · Cited by 45
Layton, B. E., & Sastry, A. M. (2004) · Journal of Biomechanical Engineering · doi:10.1115/1.1824118 · Cited by 45
Freytes, D. O., Rundell, A. E., Geest, J. V., Vorp, D. A., Webster, T. J., & Badylak, S. F. (2005) · Biomaterials · doi:10.1016/j.biomaterials.2005.01.070 · Cited by 45
Surface-textured PEG-based hydrogels with adjustable elasticity: Synthesis and characterization
Pfister, P. M., Wendlandt, M., Neuenschwander, P., & Suter, U. W. (2006) · Biomaterials · doi:10.1016/j.biomaterials.2006.09.016 · Cited by 45
“Despite the enormous range of elastic moduli usually found in human tissue ranging from a few kPa to a few GPa [36–41], most investigations of the influence of the substrate stiffness on cell behavior focused only on the”
BackgroundDesign and sustainability of polypeptide material systems
Yorke, S. K., Yang, Z., Wiita, E. G., Kamada, A., Knowles, T. P. J., & Buehler, M. J. (2025) · Nature Reviews Materials · doi:10.1038/s41578-025-00793-3 · Cited by 44
“These properties mean that collagen-based materials can have a higher resilience than other polypeptide materials, such as amyloid structures, and have been engineered as films 144,145 , scaffolds 146,147 , sponges 148,149 , hydrogels 150–152 and composites.”
Confined compression of collagen hydrogels
Busby, G. A., Grant, M. H., Mackay, S. P., & Riches, P. E. (2012) · Journal of Biomechanics · doi:10.1016/j.jbiomech.2012.11.048 · Cited by 44
“The stiffness of collagen hydrogels in tension increases relative to collagen content (Krishnan et al., 2004; Roeder et al., 2002), and consequently a larger fibril density should also translate to increased compressive matrix stiffness.”
BackgroundMicrostructure and Mechanics of Collagen-Fibrin Matrices Polymerized Using Ancrod Snake Venom Enzyme
Rowe, S. L., & Stegemann, J. P. (2009) · Journal of Biomechanical Engineering · doi:10.1115/1.3128673 · Cited by 44
Reyna, W. E., Pichika, R., Ludvig, D., & Perreault, E. J. (2020) · Journal of Biomechanics · doi:10.1016/j.jbiomech.2020.109961 · Cited by 42
“Modeling has also been used to predict the mechanical properties of ECM from knowledge of collagen fiber mechanics and the structure of their arrangement in ECM (Bleiler et al., 2019; Roeder et al., 2002), but these predictions have not been validated by direct measurements.”
MethodModeling Extracellular Matrix Reorganization in 3D Environments
Harjanto, D., & Zaman, M. H. (2013) · PLoS ONE · doi:10.1371/journal.pone.0052509 · Cited by 44
“corresponding adjustment in tensile properties [10].”
Liu, A. S., Wang, H., Copeland, C. R., Chen, C. S., Shenoy, V. B., & Reich, D. H. (2016) · Scientific Reports · doi:10.1038/srep33919 · Cited by 43
Fernández-Cervantes, I., Rodríguez‐Fuentes, N., León-Deniz, L. V., Alcántara-Quintana, L. E., Cervantes‐Uc, J. M., Kao, W. A. H., Cerón-Espinosa, J. D., Cauich‐Rodríguez, J. V., & Castaño, V. M. (2020) · Materials Science and Engineering C · doi:10.1016/j.msec.2020.110748 · Cited by 43
Lühr, I., Friedl, A., Overath, T., Tholey, A., Kunze, T., Hilpert, F., Sebens, S., Arnold, N., Rösel, F., Oberg, H., et al. (2012) · Cancer Letters · doi:10.1016/j.canlet.2012.06.014 · Cited by 43
“demonstrated that elevating collagen concentration leads to increased collagen matrix stiffness [29].”
Whittington, C. F., Yöder, M. C., & Voytik‐Harbin, S. L. (2013) · Macromolecular Bioscience · doi:10.1002/mabi.201300128 · Cited by 43
“, fibril density, fibril diameter, interstitial fluid viscosity, and matrix stiffness) of polymerizable collagen-fibril matrices.[33, 34, 36, 37] In fact, an increase in collagen concentration has been routinely used to document how matrix stiffness, which occurs as a result of increased fibril density, effectively mo…”
BackgroundSelf-citationTissue constructs: platforms for basic research and drug discovery
Elson, E. L., & Genin, G. M. (2015) · Interface Focus · doi:10.1098/rsfs.2015.0095 · Cited by 43
Mechanical contribution of vascular smooth muscle cells in the tunica media of artery
Mozafari, H., Zhou, C., & Gu, L. (2019) · Nanotechnology Reviews · doi:10.1515/ntrev-2019-0005 · Cited by 42
Nagel, T., & Kelly, D. J. (2011) · Biomechanics and Modeling in Mechanobiology · doi:10.1007/s10237-011-0313-3 · Cited by 41
“…(strain-dependent) tensile moduli on the order of 10’s of kPa (which is on the order of experimentally reported values for 3 mg/ml collagen gels (Roeder et al. 2002), the same concentration used in Thomopoulos et al. (2005) and compressive moduli in the range of≈0.3 kPa creating a material…”
InfluentialMultiscale Modeling of the Skeletal System
Viceconti, M. (2011) · Cambridge University Press eBooks · doi:10.1017/cbo9781139049627 · Cited by 41
Tomei, A. A., Boschetti, F., Gervaso, F., & Swartz, M. A. (2008) · Biotechnology and Bioengineering · doi:10.1002/bit.22236 · Cited by 41
“, fibroblasts and smooth muscle cells can contract a matrix to a fraction of its original size) and because such reconstituted collagen and fibrin cannot maintain any residual stress when compressed or stretched (Pedersen and Swartz, 2005; Roeder et al., 2002).”
BackgroundYoung's modulus of collagen at slow displacement rates
Lopez-Garcia, M. D. C., Beebe, D. J., & Crone, W. C. (2010) · Bio-Medical Materials and Engineering · doi:10.3233/bme-2010-0649 · Cited by 41
“The mathematical model obtained was then used to extrapolate the Young’s modulus data to the desired strain rates relevant to cell motion.”
Collagen gel fibrillar density dictates the extent of mineralization in vitro
Marelli, B., Ghezzi, C. E., Barralet, J. E., & Nazhat, S. N. (2011) · Soft Matter · doi:10.1039/c1sm06027a · Cited by 40
Analysis of Orientations of Collagen Fibers by Novel Fiber-Tracking Software
Wu, J., Rajwa, B. P., Filmer, D. L., Hoffmann, C. M., Yuan, B., Chiang, C.-S., Sturgis, J., & Robinson, J. P. (2003) · Microscopy and Microanalysis · doi:10.1017/s1431927603030277 · Cited by 40
“This has generated a considerable interest in determining collagen fiber length, orientation, and diameter in nonprocessed and nonfixed collagen matrices ~ Brightman et al., 2000; Ottani et al., 2001; Voytik-Harbin et al., 2001; Roeder et al., 2002 !”
BackgroundSelf-citationTough Supersoft Sponge Fibers with Tunable Stiffness from a DNA Self‐Assembly Technique
Lee, C. K., Shin, S. R., Mun, J. Y., Han, S., So, I., Jeon, J., Kang, T. M., Kim, S. I., Whitten, P. G., Wallace, G. G., et al. (2009) · Angewandte Chemie International Edition · doi:10.1002/anie.200804788 · Cited by 40
Modulation of Corneal Fibroblast Contractility within Fibrillar Collagen Matrices
Vishwanath, M., Ma, L., Otey, C. A., Jester, J. V., & Petroll, W. M. (2003) · Investigative Ophthalmology & Visual Science · doi:10.1167/iovs.03-0513 · Cited by 40
“3 was used.(54) To generate a map of ECM deformation, the dis-”
MethodSui, J., Pragnère, S., & Kurniawan, N. A. (2025) · Biomaterials Science · doi:10.1039/d5bm00210a · Cited by 39
Biopolymer-based hydrogels as injectable materials for tissue repair scaffolds
Fiejdasz, S., Szczubiałka, K., Lewandowska-Łańcucka, J., Osyczka, A. M., & Nowakowska, M. (2013) · Biomedical Materials · doi:10.1088/1748-6041/8/3/035013 · Cited by 39
“As already mentioned, collagen has a lot of remarkable advantages as a material for biomedical applications, however, it shows poor mechanical properties [39, 40].”
BackgroundKašaj, A., Levin, L., Stratul, Ş., Götz, H., Schlee, M., Rütters, C. B., Konerding, M. A., Ackermann, M., Willershausen, B., & Pabst, A. M. (2015) · Clinical Oral Investigations · doi:10.1007/s00784-015-1614-1 · Cited by 39
Hybrid cellular Potts and bead-spring modeling of cells in fibrous extracellular matrix
Tsingos, E., Bakker, B. H., Keijzer, K. A. E., Hupkes, H. J., & Merks, R. M. H. (2023) · Biophysical Journal · doi:10.1016/j.bpj.2023.05.013 · Cited by 38
RhoA is down-regulated at cell–cell contacts via p190RhoGAP-B in response to tensional homeostasis
Ponik, S. M., Trier, S. M., Wozniak, M. A., Eliceiri, K. W., & Keely, P. J. (2013) · Molecular Biology of the Cell · doi:10.1091/mbc.e12-05-0386 · Cited by 38
“The increase in collagen density has been associated with an increase in extracellular matrix (ECM) stiffness (Roeder et al., 2002; Gehler et al., 2009).”
BackgroundElsaadany, M., Winters, K., Adams, S. E., Stasuk, A., Ayan, H., & Yildirim-Ayan, E. D. (2017) · Scientific Reports · doi:10.1038/s41598-017-13240-3 · Cited by 38
Bhuiyan, D. B., Jablonsky, M. J., Kolesov, I., Middleton, J., Wick, T. M., & Tannenbaum, R. (2014) · Acta Biomaterialia · doi:10.1016/j.actbio.2014.11.044 · Cited by 37
“62 MPa, which is close to the range of human cancellous bone of 7–20 MPa [48–50] and 300 times higher than the strength of pure collagen (10–12 kPa) [51], the latter having been tried clinically to enhance bone healing.”
BackgroundTamadon, A., Baghestani, A., & Bajgholi, M. E. (2020) · Technologies · doi:10.3390/technologies8020034 · Cited by 37
“This behaviour is explained as the toe region at the beginning of the tensile test [45,46], where the mechanical loading is less than 2% nonlinear strain for the stress–strain curve [47].”
BackgroundImpact of crosslink heterogeneity on extracellular matrix mechanics and remodeling
Mak, M. (2020) · Computational and Structural Biotechnology Journal · doi:10.1016/j.csbj.2020.11.038 · Cited by 37
“In bulk rheological measurements, hysteresis and failure can be achieved under large strain amplitudes [3,4].”
BackgroundEvans, M. C., & Barocas, V. H. (2009) · Journal of Biomechanical Engineering · doi:10.1115/1.4000064 · Cited by 37
Nanomechanical Analysis of Extracellular Matrix and Cells in Multicellular Spheroids
Vyas, V., Solomon, M. A., D’Souza, G. G. M., & Huey, B. D. (2019) · Cellular and Molecular Bioengineering · doi:10.1007/s12195-019-00577-0 · Cited by 37
Three-dimensional simulation of anisotropic cell-driven collagen gel compaction
Ohsumi, T. K., Flaherty, J. E., Evans, M. C., & Barocas, V. H. (2007) · Biomechanics and Modeling in Mechanobiology · doi:10.1007/s10237-007-0075-0 · Cited by 36
“Collagen gels made under different conditions exhibit different structural and mechanical properties (Roeder et al. 2002), so our model must be viewed as a representative but not exact with respect to collagen gel properties.”
BackgroundMeghezi, S., Couët, F., Chevallier, P., & Mantovani, D. (2012) · International Journal of Biomaterials · doi:10.1155/2012/319290 · Cited by 36
Modeling Contact Guidance and Invasion by Cancer Cells
Sander, L. M. (2014) · Cancer Research · doi:10.1158/0008-5472.can-13-3294 · Cited by 36
Flow-manipulated, crosslinked collagen gels for use as corneal equivalents
Duncan, T., Tanaka, Y., Shi, D., Kubota, A., Quantock, A. J., & Nishida, K. (2010) · Biomaterials · doi:10.1016/j.biomaterials.2010.08.042 · Cited by 36
Dialysis as a method of obtaining neutral collagen gels
Skopińska-Wiśniewska, J., Olszewski, K., Bajek, A., Rynkiewicz, A., & Sionkowska, A. (2014) · Materials Science and Engineering C · doi:10.1016/j.msec.2014.03.029 · Cited by 36
Quantitative assessment of cell contractility using polarized light microscopy
Wang, W., Miller, J. P., Pannullo, S. C., Reinhart‐King, C. A., & Bordeleau, F. (2018) · Journal of Biophotonics · doi:10.1002/jbio.201800008 · Cited by 36
Chan, B. P., Li, C. H., Au-yeung, K., Sze, K. Y., & Ngan, A. H. W. (2008) · Annals of Biomedical Engineering · doi:10.1007/s10439-008-9507-y · Cited by 36
Prominent Vascularization Capacity of Mesenchymal Stem Cells in Collagen–Gold Nanocomposites
Hsieh, S., Chen, H.-J., Hsu, S., Yang, Y., Tang, C., Chu, M.-Y., Lin, P., Fu, R., Kung, M., Chen, Y., et al. (2016) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.6b09330 · Cited by 35
Hu, L.-Y., Mileti, C. J., Loomis, T., Brashear, S. E., Ahmad, S., Chellakudam, R. R., Wohlgemuth, R. P., Gionet‐Gonzales, M., Leach, J. K., & Smith, L. (2021) · American Journal of Physiology-Cell Physiology · doi:10.1152/ajpcell.00065.2021 · Cited by 35
A Novel Chemotaxis Assay in 3-D Collagen Gels by Time-Lapse Microscopy
Vasaturo, A., Caserta, S., Russo, I., Preziosi, V., Ciacci, C., & Guido, S. (2012) · PLoS ONE · doi:10.1371/journal.pone.0052251 · Cited by 35
“Even though in vitro 3D collagen-based matrices lack the structural complexity and cross-links between molecules present in connective tissues [51], they reproduce the essential features of the structural characteristics of the network-like extracellular matrix and remain the most commonly used substrates to replace n…”
BackgroundBhuiyan, D. B., Middleton, J. C., Tannenbaum, R., & Wick, T. M. (2016) · Journal of Biomaterials Science Polymer Edition · doi:10.1080/09205063.2016.1184121 · Cited by 35
“4 MPa, which is very close to the range of human cancellous bone 7–20 MPa [26–28] and more than 300 times higher than that of pure collagen (10–12 kPa).[35] The bending modulus of nHAP-PLGA-collagen (0.”
BackgroundLee, D. W., Ho, C.-H., & Grinnell, F. (2003) · Experimental Cell Research · doi:10.1016/s0014-4827(03)00254-4 · Cited by 35
Collagen-based hydrogel sol-gel phase transition mechanism and their applications
Yang, X., Ahmad, K., Yang, T., Fan, Y., Zhao, F., Jiang, S., Chen, P., & Hou, H. (2025) · Advances in Colloid and Interface Science · doi:10.1016/j.cis.2025.103456 · Cited by 34
Moo, E. K., Ebrahimi, M., Sibole, S. C., Tanska, P., & Korhonen, R. K. (2022) · Acta Biomaterialia · doi:10.1016/j.actbio.2022.09.002 · Cited by 34
Mierke, C. T. (2024) · Biomolecules · doi:10.3390/biom14020184 · Cited by 34
Torres, F. G., Troncoso, O. P., & Montes, M. R. (2013) · Journal of Thermal Analysis and Calorimetry · doi:10.1007/s10973-012-2915-0 · Cited by 34
Multiscale Strain Analysis of Tissue Equivalents Using a Custom-Designed Biaxial Testing Device
Bell, B. J., Nauman, E. A., & Voytik‐Harbin, S. L. (2012) · Biophysical Journal · doi:10.1016/j.bpj.2012.02.007 · Cited by 33
“Examples of such porous structures that are suited to transmit forces to the matrix include polyethylene mesh, porous polyethylene blocks, and hook-and-loop fasteners (14,35,36).”
BackgroundSelf-citationCapturing relevant extracellular matrices for investigating cell migration
Keely, P. J., & Nain, A. S. (2015) · F1000Research · doi:10.12688/f1000research.6623.1 · Cited by 33
Microstructural Characteristics of Extracellular Matrix Produced by Stromal Fibroblasts
Crabb, R. A. B., Chau, E. P., Decoteau, D. M., & Hubel, A. (2006) · Annals of Biomedical Engineering · doi:10.1007/s10439-006-9181-x · Cited by 33
Rennert, R. C., Rustad, K. C., Levi, K., Harwood, M. D., Sorkin, M., Wong, V., Al‐Ahmad, A., Zei, P. C., Hsia, H. H., Beygui, R. E., et al. (2014) · Acta Biomaterialia · doi:10.1016/j.actbio.2014.01.008 · Cited by 33
Keyes, J. T., Borowicz, S., Rader, J. H., Utzinger, U., Azhar, M., & Geest, J. P. V. (2011) · Microscopy and Microanalysis · doi:10.1017/s1431927610094341 · Cited by 33
“E-mail: jpv1@email.arizona.edu relationships in tissues via simultaneously imparting mechanical stimulation while noninvasively recording collagen or other biological signals ~Roeder et al., 2002; Voytik-Harbin et al., 2003; Hu et al., 2009!.”
MethodNichol, R. H., Catlett, T. S., Onesto, M. M., Hollender, D., & Gómez, T. M. (2019) · Stem Cell Reports · doi:10.1016/j.stemcr.2019.10.008 · Cited by 32
“This concentration of collagen produces dense matrices after 18 h of polymerization with peak linear modulus determined by tensile strength of the bulk material to be 5 kPa (Roeder et al., 2002).”
BackgroundGkretsi, V., Stylianou, A., & Stylianopoulos, T. (2017) · Experimental Cell Research · doi:10.1016/j.yexcr.2017.02.019 · Cited by 32
“Furthermore, the density of the fibers in the formed gels was increased with collagen concentration showing a correlation with collagen stiffness, as it has been previously shown in studies using collagen gels of increasing concentration [38,39].”
ResultConstitutive modeling of compressible type-I collagen hydrogels
Lane, B. A., Harmon, K. A., Goodwin, R. L., Yost, M. J., Shazly, T. M., & Eberth, J. F. (2018) · Medical Engineering & Physics · doi:10.1016/j.medengphy.2018.01.003 · Cited by 32
“, implantation, laboratory assay, drug delivery) [19].”
An indentation-based approach to determine the elastic constants of soft anisotropic tissues
Moghaddam, A. O., Wei, J., Kim, J., Dunn, A. C., & Johnson, A. J. W. (2019) · Journal of the mechanical behavior of biomedical materials/Journal of mechanical behavior of biomedical materials · doi:10.1016/j.jmbbm.2019.103539 · Cited by 32
Dennis, J. E., Whitney, G. A., Rai, J., Fernandes, R. J., & Kean, T. J. (2020) · Frontiers in Bioengineering and Biotechnology · doi:10.3389/fbioe.2020.590743 · Cited by 32
Supramolecular Nanofibrillar Polymer Hydrogels
Chau, M., Sriskandha, S. E., Thérien‐Aubin, H., & Kumacheva, E. (2015) · Advances in polymer science · doi:10.1007/978-3-319-15404-6_5 · Cited by 32
Snowhill, P. B., & Silver, F. H. (2005) · Cardiovascular Engineering An International Journal · doi:10.1007/s10558-005-9070-1 · Cited by 32
Elsaadany, M., Harris, M., & Yildirim-Ayan, E. D. (2017) · BioMed Research International · doi:10.1155/2017/3609703 · Cited by 31
Garoffolo, G., Ruiter, M. S., Piola, M., Brioschi, M., Thomas, A. C., Agrifoglio, M., Polvani, G., Coppadoro, L. P., Zoli, S., Saccu, C., et al. (2020) · Theranostics · doi:10.7150/thno.40595 · Cited by 31
“Young’s moduli were set according to the literature: Young’s moduli were set according to literature: 1 kPa for cells [10] 2 kPa for the adventitia (which was treated as a soft collagen matrix [11]) and 88 kPa for the media layer [12, 13].”
MethodElastic Modulus Measurement of Hydrogels
Lee, D.-H., Zhang, H., & Ryu, S. (2019) · Polymers and polymeric composites · doi:10.1007/978-3-319-77830-3_60 · Cited by 31
Marino, M., & Vairo, G. (2014) · Journal of the Mechanics and Physics of Solids · doi:10.1016/j.jmps.2014.08.009 · Cited by 31
Shanjani, Y., Kang, Y., Zarnescu, L., Bowden, A. K., Koh, J., Ker, D. F. E., & Yang, Y. (2016) · Journal of the mechanical behavior of biomedical materials/Journal of mechanical behavior of biomedical materials · doi:10.1016/j.jmbbm.2016.08.037 · Cited by 31
“The fibrillar structure of collagen hydrogel is determined by the polymerization conditions including collagen concentration and pH (Roeder et al., 2002).”
Nieskoski, M. D., Marra, K. A., Gunn, J. R., Kanick, S. C., Doyley, M. M., Hasan, T. G., Pereira, S. P., Trembly, B. S., & Pogue, B. W. (2017) · Journal of Biomechanical Engineering · doi:10.1115/1.4036392 · Cited by 31
“Provenzano combined the results from Roeder [34] with their own and showed a cubic relationship between elastic modulus and collagen concentrations (R(2)1⁄4 0.”
BackgroundInfluentialZhang, S., Cao, X., Stablow, A. M., Shenoy, V. B., & Winkelstein, B. A. (2016) · Journal of Biomechanical Engineering · doi:10.1115/1.4031975 · Cited by 30
“Further, stretching of those aligned fibers is a potential mechanism by which strain hardening rapidly increases stress in the collagen network at large bulk strains [49,74].”
BackgroundResultInfluentialHong, H., Kim, H., Han, S. J., Jang, J., Kim, H. K., Cho, D., & Kim, D. S. (2019) · Materials Science and Engineering C · doi:10.1016/j.msec.2019.109837 · Cited by 30
Schmid, H., Pauli, L., Paulus, A., Kuhl, E., & Itskov, M. (2011) · Computer Methods in Biomechanics & Biomedical Engineering · doi:10.1080/10255842.2010.548325 · Cited by 30
“The stress–strain relationship does then contain the Lagrange multiplier p. This is also called near incompressibility, alluding to the fact that in reality no material is absolutely incompressible. For more theoretical details and numerical implementations, please refer to Peng and Chang (1997) and Hartmann and Neff…”
BackgroundTechniques for assessing 3-D cell–matrix mechanical interactions in vitro and in vivo
Miron-Mendoza, M., Koppaka, V., Zhou, C., & Petroll, W. M. (2013) · Experimental Cell Research · doi:10.1016/j.yexcr.2013.06.018 · Cited by 30
“Fax: +1 214 648 E-mail address: m”
Rahimi, M., Mohseni-Kouchesfehani, H., Zarnani, A., Mobini, S., Nikoo, S., & Kazemnejad, S. (2014) · Journal of Biomaterials Applications · doi:10.1177/0885328213519835 · Cited by 30
Metadata
- Authors
- Roeder, B. A., Kokini, K., Sturgis, J. E., Robinson, J. P., & Voytik-Harbin, S. L.
- Affiliations
- Purdue University West Lafayette (US)
- Department of Basic Medical Sciences/Department of Biomedical Engineering, Purdue University, West Lafayette, IN 47907-1515
- Venue
- Journal of Biomechanical Engineering
- Publisher
- ASME International
- Published
- 2002-03-29
- Volume
- 124
- Issue
- 2
- Pages
- 214-222
- ISSN
- 0148-0731 (ISSN-L)
- 1528-8951
- OpenAlex
- W2133809313
- Semantic Scholar
- 6d026775d9662abbe0965c21925caeb1f0a96e7c
- Cited by
- 620
- References
- 41
- Citations by year
- 2026: 13 · 2025: 21 · 2024: 16 · 2023: 23 · 2022: 24 · 2021: 29 · 2020: 34 · 2019: 40 · 2018: 24 · 2017: 32 · 2016: 33 · 2015: 42 · 2014: 37 · 2013: 40 · 2012: 33
- FWCI
- 6.64
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Journal of Biomechanical Engineering (publishedVersion)
- PubMed (publishedVersion)
- Funders
- National Science Foundation
- Division of Graduate Education
- Topics
- Physical Sciences › Materials Science › Biomaterials › Collagen: Extraction and Characterization
- Life Sciences › Biochemistry, Genetics and Molecular Biology › Cell Biology › Cellular Mechanics and Interactions
- Physical Sciences › Materials Science › Biomaterials › Hydrogels: synthesis, properties, applications
- Keywords
- type I collagen, extracellular matrix, collagen fibrils, tensile properties, collagen content, fibril diameter, fibril length, strain rate sensitivity, stress-strain behavior, tissue engineering scaffolds, cell-matrix interactions, mechanotransduction
- MeSH terms
- Animals, Cattle, Elasticity, Extracellular Matrix, Hydrogen-Ion Concentration, Microscopy, Interference, Models, Biological, Polymers, Sensitivity and Specificity, Stress, Mechanical, Tensile Strength, Reproducibility of Results, Microscopy, Confocal, Collagen Type I, In Vitro Techniques
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.