CoChat

Tailoring Catalyst Morphology towards High Performance for Low Pt Loaded PEMFC Cathodes

Open access
Harzer, Gregor S., Orfanidi, Alin, El-Sayed, Hany, Madkikar, Pankaj, Gasteiger, Hubert A. · 2018 · Journal of The Electrochemical Society

The DOI matches its Crossref record; 41 of the 41 references it cites were found in a registry or an index.

Abstract

The effect of the catalyst synthesis method on the location of platinum nanoparticles on a high surface area Ketjenblack is investigated with respect to the high current density performance in low loaded proton exchange membrane fuel cells (PEMFC). Catalysts were prepared using various synthetic methods to deposit platinum nanoparticles at different locations on the carbon surface, e.g. inside or outside the pores of the primary particle. Transmission electron microscopy (TEM) suggested, that the Pt-particle deposition can be controlled to be preferentially on the outer carbon surface or within the pores. Electrochemical characterization was performed in thin-film rotating disk electrode (RDE) setup as well as in 5 cm 2 single cell MEA tests. Although the carbon support was identical for all catalysts, the one with more Pt particles deposited on the outer carbon surface performed superior at high current which was attributed to a lower oxygen mass transport resistance. From the presented data, it can be concluded that not only the type or the surface area of the carbon black support affects the fuel cell performance, but that the synthesis approach is an additional parameter to tune the fuel cell performance at high current density.

Overview

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.1149/2.0311810jes

Cites

41 of 41 references verified0 citation errors · 0 not checkable

Statistics

Figures

Image 1
From the PDF
Image 2
From the PDF
Image 3
From the PDF
Image 4
From the PDF
Image 5
From the PDF
Figure 1 XP spectra in the N 1s region of the as-received Ketjenblack (KB), the oxidized Ketjenblack (KB-ox), and the Ketjenblack after the NHx functionalization (KB(NHx)).
Figure 1 XP spectra in the N 1s region of the as-received Ketjenblack (KB), the oxidized Ketjenblack (KB-ox), and the Ketjenblack after the NHx functionalization (KB(NHx)).From the PDF
Figure 2 TEM micrographs and the corresponding particle size distribution for the various catalysts: (a) Pt/KBPO; (b) Pt/KB(NHx)PO; (c) Pt/KBIW; and, (d) Pt/KBTKK. dN denotes the number averaged diameter and their corresponding standard deviation, whereas dS denotes the surface normalized diameter calculated by Equation 1. Simplified schematic representation of primary carbon particle (gray) with Pt nanoparticles (black) deposited preferentially on (e) the outside of the carbon support (hypothesized to be the case for Pt/KBPO and Pt/KB(NHx)PO) and (f) on the inside of the carbon support (hypothesized to be the case for Pt/KBIW and Pt/KBTKK).
Figure 2 TEM micrographs and the corresponding particle size distribution for the various catalysts: (a) Pt/KBPO; (b) Pt/KB(NHx)PO; (c) Pt/KBIW; and, (d) Pt/KBTKK. dN denotes the number averaged diameter and their corresponding standard deviation, whereas dS denotes the surface normalized diameter calculated by Equation 1. Simplified schematic representation of primary carbon particle (gray) with Pt nanoparticles (black) deposited preferentially on (e) the outside of the carbon support (hypothesized to be the case for Pt/KBPO and Pt/KB(NHx)PO) and (f) on the inside of the carbon support (hypothesized to be the case for Pt/KBIW and Pt/KBTKK).From the PDF
Figure 3 Simplified schematic representation of the synthetic methods and the time dependent formation of Pt particles; red color intensity depicts Pt precursor concentration. A) Reduction of a highly diluted Pt precursor in ethylene glycol in the polyol method, with a formation of Pt nanoparticles preferentially on the outside of the carbon surface and in the solution. B) Incipient wetness method, in which the carbon support is impregnated with a highly concentrated Pt precursor solution, so that a high concentration of Pt precursor is present inside the pores, leading to more particles deposited inside the carbon.
Figure 3 Simplified schematic representation of the synthetic methods and the time dependent formation of Pt particles; red color intensity depicts Pt precursor concentration. A) Reduction of a highly diluted Pt precursor in ethylene glycol in the polyol method, with a formation of Pt nanoparticles preferentially on the outside of the carbon surface and in the solution. B) Incipient wetness method, in which the carbon support is impregnated with a highly concentrated Pt precursor solution, so that a high concentration of Pt precursor is present inside the pores, leading to more particles deposited inside the carbon.From the PDF
Figure 4 a) Uncorrected H2/O2 polarization curves (80 ◦ C, 100% RH , H2/O2 (2000/5000 nccm), 170 kPaabs) for the different catalysts with ultra-low cathode Pt loading (62-64 μ gPt/cm 2 MEA , see Table III) and the corresponding high frequency resistance ( RHFR ). b) Performance curves normalized to the Pt loading and corrected for the HFR ( R HFR), the effective proton conduction resistance of the cathode catalyst layer ( R eff H + , cath ) as well as H2 crossover ( i x, H 2 ) and shorting currents. The anode platinum loading was ≈ 100 μ gPt/cm 2 MEA for all MEAs. The error bars correspond to the mean absolute deviation between two independent measurements.
Figure 4 a) Uncorrected H2/O2 polarization curves (80 ◦ C, 100% RH , H2/O2 (2000/5000 nccm), 170 kPaabs) for the different catalysts with ultra-low cathode Pt loading (62-64 μ gPt/cm 2 MEA , see Table III) and the corresponding high frequency resistance ( RHFR ). b) Performance curves normalized to the Pt loading and corrected for the HFR ( R HFR), the effective proton conduction resistance of the cathode catalyst layer ( R eff H + , cath ) as well as H2 crossover ( i x, H 2 ) and shorting currents. The anode platinum loading was ≈ 100 μ gPt/cm 2 MEA for all MEAs. The error bars correspond to the mean absolute deviation between two independent measurements.From the PDF
Figure 5 Polarization curves in air (solid lines) and 10% O2 in N2 (dashed lines) at 80 ◦ C, 100% RH , 2000/5000 nccm (A/C) at 170 kPaabs for the different catalysts with a cathode loading of 62-64 μ gPt/cm 2 MEA (see Table III) and anode loadings of ≈ 100 μ gPt/cm 2 MEA . Error bars represent the mean absolute deviation from two independent measurements.
Figure 5 Polarization curves in air (solid lines) and 10% O2 in N2 (dashed lines) at 80 ◦ C, 100% RH , 2000/5000 nccm (A/C) at 170 kPaabs for the different catalysts with a cathode loading of 62-64 μ gPt/cm 2 MEA (see Table III) and anode loadings of ≈ 100 μ gPt/cm 2 MEA . Error bars represent the mean absolute deviation from two independent measurements.From the PDF
Figure 6 Cathode catalyst layer proton resistivity, ρ H + cath , determined from impedance spectroscopy at 50, 70 and 100% RH . Error bars represent the mean absolute deviation from two independent measurements.
Figure 6 Cathode catalyst layer proton resistivity, ρ H + cath , determined from impedance spectroscopy at 50, 70 and 100% RH . Error bars represent the mean absolute deviation from two independent measurements.From the PDF
Figure 7 Total oxygen mass transport resistance divided into pressure dependent transport resistance ( R PD O 2 , hatched bar) and pressure independent transport resistance ( R PD O 2 , open bar) determined from limiting current measurements at 80 ◦ C, 70% RH , differential-flow (2000/5000 nccm) and 170, 270, 350, 500 kPaabs at various O2 concentrations. Simplified sketch depicting the different transport limitations depending on the location of the Pt particles on the carbon black support with additional resistance for the Pt particles inside the pore.
Figure 7 Total oxygen mass transport resistance divided into pressure dependent transport resistance ( R PD O 2 , hatched bar) and pressure independent transport resistance ( R PD O 2 , open bar) determined from limiting current measurements at 80 ◦ C, 70% RH , differential-flow (2000/5000 nccm) and 170, 270, 350, 500 kPaabs at various O2 concentrations. Simplified sketch depicting the different transport limitations depending on the location of the Pt particles on the carbon black support with additional resistance for the Pt particles inside the pore.From the PDF
Figure 8 a) solid lines: polarization curves (H2/air - differential-flow, 80 ◦ C, 100% RH , 170 kPaabs) corrected by the HFR ( R HFR), the effective proton conduction resistance of the catalyst layer ( R eff H + , cath ), and the total oxygen mass transport resistance ( R total O 2 ); dotted lines: purely ORR kinetics limited polarization curves (black/red lines) determined from Equation 5 in Ref. 15 for the effective O2 partial pressure of 25.8 kPa under these conditions. b) Unaccounted voltage losses obtained from the difference between the purely ORR kinetics limited performance (dotted lines in a) and the fully corrected H2/air polarization curves (solid lines in a) for Pt/KBPO, Pt/KB(NHx)PO, Pt/KBIW, and Pt/KBTKK.
Figure 8 a) solid lines: polarization curves (H2/air - differential-flow, 80 ◦ C, 100% RH , 170 kPaabs) corrected by the HFR ( R HFR), the effective proton conduction resistance of the catalyst layer ( R eff H + , cath ), and the total oxygen mass transport resistance ( R total O 2 ); dotted lines: purely ORR kinetics limited polarization curves (black/red lines) determined from Equation 5 in Ref. 15 for the effective O2 partial pressure of 25.8 kPa under these conditions. b) Unaccounted voltage losses obtained from the difference between the purely ORR kinetics limited performance (dotted lines in a) and the fully corrected H2/air polarization curves (solid lines in a) for Pt/KBPO, Pt/KB(NHx)PO, Pt/KBIW, and Pt/KBTKK.From the PDF
Figure 9 Differential-flow polarization curves in H2/O2 at 170 kPaabs, 80 ◦ C, 100% RH (solid lines) and 70% RH (dashed lines) after correction of the measured cell voltage by the HFR ( R HFR) and catalyst layer effective proton conduction resistance ( R eff H + , cath ). Error bars correspond to the mean absolute deviation from two independent measurements.
Figure 9 Differential-flow polarization curves in H2/O2 at 170 kPaabs, 80 ◦ C, 100% RH (solid lines) and 70% RH (dashed lines) after correction of the measured cell voltage by the HFR ( R HFR) and catalyst layer effective proton conduction resistance ( R eff H + , cath ). Error bars correspond to the mean absolute deviation from two independent measurements.From the PDF
Figure 10 Differential-flow polarization curves in H2/10% O2 (balance N2) at 80 ◦ C, 170 kPaabs, 100% RH (solid lines) and 70% RH (dashed lines) for all catalysts after correction of the cell voltage by the HFR ( R HFR) and catalyst layer effective proton conduction resistance ( R eff H + , cath ). Error bars correspond to the mean absolute deviation of two independent measurements.
Figure 10 Differential-flow polarization curves in H2/10% O2 (balance N2) at 80 ◦ C, 170 kPaabs, 100% RH (solid lines) and 70% RH (dashed lines) for all catalysts after correction of the cell voltage by the HFR ( R HFR) and catalyst layer effective proton conduction resistance ( R eff H + , cath ). Error bars correspond to the mean absolute deviation of two independent measurements.From the PDF

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Claims other papers make about this one

Each is checked against this paper’s own text: does it say what the citing paper says it does?

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cites

Show all 41 references

Cited by

See all 146

Metadata

Authors
Harzer, G. S., Orfanidi, A., El-Sayed, H., Madkikar, P., & Gasteiger, H. A.
Affiliations
Technical University of Munich (DE)
Venue
Journal of The Electrochemical Society
Published
2018
Volume
165
Issue
10
Pages
F770-F779
ISSN
  • 0013-4651 (ISSN-L)
  • 1945-7111
OpenAlex
W2863715742
Cited by
146
References
41
Citations by year
2026: 10 · 2025: 20 · 2024: 26 · 2023: 18 · 2022: 18 · 2021: 29 · 2020: 13 · 2019: 11 · 2018: 1
FWCI
5.17
Type
journal article
Language
en
Open access
Licence
cc-by
Locations
  • Journal of The Electrochemical Society (publishedVersion, cc-by)
  • mediaTUM – the media and publications repository of the Technical University Munich (Technical University Munich) (submittedVersion, other-oa)
Topics
  • Physical Sciences › Engineering › Electrical and Electronic Engineering › Fuel Cells and Related Materials
  • Physical Sciences › Energy › Renewable Energy, Sustainability and the Environment › Electrocatalysts for Energy Conversion
  • Physical Sciences › Materials Science › Materials Chemistry › Catalytic Processes in Materials Science
Keywords
platinum nanoparticles, catalyst morphology, proton exchange membrane fuel cells, low platinum loading, Ketjen Black, carbon black support, catalyst synthesis methods, oxygen reduction reaction

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Tailoring Catalyst Morphology towards High Performance for Low Pt Loaded PEMFC Cathodes. https://app.cochat.ai/papers/10.1149/2.0311810jes
The paper
Harzer, G. S., Orfanidi, A., El-Sayed, H., Madkikar, P., & Gasteiger, H. A. (2018). Tailoring Catalyst Morphology towards High Performance for Low Pt Loaded PEMFC Cathodes. Journal of The Electrochemical Society. https://doi.org/10.1149/2.0311810jes

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.