Scalable nanoporous carbon films allow line-of-sight 3D atomic layer deposition of Pt: towards a new generation catalyst layer for PEM fuel cells.
Open accessThe DOI matches its Crossref record; 42 of the 42 references it cites were found in a registry or an index; 5 of the 24 sources its claims cite were checked for support.
Abstract
A self-supported, binder-free and scalable nanoporous carbon scaffold serves as an excellent host for the efficient and uniform atomic layer deposition of Pt nanoparticles, showing exemplary performance as a cathode catalyst layer in a PEM fuel cell.
Overview
CoChat Summary
TL;DR
The paper develops binderless, self-supported nanoporous carbon scaffold (NCS) films with tunable 5–100+ nm pores and uses them for line-of-sight 3D atomic layer deposition (ALD) of Pt nanoparticles as PEM fuel cell cathode catalyst layers. The optimal Pt30/NCS85 cathode gives ~0.4 mA cm⁻² Pt specific activity, 0.25 A mg Pt⁻¹ mass activity, and a maximum power density of 1230 mW cm⁻² (IR-corrected), outperforming two commercial Pt/C benchmarks under comparable conditions.
Key findings
- NCS membranes are binderless, 100% carbon, scalable in area (1–150+ cm²) and thickness (1–1000 µm), with tunable monodisperse pores (5–100+ nm), high surface area (ca. 200–575 m² g⁻¹), ~90% porosity, and conductivity ≥2 S cm⁻¹.
- ALD of Pt into 12 µm-thick NCS85 gives uniform Pt nanoparticles through the full thickness: average sizes are 3 nm for Pt20/NCS85, 5 nm for Pt30/NCS85, and 6.4 nm for Pt40/NCS85; agglomeration is seen only at 40 cycles.
- In MEA testing, Pt30/NCS85 (0.44 mg Pt cm⁻²) gives specific activity ~0.4 mA cm⁻² Pt and mass activity 0.25 A mg Pt⁻¹, with a maximum power density of 1230 mW cm⁻² (IR-corrected) and limiting current density approaching 3 A cm⁻².
- Pt30/NCS85 and Pt40/NCS85 outperform two commercial Pt/C catalyst layers (GDE and CCM) with comparable Pt loadings under identical conditions; Pt10/NCS22 deposits uniformly but performs poorly in the MEA due to difficult Nafion infiltration.
Methods
- NCS fabrication: ball-milled mesophase pitch/PVA/1,3-propanediol/silica slurries were tape-cast, carbonized at 900 °C, and silica-templated pores removed with NaOH; pore size was controlled by silica particle size (8, 22, 50, 85 nm).
- Pt ALD: MeCpPtMe₃ precursor and air oxidant at 190 °C, with 20, 30, and 40 cycles on NCS85 and 10 cycles on NCS22; characterization included FESEM, TEM/HR-TEM, EDS, XRD, TPD, gas sorption, conductivity, CV, and EIS.
- MEA testing: Nafion was drop-cast into Pt/NCS films, hot-pressed with a commercial anode-coated membrane, and tested at 80 °C, 100% RH, and 150 kPa absolute backpressure in H₂/O₂ and H₂/air; commercial GDE (0.5 mg Pt cm⁻²) and CCM (0.4 mg Pt cm⁻²) were benchmarks.
Limitations
- The paper states that Nafion infiltration and loading were not optimized, that durability under MEA conditions remains to be established, and that the catalyst layers have not yet been fully optimized.
- The paper states that Pt40/NCS85 likely suffers pore-neck blockage and possible flooding at high Pt loading, and that Pt10/NCS22 performs poorly because Nafion cannot easily infiltrate its small pores/necks.
- The paper states that mass transport performance is not as good as the commercial CCM benchmark or several leading ink-based Pt/C catalysts; evident from the text, the study focuses primarily on NCS85 and does not report long-term durability data.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
4 Valid · 0 Not valid · 13 Not checked · 67 Own results and interpretations
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“However, at high current densities, limitations related to local oxygen transport are likely the problem.42”
§ Scalable nanoporous carbon films allow line-ofsight 3D atomic layer deposition of Pt: towards a new generation catalyst layer for PEM fuel cells † > À2
What the sources say
- Partly supportedcites [42] Kongkanand, 2016, J. Phys. Chem. Lett. sourceExperimental — accuracy not yet measured
The Recent Progress section says local oxygen-transport resistance is a major contributor to performance loss at high current density in low-Pt cathodes. It does not examine Pt20/NCS85, so it supports the proposed mechanism but not its application to that specific catalyst (searched: Pt20/NCS85). No page number was provided in our copy. (LLM, conf=0.85)
hedgedstates a possible cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The sources with a verdict support this claim; the rest weren’t checked yet, have no full text we could read, or their verdicts aren’t rated yet.
In the paper
“Furthermore, the performance of our ALD Pt/NCS85 catalysts approaches that of the best specific and mass activities reported for several conventional ink-based Pt/C catalysts.35,[38][39][40]”
§ Scalable nanoporous carbon films allow line-ofsight 3D atomic layer deposition of Pt: towards a new generation catalyst layer for PEM fuel cells † > This journal is © The Royal Society of Chemistry 2021
What the sources say
- Supportedcites [35] Harzer, 2018, J. Electrochem. Soc. source
This paper supplies a conventional Pt/C benchmark for the citing authors’ comparison: the Experimental section (p. 3) describes ink-prepared catalyst layers, and Results and Discussion (pp. 6–7) reports their specific and mass activities. The claim that ALD Pt/NCS85 approaches those values is the citing authors’ comparison, not a finding attributed to this source alone. (LLM, conf=0.87)
- Not checked — no full text of the sourcecites [38] Gasteiger, 2005, Appl. Catal., B source
- Not checked — no full text of the sourcecites [39] Ott, 2020, Nat. Mater. source
- Could not verifycites [40] Yarlagadda, 2018, ACS Energy Lett. sourceExperimental — accuracy not yet measured
The Main Text (pp. 3, 7) compares the activity and fuel-cell performance of catalysts on different carbon supports, but does not address ALD Pt/NCS85. Searches for ALD Pt/NCS85 and for specific and mass activities of conventional ink-based Pt/C catalysts found no comparison supporting the cited claim. (LLM, conf=0.74)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“While the Yarlagadda Pt/C catalyst does out-perform our ALD Pt/NCS85 materials in the kinetic region, 40 it remains clear that our new catalyst layers are very promising for future PEM fuel cell applications, especially as they have not yet been fully optimized.”
§ Scalable nanoporous carbon films allow line-ofsight 3D atomic layer deposition of Pt: towards a new generation catalyst layer for PEM fuel cells † > À2
What the sources say
- Partly supportedcites [40] Yarlagadda, 2018, ACS Energy Lett. sourceExperimental — accuracy not yet measured
The Main Text (p. 7) reports that Yarlagadda’s Pt/HSC-e catalyst outperforms the other catalysts tested at low current density, relevant to the kinetic region. It does not discuss the citing authors’ ALD Pt/NCS85 materials, so it cannot establish the stated comparison with them. (LLM, conf=0.84)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
In the paper
“with tunable and monodisperse pores (5-100+ nm)”
- Also stated in: § 1. Introduction · plain
“we have developed a nanoporous carbon scaffold (NCS) with a fully tunable and monodisperse pore size in the range of 5-100 nm in diameter.8”
§ Scalable nanoporous carbon films allow line-ofsight 3D atomic layer deposition of Pt: towards a new generation catalyst layer for PEM fuel cells † > Abstract
What the sources say
- Not matchedcites [8] V.Birss , X.Li , D.Banham and D. Y.Kwok , WO2015135069A1PCT/CA2015/000516, 2015
Couldn’t be matched to a paper in Crossref, so it can’t be checked.
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Also stated in: § 1. Introduction · plain
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Cells constructed with an optimal ALD Pt loading of 30 cycles are shown to exhibit a specific activity of Z0.4 mA cm À2 Pt”
- Also stated in: § 1. Introduction · plain
“A specific activity of 0.40 mA cm À2 Pt was obtained for the best performing 30 ALD cycle NCS85 catalyst.”
§ Scalable nanoporous carbon films allow line-ofsight 3D atomic layer deposition of Pt: towards a new generation catalyst layer for PEM fuel cells † > Abstract
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Also stated in: § 1. Introduction · plain
37 more claims
Create a free account to see all 84 claims and every source verdict.
- It may state two separate claims as one. 36
- Probably not a substantial claim. 6
- The quote only partly states this claim. 2
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
“The ECSA values of Pt30/NCS85 and Pt40/ NCS85 are similar (5.0 Æ 0.7 and 6.4 Æ 1.1 nm, respectively) as their Pt NPs are similar in size, while the Pt20/NCS85 material has the largest ECSA (64.5 m 2 g Pt À1 )”
§ Scalable nanoporous carbon films allow line-ofsight 3D atomic layer deposition of Pt: towards a new generation catalyst layer for PEM fuel cells † > This journal is © The Royal Society of Chemistry 2021
Reported 1 · recomputed 59.5
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
“the electrochemically active surface area (ECSA in m 2 g À1 , calculated by dividing the gravimetric capacitance by 0.15 F m À2 , a commonly used area-specific capacitance) ranges from 200-500 m 2 g À1”
§ Scalable nanoporous carbon films allow line-ofsight 3D atomic layer deposition of Pt: towards a new generation catalyst layer for PEM fuel cells † > 2.1 NCS preparation and physical properties
Reported 500 · recomputed 800
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Scalable nanoporous carbon films allow line-ofsight 3D atomic layer deposition of Pt: towards a new generation catalyst layer for PEM fuel cells † > 2.1 NCS preparation and physical properties
“The precursor membrane is then heated at 900 1C in nitrogen to remove PD and PVA, imprinted with SiO 2 , and then carbonized, followed by removal of the silica in strong base.”
§ Scalable nanoporous carbon films allow line-ofsight 3D atomic layer deposition of Pt: towards a new generation catalyst layer for PEM fuel cells † > 4.2 NCS preparation
“These films were imprinted in an alumina tubular furnace at 400 1C for 2 h in nitrogen, heated at 900 1C for 2 h to achieve carbonization”
Citations
Cites
Physical chemistry of surfaces
(1998) · Choice Reviews Online · doi:10.5860/choice.35-4499 · Cited by 11,648
Gasteiger, H. A., Kocha, S. S., Sompalli, B., & Wagner, F. T. (2005) · Applied Catalysis B: Environmental · doi:10.1016/j.apcatb.2004.06.021 · Cited by 4,876
Physical chemistry of surfaces
Taylor, P. (1991) · Colloids and Surfaces · doi:10.1016/0166-6622(91)80262-m · Cited by 2,811
Carbon—Electrochemical and Physicochemical Properties
Brown, O. R. (1989) · Electrochimica Acta · doi:10.1016/0013-4686(89)87066-5 · Cited by 1,211
Kongkanand, A., & Mathias, M. F. (2016) · The Journal of Physical Chemistry Letters · doi:10.1021/acs.jpclett.6b00216 · Cited by 1,202
Liu, D., Li, X., Chen, S., Yan, H., Wang, C., Wu, C., Haleem, Y. A., Duan, S., Lu, J., Ge, B., et al. (2019) · Nature Energy · doi:10.1038/s41560-019-0402-6 · Cited by 1,166
Self-citationNanostructured high-energy cathode materials for advanced lithium batteries
Sun, Y.-K., Chen, Z., Noh, H.-J., Lee, D.-J., Jung, H.-G., Ren, Y., Wang, S., Yoon, C. S., Myung, S.-T., & Amine, K. (2012) · Nature Materials · doi:10.1038/nmat3435 · Cited by 1,093
Yan, H., Cheng, H., Yi, H., Lin, Y., Yao, T., Wang, C., Li, J., Wei, S., & Lu, J. (2015) · Journal of the American Chemical Society · doi:10.1021/jacs.5b06485 · Cited by 1,091
Promoting direct interspecies electron transfer with activated carbon
Liu, F., Rotaru, A.-E., Shrestha, P. M., Malvankar, N. S., Nevin, K. P., & Lovley, D. R. (2012) · Energy & Environmental Science · doi:10.1039/c2ee22459c · Cited by 879
Shao, M., Peles, A., & Shoemaker, K. (2011) · Nano Letters · doi:10.1021/nl2017459 · Cited by 878
Research works printed but not linked: 3
- M.Atwa , X.Li , F.Forouzandeh , S.Luong , E.Bertin , M. J.Parnian , K.Karan and V.Birss , in Low-Temp. fuel cells, electrolysers & H2 processing , ed. A. Gasteiger and H. Bandarenka , Lucerne , 2019 , pp. 112–120
- Yao, 2016, Adv. Mater. Interfaces, 3, 3
- Philips’Gloeilampenfabrieken, 1958, Philips Res. Rep., 13, 1
Cited by
Pt–C interactions in carbon-supported Pt-based electrocatalysts
Xiao, Y., Ying, J. R., Liu, H.-W., & Yang, X. (2023) · Frontiers of Chemical Science and Engineering · doi:10.1007/s11705-023-2300-5 · Cited by 46
Methods—A Practical Approach to the Reversible Hydrogen Electrode Scale
Zeledon, J. A. Z., Jackson, A., Stevens, M. B., Kamat, G. A., & Jaramillo, T. F. (2022) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/ac71d1 · Cited by 37
Sun, R., Wu, R.-Z., Li, X., Feng, J., Zhang, L., & Wang, A. (2022) · Journal of Colloid and Interface Science · doi:10.1016/j.jcis.2022.04.043 · Cited by 29
Self-citationWu, X., Xing, S. J., Luo, J., Wang, H., Huang, F., & Zhao, C. (2025) · Energy Reviews · doi:10.1016/j.enrev.2025.100130 · Cited by 39
Liu, X., Su, Y., & Chen, R. (2023) · International Journal of Extreme Manufacturing · doi:10.1088/2631-7990/acc6a7 · Cited by 36
Metadata
- Authors
- Atwa, M., Li, X., Wang, Z., Dull, S., Xu, S., Tong, X., Tang, R., Nishihara, H., Prinz, F., & Birss, V.
- Affiliations
- Suez Canal University (EG)
- University of Calgary (CA)
- Stanford University (US)
- Institute of Multidisciplinary Research for Advanced Materials, Tohoku University (JP)
- Norwegian University of Science and Technology (NO)
- Corresponding author
- Birss, Viola
- ORCID
- Venue
- Materials Horizons
- Publisher
- Royal Society of Chemistry (RSC)
- Published
- 2021
- Volume
- 8
- Issue
- 9
- Pages
- 2451-2462
- ISSN
- 2051-6347 (ISSN-L)
- 2051-6355
- OpenAlex
- W3195291835
- Semantic Scholar
- da087dc4173b7213e477bf3561fdd293e5731de1
- Cited by
- 36
- References
- 42
- Citations by year
- 2026: 5 · 2025: 5 · 2024: 7 · 2023: 9 · 2022: 10
- FWCI
- 1.91
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Licence
- Locations
- Materials Horizons (publishedVersion, cc-by-nc)
- PubMed (publishedVersion)
- Funders
- Canada Research Chairs
- Volkswagen of America
- Natural Sciences and Engineering Research Council of Canada
- National Science Foundation (ECCS-1542152)
- Ministry of Education, Culture, Sports, Science and Technology
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Fuel Cells and Related Materials
- Physical Sciences › Energy › Renewable Energy, Sustainability and the Environment › Electrocatalysts for Energy Conversion
- Physical Sciences › Materials Science › Materials Chemistry › Catalytic Processes in Materials Science
- Keywords
- atomic layer deposition, platinum nanoparticles, proton exchange membrane fuel cells, cathode catalyst layer
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-09-28, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-09-28 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Scalable nanoporous carbon films allow line-of-sight 3D atomic layer deposition of Pt: towards a new generation catalyst layer for PEM fuel cells. https://app.cochat.ai/papers/10.1039/d1mh00268f
- The paper
- Atwa, M., Li, X., Wang, Z., Dull, S., Xu, S., Tong, X., Tang, R., Nishihara, H., Prinz, F., & Birss, V. (2021). Scalable nanoporous carbon films allow line-of-sight 3D atomic layer deposition of Pt: towards a new generation catalyst layer for PEM fuel cells. Materials Horizons. https://doi.org/10.1039/d1mh00268f
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.