Optimization of Process Parameters with Minimum Thrust Force and Torque in Drilling Operation Using Taguchi Method
Open accessThe DOI matches its Crossref record; 25 of the 25 references it cites were found in a registry or an index.
Abstract
This research outlines the Taguchi optimization methodology, which is applied to optimize cutting parameters in drilling of AISI 1040 steel. The drilling parameters evaluated are cutting speed, feed rate, and helix angle. Series of experiments are conducted to relate the cutting parameters on the thrust force and torque. L 27 (3 13 ) orthogonal array, signal-to-noise ratio is employed to analyze the influence of these parameters on thrust force and torque during drilling. Analysis of variance (ANOVA) is used to study the effect of process parameters on machining process. The study shows that the Taguchi method is suitable to solve the stated problem with the minimum number of trials. The main objective is to find the important factors and combination of factors that influence the machining process to achieve low thrust force and torque. The analysis of the Taguchi method indicates that the feed rate is the most significant factor affecting the thrust force, while the cutting speed contributes the most to the torque.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Citations
Cites
Application of Taguchi method in the optimization of end milling parameters
Ghani, J. A., Choudhury, I. A., & Hassan, H. H. (2004) · Journal of Materials Processing Technology · doi:10.1016/s0924-0136(03)00865-3 · Cited by 766
Noordin, M. Y., Venkatesh, V. C., Sharif, S., Elting, S., & Abdullah, A. (2004) · Journal of Materials Processing Technology · doi:10.1016/s0924-0136(03)00861-6 · Cited by 739
Delamination During Drilling in Composite Laminates
Ho-Cheng, H., & Dharan, C. K. H. (1990) · Journal of Engineering for Industry · doi:10.1115/1.2899580 · Cited by 572
Delamination in drilling GFR-thermoset composites
Khashaba, U. A. (2004) · Composite Structures · doi:10.1016/s0263-8223(03)00180-6 · Cited by 344
Tsao, C. C., & Hocheng, H. (2008) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2006.04.126 · Cited by 281
Experimental investigation and optimisation in drilling of GFRP composites
Palanikumar, K. (2011) · Measurement · doi:10.1016/j.measurement.2011.07.023 · Cited by 275
Mohan, N. S., Ramachandra, A., & Kulkarni, S. M. (2005) · Composite Structures · doi:10.1016/j.compstruct.2005.09.039 · Cited by 201
Pawade, R. S., & Joshi, S. S. (2011) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-011-3183-z · Cited by 199
Kurt, M., Bagci, E., & Kaynak, Y. (2009) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-007-1368-2 · Cited by 198
Elsayed, K., & Lacor, C. (2011) · Powder Technology · doi:10.1016/j.powtec.2011.10.015 · Cited by 155
Research works printed but not linked: 1
- Roy R. K., 1990, A Primer of Taguchi Method
Cited by
A review: drilling performance and hole quality of aluminium alloys for aerospace applications
Aamir, M., Giasin, K., Tolouei-Rad, M., & Vafadar, A. (2020) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2020.09.003 · Cited by 286
Aamir, M., Tu, S., Tolouei-Rad, M., Giasin, K., & Vafadar, A. (2020) · Materials · doi:10.3390/ma13030680 · Cited by 86
“Conventional drilling is considered to be the most economical and efficient machining processes in the aerospace and automotive industries [1].”
BackgroundAamir, M., Tolouei‐Rad, M., Giasin, K., & Vafadar, A. (2020) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-020-06151-7 · Cited by 35
Huang, W., Tasi, Z.-Y., Ho, W., & Chou, J. (2022) · Polymers · doi:10.3390/polym14030644 · Cited by 29
Aamir, M., Tolouei‐Rad, M., & Giasin, K. (2021) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-021-07082-7 · Cited by 19
Gök, F., Orak, S., & Sofuoğlu, M. A. (2020) · Soft Computing · doi:10.1007/s00500-020-05022-3 · Cited by 18
Yıldız, T., & Sur, G. (2021) · Proceedings of the Institution of Mechanical Engineers Part B Journal of Engineering Manufacture · doi:10.1177/0954405421995657 · Cited by 17
Optimisation of drilling parameters on St37 based on Taguchi method
Samavi, J., Goharimanesh, M., Akbari, A., & Dezyani, E. (2018) · Journal of the Brazilian Society of Mechanical Sciences and Engineering · doi:10.1007/s40430-018-1245-y · Cited by 11
Aras, S., & Tarakçıoğlu, N. (2021) · Journal of Composite Materials · doi:10.1177/0021998321997532 · Cited by 11
Optimization approach using L16 Taguchi design to improve FSW parameters for AA2017-T4 weld joints
Lakache, H. E., Belattar, A., May, A., Merazga, C., Chergui, T., Lahmar, H., & Mokdad, A. (2025) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-025-15831-1 · Cited by 10
Imran, A., Kim, S.-H., Woo, J., & Yi, B.-J. (2022) · IEEE Access · doi:10.1109/access.2022.3210247 · Cited by 9
Riaz, A. A., Muhammad, R., Ullah, N., Hussain, G., Alkahtani, M. S., & Akram, W. (2021) · Metals · doi:10.3390/met11020277 · Cited by 9
Kumar, R. S., Mohanraj, M., Natarajan, P., Julias, A. A., & Sathyamurthy, R. (2021) · Journal of Natural Fibers · doi:10.1080/15440478.2021.1993412 · Cited by 7
JaisonBaby, & Shunmugesh, K. (2019) · Materials Today Proceedings · doi:10.1016/j.matpr.2018.12.024 · Cited by 6
Multi-objective optimization of submerged friction stir welding parameters for Al-Cu-Mg alloy
Lakache, H. E., May, A., Belattar, A., Berkani, A. A., & Hamici, I. (2025) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-025-16214-2 · Cited by 5
Riaz, M., Sharif, A., & Siddiqi, M. U. R. (2022) · Journal of Engineering and Applied Sciences , University of Engineering and Technology, Peshawar · doi:10.17582/journal.jeas/41.44.55 · Cited by 5
Statistical learning-driven parameter tuning in injection molding using modified simplex method
Luangpaiboon, P., Atthirawong, W., Hirunwat, A., & Aungkulanon, P. (2025) · Results in Engineering · doi:10.1016/j.rineng.2025.106690 · Cited by 5
Prabhu, P., Mahalingam, S. K., Shajahan, M. I., Balaji, A., & Karthikeyan, B. (2021) · Surface Review and Letters · doi:10.1142/s0218625x22500147 · Cited by 4
Oke, S. A., & Odusoro, S. I. (2021) · International Journal of Industrial Engineering and Engineering Management · doi:10.24002/ijieem.v3i1.4414 · Cited by 4
Narayanan, B., & Muthusamy, S. (2023) · Journal of Intelligent & Fuzzy Systems · doi:10.3233/jifs-231412 · Cited by 3
Determination of Temperature Effects on Cortical Bone Milling Using Taguchi Method
Kağıtcı, Y. Ç., & Neşeli, S. (2025) · Arabian Journal for Science and Engineering · doi:10.1007/s13369-025-10115-y · Cited by 1
Kanagaraju, T., Samsingh, R. V., David, A. G., Ramachandran, A., & Selvam, A. (2025) · Proceedings of the Institution of Mechanical Engineers Part E Journal of Process Mechanical Engineering · doi:10.1177/09544089251331267 · Cited by 1
Sivam, S. P. S. S., Banerjee, A., & Kulkarni, A. (2019) · SAE technical papers on CD-ROM/SAE technical paper series · doi:10.4271/2019-28-0055 · Cited by 1
Oke, S. A., & Odusoro, S. I. (2021) · International Journal of Industrial Engineering and Engineering Management · doi:10.24002/ijieem.v3i2.5458 · Cited by 1
Lubin, R., & Bharathiraja, G. (2022) · Journal of Pharmaceutical Negative Results · doi:10.47750/pnr.2022.13.s04.046 · Cited by 1
Li, M., & Wang, S.-T. (2018) · Applied Sciences · doi:10.3390/app8122382
Cervantes, C., & Arman, E. N. (2018) · KTH Publication Database DiVA (KTH Royal Institute of Technology)
Exploration of machining parameters by using Taguchi technique on MAAJDM
Anjaneyulu, B., Vardhan, D. H., Reddy, R. M., Tarigonda, H., & Rani, M. U. (2023) · Materials Today Proceedings · doi:10.1016/j.matpr.2023.05.067
Parameters Optimization on Abrasive Water Jet Machining of Zerconia Ceramics
Anjaneyulu, B., Bhuvaneswar, P., Amaranath, K., Reddy, A. C., Althaf, S. S. M., & Charan, V. (2024) · International Journal for Research in Applied Science and Engineering Technology · doi:10.22214/ijraset.2024.59116
Oluwo, A. A., Ogunmola, B. Y., Oke, S. A., Rajan, A. J., Jose, S., & Lathashankar, B. (2025) · Science, Engineering and Health Studies · doi:10.69598/sehs.19.25040002
Naga Sivamma, N. (2026) · REST Journal on Emerging trends in Modelling and Manufacturing · doi:10.46632/jemm/12/3/1
Optimization of Drilling Parameters for Improved Surface Quality Using Taguchi Method
Wijesekara, G. (2015) · International Journal on Theoretical and Applied Research in Mechanical Engineering · doi:10.65521/ijtarme.v4i1.4382
Metadata
- Authors
- Neseli, S.
- Affiliations
- Department of Mechanical Engineering, Faculty of Technology, Selçuk University, 42075 Konya, Turkey
- Venue
- Advances in Mechanical Engineering
- Publisher
- SAGE Publications
- Published
- 2014-01-01
- Volume
- 6
- Pages
- 925382
- ISSN
- 1687-8132 (ISSN-L)
- 1687-8140
- OpenAlex
- W2020830032
- Cited by
- 30
- References
- 25
- Citations by year
- 2026: 1 · 2025: 5 · 2024: 1 · 2023: 2 · 2022: 4 · 2021: 8 · 2020: 4 · 2019: 2 · 2018: 3
- FWCI
- 0.00
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- cc-by
- journals.sagepub.com/page/policies/text-and-data-mining-license (tdm)
- Locations
- Advances in Mechanical Engineering (publishedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Advanced machining processes and optimization
- Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Advanced Machining and Optimization Techniques
- Social Sciences › Decision Sciences › Management Science and Operations Research › Optimal Experimental Design Methods
- Keywords
- drilling, AISI 1040 steel, thrust, torque, cutting parameters, cutting speed, feed rate, helix angle, Taguchi method, orthogonal arrays, signal-to-noise ratio, process parameter optimization
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.