Optimization of Process Parameters with Minimum Thrust Force and Torque in Drilling Operation Using Taguchi Method
Open accessThe DOI matches its Crossref record; 25 of the 25 references it cites were found in a registry or an index.
Abstract
This research outlines the Taguchi optimization methodology, which is applied to optimize cutting parameters in drilling of AISI 1040 steel. The drilling parameters evaluated are cutting speed, feed rate, and helix angle. Series of experiments are conducted to relate the cutting parameters on the thrust force and torque. L 27 (3 13 ) orthogonal array, signal-to-noise ratio is employed to analyze the influence of these parameters on thrust force and torque during drilling. Analysis of variance (ANOVA) is used to study the effect of process parameters on machining process. The study shows that the Taguchi method is suitable to solve the stated problem with the minimum number of trials. The main objective is to find the important factors and combination of factors that influence the machining process to achieve low thrust force and torque. The analysis of the Taguchi method indicates that the feed rate is the most significant factor affecting the thrust force, while the cutting speed contributes the most to the torque.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Citations
Cites
Application of Taguchi method in the optimization of end milling parameters
Ghani, J. A., Choudhury, I. A., & Hassan, H. H. (2004) · Journal of Materials Processing Technology · doi:10.1016/s0924-0136(03)00865-3 · Cited by 766
Noordin, M. Y., Venkatesh, V. C., Sharif, S., Elting, S., & Abdullah, A. (2004) · Journal of Materials Processing Technology · doi:10.1016/s0924-0136(03)00861-6 · Cited by 739
Delamination During Drilling in Composite Laminates
Ho-Cheng, H., & Dharan, C. K. H. (1990) · Journal of Engineering for Industry · doi:10.1115/1.2899580 · Cited by 572
Delamination in drilling GFR-thermoset composites
Khashaba, U. A. (2004) · Composite Structures · doi:10.1016/s0263-8223(03)00180-6 · Cited by 344
Tsao, C. C., & Hocheng, H. (2008) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2006.04.126 · Cited by 281
Experimental investigation and optimisation in drilling of GFRP composites
Palanikumar, K. (2011) · Measurement · doi:10.1016/j.measurement.2011.07.023 · Cited by 275
Mohan, N. S., Ramachandra, A., & Kulkarni, S. M. (2005) · Composite Structures · doi:10.1016/j.compstruct.2005.09.039 · Cited by 201
Pawade, R. S., & Joshi, S. S. (2011) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-011-3183-z · Cited by 199
Kurt, M., Bagci, E., & Kaynak, Y. (2009) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-007-1368-2 · Cited by 198
Elsayed, K., & Lacor, C. (2011) · Powder Technology · doi:10.1016/j.powtec.2011.10.015 · Cited by 155
Optimization of counter flow Ranque–Hilsch vortex tube performance using Taguchi method
Pınar, A. M., Uluer, O., & Kırmacı, V. (2009) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2009.02.018 · Cited by 154
Sahoo, P. K. (2008) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2008.06.031 · Cited by 140
An analytical finite element technique for predicting thrust force and torque in drilling
Strenkowski, J. S., Hsieh, C.-T., & Shih, A. J. (2004) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2004.01.005 · Cited by 138
Tsao, C. C., & Chiu, Y.-H. (2011) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2011.05.004 · Cited by 132
Drilling analysis of chopped composites
Khashaba, U. A., Seif, M., & Elhamid, M. A. (2006) · Composites Part A Applied Science and Manufacturing · doi:10.1016/j.compositesa.2006.01.020 · Cited by 125
Gfrerer, M. H., & Lankmayr, E. P. (2004) · Analytica Chimica Acta · doi:10.1016/j.aca.2004.11.016 · Cited by 124
Evaluation of Delamination in Drilling GFRP Composites
Palanikumar, K., Prakash, S., & Shanmugam, K. (2008) · Materials and Manufacturing Processes · doi:10.1080/10426910802385026 · Cited by 124
Kıvak, T., Samtaş, G., & Çiçek, A. (2012) · Measurement · doi:10.1016/j.measurement.2012.02.022 · Cited by 116
Measurement and analysis of thrust force in drilling of particle board (PB) composite panels
Valarmathi, T. N., Palanikumar, K., & Latha, B. (2012) · Measurement · doi:10.1016/j.measurement.2012.11.024 · Cited by 73
Surface roughness prediction of flow-formed AA6061 alloy by design of experiments
Davidson, M. J., Balasubramanian, K., & Tagore, G. R. N. (2007) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2007.08.065 · Cited by 64
Yusoff, N., Ramasamy, M., & Yusup, S. B. (2010) · Process Safety and Environmental Protection · doi:10.1016/j.cherd.2010.09.021 · Cited by 61
Machinability of Fiber-Reinforced Thermoplastics in Drilling
Hocheng, H., & Puw, H. Y. (1993) · Journal of Engineering Materials and Technology · doi:10.1115/1.2902148 · Cited by 34
Multi-response optimization of electro-chemical honing using utility-based Taguchi approach
Dubey, A. K. (2008) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-008-1525-2 · Cited by 32
CAD-based simulations and design of experiments for determining thrust force in drilling operations
Kyratsis, P., Bilalis, N., & Antoniadis, A. (2011) · Computer-Aided Design · doi:10.1016/j.cad.2011.06.002 · Cited by 29
Modelling of Thrust Force during Drilling of Fibre Reinforced Plastic Composites
Singh, A. P., & Sharma, M. (2013) · Procedia Engineering · doi:10.1016/j.proeng.2013.01.089 · Cited by 19
Research works printed but not linked: 1
- Roy R. K., 1990, A Primer of Taguchi Method
Cited by
A review: drilling performance and hole quality of aluminium alloys for aerospace applications
Aamir, M., Giasin, K., Tolouei-Rad, M., & Vafadar, A. (2020) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2020.09.003 · Cited by 286
Aamir, M., Tu, S., Tolouei-Rad, M., Giasin, K., & Vafadar, A. (2020) · Materials · doi:10.3390/ma13030680 · Cited by 86
“Conventional drilling is considered to be the most economical and efficient machining processes in the aerospace and automotive industries [1].”
BackgroundAamir, M., Tolouei‐Rad, M., Giasin, K., & Vafadar, A. (2020) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-020-06151-7 · Cited by 37
Huang, W., Tasi, Z.-Y., Ho, W., & Chou, J. (2022) · Polymers · doi:10.3390/polym14030644 · Cited by 29
Aamir, M., Tolouei‐Rad, M., & Giasin, K. (2021) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-021-07082-7 · Cited by 19
Metadata
- Authors
- Neseli, S.
- Affiliations
- Department of Mechanical Engineering, Faculty of Technology, Selçuk University, 42075 Konya, Turkey
- Venue
- Advances in Mechanical Engineering
- Publisher
- SAGE Publications
- Published
- 2014-01-01
- Volume
- 6
- Pages
- 925382
- ISSN
- 1687-8132 (ISSN-L)
- 1687-8140
- OpenAlex
- W2020830032
- Cited by
- 30
- References
- 25
- Citations by year
- 2026: 1 · 2025: 5 · 2024: 1 · 2023: 2 · 2022: 4 · 2021: 8 · 2020: 4 · 2019: 2 · 2018: 3
- FWCI
- 0.00
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- cc-by
- journals.sagepub.com/page/policies/text-and-data-mining-license (tdm)
- Locations
- Advances in Mechanical Engineering (publishedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Advanced machining processes and optimization
- Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Advanced Machining and Optimization Techniques
- Social Sciences › Decision Sciences › Management Science and Operations Research › Optimal Experimental Design Methods
- Keywords
- drilling, AISI 1040 steel, thrust, torque, cutting parameters, cutting speed, feed rate, helix angle, Taguchi method, orthogonal arrays, signal-to-noise ratio, process parameter optimization
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.