Combined effects of various materials on tool wear in drilling of Ti/CFRP stacks
The DOI matches its Crossref record; 19 of the 19 references it cites were found in a registry or an index.
Abstract
Ti/CFRP stacks present the key function in the aviation field due to their excellent properties. However, both titanium alloy and CFRP are hard-to-cut materials and their requirements on cutting tool performance are significantly different. When drilling Ti/CFRP stacks using a compromised tool, tool wear is affected by two materials, resulting in extremely low tool life. This paper investigates the wear process of chisel edge and main cutting edge of carbide step drill bits in the drilling of Ti/CFRP stacks, titanium alloys and CFRP, and the combined effects of various materials on the tool wear are revealed. Based on the wear analysis, it is found that tool wear is more affected by the carbon fiber/Ti-adhesion interaction which makes the rake face more susceptible to occur adhesive wear and slows down the flank wear, and severe rake wear and flank wear have a sharpening effect on cutting edge. It also reveals the relationship between thrust force and tool wear, and results indicate that the variation of thrust force is related to the flank wear and the Ti-adhesion attached to chisel edge, but not to the edge rounding. The conclusions reported in this paper can provide guidance for structural optimization of long-life stacks cutting tools.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“It was followed by the interaction of cutting speed-feed rate, feed rate, and cutting tool geometry with contribution rates of 21.11%, 19.77%, and 16.28% in terms of % effect (Table 5. b) [41].”
From Evaluation and multi-criteria optimization of surface roughness, deviation from dimensional accuracy and roundness error in drilling CFRP/Ti6Al4 stacks (2022) · cites this paper as [41]
In the citing paper
“The feed rate was followed by the cutting speed and the cutting speed-feed rate interaction with 25.97% and 15.94% contribution rates, respectively (Table 5. a) [41].”
From Evaluation and multi-criteria optimization of surface roughness, deviation from dimensional accuracy and roundness error in drilling CFRP/Ti6Al4 stacks (2022) · cites this paper as [41]
Citations
Cites
Cutting edge rounding: An innovative tool wear criterion in drilling CFRP composite laminates
Faraz, A., Biermann, D., & Weinert, K. (2009) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2009.08.002 · Cited by 543 · cited 2×
“Ali et al.(14) quantify the sharpness of the cutting edge and propose cutting edge rounding (CER) to evaluate the wear of the CFRP cutting tool.”
MethodA study on the drilling of composite and titanium stacks
Ramulu, M., Branson, T., & Kim, D. (2001) · Composite Structures · doi:10.1016/s0263-8223(01)00071-x · Cited by 318
Rawat, S., & Attia, H. (2009) · Wear · doi:10.1016/j.wear.2009.01.031 · Cited by 270
Novel drill structure for damage reduction in drilling CFRP composites
Jia, Z., Fu, R., Niu, B., Qian, B., Bai, Y., & Wang, F. (2016) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2016.08.006 · Cited by 247
Self-citationTool wear of coated drills in drilling CFRP
Wang, X., Kwon, P. Y., Sturtevant, C., Kim, D. (.-W., & Lantrip, J. (2013) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2012.09.019 · Cited by 231 · cited 1×
“In terms of tool wear evaluation, the rake wear of the CFRP cutting tool starts directly from the cutting edge which is different from the crater wear of the metal cutting tool.(11,12) Thus Montoya et al.”
MethodPerformance of coated- and uncoated-carbide tools when drilling titanium alloy—Ti–6Al4V
Sharif, S., & Rahim, E. A. (2007) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2006.03.142 · Cited by 201 · cited 1×
“However, titanium alloys are still irreplaceable in some critical load-bearing locations, thus Ti/CFRP stacks structures are formed.(4,5) Since stacks components are usually joined by bolted or riveted, a large number of holes need to be machined on Ti/CFRP stacks, and the quality of the connecting holes will directly…”
BackgroundComparative tool wear study based on drilling experiments on CFRp/Ti stack and its individual layers
Wang, X., Kwon, P. Y., Sturtevant, C., Kim, D., & Lantrip, J. (2014) · Wear · doi:10.1016/j.wear.2014.05.007 · Cited by 136 · cited 3×
“Refer to the method in Wang et al.11 to fit and calculate the CER and flank wear width.”
BackgroundMECHANICAL DRILLING PROCESSES FOR TITANIUM ALLOYS: A LITERATURE REVIEW
Zhang, P. F., Churi, N. J., Pei, Z. J., & Treadwell, C. (2008) · Machining Science and Technology · doi:10.1080/10910340802519379 · Cited by 134 · cited 1×
“However, titanium alloys are still irreplaceable in some critical load-bearing locations, thus Ti/CFRP stacks structures are formed.(4,5) Since stacks components are usually joined by bolted or riveted, a large number of holes need to be machined on Ti/CFRP stacks, and the quality of the connecting holes will directly…”
BackgroundTool Wear Analyses in Low Frequency Vibration Assisted Drilling of CFRP/Ti6Al4V Stack Material
Pecat, O., & Brinksmeier, E. (2014) · Procedia CIRP · doi:10.1016/j.procir.2014.03.050 · Cited by 123 · cited 1×
“Since stacks components are usually joined by bolted or riveted, a large number of holes need to be machined on Ti/CFRP stacks, and the quality of the connecting holes will directly affect the safety and reliability of the equipment.(6,7) But due to the fact that these two materials are difficult to machine and have d…”
BackgroundMontoya, M., Calamaz, M., Gehin, D., & Girot, F. A. (2013) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-013-4817-0 · Cited by 118 · cited 3×
“In terms of tool wear evaluation, the rake wear of the CFRP cutting tool starts directly from the cutting edge which is different from the crater wear of the metal cutting tool.11,12 Thus Montoya et al.13 believe that the flank wear measured by microscope will be affected by the rake wear, which cannot accurately refl…”
BackgroundInfluential
Cited by
A critical review addressing conventional twist drilling mechanisms and quality of CFRP/Ti stacks
Xu, J., Kolesnyk, V., Li, C., Lysenko, B., Peterka, J., & Gupta, M. K. (2023) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2023.04.226 · Cited by 51
Kolesnyk, V., Peterka, J., Alekseev, O., Нешта, А., Xu, J., Lysenko, B., Sahul, M., Martinovič, J., & Hrbál, J. (2022) · Materials · doi:10.3390/ma15051940 · Cited by 51
“However, because of the drill bit wear [21,27], the values of the drilling temperature increased in all tests.”
BackgroundA semi-analytical model for predicting tool wear progression in drilling CFRP
Bai, Y., Wang, F., Fu, R., Hao, J., Si, L., Zhang, B., Liu, W., & Davim, J. P. (2021) · Wear · doi:10.1016/j.wear.2021.204119 · Cited by 44
Self-citationBustamante, L., Jeyaprakash, N., & Yang, C. (2020) · Results in Physics · doi:10.1016/j.rinp.2020.103438 · Cited by 40
Cao, S., Li, Y., Zhang, K., Hou, G., Luo, B., Liu, S., Long, T., & Liu, P. (2023) · Composite Structures · doi:10.1016/j.compstruct.2023.117438 · Cited by 39
Ghazali, M. F., Abdullah, M. M. A. B., Rahim, S. Z. A., GONDRO, J., Pietrusiewicz, P., Garus, S., Stachowiak, T., Sandu, A. V., Tahir, M. F. M., Korkmaz, M. E., et al. (2021) · Materials · doi:10.3390/ma14071628 · Cited by 26
Yıldız, T., & Sur, G. (2021) · Proceedings of the Institution of Mechanical Engineers Part B Journal of Engineering Manufacture · doi:10.1177/0954405421995657 · Cited by 17
“Previous studies proved that the increase in cutting force increases the machining temperature, which increases the tendency of the workpiece material to stick to the tool.(34,47,48) Figure 10.”
BackgroundZhou, Z., Feng, Y., Xu, W., Zhou, H., Qin, Y., & Jia, X. (2022) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-022-10409-7 · Cited by 13
“CFRP/Ti stacks are usually riveted or bolted in aircraft assembly, which requires many high-precision connection holes [4, 5].”
BackgroundMotorcu, A., & Ekici, E. (2022) · FME Transactions · doi:10.5937/fme2203441m · Cited by 12
Establishment of instantaneous milling force prediction model for multi-directional CFRP laminate
Ning, H., Zheng, H., & Yuan, X. (2021) · Advances in Mechanical Engineering · doi:10.1177/16878140211027706 · Cited by 12
“(2) According to formula (3), the instantaneous cutting forces Fx and Fy are converted into instantaneous radial force Fr and instantaneous tangential force Ft, as shown in Figure 8.”
BackgroundMethodKhanna, N., Prajapati, R., & Bolar, G. (2024) · Machining Science and Technology · doi:10.1080/10910344.2024.2369856 · Cited by 9
“It is caused by many individuals and combinations of those individuals wearing mechanisms such as chipping, attrition, adhesion, abrasion, etc (Wang et al., 2020).”
InfluentialChen, Y., Wu, Y., Cheng, M., Zhu, J., Meng, Y., & Mu, X. (2023) · Proceedings of the Institution of Mechanical Engineers Part L Journal of Materials Design and Applications · doi:10.1177/14644207231176745 · Cited by 9
Chen, Y., Wu, Y., Cheng, M., Lai, D., Zhu, J., & Meng, Y. (2023) · Proceedings of the Institution of Mechanical Engineers Part L Journal of Materials Design and Applications · doi:10.1177/14644207231177000 · Cited by 3
“13,14 Bilal et al. proposed a temperature fi eld experimentally simulated model with a random distribution of discharge positions.”
MethodКолесник, В. О., Божко, А. В., Нешта, А. О., & Малимоненко, Д. Г. (2022) · Наукові нотатки · doi:10.36910/775.24153966.2022.73.26
Kolesnyk, V., Lysenko, B., Basov, V. V., Довгополов, А. Ю., Nekrasov, Y. O., Panchenko, A., & Yarosh, V. Y. (2023) · Visnyk of Vinnytsia Politechnical Institute · doi:10.31649/1997-9266-2023-170-5-74-84
Sustainable machining of carbon fiber and Ti6Al4V stacks with assistence of liquified CO2
RODRIGUEZ, I. (2024) · Repository of the University of Ljubljana (University of Ljubljana)
Metadata
- Authors
- Wang, Q., Wang, F., Zhang, C., & Chen, C.
- Affiliations
- Dalian University of Technology (CN)
- Corresponding author
- Wang, Fuji
- Venue
- Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Publisher
- SAGE Publications
- Published
- 2019-08-12
- Volume
- 234
- Issue
- 14
- Pages
- 2750-2759
- ISSN
- 0263-7154 (ISSN-L)
- 0954-4062
- 2041-2983
- OpenAlex
- W2967171482
- Cited by
- 15
- References
- 19
- Citations by year
- 2024: 1 · 2023: 5 · 2022: 4 · 2021: 4 · 2020: 1
- FWCI
- 1.27
- Type
- journal article
- Language
- en
- Open access
- closed
- Licence
- journals.sagepub.com/page/policies/text-and-data-mining-license (tdm)
- Locations
- Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science (publishedVersion)
- Funders
- National Innovative Research Group (No. 51621064)
- National Natural Science Foundation of China (No.51575082)
- National Natural Science Foundation of China-United with Liaoning Province (No. U1508207)
- National Key Basic Research Program of China (No. 2014CB046503)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Advanced machining processes and optimization
- Physical Sciences › Materials Science › Metals and Alloys › Metal Alloys Wear and Properties
- Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Engineering Technology and Methodologies
- Keywords
- tool wear, drilling, titanium alloys, carbon fiber reinforced polymer, chisel edge, adhesive wear, flank wear, rake face wear, thrust, cutting edge rounding
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.