The present and future of additive manufacturing in the aerospace sector: A review of important aspects
Open accessThe DOI matches its Crossref record; 75 of the 79 references it cites were found in a registry or an index.
Abstract
This paper reviews recent improvements in additive manufacturing technologies, focusing on those which have the potential to produce and repair metal parts for the aerospace industry. Electron beam melting, selective laser melting and other metal deposition processes, such as wire and arc additive manufacturing, are presently regarded as the best candidates to achieve this challenge. For this purpose, it is crucial that these technologies are well characterised and modelled to predict the resultant microstructure and mechanical properties of the part. This paper presents the state of the art in additive manufacturing and material modelling. While these processes present many advantages to the aerospace industry in comparison with traditional manufacturing processes, airworthiness and air transport safety must be guaranteed. The impact of this regulatory framework on the implementation of additive manufacturing for repair and production of parts for the aerospace industry is presented.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“The existing AM fatigue literature demonstrates test results that indicate porosity, residual stress and surface roughness are the largest concerns for high cycle fatigue (HCF) and low cycle fatigue (LCF) testing scenarios with overall fatigue properties generally substandard compared to conventional manufacturing processes [34,40,41].”
From Metal additive manufacturing in aerospace: A review (2021) · cites this paper as [40]
In the citing paper
“However, dynamic mechanical properties such as fatigue and creep have seen relatively less research and there remains a lack of test data reporting among aerospace companies [40].”
From Metal additive manufacturing in aerospace: A review (2021) · cites this paper as [40]
Citations
Cites
Metal Additive Manufacturing: A Review
Frazier, W. E. (2014) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-014-0958-z · Cited by 5,984 · cited 4×
“Normally, the building direction (Z-direction)(66) is the weakest in terms of the ultimate tensile stress.(62) Ti6Al4V is the most widely alloy used in AM technologies.”
BackgroundInfluentialLaser additive manufacturing of metallic components: materials, processes and mechanisms
Gu, D. D., Meiners, W., Wissenbach, K., & Poprawe, R. (2012) · International Materials Reviews · doi:10.1179/1743280411y.0000000014 · Cited by 3,197
Additive Manufacturing Technologies: Rapid Prototyping to Direct Digital Manufacturing
Gibson, I., Rosen, D. W., & Stucker, B. (2010) · National University of Singapore · doi:10.1007/978-1-4419-1120-9 · Cited by 2,969
A study of the microstructural evolution during selective laser melting of Ti–6Al–4V
Thijs, L., Verhaeghe, F., Craeghs, T., Humbeeck, J. V., & Kruth, J.-P. (2010) · Acta Materialia · doi:10.1016/j.actamat.2010.02.004 · Cited by 2,929
Residual stresses in selective laser sintering and selective laser melting
Mercelis, P., & Kruth, J. (2006) · Rapid Prototyping Journal · doi:10.1108/13552540610707013 · Cited by 2,015
Metal Fabrication by Additive Manufacturing Using Laser and Electron Beam Melting Technologies
Murr, L. E., Gaytan, S. M., Ramirez, D. A., Martinez, E., Hernandez, J., Amato, K. N., Shindo, P. W., Medina, F. R., & Wicker, R. B. (2012) · Journal of Materials Science & Technology · doi:10.1016/s1005-0302(12)60016-4 · Cited by 1,686
Steen, W. M. (1998) · Springer eBooks · doi:10.1007/978-1-4471-3609-5 · Cited by 1,547
Levy, G. N., Schindel, R., & Kruth, J. P. (2003) · CIRP Annals · doi:10.1016/s0007-8506(07)60206-6 · Cited by 1,121
An introduction to phase-field modeling of microstructure evolution
Moelans, N., Blanpain, B., & Wollants, P. (2008) · Calphad · doi:10.1016/j.calphad.2007.11.003 · Cited by 1,006
Murr, L. E., Quinones, S. A., Gaytan, S. M., Lopez, M. I., Rodela, A., Martinez, E. Y., Hernandez, D. H., Martinez, E., Medina, F., & Wicker, R. B. (2009) · Journal of the Mechanical Behavior of Biomedical Materials · doi:10.1016/j.jmbbm.2008.05.004 · Cited by 997
Research works printed but not linked: 14
- Lyons B, 2012, The Bridge, 42, 13
- Rudgley M. Rapid manufacturing—the revolution is beginning. In: Proceeedings of the uRapid 2001, Amsterdam, Netherlands, May 2001, pp.441–444.
- Bontha S, 2009, Mater Sci Eng A, 513
- Wood D, 2009, TCT Magazine, 17, 23
- White D, 2003, Ultrasonic object consolidation
- Santamaría de las Cuevas F, San José Santamaría I. La tecnología de haz de electrones y sus aplicaciones, Madrid: McGraw-Hill, 1993, pp. 159–159.
- Rios Contesse SE, Williams S and Wang F. Plasma torch design for wire and arc additive manufacturing (WAAM) titanium alloy . MSc Thesis, Cranfield University, School of Applied Sciences, Bedfordshire, UK, 2013.
- Mudge RP, 2007, Weld J (Miami Fla), 86, 44
- Brodin H, Andersson O and Johansson S. Mechanical testing of a selective laser melted superalloy. In: 13th international conference on fracture , Beijin, China, June 2013, pp.1-11. Sweden.
- Greitemeir D, Schmidtke K, Holzinger V, et al. Additive layer manufacturing of Ti-6Al-4 V and scalmalloyrp fatigue and fracture. In: 1st international conference of the international journal of structural integrity (ed Sérgio M.O. Tavares), Faculty of Engineering, University of Oporto, June, pp.11. Portugal: Publindústria.
- Nguyen NT, 1999, Weld J, 265
- Rosenthal D, 1946, Trans ASME, 68, 849
- Attar E. Simulation der selektiven Elektronenstrahlschmelzprozesse . PhD Thesis, Der Technischen Fakultät der Universität Erlangen-Nürnberg, 2011.
- Maher M. Brief presented at the SAMPLE direct part manufacturing workshop, 2012.
Cited by
Metal additive manufacturing in aerospace: A review
Blakey-Milner, B., Gradl, P., Snedden, G., Brooks, M., Pitot, J., Lopez, E., Leary, M., Berto, F., & du Plessis, A. (2021) · Materials & Design · doi:10.1016/j.matdes.2021.110008 · Cited by 2,263
An Overview on 3D Printing Technology: Technological, Materials, and Applications
Shahrubudin, N., Lee, T. C., & Ramlan, R. (2019) · Procedia Manufacturing · doi:10.1016/j.promfg.2019.06.089 · Cited by 2,050
Wu, B., Pan, Z., Ding, D., Cuiuri, D., Li, H., Xu, J., & Norrish, J. (2018) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2018.08.001 · Cited by 1,577
Review of in-situ process monitoring and in-situ metrology for metal additive manufacturing
Everton, S. K., Hirsch, M., Stravroulakis, P., Leach, R. K., & Clare, A. T. (2016) · Materials & Design · doi:10.1016/j.matdes.2016.01.099 · Cited by 1,469
“In addition, key reviews have been published in the area of applications and opportunities for AM techniques; these have centred around biomedical [6,7] aerospace [8], tooling [9] and general manufacturing [10].”
BackgroundReview of additive manufacturing technologies and applications in the aerospace industry
Najmon, J. C., Raeisi, S., & Tovar, A. (2019) · Additive Manufacturing for the Aerospace Industry · doi:10.1016/b978-0-12-814062-8.00002-9 · Cited by 719
Metadata
- Authors
- Uriondo, A., Esperon-Miguez, M., & Perinpanayagam, S.
- Affiliations
- Cranfield University (GB)
- Corresponding author
- Uriondo, Adrián
- Venue
- Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
- Publisher
- SAGE Publications
- Published
- 2015-01-28
- Volume
- 229
- Issue
- 11
- Pages
- 2132-2147
- ISSN
- 0954-4100 (ISSN-L)
- 2041-3025
- OpenAlex
- W2132660986
- Cited by
- 489
- References
- 79
- Citations by year
- 2026: 23 · 2025: 46 · 2024: 64 · 2023: 61 · 2022: 66 · 2021: 65 · 2020: 47 · 2019: 58 · 2018: 29 · 2017: 19 · 2016: 9 · 2015: 2
- FWCI
- 19.32
- Type
- journal article
- Language
- en
- Open access
- Licence
- cc-by-nc
- journals.sagepub.com/page/policies/text-and-data-mining-license (tdm)
- Locations
- Proceedings of the Institution of Mechanical Engineers Part G Journal of Aerospace Engineering (publishedVersion)
- CERES (Cranfield University) (submittedVersion, cc-by-nc)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Additive Manufacturing Materials and Processes
- Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Additive Manufacturing and 3D Printing Technologies
- Physical Sciences › Engineering › Mechanical Engineering › High Temperature Alloys and Creep
- Keywords
- additive manufacturing, aerospace industry, electron beam melting, laser powder bed fusion, wire arc additive manufacturing, microstructure prediction, mechanical properties, material modeling, airworthiness, regulatory framework, part production
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: The present and future of additive manufacturing in the aerospace sector: A review of important aspects. https://app.cochat.ai/papers/10.1177/0954410014568797
- The paper
- Uriondo, A., Esperon-Miguez, M., & Perinpanayagam, S. (2015). The present and future of additive manufacturing in the aerospace sector: A review of important aspects. Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering. https://doi.org/10.1177/0954410014568797
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.