The present and future of additive manufacturing in the aerospace sector: A review of important aspects
Open accessThe DOI matches its Crossref record; 75 of the 79 references it cites were found in a registry or an index.
Abstract
This paper reviews recent improvements in additive manufacturing technologies, focusing on those which have the potential to produce and repair metal parts for the aerospace industry. Electron beam melting, selective laser melting and other metal deposition processes, such as wire and arc additive manufacturing, are presently regarded as the best candidates to achieve this challenge. For this purpose, it is crucial that these technologies are well characterised and modelled to predict the resultant microstructure and mechanical properties of the part. This paper presents the state of the art in additive manufacturing and material modelling. While these processes present many advantages to the aerospace industry in comparison with traditional manufacturing processes, airworthiness and air transport safety must be guaranteed. The impact of this regulatory framework on the implementation of additive manufacturing for repair and production of parts for the aerospace industry is presented.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“The existing AM fatigue literature demonstrates test results that indicate porosity, residual stress and surface roughness are the largest concerns for high cycle fatigue (HCF) and low cycle fatigue (LCF) testing scenarios with overall fatigue properties generally substandard compared to conventional manufacturing processes [34,40,41].”
From Metal additive manufacturing in aerospace: A review (2021) · cites this paper as [40]
In the citing paper
“However, dynamic mechanical properties such as fatigue and creep have seen relatively less research and there remains a lack of test data reporting among aerospace companies [40].”
From Metal additive manufacturing in aerospace: A review (2021) · cites this paper as [40]
Citations
Cites
Metal Additive Manufacturing: A Review
Frazier, W. E. (2014) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-014-0958-z · Cited by 5,984 · cited 4×
“Normally, the building direction (Z-direction)(66) is the weakest in terms of the ultimate tensile stress.(62) Ti6Al4V is the most widely alloy used in AM technologies.”
BackgroundInfluentialLaser additive manufacturing of metallic components: materials, processes and mechanisms
Gu, D. D., Meiners, W., Wissenbach, K., & Poprawe, R. (2012) · International Materials Reviews · doi:10.1179/1743280411y.0000000014 · Cited by 3,197
Additive Manufacturing Technologies: Rapid Prototyping to Direct Digital Manufacturing
Gibson, I., Rosen, D. W., & Stucker, B. (2010) · National University of Singapore · doi:10.1007/978-1-4419-1120-9 · Cited by 2,969
A study of the microstructural evolution during selective laser melting of Ti–6Al–4V
Thijs, L., Verhaeghe, F., Craeghs, T., Humbeeck, J. V., & Kruth, J.-P. (2010) · Acta Materialia · doi:10.1016/j.actamat.2010.02.004 · Cited by 2,929
Residual stresses in selective laser sintering and selective laser melting
Mercelis, P., & Kruth, J. (2006) · Rapid Prototyping Journal · doi:10.1108/13552540610707013 · Cited by 2,015
Metal Fabrication by Additive Manufacturing Using Laser and Electron Beam Melting Technologies
Murr, L. E., Gaytan, S. M., Ramirez, D. A., Martinez, E., Hernandez, J., Amato, K. N., Shindo, P. W., Medina, F. R., & Wicker, R. B. (2012) · Journal of Materials Science & Technology · doi:10.1016/s1005-0302(12)60016-4 · Cited by 1,686
Steen, W. M. (1998) · Springer eBooks · doi:10.1007/978-1-4471-3609-5 · Cited by 1,547
Levy, G. N., Schindel, R., & Kruth, J. P. (2003) · CIRP Annals · doi:10.1016/s0007-8506(07)60206-6 · Cited by 1,121
An introduction to phase-field modeling of microstructure evolution
Moelans, N., Blanpain, B., & Wollants, P. (2008) · Calphad · doi:10.1016/j.calphad.2007.11.003 · Cited by 1,006
Murr, L. E., Quinones, S. A., Gaytan, S. M., Lopez, M. I., Rodela, A., Martinez, E. Y., Hernandez, D. H., Martinez, E., Medina, F., & Wicker, R. B. (2009) · Journal of the Mechanical Behavior of Biomedical Materials · doi:10.1016/j.jmbbm.2008.05.004 · Cited by 997
Steen, W. M., & Mazumder, J. (2010) · Springer eBooks · doi:10.1007/978-1-84996-062-5 · Cited by 907
Rapid Prototyping, Principles and Applications
(2010) · Assembly Automation · doi:10.1108/aa.2010.03330dae.001 · Cited by 692
Ding, J., Colegrove, P., Mehnen, J., Ganguly, S., Sequeira Almeida, P. M., Wang, F., & Williams, S. (2011) · Computational Materials Science · doi:10.1016/j.commatsci.2011.06.023 · Cited by 689
Residual Stress within Metallic Model Made by Selective Laser Melting Process
Shiomi, M., Osakada, K., Nakamura, K., Yamashita, T., & Abe, F. (2004) · CIRP Annals · doi:10.1016/s0007-8506(07)60677-5 · Cited by 591
Murr, L. E., Esquivel, E. V., Quinones, S. A., Gaytan, S. M., Lopez, M. I., Martinez, E. Y., Medina, F., Hernandez, D. H., Martinez, E., Martinez, J. L., et al. (2009) · Materials Characterization · doi:10.1016/j.matchar.2008.07.006 · Cited by 564 · cited 1×
“As a result, the microstructure of the part changes significantly from EBM to SLM and thus, the mechanical properties will be different.(13,41,42)”
BackgroundVrancken, B., Thijs, L., Kruth, J.-P., & Van Humbeeck, J. (2014) · Acta Materialia · doi:10.1016/j.actamat.2014.01.018 · Cited by 553
Modeling metal deposition in heat transfer analyses of additive manufacturing processes
Michaleris, P. (2014) · Finite Elements in Analysis and Design · doi:10.1016/j.finel.2014.04.003 · Cited by 527
Murr, L. E., Gaytan, S. M., Ceylan, A., Martinez, E., Martinez, J. L., Hernandez, D. H., Machado, B. I., Ramirez, D. A., Medina, F., Collins, S., et al. (2010) · Acta Materialia · doi:10.1016/j.actamat.2009.11.032 · Cited by 526 · cited 4×
“The analysis of transmission electron microscopy images from the studies of Murr et al.40,52 show high dislocation density inside a-phase grains in EBM processes and deformation twins in a-phase in the martensitic structure (see Figure 3).”
MethodInfluentialDuctility of a Ti‐6Al‐4V alloy produced by selective laser melting of prealloyed powders
Facchini, L., Magalini, E., Robotti, P., Molinari, A., Höges, S., & Wissenbach, K. (2010) · Rapid Prototyping Journal · doi:10.1108/13552541011083371 · Cited by 512 · cited 2×
“Facchini et al.(54,55) have studied how to modify the mechanical properties of Ti6Al4V AM parts with heat treatments.”
BackgroundClosed loop direct metal deposition: art to part
Mazumder, J., Dutta, D., Kikuchi, N., & Ghosh, A. (2000) · Optics and Lasers in Engineering · doi:10.1016/s0143-8166(00)00072-5 · Cited by 452 · cited 2×
“Surface roughness depends on the technology, the scan strategy, the position of the part on the build platform, and some other process parameters, like the hatch space or the scan velocity.26,62 Mazumder et al.65 showed that for laser cladding, a type of MD process, the largest roughness can be measured perpendicular…”
BackgroundMesoscopic simulation of selective beam melting processes
Körner, C., Attar, E., & Heinl, P. (2011) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2010.12.016 · Cited by 450 · cited 2×
“Körner et al.83 developed a 2D-LBM model to study the influence of melting and solidification of a randomly packed powder bed under a Gaussian beam.”
MethodRapid manufacturing in the spare parts supply chain: Alternative approaches to capacity deployment
Holmström, J., Partanen, J., Tuomi, J., & Walter, M. (2010) · Journal of Manufacturing Technology Management · doi:10.1108/17410381011063996 · Cited by 431
Microstructural evolution of a Ti–6Al–4V alloy during thermomechanical processing
Ding, R., Guo, Z. X., & Wilson, A. (2002) · Materials Science and Engineering: A · doi:10.1016/s0921-5093(01)01531-3 · Cited by 413
Gandin, C. A., Desbiolles, J. L., Rappaz, M., & Thevoz, P. (1999) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-999-0226-2 · Cited by 360
Surface Morphology in Selective Laser Melting of Metal Powders
Yadroitsev, I., & Smurov, I. (2011) · Physics Procedia · doi:10.1016/j.phpro.2011.03.034 · Cited by 349 · cited 1×
“2015–5:21pm] [1–16] //blrnas3.”
Rapid Prototyping: Principles and Applications (with Companion CD-ROM)
Chua, C. K., Leong, K. F., & Lim, C. S. (2010) · WORLD SCIENTIFIC eBooks · doi:10.1142/6665 · Cited by 346
Analytical and numerical modelling of the direct metal deposition laser process
Peyre, P., Aubry, P., Fabbro, R., Neveu, R., & Longuet, A. (2008) · Journal of Physics D: Applied Physics · doi:10.1088/0022-3727/41/2/025403 · Cited by 323 · cited 1×
“The energy inside the pool is enough to melt the incoming powder.(78)”
BackgroundChan, K. S., Koike, M., Mason, R. L., & Okabe, T. (2013) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-012-1470-4 · Cited by 320 · cited 2×
“Chan et al.63 investigated the effect of roughness on fatigue life in Ti6Al4V parts fabricated by EBM (ARCAM A2, ARCAMTM) and SLM (EOSINT M270, EOS GmbH).”
Heat transfer modelling and stability analysis of selective laser melting
Gusarov, A. V., Yadroitsev, I., Bertrand, P., & Smurov, I. (2007) · Applied Surface Science · doi:10.1016/j.apsusc.2007.08.074 · Cited by 314
A pragmatic model for selective laser melting with evaporation
Verhaeghe, F., Craeghs, T., Heulens, J., & Pandelaers, L. (2009) · Acta Materialia · doi:10.1016/j.actamat.2009.08.027 · Cited by 308 · cited 2×
“Verhaeghe et al.(70) developed a model to study the influence of evaporation.”
BackgroundBourell, D. L., Leu, M. C., & Rosen, D. W. (2009) · Cited by 304
Murr, L. E., Martinez, E., Gaytan, S. M., Ramirez, D. A., Machado, B. I., Shindo, P. W., Martinez, J. L., Medina, F., Wooten, J., Ciscel, D., et al. (2011) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-011-0748-2 · Cited by 291
Facchini, L., Magalini, E., Robotti, P., & Molinari, A. (2009) · Rapid Prototyping Journal · doi:10.1108/13552540910960262 · Cited by 290 · cited 2×
“Facchini et al.(54,55) have studied how to modify the mechanical properties of Ti6Al4V AM parts with heat treatments.”
BackgroundNguyen, N. T., Ohta, A., Matsuoka, K., Suzuki, N., & Maeda, Y. (1999) · Welding Journal · Cited by 270
Modelling and simulation of electron beam melting
Zäh, M. F., & Lutzmann, S. (2010) · Production Engineering · doi:10.1007/s11740-009-0197-6 · Cited by 263 · cited 1×
“Laser technology(27,28) has improved in recent years in terms of small focused spots, higher laser power and wavelengths better tuned to the absorptivity of metal powder.(27,29,30) Nowadays, almost all AM laser machines use fibre lasers instead of CO2 lasers or Nd:YAG.”
BackgroundFabrication of geometrical features using wire and arc additive manufacture
Kazanas, P., Deherkar, P., Almeida, P., Lockett, H., & Williams, S. (2012) · Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture · doi:10.1177/0954405412437126 · Cited by 261 · cited 1×
“Most of those technologies use a laser as a heat source, but there are similar processes that use an electron beam or a plasma source instead of a laser beam as a heat source.(15,37,44,45) The deposition head is usually an integrated collection of a heat source, a powder nozzle(s) and inert gas, like in Laser Cladding…”
BackgroundZheng, B., Zhou, Y., Smugeresky, J. E., Schoenung, J. M., & Lavernia, E. J. (2008) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-008-9557-7 · Cited by 245
Gasser, A., Backes, G., Kelbassa, I., Weisheit, A., & Wissenbach, K. (2010) · Laser Technik Journal · doi:10.1002/latj.201090029 · Cited by 223
Ramirez, D. A., Murr, L. E., Martinez, E., Hernandez, D. H., Martinez, J. L., Machado, B. I., Medina, F., Frigola, P., & Wicker, R. B. (2011) · Acta Materialia · doi:10.1016/j.actamat.2011.03.033 · Cited by 217
Zheng, B., Zhou, Y., Smugeresky, J. E., Schoenung, J. M., & Lavernia, E. J. (2008) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-008-9566-6 · Cited by 214 · cited 1×
“The typical microstructure attained is similar to that in the SLM process due to the high cooling rates (from 10(3)C/s to as high as 10(4)C/s).(47,48) Residual stresses are one of the most significant problems in MD processes.”
BackgroundBontha, S., Klingbeil, N. W., Kobryn, P. A., & Fraser, H. L. (2009) · Materials Science and Engineering: A · doi:10.1016/j.msea.2009.02.019 · Cited by 198
Alimardani, M., Toyserkani, E., & Huissoon, J. P. (2007) · Optics and Lasers in Engineering · doi:10.1016/j.optlaseng.2007.06.010 · Cited by 191
Strondl, A., Fischer, R., Frommeyer, G., & Schneider, A. (2008) · Materials Science and Engineering: A · doi:10.1016/j.msea.2007.07.012 · Cited by 187
Evaluation of titanium alloy fabricated using electron beam melting system for dental applications
Koike, M., Martinez, K., Guo, L., Chahine, G., Kovacevic, R., & Okabe, T. (2011) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2011.03.013 · Cited by 182
The role of process variables in laser-based direct metal solid freeform fabrication
Beuth, J., & Klingbeil, N. (2001) · JOM · doi:10.1007/s11837-001-0067-y · Cited by 180 · cited 2×
“Much research related to the analysis of temperature distribution in transient heat conduction for welding(67) have been applied to modelling AM processes.(68) However, none of this research takes into account all physical phenomena of the process, such as non-thermal constant properties, heat of phase transformation,…”
BackgroundModeling of grain refinement in aluminum and copper subjected to cutting
Ding, H., Shen, N., & Shin, Y. C. (2011) · Computational Materials Science · doi:10.1016/j.commatsci.2011.05.020 · Cited by 169
Simulation of Laser Beam Melting of Steel Powders using the Three-Dimensional Volume of Fluid Method
Gürtler, F.-J., Karg, M., Leitz, K.-H., & Schmidt, M. (2013) · Physics Procedia · doi:10.1016/j.phpro.2013.03.162 · Cited by 165 · cited 2×
“Gürtler et al.(72) used the three-dimensional (3D) volume of fluid method to study the effect of the powder-layer thickness, power, scan spacing and scan velocity on the process dynamics.”
MethodMechanical properties of a Ti6Al4V porous structure produced by selective laser melting
Sun, J., Yang, Y., & Wang, D. (2013) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2013.01.038 · Cited by 163 · cited 1×
“2015–5:21pm] [1–16] //blrnas3.”
Microstructures of Rene 142 nickel-based superalloy fabricated by electron beam melting
Murr, L. E., Martinez, E., Pan, X., Gaytan, S. M., de Castro, J. A., Terrazas, C. A., Medina, F. R., Wicker, R. B., & Abbott, D. H. (2013) · Acta Materialia · doi:10.1016/j.actamat.2013.04.002 · Cited by 145
Phase field modeling of microstructure evolution in steels
Militzer, M. (2010) · Current Opinion in Solid State and Materials Science · doi:10.1016/j.cossms.2010.10.001 · Cited by 142
Numerical modeling of the thermal behavior during the LENS® process
Ye, R., Smugeresky, J. E., Zheng, B., Zhou, Y., & Lavernia, E. J. (2006) · Materials Science and Engineering A · doi:10.1016/j.msea.2006.04.079 · Cited by 138
Towards a universal numerical simulation model for laser material processing
Otto, A., & Schmidt, M. (2010) · Physics Procedia · doi:10.1016/j.phpro.2010.08.120 · Cited by 130
Additive Manufacturing in Aerospace; Examples and Research Outlook
Lyons, B. (2014) · The Bridge · Cited by 129
A process planning method for improving build performance in stereolithography
West, A. P., Sambu, S., & Rosen, D. W. (2001) · Computer-Aided Design · doi:10.1016/s0010-4485(00)00064-6 · Cited by 121
Modelling of electron beam absorption in complex geometries
Klassen, A., Bauereiß, A., & Körner, C. (2014) · Journal of Physics D Applied Physics · doi:10.1088/0022-3727/47/6/065307 · Cited by 118 · cited 3×
“Klassen et al.(35) showed the strong influence of the electron beam absorption and the depth of penetration on the quality of the part using a two-dimensional 2D-thermal lattice Boltzmann method (LBM).”
BackgroundMethodNumerical simulation of the electron beam welding process
Lacki, P., & Adamus, K. (2011) · Computers & Structures · doi:10.1016/j.compstruc.2011.01.016 · Cited by 106 · cited 1×
“principles as electron beam welding.(32) This technology is mainly commercialised by Arcam.”
BackgroundProcess control and development in wire and arc additive manufacturing
Almeida, S. (2012) · CERES (Cranfield University) · Cited by 97
Thermo-mechanical analysis of wire and arc additive manufacturing process
Ding, J. (2012) · CERES (Cranfield University) · Cited by 97
Melting of a subcooled mixed powder bed with constant heat flux heating
Zhang, Y., & Faghri, A. (1999) · International Journal of Heat and Mass Transfer · doi:10.1016/s0017-9310(98)00231-2 · Cited by 86 · cited 2×
“Zhang et al.69 show that neglecting melting and re-solidification processes, and therefore the change of density, could result in important errors in the thermal model.”
BackgroundNumerical simulation of laser irradiation to a randomly packed bimodal powder bed
Zhou, J., Zhang, Y., & Chen, J. K. (2009) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2009.01.028 · Cited by 80 · cited 4×
“Whilst in SLM the energy of the photons is absorbed by the powder particles, in EBM the electrons transfer their kinetic energy to the powder particles.(30,35) This means that the powder particles increase their negative charge.”
BackgroundInfluentialWear behaviors of an (TiB+TiC)/Ti composite coating fabricated on Ti6Al4V by laser cladding
Li, J., Yu, Z., & Wang, H.-P. (2011) · Thin Solid Films · doi:10.1016/j.tsf.2011.01.034 · Cited by 77
Additive Manufacturing of Aerospace Alloys for Aircraft Structures
Kobryn, P. A., Ontko, N. R., Perkins, L., & Tiley, J. (2006) · Cited by 69
Laser Cladding of TiC for Better Titanium Components
Sampedro, J., Pérez, I., Carcel, B., Ramos, J. A., & Amigó, V. (2011) · Physics Procedia · doi:10.1016/j.phpro.2011.03.040 · Cited by 59 · cited 1×
“2015–5:21pm] [1–16] //blrnas3.”
Chen, T., & Zhang, Y. (2004) · Numerical Heat Transfer Part A Applications · doi:10.1080/104077890504177 · Cited by 56
A numerical algorithm for the solution of a phase-field model of polycrystalline materials
Dorr, M. R., Fattebert, J., Wickett, M. E., Belak, J. F., & Turchi, P. E. A. (2009) · Journal of Computational Physics · doi:10.1016/j.jcp.2009.09.041 · Cited by 54
Electron beam melting of advanced materials and structures.
Mahale, T. (2011) · Cited by 53
Direct Digital Manufacturing of Metallic Components: Vision and Roadmap
Frazier, W. E. (2010) · doi:10.26153/tsw/15235 · Cited by 46
Gibson, I., Rosen, D. W., & Stucker, B. E. (2009) · Springer eBooks · doi:10.1007/978-1-4419-1120-9_6 · Cited by 43
Xiao, B., & Zhang, Y. (2008) · Journal of Manufacturing Science and Engineering · doi:10.1115/1.2951948 · Cited by 39
Critical Assessment of Temperature Distribution in Submerged Arc Welding Process
Negi, V., & Chattopadhyaya, S. (2013) · Advances in Materials Science and Engineering · doi:10.1155/2013/543594 · Cited by 29
The Coupled CFD-FEM Model of Electron Beam Melting® (EBM)
Jamshidinia, M., Kong, F., & Kovacevic, R. (2013) · Cited by 24
Design for Rapid Manufacturing functional SLS parts
Kruf, W., van de Vorst, B., Maalderink, H., & Kamperman, N. (2006) · Elsevier eBooks · doi:10.1016/b978-008045157-2/50070-5 · Cited by 21
Service experience with single crystal superalloys for high pressure turbine shrouds
Nijdam, T. J., & van Gestel, R. (2011) · Cited by 11
Applications of phase field modeling
Qin, R. S., & Bhadeshia, H. K. D. H. (2011) · Current Opinion in Solid State and Materials Science · doi:10.1016/j.cossms.2011.04.004 · Cited by 7
Processing of pure Ti by rapid prototyping based on laser cladding
Arias-González, F., del Val, J., Comesaña, R., Lusquiños, F., Quintero, F., Riveiro, A., Boutinguiza, M., & Pou, J. (2013) · Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE · doi:10.1117/12.2026114 · Cited by 6
Research works printed but not linked: 14
- Lyons B, 2012, The Bridge, 42, 13
- Rudgley M. Rapid manufacturing—the revolution is beginning. In: Proceeedings of the uRapid 2001, Amsterdam, Netherlands, May 2001, pp.441–444.
- Bontha S, 2009, Mater Sci Eng A, 513
- Wood D, 2009, TCT Magazine, 17, 23
- White D, 2003, Ultrasonic object consolidation
- Santamaría de las Cuevas F, San José Santamaría I. La tecnología de haz de electrones y sus aplicaciones, Madrid: McGraw-Hill, 1993, pp. 159–159.
- Rios Contesse SE, Williams S and Wang F. Plasma torch design for wire and arc additive manufacturing (WAAM) titanium alloy . MSc Thesis, Cranfield University, School of Applied Sciences, Bedfordshire, UK, 2013.
- Mudge RP, 2007, Weld J (Miami Fla), 86, 44
- Brodin H, Andersson O and Johansson S. Mechanical testing of a selective laser melted superalloy. In: 13th international conference on fracture , Beijin, China, June 2013, pp.1-11. Sweden.
- Greitemeir D, Schmidtke K, Holzinger V, et al. Additive layer manufacturing of Ti-6Al-4 V and scalmalloyrp fatigue and fracture. In: 1st international conference of the international journal of structural integrity (ed Sérgio M.O. Tavares), Faculty of Engineering, University of Oporto, June, pp.11. Portugal: Publindústria.
- Nguyen NT, 1999, Weld J, 265
- Rosenthal D, 1946, Trans ASME, 68, 849
- Attar E. Simulation der selektiven Elektronenstrahlschmelzprozesse . PhD Thesis, Der Technischen Fakultät der Universität Erlangen-Nürnberg, 2011.
- Maher M. Brief presented at the SAMPLE direct part manufacturing workshop, 2012.
Cited by
Metal additive manufacturing in aerospace: A review
Blakey-Milner, B., Gradl, P., Snedden, G., Brooks, M., Pitot, J., Lopez, E., Leary, M., Berto, F., & du Plessis, A. (2021) · Materials & Design · doi:10.1016/j.matdes.2021.110008 · Cited by 2,263
An Overview on 3D Printing Technology: Technological, Materials, and Applications
Shahrubudin, N., Lee, T. C., & Ramlan, R. (2019) · Procedia Manufacturing · doi:10.1016/j.promfg.2019.06.089 · Cited by 2,050
Wu, B., Pan, Z., Ding, D., Cuiuri, D., Li, H., Xu, J., & Norrish, J. (2018) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2018.08.001 · Cited by 1,577
Review of in-situ process monitoring and in-situ metrology for metal additive manufacturing
Everton, S. K., Hirsch, M., Stravroulakis, P., Leach, R. K., & Clare, A. T. (2016) · Materials & Design · doi:10.1016/j.matdes.2016.01.099 · Cited by 1,469
“In addition, key reviews have been published in the area of applications and opportunities for AM techniques; these have centred around biomedical [6,7] aerospace [8], tooling [9] and general manufacturing [10].”
BackgroundReview of additive manufacturing technologies and applications in the aerospace industry
Najmon, J. C., Raeisi, S., & Tovar, A. (2019) · Additive Manufacturing for the Aerospace Industry · doi:10.1016/b978-0-12-814062-8.00002-9 · Cited by 719
Metadata
- Authors
- Uriondo, A., Esperon-Miguez, M., & Perinpanayagam, S.
- Affiliations
- Cranfield University (GB)
- Corresponding author
- Uriondo, Adrián
- Venue
- Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
- Publisher
- SAGE Publications
- Published
- 2015-01-28
- Volume
- 229
- Issue
- 11
- Pages
- 2132-2147
- ISSN
- 0954-4100 (ISSN-L)
- 2041-3025
- OpenAlex
- W2132660986
- Cited by
- 489
- References
- 79
- Citations by year
- 2026: 23 · 2025: 46 · 2024: 64 · 2023: 61 · 2022: 66 · 2021: 65 · 2020: 47 · 2019: 58 · 2018: 29 · 2017: 19 · 2016: 9 · 2015: 2
- FWCI
- 19.32
- Type
- journal article
- Language
- en
- Open access
- Licence
- cc-by-nc
- journals.sagepub.com/page/policies/text-and-data-mining-license (tdm)
- Locations
- Proceedings of the Institution of Mechanical Engineers Part G Journal of Aerospace Engineering (publishedVersion)
- CERES (Cranfield University) (submittedVersion, cc-by-nc)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Additive Manufacturing Materials and Processes
- Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Additive Manufacturing and 3D Printing Technologies
- Physical Sciences › Engineering › Mechanical Engineering › High Temperature Alloys and Creep
- Keywords
- additive manufacturing, aerospace industry, electron beam melting, laser powder bed fusion, wire arc additive manufacturing, microstructure prediction, mechanical properties, material modeling, airworthiness, regulatory framework, part production
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.