Force Compensation Control for Electro-Hydraulic Servo System with Pump–Valve Compound Drive via QFT–DTOC
Open accessThe DOI matches its Crossref record; 35 of the 35 references it cites were found in a registry or an index; 5 of the 15 sources its claims cite were checked for support.
Abstract
Each joint of a hydraulic-driven legged robot adopts a highly integrated hydraulic drive unit (HDU), which features a high power–weight ratio. However, most HDUs are throttling-valve-controlled cylinder systems, which exhibit high energy losses. By contrast, pump control systems offer a high efficiency. Nevertheless, their response ability is unsatisfactory. To fully utilize the advantages of pump and valve control systems, in this study, a new type of pump–valve compound drive system (PCDS) is designed, which can not only effectively reduce the energy loss, but can also ensure the response speed and response accuracy of the HDUs in robot joints to satisfy the performance requirements of robots. Herein, considering the force control requirements of energy conservation, high precision, and fast response of the robot joint HDU, a nonlinear mathematical model of the PCDS force control system is first introduced. In addition, pressure–flow nonlinearity, friction nonlinearity, load complexity and variability, and other factors affecting the system are considered, and a novel force control method based on quantitative feedback theory (QFT) and a disturbance torque observer (DTO) is designed, which is denoted as QFT–DTOC herein. This method improves the control accuracy and robustness of the force control system, reduces the effect of the disturbance torque on the control performance of the servo motor, and improves the overall force control performance of the system. Finally, experimental verification is performed using the PCDS performance test platform. The experimental results and quantitative data show that the QFT–DTOC proposed herein can significantly improve the force control performance of the PCDS. The relevant force control method can be used as a bottom-control method for the hydraulic servo system to provide a foundation for implementing the top-level trajectory planning of the robot.
Overview
CoChat Summary
TL;DR
The paper designs a pump–valve compound drive system (PCDS) for hydraulic legged-robot joint drive units and proposes a force control method combining quantitative feedback theory (QFT) with a disturbance torque observer (DTO), called QFT-DTOC. Experiments on a PCDS test platform show QFT-DTOC reduces force error compared with PID and QFT, with reported improvements of more than 41% versus PID and more than 20% for QFT alone.
Key findings
- In four experimental conditions, QFT-DTOC gave lower maximum force error than PID and QFT: for 1000 N/0.5 Hz without disturbance, PID 424.69 N, QFT 307.26 N, QFT-DTOC 209.41 N, with maximum elimination rate 50.69% for QFT-DTOC versus 27.65% for QFT; for 2000 N/0.5 Hz without disturbance, 807.01 N, 639.47 N, 368.76 N, with 54.31% versus 20.76%. With 8 mm/1 Hz disturbance, 1000 N gave 444.11 N, 330.28 N, 243.19 N, with 45.24% versus 25.63%; 2000 N gave 879.51 N, 692.61 N, 514.34 N, with 41.52% versus 21.25%.
- Average force error was also lower with QFT-DTOC: for example, condition ③ gave PID 239.96 N, QFT 169.87 N, QFT-DTOC 55.84 N, with average elimination rate 76.73% for QFT-DTOC versus 29.21% for QFT; condition ④ gave 443.82 N, 331.84 N, 111.43 N, with 74.89% versus 25.23%.
- The paper concludes that QFT improves control accuracy by more than 20% compared with PID, and QFT-DTOC improves accuracy by more than 41% compared with PID; DTO compensation improved disturbance rejection and mitigated phase-angle lag.
Methods
- A nonlinear mathematical model of the PCDS force closed-loop control system was built for the servo motor, gear pump, filling loop, asymmetrical cylinder, and pressure sensor; the pump-controlled asymmetric cylinder transfer function was simplified separately for positive and negative piston motion.
- The QFT controller was designed in the frequency domain with ±7% parameter uncertainty, object templates at selected frequency points, robust stability margins of GM = 5.27 dB and φM = 49.25°, and a target bandwidth of 3–10 Hz. The DTO estimates servo motor load torque and uses a low-pass filter with a third-order denominator and first-order numerator, N = 3, M = 1, k = 0.1, and τ = 0.001.
- Experimental verification used a PCDS performance test platform with a counter cylinder; a valve-controlled cylinder position control system simulated disturbance load. Conditions used sinusoidal force inputs of 1000 N and 2000 N at 0.5 Hz, with or without an 8 mm amplitude, 1 Hz sinusoidal disturbance position, comparing PID, QFT, and QFT-DTOC.
Limitations
- Stated in the paper: the PCDS test platform used an internal gear pump, which featured low-speed crawling, weak flow pressure pulsation, and other disadvantages, causing significant fluctuations in the force control curve; future work should investigate the low-speed characteristics of the internal gear pump and devise compensation methods.
- Stated in the paper: QFT alone produced a phase-angle lag because it is designed based on amplitude-frequency characteristics and does not satisfy corresponding phase-angle requirements; QFT-DTOC mitigated this. The paper also states that no experimental conditions were available for detecting disturbance torque, so the DTO estimated it indirectly.
- Evident from the text: the simplified transfer function assumes the low-pressure cavity of the asymmetric cylinder is zero and disregards external load and friction forces, which may limit model fidelity.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
2 Valid · 2 Not valid · 2 Not checked · 29 Own results and interpretations
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“Although it features a higher energy efficiency than that of the valve-controlled cylinder system, its response speed and control accuracy are lower.”
What the sources say
- Could not verifycites [9] Y H Song, K X Ba, Y Wang, et al.Study on nonlinear dynamic behavior and stability of aviation pressure servo valve-controlled cylinder system. Nonlinear Dynamics, 2022, 108(4): 3077–3103. sourceExperimental — accuracy not yet measured
Our copy of Song et al. (2022, Nonlinear Dynamics) is confined to the aviation brake pressure servo valve-controlled cylinder system (PSVCS): its Introduction (p. 1) frames the problem as the lack of research on self-excited oscillation of the brake pressure servo valve–actuator system, and Sections 2–6 model and test that system's nonlinear dynamics and stability. No passage discusses a pump-controlled cylinder system, nor compares energy efficiency, response speed or control accuracy of pump-controlled versus valve-controlled drives (searches: 'pump-controlled cylinder lower control accuracy than valve-controlled', 'energy efficiency direct pump valve compared with servo valve', 'control accuracy response speed comparison', 'valve-controlled advantages disadvantages throttling loss efficiency', 'pump controlled hydraulic cylinder literature review'). Since the paper neither states nor contradicts the attributed comparison, the claim cannot be checked against it. (LLM, conf=0.70)
- Could not verifycites [10] X M Yuan, W Q Wang, X Zhu, et al. Theory model of dynamic bulk modulus of aerated hydraulic fluid. Chinese Journal of Mechanical Engineering, 2022, 35:121. sourceExperimental — accuracy not yet measured
Our copy of Yuan et al. (2022) is entirely a theoretical/numerical study of the dynamic bulk modulus of aerated hydraulic fluid (Introduction, Sections 3-4 on numerical results and influencing factors, Section 5 model validation against Bin's compression measurements, Section 6 conclusions); no passage compares a pump-controlled cylinder system with a valve-controlled cylinder system in accuracy, response speed or energy efficiency. The nearest statement, in the Introduction, is only generic: 'Many factors affect the accuracy and energy efficiency of a hydraulic system, including system control strategies, structural forms, and external incentives'. Searches for 'pump-controlled cylinder control accuracy', 'valve-controlled comparison energy efficiency response speed', and 'throttle valve control system' returned only bulk-modulus text and reference-list entries (e.g., Lyu, Chen & Yao on pump-and-valve combined systems), which the paper does not use to make this comparison. (LLM, conf=0.72)
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Could not verify
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“This method improves the control accuracy and robustness of the force control system, reduces the effect of the disturbance torque on the control performance of the servo motor, and improves the overall force control performance of the system.”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on 8 assumptions not shown here.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“When the amplitude of the sine signal was increased, the system exhibited a significant following error.”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“When only QFT was adopted in the system, the response curve of the force control system featured a certain phase angle lag”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“In particular, in the case involving load position disturbance, the DTO compensation effect was better.”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
22 more claims
Create a free account to see all 35 claims and to verify the 4 references still open.
- Probably not a substantial claim. 3
- It may state two separate claims as one. 5
- The quote only partly states this claim. 1
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ 3.1.2 Determination of Parameter Uncertainty Set and System Template · p. 9
“The QFT controller was designed based on the transfer block diagram of the pump-controlled asymmetric cylinder force-control system shown in Figure 5”
§ 2.2.2 Mathematical Model Construction of Filling Loop · p. 4
“Figure 5 Diagram showing flow-pressure relationship between low pressure fuel tank and check valve oil replenishment”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ (2) Index of System Tracking Performance · p. 11
“To satisfy the two performance indexes, the open-loop Nichols curve of the system was adjusted to outside or above the comprehensive performance constraint boundary area”
§ (2) Index of System Tracking Performance · p. 11
“As shown, the frequency range of the system open-loop Nichols curve is inside or below the comprehensive performance constraint boundary region.”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ 4.1 Operating Principle of PCDS Experimental Platform · p. 14
“| Connection volume between rodless cavity and gear pump V g 1 | 3.93 × 10 -5 | m 3 | Connecting volume of rod cavity and gear pump V g 1 | 3.93 × 10 -5 | m 3 |”
§ 2.2.4 Mathematical Model Construction of Asymmetrical Cylinder · p. 5
“Vg 2 the pipe volume connected to the gear pump and the asymmetric cylinder rod cavity”
Citations
Cites
High-Precision Robust Force Control of a Series Elastic Actuator
Oh, S., & Kong, K. (2017) · IEEE/ASME Transactions on Mechatronics · doi:10.1109/tmech.2016.2614503 · Cited by 278 · cited 1×
“In recent years, hydraulic and motor force control systems have been investigated extensively, and various control meth-ods have been adopted, such as fuzzy logic control [11– 14], sliding mode control [15, 16], robust control [17, 18], and intelligent control [19–22].”
BackgroundPosition control of nonlinear hydraulic system using an improved PSO based PID controller
Ye, Y., Yin, C.-B., Gong, Y., & Zhou, J.-J. (2017) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2016.06.010 · Cited by 199 · cited 1×
“However, in the practical application of robot systems, to ensure the stability of the body, algorithms of the core controller based on PID are still necessitated [23–25].”
MethodAdaptive sliding mode trajectory tracking control for wheeled mobile robots
Zhai, J.-Y., & Song, Z.-B. (2019) · International Journal of Control · doi:10.1080/00207179.2018.1436194 · Cited by 187 · cited 1×
“Based on the motion mode, robots can be classified into wheeled, crawler, legged, serpentine, and spherical robots [1–5].”
BackgroundAn Adaptive Neural Network Controller for Active Suspension Systems With Hydraulic Actuator
Liu, Y.-J., Zeng, Q., Liu, L., & Tong, S. (2020) · IEEE Transactions on Systems, Man, and Cybernetics: Systems · doi:10.1109/tsmc.2018.2875187 · Cited by 125
Self-citationLyu, L., Chen, Z., & Yao, B. (2019) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2018.2875666 · Cited by 113 · cited 1×
“In recent years, hydraulic and motor force control systems have been investigated extensively, and various control meth-ods have been adopted, such as fuzzy logic control [11– 14], sliding mode control [15, 16], robust control [17, 18], and intelligent control [19–22].”
BackgroundBaigzadehnoe, B., Rahmani, Z., Khosravi, A., et al. (2017) · ISA Transactions · doi:10.1016/j.isatra.2017.07.029 · Cited by 111 · cited 1×
“In recent years, hydraulic and motor force control systems have been investigated extensively, and various control meth-ods have been adopted, such as fuzzy logic control [11– 14], sliding mode control [15, 16], robust control [17, 18], and intelligent control [19–22].”
BackgroundWon, D., Kim, W., & Tomizuka, M. (2017) · IEEE/ASME Transactions on Mechatronics · doi:10.1109/tmech.2017.2764110 · Cited by 100
Lyu, L., Chen, Z., & Yao, B. (2021) · IEEE Transactions on Control Systems Technology · doi:10.1109/tcst.2020.2974180 · Cited by 100 · cited 1×
“The typically used electro-hydraulic servo system is available two forms: the valve-controlled cylinder system [6–8] and pump-controlled cylinder system [9, 10].”
MethodA Kinect-Based Real-Time Compressive Tracking Prototype System for Amphibious Spherical Robots
Pan, S., Shi, L., & Guo, S. (2015) · Sensors · doi:10.3390/s150408232 · Cited by 79 · cited 1×
“Based on the motion mode, robots can be classified into wheeled, crawler, legged, serpentine, and spherical robots [1–5].”
BackgroundAdaptive Tracking Control of Hydraulic Systems With Improved Parameter Convergence
Guo, K., Li, M., Shi, W., & Pan, Y. (2022) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2021.3101006 · Cited by 76 · cited 1×
“In recent years, hydraulic and motor force control systems have been investigated extensively, and various control meth-ods have been adopted, such as fuzzy logic control [11– 14], sliding mode control [15, 16], robust control [17, 18], and intelligent control [19–22].”
Background
Cited by
Zhang, W., Wang, B., Wu, Z., Zhang, F., Zhang, J., Zhang, S., Zhang, J., Zhang, J., Sun, H., Waters, K. E., et al. (2025) · Precision Engineering · doi:10.1016/j.precisioneng.2025.07.011 · Cited by 17
Ba, K., Feng, X., Wang, Y., She, J., Song, Y., Ma, G. L., Yu, B., & Kong, X. (2024) · Applied Mathematical Modelling · doi:10.1016/j.apm.2024.115913 · Cited by 14
Self-citationYan, G., Zhang, T., Liu, X., Yao, C., & Ai, C. (2025) · International Journal of Electrical Power & Energy Systems · doi:10.1016/j.ijepes.2025.110991 · Cited by 11
He, H. X., & Yan, H. (2024) · Scientific Reports · doi:10.1038/s41598-024-80637-2 · Cited by 10
Dong, Z., Song, H., Liao, Y., Wang, H., Song, M., Jiang, J., & Chen, G. (2025) · Actuators · doi:10.3390/act14060261 · Cited by 6
“According to Equation (31), the MPC algorithm must incorporate the hydraulic die cushion work into its control calculations when the system’s state variables—such as the hydraulic cylinder displacement, cylinder speed, system pressure, and control volume output signals—are the actual control of the…”
Metadata
- Authors
- Ba, K., Wang, Y., He, X., Wang, C., Yu, B., Liu, Y., & Kong, X.
- Affiliations
- Yanshan University (CN)
- Corresponding author
- Yu, Bin
- Venue
- Chinese Journal of Mechanical Engineering
- Publisher
- Elsevier BV
- Published
- 2024-03-20
- Volume
- 37
- Issue
- 1
- ISSN
- 1000-9345 (ISSN-L)
- 2192-8258
- OpenAlex
- W4393012459
- Cited by
- 18
- References
- 32
- Citations by year
- 2026: 5 · 2025: 11 · 2024: 2
- FWCI
- 2.42
- Type
- journal article
- Language
- en
- Open access
- diamond
- doi.org
- Licence
- cc-by
- creativecommons.org/licenses/by/4.0 (tdm)
- creativecommons.org/licenses/by/4.0 (vor)
- Locations
- Chinese Journal of Mechanical Engineering (publishedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Funders
- National Excellent Natural Science Foundation of China (52122503)
- Hebei Provincial Natural Science Foundation of China (E2022203002)
- The Yanzhao’s Young Scientist Project of China (E2023203258)
- Science Research Project of Hebei Education Department (BJK2022060)
- Hebei Provincial Graduate Innovation Funding Project of China (CXZZSS2022129)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Hydraulic and Pneumatic Systems
- Physical Sciences › Engineering › Mechanical Engineering › Control Systems in Engineering
- Physical Sciences › Engineering › Control and Systems Engineering › Adaptive Control of Nonlinear Systems
- Keywords
- electro-hydraulic servo system, quantitative feedback theory, hydraulic drive unit, nonlinear system modeling, power loss reduction, nonlinear friction
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (qwen3.8-omni-flash).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Force Compensation Control for Electro-Hydraulic Servo System with Pump–Valve Compound Drive via QFT–DTOC. https://app.cochat.ai/papers/10.1186/s10033-023-00988-1
- The paper
- Ba, K., Wang, Y., He, X., Wang, C., Yu, B., Liu, Y., & Kong, X. (2024). Force Compensation Control for Electro-Hydraulic Servo System with Pump–Valve Compound Drive via QFT–DTOC. Chinese Journal of Mechanical Engineering. https://doi.org/10.1186/s10033-023-00988-1
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.