Experimental and Numerical Study on Regulation of Cutting Temperature during the Circular Sawing of 45 Steel
Open accessThe DOI matches its Crossref record; 26 of the 26 references it cites were found in a registry or an index; none of the 2 sources its claims cite is checked for support yet.
Abstract
Studying the cutting temperature is critical for unlocking the secrets of sawblade wear, lifespan, and the metallurgical alterations beneath the surface. This paper describes an investigation into the temperature of 45 steel during dry sawing, using a cemented carbide circular saw blade under various cutting conditions. A temperature acquisition system was developed, enabling the determination of the average temperature of the arc zone in the workpiece and the temperature of the sawtooth tip via a semi-automated thermocouple measurement and an embedded dynamic artificial thermocouple method, respectively. Results obtained from these two methods indicate a positive correlation between the sawing temperature and the saw blade speed and feed rate, with an optimal combination of cutting process parameters identified for maintaining stability within reasonable ranges. Finite element simulations reveal a cyclical fluctuation in temperature along the workpiece surface and sawtooth, with a gradual decrease after an increase in the intermittent step, and confirm the relationship between the sawing temperature and the saw blade and feed rates observed experimentally. Overall, this study presents valuable insights into the temperature changes occurring during the sawing process, with important implications for improving productivity and maintaining stability in industrial applications.
Overview
CoChat Summary
TL;DR
The paper develops and applies two thermocouple-based methods plus Deform 3D finite element simulation to measure and regulate cutting temperature during dry circular sawing of 45 steel with a cemented carbide blade. It finds sawing temperature rises with blade speed and feed rate, with an optimal parameter combination balancing temperature and productivity, and simulation shows cyclical temperature fluctuation along the workpiece surface and sawtooth.
Key findings
- Both the semi-artificial thermocouple method for the workpiece arc zone and the embedded dynamic artificial thermocouple method for the sawtooth tip showed general agreement and a positive correlation between sawing temperature and saw blade speed and feed rate; the relationship is influenced by single-tooth cutting layer thickness, so an optimal cutting parameter combination exists to balance sawing temperature and productivity.
- In experiments with feed rates of 1, 3, and 5 mm/s and blade speeds of 50, 100, and 150 r/min, sawing temperature rose with feed rate: below 3 mm/s it increased slowly, above 3 mm/s the increase intensified, and above 5 mm/s the increase slowed; blade speed produced an oscillating upward temperature trend.
- Simulation of single sawtooth cutting showed highest temperatures around the tooth tip and cutting edge and at the chip root, with transient sawing temperature reaching 1300 °C; heat was primarily located on the workpiece surface and carried away by the chip.
- Point-tracking simulation at 50 r/min and 5 mm/s showed cyclical workpiece surface temperature fluctuation with gradual decrease as intermittent steps increased; points P3 and P4 rose sharply due to severe material removal and tool-chip friction, and full-factor simulation confirmed positive correlation of saw blade speed and feed rate with sawing temperature.
Methods
- Dry sawing experiments used 45 steel workpieces (30 mm × 30 mm; round steel radius 15 mm) on a SANDE SD-70R high-speed metal circular saw (7.5 kW) with a 60-tooth cemented carbide circular saw blade (outer diameter 285 mm; base plate 1.7 mm; tooth edge 2 mm). Data acquisition used an NI USB-6211 card and LabVIEW at 20 kHz sampling; cutting speed reached 150 r/min, corresponding to 134.30 m/min at the sawtooth tip, with 254.65 µs sawing time, contact length L = 0.57 mm, and 5–15 data points per cut.
- Temperature measurement used a semi-artificial thermocouple with constantan wire (0.5 mm starting diameter, 0.85 mm after rolling) and 0.02 mm mica insulation for arc-zone average temperature, and an embedded dynamic artificial thermocouple with two enameled wires (0.5 mm diameter) and a 0.2 mm mica sheet for sawtooth tip temperature, with the cold end kept at 20 °C.
- Numerical work used Deform 3D finite element simulation with the Johnson-Cook flow stress model; a 1:1 carbide circular saw blade model was simplified by removing four installation positioning holes, the workpiece was deformable with tetrahedral mesh and 1:10 mesh refinement, initial temperature was 20 °C, friction factor was 0.4, heat conduction coefficient was 45 W/(m·K), and a full-factor test design examined speed and feed effects.
Limitations
- Stated: the embedded dynamic thermocouple signal can be interfered with because the thermocouple wires are not in constant contact except at the exact moment the saw teeth intersect them, potentially obscuring the meaningful signal; however, the interference amplitude is smaller than the peak value and the peak mean was used, so its impact was disregarded.
- Stated/general: finite element numerical methods face challenges in defining material properties and boundary conditions, making it difficult to precisely mirror nonlinear problems involving material properties, deformation, and multi-coupling fields.
- Evident from the text: the simulation simplified the saw blade by eliminating four installation positioning holes; experiments were limited to dry sawing of 45 steel under specific blade speeds (50, 100, 150 r/min) and feed rates (1, 3, 5 mm/s), and the “optimal combination” of cutting parameters is not numerically specified in the provided text.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures

















Verification
Claims the paper makes
0 Valid · 3 Not valid · 1 Not checked · 79 Own results and interpretations
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Finite element simulations reveal a cyclical fluctuation in temperature along the workpiece surface and sawtooth, with a gradual decrease after an increase in the intermittent step, and confirm the relationship between the sawing temperature and the saw blade and feed rates observed experimentally.”
§ Experimental and Numerical Study on Regulation of Cutting Temperature during the Circular Sawing of 45 Steel > Abstract
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The starting and ending positions of the sharp pulse signal reflect the temperature variation range of the sawing arc zone.”
§ Experimental and Numerical Study on Regulation of Cutting Temperature during the Circular Sawing of 45 Steel > 4.1.1. Semi-Artificial Thermocouple
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on an assumption not shown here.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“A thorough analysis of the chips procured from the site reveals the predomination of banded chips, with occasional instances of squeezed chips.”
§ Experimental and Numerical Study on Regulation of Cutting Temperature during the Circular Sawing of 45 Steel > 4. Results and Discussion
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Results obtained from these two methods indicate a positive correlation between the sawing temperature and the saw blade speed and feed rate, with an optimal combination of cutting process parameters identified for maintaining stability within reasonable ranges.”
§ Experimental and Numerical Study on Regulation of Cutting Temperature during the Circular Sawing of 45 Steel > Abstract
hedgedstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Finite element simulations reveal a cyclical fluctuation in temperature along the workpiece surface and sawtooth, with a gradual decrease after an increase in the intermittent step, and confirm the relationship between the sawing temperature and the saw blade and feed rates observed experimentally.”
§ Experimental and Numerical Study on Regulation of Cutting Temperature during the Circular Sawing of 45 Steel > Abstract
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
39 more claims
Create a free account to see all 83 claims and every source verdict.
- Borderline: one of the tests for a substantial claim is unclear. 2
- It may state two separate claims as one. 28
- Probably not a substantial claim. 14
- The quote only partly states this claim. 2
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Experimental and Numerical Study on Regulation of Cutting Temperature during the Circular Sawing of 45 Steel > 4.1.1. Semi-Artificial Thermocouple
“the workpiece (made of 45 steel) serves as the positive pole and a copper wire act as the negative pole”
§ Experimental and Numerical Study on Regulation of Cutting Temperature during the Circular Sawing of 45 Steel > 2.2. Experimental Procedure
“The authors chose to use constantan wire for their experimental thermocouple, with a starting diameter of 0.5 mm and a width after rolling of 0.85 mm.”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Experimental and Numerical Study on Regulation of Cutting Temperature during the Circular Sawing of 45 Steel > 1. Introduction
“Mote et al. [31] examined the temperature difference between two concentric annular regions on the saw blade's surface”
§ Experimental and Numerical Study on Regulation of Cutting Temperature during the Circular Sawing of 45 Steel > References
“31. Merhar, M.; Bucar, D.G. The Influence of Radial Slots on Dynamic Stability of Thermally Stressed Circular Saw Blade/Utjecaj radijalnih utora na dinamicku stabilnost termicki napregnutog lista kruzne pile.”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Experimental and Numerical Study on Regulation of Cutting Temperature during the Circular Sawing of 45 Steel > 2.2. Experimental Procedure
“The authors chose to use constantan wire for their experimental thermocouple, with a starting diameter of 0.5 mm and a width after rolling of 0.85 mm.”
§ Experimental and Numerical Study on Regulation of Cutting Temperature during the Circular Sawing of 45 Steel > 4.1.1. Semi-Artificial Thermocouple
“the workpiece (made of 45 steel) serves as the positive pole and a copper wire act as the negative pole”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Experimental and Numerical Study on Regulation of Cutting Temperature during the Circular Sawing of 45 Steel > 1. Introduction
“Mote et al. [31] examined the temperature difference between two concentric annular regions on the saw blade's surface”
§ Experimental and Numerical Study on Regulation of Cutting Temperature during the Circular Sawing of 45 Steel > References
“31. Merhar, M.; Bucar, D.G. The Influence of Radial Slots on Dynamic Stability of Thermally Stressed Circular Saw Blade”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Experimental and Numerical Study on Regulation of Cutting Temperature during the Circular Sawing of 45 Steel > 4.1.2. Implanted Thermocouple
“the temperature evaluation of the sawing zone obtained via the semi-artificial thermocouple technique described in Section 3.2 of this paper.”
§ Experimental and Numerical Study on Regulation of Cutting Temperature during the Circular Sawing of 45 Steel > 3.2. Boundary Conditions
“## 3.2. Boundary Conditions”
Citations
Cites
Radulescu, R., & Kapoor, S. G. (1994) · Journal of Engineering for Industry · doi:10.1115/1.2901923 · Cited by 92
Qi, H., Wen, D., Yuan, Q., Zhang, L., & Chen, Z. (2016) · Powder Technology · doi:10.1016/j.powtec.2016.08.057 · Cited by 84
Self-citationQi, H., Wen, D., Lu, C., & Li, G. (2016) · International Journal of Mechanical Sciences · doi:10.1016/j.ijmecsci.2016.03.013 · Cited by 83
Qi, H., Qin, S., Cheng, Z., Teng, Q., Hong, T., & Xie, Y. (2021) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2021.01.048 · Cited by 56
Qi, H., Qin, S., Cheng, Z., Zou, Y., Cai, D., & Wen, D. (2021) · Powder Technology · doi:10.1016/j.powtec.2020.10.043 · Cited by 54
Zhang, L., Yuan, Z., Qi, Z., Cai, D., Cheng, Z., & Qi, H. (2018) · Powder Technology · doi:10.1016/j.powtec.2018.04.046 · Cited by 53
Zhang, L., Ji, R., Fu, Y., Qi, H., Kong, F., Li, H., & Tangwarodomnukun, V. (2019) · Powder Technology · doi:10.1016/j.powtec.2019.10.032 · Cited by 53
Xie, X., Zhang, L., Zhu, L., Li, Y., Hong, T., Yang, W., & Shan, X. (2023) · Coatings · doi:10.3390/coatings13050859 · Cited by 49
Nasir, V., Kooshkbaghi, M., Cool, J., & Sassani, F. (2021) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-020-06473-6 · Cited by 48
Investigation of the heat flow through bonded and brazed metal cutting tools
Darwish, S., & Davies, R. (1989) · International Journal of Machine Tools and Manufacture · doi:10.1016/0890-6955(89)90034-5 · Cited by 43
Research works printed but not linked: 4
- Wu, 2023, Construction of a calibration field of absolute gravity in a cave using the Cold Atom Gravimeter, Sensors, 23, Submitted
- Li, 2002, Thermal and rotary stresses in circular saw blades, J. Beijing For. Univ., 24, 14
- An, 2021, Effects of temperature and centrifugal load on transverse stiffness of circular saw blades with different structures, Chin. J. Wood Sci. Technol., 35, 5
- Zhang, 2006, Thermal stress analysis of new combined diamond saw blades, Diam. Abras. Eng., 152, 4
Cited by
Xie, X., Zhang, L., Zhu, L., Li, Y., Hong, T., Yang, W., & Shan, X. (2023) · Coatings · doi:10.3390/coatings13050859 · Cited by 49
Qian, H., Chen, M., Qi, Z., Teng, Q., Qi, H., Zhang, L., & Shan, X. (2023) · Crystals · doi:10.3390/cryst13030428 · Cited by 33
Ji, R., Qi, Z., Chen, J., Zhang, L., Lin, K., Lu, S., & Li, Y. (2023) · Crystals · doi:10.3390/cryst13030430 · Cited by 32
Zhao, X., Gu, K., Zhang, M., Weng, Z., Pan, R., Liu, B., & Wang, J. (2025) · Materials Science and Engineering A · doi:10.1016/j.msea.2025.147919 · Cited by 31
Yuan, H., Yang, W., Zhang, L., & Hong, T. (2023) · Coatings · doi:10.3390/coatings13030581 · Cited by 12
Metadata
- Authors
- Wang, Y., Wang, Z., Ni, P., Wang, D., Lu, Y., Lu, H., Guo, S., & Chen, Z.
- Affiliations
- Zhejiang University of Technology (CN)
- Zhejiang Guanbao Industrial Co., Ltd., Lishui 321400, China
- Hangzhou Wheeler General Machinery Co., Ltd., Hangzhou 311400, China
- Hangzhou Kenshang Information Technology Co., Ltd., Hangzhou 311400, China
- Corresponding author
- Chen, Zhenzhen
- Venue
- Coatings
- Publisher
- MDPI AG
- Published
- 2023-04-10
- Volume
- 13
- Issue
- 4
- Pages
- 758
- ISSN
- 2079-6412 (ISSN-L)
- OpenAlex
- W4364359885
- Semantic Scholar
- 052ccba95440fcc22a09cdafbe51572fe395903b
- Cited by
- 13
- References
- 25
- Citations by year
- 2025: 3 · 2024: 2 · 2023: 8
- FWCI
- 1.28
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Coatings (publishedVersion, cc-by)
- Funders
- National Natural Science Foundation of China (51705463, LTGS23E050001)
- Zhejiang Provincial Natural Science Foundation of China (51705463, LTGS23E050001)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Advanced machining processes and optimization
- Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Engineering Technology and Methodologies
- Physical Sciences › Materials Science › Metals and Alloys › Metal Alloys Wear and Properties
- Keywords
- cutting temperature, circular sawing, AISI 1045 steel, saw blade wear, cutting parameters, feed rate, finite element analysis, temperature distribution
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
A language model drew the claims from the paper on 2026-09-28, under version 3 of the claim definition (prompt extract-v3).
A second model labelled each claim on 2026-09-28 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Experimental and Numerical Study on Regulation of Cutting Temperature during the Circular Sawing of 45 Steel. https://app.cochat.ai/papers/10.3390/coatings13040758
- The paper
- Wang, Y., Wang, Z., Ni, P., Wang, D., Lu, Y., Lu, H., Guo, S., & Chen, Z. (2023). Experimental and Numerical Study on Regulation of Cutting Temperature during the Circular Sawing of 45 Steel. Coatings. https://doi.org/10.3390/coatings13040758
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.