Sub- and Supercritical Water Liquefaction of Kraft Lignin and Black Liquor Derived Lignin
Open accessThe DOI matches its Crossref record; 151 of the 151 references it cites were found in a registry or an index; 56 of the 234 sources its claims cite were checked for support.
Abstract
To mitigate global warming, humankind has been forced to develop new efficient energy solutions based on renewable energy sources. Hydrothermal liquefaction (HTL) is a promising technology that can efficiently produce bio-oil from several biomass sources. The HTL process uses sub- or supercritical water for producing bio-oil, water-soluble organics, gaseous products and char. Black liquor mainly contains cooking chemicals (mainly alkali salts) lignin and the hemicellulose parts of the wood chips used for cellulose digestion. This review explores the effects of different process parameters, solvents and catalysts for the HTL of black liquor or black liquor-derived lignin. Using short residence times under near- or supercritical water conditions may improve both the quality and the quantity of the bio-oil yield. The quality and yield of bio-oil can be further improved by using solvents (e.g., phenol) and catalysts (e.g., alkali salts, zirconia). However, the solubility of alkali salts present in black liquor can lead to clogging problem in the HTL reactor and process tubes when approaching supercritical water conditions.
Overview
CoChat Summary
TL;DR
This review synthesizes hydrothermal liquefaction (HTL) of black liquor and black liquor-derived lignin, focusing on process parameters, salts, catalysts, co-solvents, reaction chemistry, bio-oil quality, and techno-economics. It concludes that HTL is promising but faces key challenges from salt precipitation/fouling, limited continuous supercritical-water data, and bio-oil costs above fossil crude.
Key findings
- Reported bio-oil yields vary widely: up to 80 wt.% carbon yield from black liquor to bio-oil; Table 6 lists maxima of 87.7 wt.% for LignoBoost lignin in a continuous catalytic fixed-bed reactor, 78 wt.% for black liquor in batch, and 90 wt.% for alkali lignin in batch with ethanol.
- Temperature and residence time strongly affect yields: Orebom et al. found bio-oil yield rose from ca. 67 wt.% to a maximum of 78 wt.% at ca. 648 K, then fell to ca. 60 wt.% at 693 K; at 653 K, maximum bio-oil yield was 76 wt.% at 20 min, decreasing to ca. 68 wt.% at 120 min. Lee et al. reported highest bio-oil yield ca. 62 wt.% at 623 K and 5 min, with yields dropping to ca. 30 wt.% at 30 min above ca. 620 K.
- Black liquor salts can foul reactors: at HTL water densities of roughly 400–750 kg/m³, sodium sulfate solubility can fall from ca. 200 g/kg to 2 g/kg and sodium carbonate to 5 g/kg; a Paul Scherrer Institute salt separator recovered >95% of a K₂SO₄/Na₂CO₃ mixture as concentrated brine.
- Additives and economics: phenol as co-solvent raised bio-oil yield from 34 to 102 wt.% as initial phenol increased from 0 to 10 wt.%; K₂CO₃ increased phenolic yield from 16.9 to 27.1 wt.% but suspended solids from 0.1 to 22.9 wt.%; ZrO₂ gave 15.9 wt.% light oil versus 8.4 wt.% with glass beads. Techno-economic assessments reported minimum selling prices of 0.93–1.05 $/liter, while Brent crude averaged 0.36–0.83 $/liter over five years.
Methods
- Design: narrative literature review of HTL applied to black liquor and black liquor-derived lignin, covering process parameters, salt behavior, catalysts, co-solvents, reaction pathways, bio-oil quality, and techno-economic analyses.
- Data: published experimental studies and TEAs using feedstocks including black liquor, Kraft lignin, LignoBoost lignin, alkali lignin, and Indulin AT, with batch, continuous, catalytic fixed-bed, and CSTR systems.
- Analysis: thematic synthesis and comparison of reported yields, product compositions, process conditions, and economic estimates; no new experiments are reported.
Limitations
- Stated: comparing studies is difficult because of different feedstocks, experimental methodologies, and ways of expressing mass yields; there is no data from continuous supercritical-water reactors on black liquor; no complete reaction mechanism or kinetic model exists for black liquor lignin degradation, and the suitability of the Indulin AT model for black liquor is unclear.
- Stated: salt mixture phase behavior in supercritical water is hard to predict, and no specific study has been published on black liquor salt mixtures; research on corrosion-resistant materials for black liquor HTL is lacking.
- Evident: as a review, it provides no primary experimental validation and depends on heterogeneous cited studies; several reported comparisons are limited by inconsistent data presentation across sources.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures
![Figure 1 The main material flows in a Kraft pulp mill process. ( DM = Dry Matter). The figure is redrawn from Biermann [33]. Figure 1. The main material flows in a Kraft pulp mill process. ( DM = Dry Matter). The figure is redrawn from Biermann [33].](https://figures.cochat.ai/paper-figures/9d7a7584a57b46e98438a4ad311956ea/sub-and-supercritical-water-liquefaction-of-kraft-lignin-and-black-liquor-figure-1.png)
![Figure 2 Density and enthalpy of water as a function of temperature at various pressures. The data points are taken from Wagner and Pruß [60]: ( a ) density; ( b ) enthalpy. Figure 2. Density and enthalpy of water as a function of temperature at various pressures. The data points are taken from Wagner and Pruß [60]: ( a ) density; ( b ) enthalpy.](https://figures.cochat.ai/paper-figures/9dafd68b564d4f8d8f20b2ef1d73fc19/sub-and-supercritical-water-liquefaction-of-kraft-lignin-and-black-liquor-figure-2.png)

![( a ) ( b ) Figure 4. Logarithmic ionic product ( pKw ) and dielectric constant ( ε 0 ) of water as a function of temperature at various pressures. The data points are taken from IAPWS [63,64]: ( a ) Ionic product Figure 4. Logarithmic ionic product ( pKw ) and dielectric constant ( ε 0 ) of water as a function of temperature at various pressures. The data points are taken from IAPWS [63,64]: ( a ) Ionic product (pKw); ( b ) Dielectric Constant. Figure 4. Logarithmic ionic product ( pKw ) and dielectric constant ( " 0 ) of water as a function of temperature at various pressures. The data points are taken from IAPWS [63,64]: ( a ) Ionic product (pKw); ( b ) Dielectric Constant.](https://figures.cochat.ai/paper-figures/c6d3e460b8e540ffbab5c5f7f9ab72df/sub-and-supercritical-water-liquefaction-of-kraft-lignin-and-black-liquor-figure-4.png)



![Figure 8 Effect of temperature on mass fractions of monocyclic aromatic compounds in bio-oil. Data is taken from [107]. The curves are guides to the eye. Figure 8. E ect of temperature on mass fractions of monocyclic aromatic compounds in bio-oil. Data is taken from [107]. The curves are guides to the eye. Energies 2020 , 13 , x FOR PEER REVIEW 17 of 46](https://figures.cochat.ai/paper-figures/509d31438550473fbce2dd01fca22faf/sub-and-supercritical-water-liquefaction-of-kraft-lignin-and-black-liquor-figure-8.png)



![Figure 12 Effect of the initial KOH concentration on the total yields (both WSO and bio-oil) of various components. The feedstock for the HTL process was Kraft lignin. The curves are guides to the eye. Data is taken from Belkheiri et al. [115]. Figure 12. E ect of the initial KOH concentration on the total yields (both WSO and bio-oil) of various components. The feedstock for the HTL process was Kraft lignin. The curves are guides to the eye. Data is taken from Belkheiri et al. [115].](https://figures.cochat.ai/paper-figures/58fd900c117e4c549d1904b5704d6a43/sub-and-supercritical-water-liquefaction-of-kraft-lignin-and-black-liquor-figure-12.png)
![Figure 13 Reaction pathway for the degradation of Indulin AT. Figure is adapted from Schuler [140].](https://figures.cochat.ai/paper-figures/3fb59045727646098e92d407bca32b0a/sub-and-supercritical-water-liquefaction-of-kraft-lignin-and-black-liquor-figure-13.png)
Verification
Claims the paper makes
52 Valid · 15 Not valid · 141 Not checked · 98 Own results and interpretations
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“The mass yield of carbon from black liquor to bio-oil can be up to 80 wt.% [58].”
What the sources say
- Partly supportedcites [58] Orebom, 2018, High Yields of Bio Oils from Hydrothermal Processing of Thin Black Liquor without the Use of Catalysts or Capping Agents, ACS Omega sourceExperimental — accuracy not yet measured
The Abstract reports that, under optimal conditions, extractable organics yielded around 80% of the original lignin. It does not report that 80 wt.% of the carbon in black liquor was transferred to bio-oil; the claim changes both the measured material and the yield basis. (LLM, conf=0.88)
- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Nevertheless, it must be emphasized that the process conditions and the origin of the wood chips have a great influence on the produced black liquor and its properties [45].”
§ Sub-and Supercritical Water Liquefaction of Kraft Lignin and Black Liquor Derived Lignin > 2.2. Formation of Black Liquor
What the sources say
- Partly supportedcites [45] Lancefield, 2018, Identification of a diagnostic structural motif reveals a new reaction intermediate and condensation pathway in kraft lignin formation, Chem. Sci. sourceExperimental — accuracy not yet measured
In Results and discussion (page unavailable), the paper reports that substrate concentration changes the reaction mixtures and dominant kraft chemistry pathways. It also examines kraft lignins from softwood and hardwood sources, but does not establish that wood-chip origin has a great influence on the produced black liquor or its properties. Its evidence concerns particular lignin structures and model reactions, not black-liquor properties generally. (LLM, conf=0.78)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Over that temperature range, the bio-oil yield increased from ca. 67 wt.% to a maximum of 78 wt.% (ca.648 K), before falling back to ca. 60 wt.% at 693 K.”
§ Sub-and Supercritical Water Liquefaction of Kraft Lignin and Black Liquor Derived Lignin > 3.4.1. Temperature and Pressure
What the sources say
- Partly supportedcites [58] Orebom, 2018, High Yields of Bio Oils from Hydrothermal Processing of Thin Black Liquor without the Use of Catalysts or Capping Agents, ACS Omega sourceExperimental — accuracy not yet measured
The Temperature Dependence section (page unavailable) reports that bio-oil yield rose from 340 °C, peaked at 370–380 °C (about 648 K), and declined above 380 °C. Our text copy does not give the claimed yields of approximately 67, 78, and 60 wt.% at those temperatures; Figure 1 is present only as a caption, so those values cannot be verified. (LLM, conf=0.82)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The sources with a verdict support this claim; the rest weren’t checked yet, have no full text we could read, or their verdicts aren’t rated yet.
In the paper
“Lignin degradation occurs via different reactions, such as hydrolysis, alkylation and repolymerization reactions [95,96].”
§ Sub-and Supercritical Water Liquefaction of Kraft Lignin and Black Liquor Derived Lignin > 3.3. Hydrothermal Liquefaction (HTL)
What the sources say
- Not checked — no full text of the sourcecites [95] Sasaki, 2008, Recovery of phenolic compounds through the decomposition of lignin in near and supercritical water, Chem. Eng. Process. Process Intensif. source
- Supportedcites [96] Schuler, 2019, Lignin from bark as a resource for aromatics production by hydrothermal liquefaction, GCB Bioenergy source
Section 4, “Cleavage Reactions,” identifies hydrolysis and alkylation as main reactions during lignin hydrothermal liquefaction and says that radicals formed at higher temperatures accelerate repolymerization. This supports the cited examples of reactions involved in lignin degradation. (LLM, conf=0.92)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“The authors reported a global decrease in bio-oil and energy yields from 85 wt.% to 69 wt.% as the temperature increased from 563 K to 643 K.”
§ Sub-and Supercritical Water Liquefaction of Kraft Lignin and Black Liquor Derived Lignin > Nguyen et al.
What the sources say
- Partly supportedcites [107] Nguyen, 2014, The effect of temperature on the catalytic conversion of Kraft lignin using near-critical water, Bioresour. Technol. sourceExperimental — accuracy not yet measured
Section 3.4 (p. 8) reports that dry lignin-oil yield fell from about 85–88% to 69% as temperature rose from 290°C to 370°C (approximately 563–643 K). The paper does not report an energy-yield decrease from 85 wt.% to 69 wt.%; Section 3.3 (p. 7) discusses the oil’s heat value separately. (LLM, conf=0.86)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
129 more claims · 18 with their cited sources checked
Create a free account to see all 306 claims and every source verdict.
- Probably not a substantial claim. 85
- It may state two separate claims as one. 115
- The quote only partly states this claim. 4
- Not yet classified. 1
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“This is surprising because the main drivers for depolymerization of lignin according to the literature are carbonates and hydroxides.13”
From The Impact of Sulfur-Containing Inorganic Compounds during the Depolymerization of Lignin by Hydrothermal Liquefaction of Black Liquor (2024) · cites this paper as [13]
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
“The yield of bio-oil varied between 58.3 wt.% and 63.6 wt.% while the yield of WSO fluctuated between 14.7 wt.% and 26.6 wt.% as the phenol concentration was changed from 2.0 wt.% to 10.0 wt.%.The yield of char staid stable at ca. 60 wt.% whatever the phenol concentration.”
§ Sub-and Supercritical Water Liquefaction of Kraft Lignin and Black Liquor Derived Lignin > Belkheiri et al.
Reported 100 · recomputed 133
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Sub-and Supercritical Water Liquefaction of Kraft Lignin and Black Liquor Derived Lignin > Nguyen et al.
“increasing the pressure at a set temperature (increasing the density)”
§ Sub-and Supercritical Water Liquefaction of Kraft Lignin and Black Liquor Derived Lignin > Nguyen et al.
“the yield of phenol, m-, p-and p-cresols increased at higher water densities (i.e., lower pressure)”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Sub-and Supercritical Water Liquefaction of Kraft Lignin and Black Liquor Derived Lignin > 4.1. Reaction Pathways and Kinetics
“Coniferyl alcohol → guaiacol + different side products C 10 H 12 O 3 → C 7 H 8 O 2 + C n H m O p (2)”
§ Sub-and Supercritical Water Liquefaction of Kraft Lignin and Black Liquor Derived Lignin > 4.1. Reaction Pathways and Kinetics
“guaiacol → catechol (→ 4 -methylcatechol) C 7 H 8 O 3 + 2H + → C 6 H 6 O 2 + CH 4”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Sub-and Supercritical Water Liquefaction of Kraft Lignin and Black Liquor Derived Lignin > Belkheiri et al.
“The use of initial concentrations of methanol and phenol of 39 wt.% and 3.9 wt.% at 583 K led to the lowest char yield of 14.1 wt.%.”
§ Sub-and Supercritical Water Liquefaction of Kraft Lignin and Black Liquor Derived Lignin > Belkheiri et al.
“Similarly, the yields of char and WSO were 38.8 wt.% and 24 wt.%, respectively.”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Sub-and Supercritical Water Liquefaction of Kraft Lignin and Black Liquor Derived Lignin > 6. Conclusions
“The highest yield of bio-oil of in a continuously operated plant was received under subcritical conditions at around 573 K and residence time of around 12 min.”
§ Sub-and Supercritical Water Liquefaction of Kraft Lignin and Black Liquor Derived Lignin > -
“| LignoBoost lignin | catalytic Fixed Bed | 87.7 wt.% | 98.5% | 25 MPa, Phenol 4.0 wt.%, K 2 CO 3 1.6 wt.%, Solid | 10-13 min | [107,119] |”
2 more findings
Create a free account to see every finding of this check.
Citations
Cites
Wagner, W., & Pruß, A. (2002) · Journal of Physical and Chemical Reference Data · doi:10.1063/1.1461829 · Cited by 4,884 · cited 3×
“5 MPa, 489 kg/m3 at 25 MPa, 637 kg/m3 at 50 MPa and 815 kg/m3 at 200 MPa [60].”
MethodInfluentialEnergy production from biomass (part 1): overview of biomass
McKendry, P. (2002) · Bioresource Technology · doi:10.1016/s0960-8524(01)00118-3 · Cited by 4,860
Chemicals from lignin: an interplay of lignocellulose fractionation, depolymerisation, and upgrading
Schutyser, W., Renders, T., Van den Bosch, S., Koelewijn, S.-F., Beckham, G. T., & Sels, B. F. (2018) · Chemical Society Reviews · doi:10.1039/c7cs00566k · Cited by 2,552 · cited 1×
“Alkylthiols, thioaldehydes and thioketones are among the organosulfur compounds most likely to be present in black liquor, or to be formed in the early stages of Kraft lignin decomposition [145].”
BackgroundHydrothermal liquefaction of biomass: A review of subcritical water technologies
Toor, S. S., Rosendahl, L., & Rudolf, A. (2011) · Energy · doi:10.1016/j.energy.2011.03.013 · Cited by 1,840 · cited 2×
“The hydrogen produced in WGS may act as a reducing agent in HTL reactions, thus improving the overall quality of the bio-oil produced [102].”
BackgroundMethodA review on hydrothermal liquefaction of biomass
Gollakota, A. R. K., Kishore, N., & Gu, S. (2018) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2017.05.178 · Cited by 1,306 · cited 2×
“Those HTL review articles that do exist either focus on the HTL of biomasses from different sources [21,22], the HTL of pure lignin compounds [23], or the HTL of a specific biomass, such as wood [24], algae [25–27], agricultural and forestry waste [28], and even swine manure [29].”
BackgroundReview of current and future softwood kraft lignin process chemistry
Chakar, F. S., & Ragauskas, A. J. (2004) · Industrial Crops and Products · doi:10.1016/j.indcrop.2004.04.016 · Cited by 1,203
Tejado, A., Peña, C., Labidi, J., Echeverria, J. M., & Mondragon, I. (2007) · Bioresource Technology · doi:10.1016/j.biortech.2006.05.042 · Cited by 1,112 · cited 2×
“The catalysts for this process are both hydroxyl and hydrosulfide ions [34,44].”
BackgroundHydrothermal liquefaction of biomass: Developments from batch to continuous process
Elliott, D. C., Biller, P., Ross, A. B., Schmidt, A. J., & Jones, S. B. (2015) · Bioresource Technology · doi:10.1016/j.biortech.2014.09.132 · Cited by 969 · cited 1×
“Several research groups have taken advantage of the low salt solubility to extract salts from a main stream, using, for instance, continuous filtration [89], semi-continuous salt trap [75,82,84], or continuous extraction [77,90–92].”
BackgroundLópez Barreiro, D., Prins, W., Ronsse, F., & Brilman, W. (2013) · Biomass and Bioenergy · doi:10.1016/j.biombioe.2012.12.029 · Cited by 695
Biomass Gasification in Supercritical Water
Antal, M. J., Allen, S. G., Schulman, D., Xu, X., & Divilio, R. J. (2000) · Industrial & Engineering Chemistry Research · doi:10.1021/ie0003436 · Cited by 610
Research works printed but not linked: 12
- Sims, R.E.H. (2003). Bioenergy Options for a Cleaner Environment in Developed and Developing Countries, Elsevier Science & Technology.
- International Energy Agency Black Liquor Gasification (2007). Summary and Conclusions from the IEA Bioenergy ExCo54 Workshop, International Energy Agency.
- Sjöström, E. (1981). Wood Chemistry: Fundamentals and Applications, Academic Press.
- Stokke, D.D., Wu, Q., Han, G., and Stevens, C.V. Introduction to Wood and Natural Fiber Composites, John Wiley & Sons, Incorporate. [1st ed.].
- Sjöström, E. (1993). Wood Chemistry: Fundamentals and Applications, Academic Press, Inc.. [2nd ed.].
- Sjöström, E. (1965). Preface to the first edition. Wood Chemistry: Fundamentals and Applications, Academic Press, Inc.
- Rumyantsev, 1977, Selection of mineralizers in the hydrothermal synthesis and growth of crystals, Sov. Phys. Crystallogr., 22, 610
- Tomani, 2010, The lignoboost process, Cellul. Chem. Technol., 44, 53
- Välimäki, A. (2017). Mustalipeän hydrotermisen nesteytyksen vaikutus bioöljyn laatuun (Improving bio-oil quality in hydrothermal liquefaction of black liquor). [Master’s Thesis, Aalto University].
- Tran, 1990, Chloride and Potassium in the Kraft Recovery Cycle: A Practical Guide, Pulp Pap. Can. Ont., 91, 185
- Hupa, 2007, Recovery boiler chemical principles, TAPPI Kraft Recover. Course, 2007, 2
- Schuler, J. (2019). Hydrothermal Liquefaction of Lignin. [Ph.D. Thesis, Karlsruhe Institute of Technology].
Cited by
Lignins as Promising Renewable Biopolymers and Bioactive Compounds for High-Performance Materials
Vasile, C., & Baican, M. (2023) · Polymers · doi:10.3390/polym15153177 · Cited by 251
Kraft Lignin: A Valuable, Sustainable Resource, Opportunities and Challenges
Argyropoulos, D. D. S., Crestini, C., Dahlstrand, C., Furusjö, E., Gioia, C., Jedvert, K., Henriksson, G., Hulteberg, C., Lawoko, M., Pierrou, C., et al. (2023) · ChemSusChem · doi:10.1002/cssc.202300492 · Cited by 231
Grande, L., Pedroarena, I., Korili, S. A., & Gil, A. (2021) · Materials · doi:10.3390/ma14185286 · Cited by 130
“Thanks to these properties, supercritical water becomes an apolar solvent for most organic reactions [55,84].”
BackgroundKraft black liquor as a renewable source of value-added chemicals
Pola, L., Collado, S., Oulego, P., & Díaz, M. (2022) · Chemical Engineering Journal · doi:10.1016/j.cej.2022.137728 · Cited by 135
Green, efficient extraction of bamboo hemicellulose using freeze-thaw assisted alkali treatment
Li, J., Liu, Z., Feng, C., Liu, X., Qin, F., Liang, C., Bian, H., Qin, C., & Yao, S. (2021) · Bioresource Technology · doi:10.1016/j.biortech.2021.125107 · Cited by 107
Güleç, F., Anburajan, P., Umenweke, G. C., Musa, U., Williams, O. S. A., Mortezaei, Y., Suk‐Oh, H., Lester, E. H., Ogbaga, C. C., Gunes, B., et al. (2023) · Biofuels Bioproducts and Biorefining · doi:10.1002/bbb.2544 · Cited by 103
“109 Hydrothermal liquefaction is usually conducted at a moderately higher temperature (280– 370°C) and pressure (4– 25 MPa) in the presence of a solvent medium.”
BackgroundGhadge, R., Nagwani, N., Saxena, N., Dasgupta, S., & Sapre, A. V. (2022) · Energy Conversion and Management X · doi:10.1016/j.ecmx.2022.100223 · Cited by 129
Radhakrishnan, R., Patra, P., Das, M., & Ghosh, A. (2021) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2021.111368 · Cited by 62
de Menezes, F. F., Nascimento, V. M., Gomes, G. R., Rocha, G. J. M., Strauss, M., Junqueira, T. L., & Driemeier, C. (2023) · Fuel · doi:10.1016/j.fuel.2023.127796 · Cited by 70
Bao, R., Wang, S., Feng, J., Duan, Y., Liu, K., Zhao, J., Liu, H., & Yang, J. (2024) · Energy & Fuels · doi:10.1021/acs.energyfuels.4c00240 · Cited by 69
Kraft lignin valorization: Biofuels and thermoset materials in focus
Lawoko, M., & Samec, J. S. M. (2022) · Current Opinion in Green and Sustainable Chemistry · doi:10.1016/j.cogsc.2022.100738 · Cited by 62
Moreira, W. M., Viotti, P. V., Vieira, M. G. A., Baptista, C. M. S. G., Scaliante, M. H. N. O., & Gimenes, M. L. (2020) · Colloids and Surfaces A Physicochemical and Engineering Aspects · doi:10.1016/j.colsurfa.2020.125597 · Cited by 37
Syed, M. W., Kazmi, W. W., Hussain, A., Shah, S. F. A., Kariim, I., Mehdi, A. M., Omer, A., Bhatti, A. H., Eze, F., & Bhatti, U. H. (2024) · Energy Conversion and Management · doi:10.1016/j.enconman.2024.118615 · Cited by 35
Curmi, H., Chirat, C., Roubaud, A., Peyrot, M., Haarlemmer, G. W., & Lachenal, D. (2021) · The Journal of Supercritical Fluids · doi:10.1016/j.supflu.2021.105489 · Cited by 31
Application of bio-based polyurethanes in construction: A state-of-the-art review
Zarmehr, S. P., Kazemi, M., Madasu, N. G. A., Lamanna, A. J., & Fini, E. H. (2024) · Resources Conservation and Recycling · doi:10.1016/j.resconrec.2024.107906 · Cited by 39
Kumar, A., Yadav, P., & Reddy, S. N. (2023) · Chemical Engineering Science · doi:10.1016/j.ces.2023.118548 · Cited by 36
From Pulp to Aromatic Products─Reaction Pathways of Lignin Depolymerization
Wörner, M., Barsuhn, A., Zevaco, T. A., Hornung, U., & Dahmen, N. (2024) · Energy & Fuels · doi:10.1021/acs.energyfuels.3c04509 · Cited by 27
Self-citationWang, X., He, J., Pang, S., Yao, S., Zhu, C., Zhao, J., Liu, Y., Liang, C., & Qin, C. (2022) · International Journal of Molecular Sciences · doi:10.3390/ijms23158612 · Cited by 30
Kumar, V., & Verma, P. (2024) · Journal of Environmental Management · doi:10.1016/j.jenvman.2024.121631 · Cited by 27
Senga, R., Nasr, M., Fujii, M., & Abdelhaleem, A. (2024) · Chemosphere · doi:10.1016/j.chemosphere.2024.143847 · Cited by 33
Wörner, M., Werner, L., Hornung, U., Islongo Canabarro, N., Baudouin, D., & Dahmen, N. (2024) · Energy & Fuels · doi:10.1021/acs.energyfuels.3c04737 · Cited by 21
Self-citationContinuous Extraction of Black Liquor Salts under Hydrothermal Conditions
Wang, R., Deplazes, R., Vogel, F., & Baudouin, D. (2021) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.0c05203 · Cited by 20
Self-citationModeling of Liquid–Vapor Phase Equilibria of Pyrolysis Bio-oils: A Review
Fonseca, F. G., & Funke, A. (2024) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.4c00775 · Cited by 23
Kozmelj, T. R., Bartolomei, E., Dufour, A., Leclerc, S., Arnoux, P., Likozar, B., Jasiukaitytė‐Grojzdek, E., Grilc, M., & Brech, Y. L. (2024) · Biomass and Bioenergy · doi:10.1016/j.biombioe.2024.107056 · Cited by 22
Park, S., Kim, J., Choi, J.-H., Kim, J.-C., Kim, J.-H., Cho, Y., Jung, S., Kwak, H. W., & Choi, I.-G. (2023) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2023.127472 · Cited by 21
Hamzeh, Y., Chirat, C., Haarlemmer, G. W., Lachenal, D., Ashori, A., Mortha, G. F., & Demey, H. (2023) · Chemical Engineering Journal · doi:10.1016/j.cej.2023.144269 · Cited by 17
Synthetic Lignin Oligomers: Analytical Techniques, Challenges, and Opportunities
Rojas, M., Fonseca, F. G., Hornung, U., Funke, A., & Dahmen, N. (2025) · ChemSusChem · doi:10.1002/cssc.202402334 · Cited by 18
Self-citationJia, Y., Wang, Y., Wang, M., Li, B., Song, X., Wu, M. C., Nong, G., & Yin, Y. (2023) · Industrial Crops and Products · doi:10.1016/j.indcrop.2023.117987 · Cited by 15
A Kraft Mill-Integrated Hydrothermal Liquefaction Process for Liquid Fuel Co-Production
Ong, B. H. Y., Walmsley, T. G., Atkins, M. J., & Walmsley, M. R. W. (2020) · Processes · doi:10.3390/pr8101216 · Cited by 14
On the selective desulphurization of biomass derivatives in supercritical water
Baudouin, D., Xiang, H., & Vogel, F. (2022) · Biomass and Bioenergy · doi:10.1016/j.biombioe.2022.106529 · Cited by 13
“The chemistry of various organosulphur compounds present in fossil crudes has been studied under various hydrothermal conditions [26,27].”
BackgroundSelf-citationLi, P., Wang, B., Hu, J., Chen, W., Fang, S., Chang, C., & Pang, S. (2024) · Journal of the Energy Institute · doi:10.1016/j.joei.2024.101618 · Cited by 14
Eco-friendly phenol formaldehyde resin wood adhesive from bagasse lignin liquefaction
Liu, J., Xie, E., Tang, Y., Feng, R., & Gan, W. (2023) · Sustainable Chemistry and Pharmacy · doi:10.1016/j.scp.2023.101129 · Cited by 19
Sindhuwati, C., Nahil, M. A., & Williams, P. T. (2025) · Biomass and Bioenergy · doi:10.1016/j.biombioe.2025.108456 · Cited by 13
Demirkaya, E., Cocero, M. J., & Cantero, D. A. (2024) · The Journal of Supercritical Fluids · doi:10.1016/j.supflu.2024.106296 · Cited by 11
Ahlbom, A., Maschietti, M., Nielsen, R. P., Lyckeskog, H. N., Hasani, M., & Theliander, H. (2021) · Energies · doi:10.3390/en14040932 · Cited by 13
Saari, J., Sermyagina, E., Kaikko, J., Haider, M., Hamaguchi, M., & Vakkilainen, E. K. (2021) · Energies · doi:10.3390/en14061550 · Cited by 12
Ma, H., Xu, L., Tian, Y., Jiao, A., Zhang, M., Li, S., & Chen, M. (2021) · Optical Materials Express · doi:10.1364/ome.430061 · Cited by 10
Ab initio study of nuclear quantum effects on sub- and supercritical water
Thomsen, B., & Shiga, M. (2021) · The Journal of Chemical Physics · doi:10.1063/5.0071857 · Cited by 10
Taboada, S., Clark, L., Lindberg, J., Tonjes, D. J., & Mahajan, D. (2021) · Energies · doi:10.3390/en14133834 · Cited by 11
Pola, L., Collado, S., Wörner, M., Hornung, U., & Díaz, M. (2023) · Journal of environmental chemical engineering · doi:10.1016/j.jece.2023.111040 · Cited by 9
“Because of this, there has been little interest in applying this process to Kraft black liquor and only small-scale reactors have been used, as shown by Lappalainen et al. [8] in their review.”
BackgroundMethodSelf-citationUnderstanding the relationship between acid precipitation and lignin odor in Kraft Black liquor
Amieva, E., Pola, L., Collado, S., Oulego, P., Calvo, P. Á., & Díaz, M. (2024) · Cleaner Chemical Engineering · doi:10.1016/j.clce.2024.100143 · Cited by 7
Hydrothermal depolymerization of different lignins: Insights into structures and reactivities
Lui, Y. W., Tao, Q., Akien, G. R., Yuen, A. K. L., Montoya, A., Chan, B., & Lui, M. Y.-Y. (2025) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2025.144293 · Cited by 10
On the hydrothermal depolymerisation of kraft lignin using glycerol as a capping agent
Ahlbom, A., Maschietti, M., Nielsen, R. P., Hasani, M., & Theliander, H. (2023) · Holzforschung · doi:10.1515/hf-2022-0146 · Cited by 6
Hybrid Gasoline Production from Black Liquor through Coprocessing
Melin, K., Strüven, J. O., Eidam, P., Appelt, J., Hummel, C., Armbruster, U., Chapelliere, Y., Mirodatos, C., Schuurman, Y., & Oasmaa, A. (2022) · Energy & Fuels · doi:10.1021/acs.energyfuels.2c01638 · Cited by 7
Self-citationPola, L., Collado, S., Wörner, M., Hornung, U., & Díaz, M. (2023) · Chemosphere · doi:10.1016/j.chemosphere.2023.139737 · Cited by 7
“Nevertheless, when it comes to Kraft black liquor, hydrothermal lique-faction has been studied to a much lesser extent and only at a laboratory scale in a batch way (Lappalainen et al., 2020).”
BackgroundSelf-citationMesoporous Zirconium Oxides and Cobalt Oxides for Selective Hydrodeoxygenation of Vanillin
Wang, X., Zhang, Y., Chen, J., & Xu, Y. (2024) · Catalysis Letters · doi:10.1007/s10562-023-04516-7 · Cited by 6
“%) of lignin pyrolysis products, if directly used as biofuel, will cause a series of problems, such as low energy density, unstable combustion, filter blockage, excessive corrosion, and pump failure[3, 10, 11].”
Du, F., Xian, X.-Q., Tang, P., & Li, Y. (2024) · Molecules · doi:10.3390/molecules29020347 · Cited by 7
“As shown in Figure 15, the products had These results imply that the main composition categories of the products were alike. relatively similar chemical The wide band at 3480 cm −1 was assigned to the combination and overlap of the stretching vibrations of O-H, =C-H, and N–”
BackgroundMethodInfluentialFrom black to green - A critical review of thermochemical valorization of black liquor
Liu, Q., Zhang, X., & Han, L. (2025) · Chemical Engineering Journal · doi:10.1016/j.cej.2025.165451 · Cited by 5
Aqueous phase recirculation in hydrothermal liquefaction: A critical review
Shah, A. A., Khan, M. I., Noonari, A. A., Jatoi, A. S., & Sandquist, J. (2025) · Biomass and Bioenergy · doi:10.1016/j.biombioe.2025.108612 · Cited by 7
Using guaiacol as a capping agent in the hydrothermal depolymerisation of kraft lignin
Ahlbom, A., Maschietti, M., Nielsen, R. P., Hasani, M., & Theliander, H. (2023) · Nordic Pulp & Paper Research Journal · doi:10.1515/npprj-2023-0013 · Cited by 4
Canabarro, N. I., Yeadon, D. J., Wörner, M., Hornung, U., Vogel, F., & Baudouin, D. (2024) · The Journal of Supercritical Fluids · doi:10.1016/j.supflu.2024.106230 · Cited by 8
“Since part of the organics could be converted into carbonates via decarboxylation [15], this additional carbonate increases the concentration of Type 2 salts inside the separator.”
BackgroundSelf-citationRecent Advances in Supercritical Water Gasification of Pulping Black Liquor for Hydrogen Production
Cao, C., Yu, L., Li, W., Liu, L., & Duan, P. (2022) · IntechOpen eBooks · doi:10.5772/intechopen.105566 · Cited by 7
Moagi, V. M., Maphoru, M. V., & Mabena, L. F. (2025) · Electrochimica Acta · doi:10.1016/j.electacta.2025.147019 · Cited by 4
Cardete, M. A., Kritzinger, L. R., Breakey, D., McGarry, D., Peña, C., & Orejas, A. (2024) · The Journal of Supercritical Fluids · doi:10.1016/j.supflu.2024.106235 · Cited by 4
McMichael, P. S., Hoque, M., dos Santos, F. B., French, V., & Foster, E. J. (2024) · Reaction Chemistry & Engineering · doi:10.1039/d3re00424d · Cited by 6
Hidd, C., Morales, G., Monsalves, N., et al. (2025) · Sustainability · doi:10.3390/su17104494 · Cited by 3
Plants: a sustainable platform for second-generation biofuels and biobased chemicals
Lopez, L., Alagna, F., Bianco, L., Bari, I. D., Fasano, C., Panara, F., & Perrella, G. (2021) · Elsevier eBooks · doi:10.1016/b978-0-12-822810-4.00003-8 · Cited by 7
Thermal treatment options for biosolids management: a critical review
Patel, S., Hakeem, I. G., Marzbali, M. H., Halder, P., Vuppaladadiyam, A. K., Kumar, L., Surapaneni, A., Sharma, A., Batstone, D. J., & Shah, K. V. (2025) · Environmental Science Water Research & Technology · doi:10.1039/d5ew00569h · Cited by 10
Hydrodynamic behavior and design implications in continuous-flow hydrothermal liquefaction systems
Cronin, D. J., dos Passos, J. S., Zacher, A. H., Kilgore, U. J., Schmidt, A. J., Fox, S., & Thorson, M. R. (2026) · Fuel · doi:10.1016/j.fuel.2026.138528 · Cited by 1
Energy-efficient and eco-friendly lignin catalysts for clean fuel production
Iqbal, S., Murtaza, H., Nazir, S., Hussaın, F., & Hassan, S. U. (2026) · Catalysis Reviews · doi:10.1080/01614940.2026.2677057 · Cited by 4
Methane Production Reduced by Lignin Derivatives in Pulping Wastewater: Inhibition of Free Hydrolase
Lei, J., Xu, Z. H., Chen, Y., Yu, G., Liu, Z., Wang, S., Zhang, J., Li, K., & Xie, L. (2024) · Fermentation · doi:10.3390/fermentation10050247 · Cited by 3
Wang, H., Han, X., Li, K., Li, H., Liu, M., Zeng, Y., & Xu, C. C. (2022) · IEEE Lasers and Electro-Optics Society Annual Meeting (LEOS) · doi:10.5006/c2022-18010 · Cited by 2
Special Issue “Hydrothermal Technology in Biomass Utilization & Conversion II”
Chiaramonti, D., Kruse, A., & Klemm, M. (2020) · Energies · doi:10.3390/en14010103 · Cited by 2
Rasool, T., Ansar, M., Ali, I., Ali, M., Jamal, A., Badshah, M., Huang, Z., & Urynowicz, M. A. (2023) · Environmental Science and Pollution Research · doi:10.1007/s11356-023-31576-4 · Cited by 1
Bio-lubricant production from black liquor as a sustainable biorefinery strategy
Demirkaya, E., Cantero, D. A., Tenorio‐Alfonso, A., Cortés-Triviño, E., Franco, J. M., & Cocero, M. J. (2024) · Biomass Conversion and Biorefinery · doi:10.1007/s13399-024-06326-2 · Cited by 4
“The paper and pulp industry, as reported by the International Energy Agency (IEA), annually produces approximately 170 million tons of black liquor (dry basis), with an additional 50–70 million tons attributed to lignin [2].”
Zhang, Z., & Shen, W. (2025) · International Journal of Green Energy · doi:10.1080/15435075.2025.2558928 · Cited by 1
“Among these, gasification, supercritical water gasification (SCWG), and supercritical water liquefaction (SCWL) have attracted attention for their ability to convert black liquor into energy with lower emissions and higher energy recovery rates (Lappalainen et al. 2020).”
Hydrodeoxygenation of Black Liquor HTL Oil Model Compounds in Supercritical Water
Rautiainen, S., Viertiö, T., Vuorio, N., Hyppönen, F., Meca, L., Kukula, P., & Lehtonen, J. S. (2026) · Reactions · doi:10.3390/reactions7010007 · Cited by 1
Kumar, R., Dhakal, S., Næss, G., & Sørensen, M. (2026) · Biomass Conversion and Biorefinery · doi:10.1007/s13399-026-07116-8 · Cited by 2
Bikane, K., Long, X., Altarooti, E., & Millán, M. (2026) · Energy & Fuels · doi:10.1021/acs.energyfuels.5c06626 · Cited by 1
Yang, Y., Fu, W., Zeng, H., et al. (2026) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.6c00923 · Cited by 1
Chitosan–Nanolignin Aerogel with Microneedles-Based Architecture Obtained from Spent Sulfite Liquor
Dima, Ş., Tritean, N., Capră, L., et al. (2023) · doi:10.3390/chemproc2023013012 · Cited by 1
“The energetic value of sulfite liquor is known, and thisis the main application; however, a higher degree of interest has emerged intothe separation and valorization of the diversity of biocomponents, including biodiesel, fertilizers, and adsorbents [1–5].”
Aida, T. M. (2022) · Biofuels and biorefineries · doi:10.1007/978-981-16-6162-4_11 · Cited by 2
Liang, C., Wang, X., He, J., Zhu, C., Zhao, J., Han, J., Qin, C., & Yao, S. (2022) · SSRN Electronic Journal · doi:10.2139/ssrn.4090177
Methanol Production from the Pulp Mills and Paper Industry
Saleem, A., Ali, S., & Liaqat, I. (2023) · Elsevier eBooks · doi:10.1016/b978-0-443-15740-0.00002-1
Thermochemical and Electrochemical Conversion of Black Liquor for Syngas Production
Chow, Y. N., & Foo, K. Y. (2024) · Elsevier eBooks · doi:10.1016/b978-0-443-15740-0.00018-5
Status and Applicability of Lignin Depolymerization Technology
Seo, U. J., Jo, Y.-T., & Park, J. (2025) · 대한환경공학회지 · doi:10.4491/ksee.2025.47.1.23 · Cited by 1
Abrofarakh, M., Zivdar, M., & Mohebbi‐Kalhori, D. (2025) · Thermal Science and Engineering Progress · doi:10.1016/j.tsep.2025.103696
ARJMAND, B., Wörner, M., Horung, U., Joronen, T., & Konttinen, J. (2026) · SSRN Electronic Journal · doi:10.2139/ssrn.6205969
Self-citationBiorefinery : lignin liquefaction to produce green aromatic chemicals
Bartolomei, E. (2021) · theses.fr (ABES) · doi:10.70675/765a332fzf1c2z400dzbe05ze0998b2691c4 · Cited by 1
Thermoconversion processes and graphitization mechanisms of lignin
Rigollet, S. (2025) · theses.fr (ABES) · doi:10.70675/f9d0899ez203cz4f2az9a5fza814f9c59e4c
Fundamentals of thermochemical conversion of biomass
Akintunde, S. B., Haq, Z. U., & Salaudeen, S. A. (2026) · Elsevier eBooks · doi:10.1016/b978-0-443-27680-4.00001-9
Role of microorganism: a critical foundation for biofuel production
Bharathy, K. P., Gayathri, S., Dhanvanti, G. P., & Rakesh, S. (2026) · Elsevier eBooks · doi:10.1016/b978-0-443-34229-5.00013-4
de Menezes, F. F., Kashiwagi, F. M., Silva, J. J., Gomes, G. R., Prata, R., de Moraes, M. R., Lima, A. F., da Silva, F. G., Rodriguez, R. P., Driemeier, C., et al. (2026) · Frontiers in Bioengineering and Biotechnology · doi:10.3389/fbioe.2026.1837262
Concentrated Solar Combined With Hydrothermal Treatment to Unlock Lignin Graphitization Mechanisms
Rigollet, S., Weiss-Hortala, E., Flamant, G., & Nzihou, A. (2026) · Global Challenges · doi:10.1002/gch2.70115 · Cited by 1
“%) as expected [ 14, 38 ].”
Nabhai, A., Wasson, O. C., Gu, H., Cai, Z., Park, H. E., Springstead, J. R., Wu, Q., & Li, J. (2026) · Frontiers in Environmental Chemistry · doi:10.3389/fenvc.2026.1895012
Solvent- and formaldehyde-free phenolic resin derived from salicyl alcohol
Zhao, B., Xing, X., Guo, J., Chen, J., Li, Y., Wang, S., & Jing, X. (2026) · Industrial Crops and Products · doi:10.1016/j.indcrop.2026.124349
Metadata
- Authors
- Lappalainen, J., Baudouin, D., Hornung, U., Schuler, J., Melin, K., Bjelić, S., Vogel, F., Konttinen, J., & Joronen, T.
- Affiliations
- Tampere University (FI)
- Paul Scherrer Institute (CH)
- Karlsruhe Institute of Technology (DE)
- VTT Technical Research Centre of Finland (FI)
- Corresponding author
- Lappalainen, Jukka
- ORCID
- Venue
- Energies
- Publisher
- MDPI AG
- Published
- 2020-06-28
- Volume
- 13
- Issue
- 13
- Pages
- 3309
- ISSN
- 1996-1073 (ISSN-L)
- OpenAlex
- W3037144356
- Cited by
- 87
- References
- 150
- Citations by year
- 2026: 13 · 2025: 12 · 2024: 20 · 2023: 17 · 2022: 10 · 2021: 12 · 2020: 3
- FWCI
- 3.30
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Energies (publishedVersion, cc-by)
- Repository KITopen (Karlsruhe Institute of Technology) (submittedVersion, cc-by)
- DORA PSI (Paul Scherrer Institute) (submittedVersion, cc-by)
- RePEc: Research Papers in Economics (submittedVersion)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Tampere University Institutional Repository (Tampere University) (submittedVersion, cc-by)
- KITopen (cc-by)
- Funders
- European Commission (884111)
- Topics
- Physical Sciences › Chemical Engineering › Process Chemistry and Technology › Subcritical and Supercritical Water Processes
- Physical Sciences › Energy › Fuel Technology › Thermochemical Biomass Conversion Processes
- Physical Sciences › Chemical Engineering › Process Chemistry and Technology › Lignin and Wood Chemistry
- Keywords
- hydrothermal liquefaction, black liquor, kraft lignin, lignin valorization, supercritical water, subcritical water, bio-oil, alkali metal salts, zirconia catalysts, residence time, reactor clogging
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-09-28, under version 3 of the claim definition (prompt extract-v3).
A second model labelled each claim on 2026-09-28 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.