CoChat

Use of Nanoparticle Enhanced Phase Change Material for Cooling of Surface Acoustic Wave Sensor

Open access
Abdollahzadeh Jamalabadi, Mohammad Yaghoub · 2021 · Fluids

The DOI matches its Crossref record; 21 of the 21 references it cites were found in a registry or an index.

Abstract

The use of resonators, filters, interdigital transducers (IDT) and stable sources in electronic industry is widespread today. One of the most used filters are the surface acoustic wave (SAW) type, which is mostly based on Rayleigh waves propagation on the surface. On the other hand, the use of Phase change materials (PCMs) is considered as a heat sink method in the field of thermal cooling of electronic circuits. Recent development in heat transfer is obtained by nanoparticle-enhanced PCM (NEPCM), which is a result of combining nanoparticles with PCMs. Increase of thermal conductivity of NEPCM in comparison with common PCM enhances the heat transfer rate. The aim of the current study is thermal management of SAW for the application of high frequency heating by phase change material. Melting of NEPCMs inside a rectangular cavity next to the SAW cell is used for the cooling purpose. Free convection heat transfer of a NEPCMs in an square cavity is modeled throughout the mass and momentum. Energy governing equations are solved by using the finite element method. Electrohydrodynamic (EHD) forces exist in natural convection heat transfer within the fluid part of the enclosure. The results also show that the NEPCM causes heat transfer improvement up to 10%.

Overview

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.3390/fluids6010031

Cites

21 of 21 references verified0 citation errors · 0 not checkable

Statistics

Figures

Figure 1 Top view of a typical of surface acoustic wave device, including input transducer, output transducer, and piezoelectric subtrace in a design.
Figure 1 Top view of a typical of surface acoustic wave device, including input transducer, output transducer, and piezoelectric subtrace in a design.CC-BY · From the PDF
Figure 2 Geometry of the unit cell of the proposed surface acoustic wave (SAW) unit cell where cooling system is interacted with electrical part.
Figure 2 Geometry of the unit cell of the proposed surface acoustic wave (SAW) unit cell where cooling system is interacted with electrical part.CC-BY · From the PDF
Image 3
CC-BY · From the PDF
Figure 4 First six modes of SAW problem with cooling: ( a ) mode 1, ( b ) mode 2, ( c ) mode 3, ( d ) mode 4, ( e ) mode 5, ( f ) mode 6.
Figure 4 First six modes of SAW problem with cooling: ( a ) mode 1, ( b ) mode 2, ( c ) mode 3, ( d ) mode 4, ( e ) mode 5, ( f ) mode 6.CC-BY · From the PDF
Figure 5 Electric potential: ( a ) mode 1, ( b ) mode 2, ( c ) mode 3, ( d ) mode 4, ( e ) mode 5, ( f ) mode 6.
Figure 5 Electric potential: ( a ) mode 1, ( b ) mode 2, ( c ) mode 3, ( d ) mode 4, ( e ) mode 5, ( f ) mode 6.CC-BY · From the PDF
Figure 6 Comparison of the results of current method with Jamaabadi and Park [18].
Figure 6 Comparison of the results of current method with Jamaabadi and Park [18].CC-BY · From the PDF
Figure 7 Temperature distribution in SAW with cooling at the initial steps of applying resonance power.
Figure 7 Temperature distribution in SAW with cooling at the initial steps of applying resonance power.CC-BY · From the PDF
Figure 8 Temperature distribution in SAW with cooling at higher power while cooling from top.
Figure 8 Temperature distribution in SAW with cooling at higher power while cooling from top.CC-BY · From the PDF
Figure 9 Initial condition of phase change material (PCM) cell: ( a ) contours of dimensionless temperature, ( b ) contours of dimensionless pressure, ( c ) velocity vector, ( d ) contours of velocity magnitude.
Figure 9 Initial condition of phase change material (PCM) cell: ( a ) contours of dimensionless temperature, ( b ) contours of dimensionless pressure, ( c ) velocity vector, ( d ) contours of velocity magnitude.CC-BY · From the PDF
Figure 10 Final condition of PCM cell: ( a ) contours of dimensionless temperature, ( b ) contours of dimensionless pressure, ( c ) velocity vector, ( d ) contours of velocity magnitude.
Figure 10 Final condition of PCM cell: ( a ) contours of dimensionless temperature, ( b ) contours of dimensionless pressure, ( c ) velocity vector, ( d ) contours of velocity magnitude.CC-BY · From the PDF
Figure 11 Time dependency of fluid volume fraction.
Figure 11 Time dependency of fluid volume fraction.CC-BY · From the PDF
Figure 12 Time dependency of maximum temperature.
Figure 12 Time dependency of maximum temperature.CC-BY · From the PDF

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Claims other papers make about this one

Each is checked against this paper’s own text: does it say what the citing paper says it does?

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cites

Show all 21 references

Cited by

Metadata

Authors
Abdollahzadeh Jamalabadi, M. Y.
Affiliations
Ship Engineering Department, School of Mechanical Engineering, Chabahar Maritime University, Chabahar 99717-56499, Iran
Venue
Fluids
Publisher
MDPI AG
Published
2021-01-08
Volume
6
Issue
1
Pages
31
ISSN
2311-5521 (ISSN-L)
OpenAlex
W3120614422
Cited by
15
References
21
Citations by year
2026: 3 · 2025: 2 · 2024: 1 · 2023: 4 · 2022: 1 · 2021: 4
FWCI
1.07
Type
journal article
Language
en
Open access
Locations
  • Fluids (publishedVersion, cc-by)
  • DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
Topics
  • Physical Sciences › Engineering › Mechanical Engineering › Phase Change Materials Research
  • Physical Sciences › Chemical Engineering › Fluid Flow and Transfer Processes › Nanofluid Flow and Heat Transfer
  • Physical Sciences › Engineering › Mechanical Engineering › Heat Transfer and Optimization
Keywords
nanoparticle-enhanced phase change materials, surface acoustic wave sensors, thermal management, heat sinks, natural convection heat transfer, electrohydrodynamic force, dielectric heating, melting, cavity enclosure, thermal conductivity enhancement, electronics cooling

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.