A Review on Geopolymer Technology for Lunar Base Construction
Open accessThe DOI matches its Crossref record; 47 of the 52 references it cites were found in a registry or an index; 13 of the 50 sources its claims cite were checked for support.
Abstract
Geopolymer is a synthetic amorphous aluminosilicate material that can be used as an inorganic binder to replace ordinary Portland cement. Geopolymer is produced by mixing aluminosilicate source materials with alkali activators and curing the mixture either at ambient or low temperatures. Geopolymer research for lunar-based construction is actively underway to enable astronauts to stay on the moon for long periods. This research has been spurred on by earnest discussions of in situ resource utilization (ISRU). Recent research shows that the lunar regolith simulant-based geopolymers have high application potential to protect astronauts from the harsh moon environment. However, not all the simulants perfectly reproduce the lunar regolith, and the characteristics of the lunar regolith vary depending on the site. Issues remain regarding the applicability of geopolymer technology to contribute to ISRU through an elaborate and systematic plan of experiments. In this paper, the potential of geopolymers is assessed as a lunar-based construction material with the latest research results. Future work to develop the lunar regolith-based geopolymer technology is also proposed.
Overview
CoChat Summary
## TL;DR
This review argues that geopolymers made from lunar regolith simulants have strong potential as lunar base construction materials because they can achieve sufficient strength, durability, and radiation shielding while supporting in situ resource utilization (ISRU). The paper also emphasizes that major practical challenges remain, especially simulant fidelity, moisture management, and curing under lunar environmental conditions.
## Key findings
- Lunar regolith is promising geopolymer feedstock because its major minerals include olivine, pyroxene, plagioclase, ilmenite, and silica, and the paper notes that more than one-third of lunar regolith may be glassy material useful as precursor.
- The paper states that approximately 6 MPa compressive strength is sufficient for lunar base construction, compared with 35 MPa for a one-story structure on Earth.
- In cited studies, lunar regolith simulant-based geopolymers cured in vacuum showed mixed results: compressive strength decreased by about 50% in one case, but other vacuum/high-temperature curing conditions improved strength; under lunar-like thermal cycling, residual strength was still at least 13 MPa.
- Cosmic radiation shielding results reported for JSC-1A-based geopolymer suggest adequacy for a 12-month stay with an equivalent dose of 5 cSv, and another simulation found 1 m of regolith-binder thickness would halve GCR dose.
## Methods
- Narrative review of recent literature on geopolymer technology for lunar base construction, focusing on mechanical properties, durability, and radiation shielding performance.
- The paper synthesizes studies using lunar regolith simulants, along with related precursor materials such as metakaolin, fly ash, tektite, and volcanic ash, to assess applicability to ISRU.
- Main analysis is qualitative comparison across prior experiments and simulations, including curing conditions, activator choice, thermal cycling, and shielding models.
## Limitations
- The paper states that lunar regolith simulants do not perfectly reproduce lunar regolith, and that regolith properties vary by landing site.
- It also states that much of the evidence relies on simulants rather than actual lunar regolith, which limits direct applicability.
- Evident from the text: the review does not report a new experiment or meta-analysis with pooled effect sizes; it is a synthesis of heterogeneous prior studies, so conclusions depend on studies that use different simulants, activators, curing schemes, and test conditions.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures
Verification
Claims the paper makes
7 Valid · 4 Not valid · 24 Not checked · 15 Own results and interpretations
At least one cited source doesn’t support this claim or points to a different paper, and none confirmed it — see the verdicts below.
In the paper
“On the other hand, geopolymers cured at slightly higher temperatures (30.7–99.6 °C) for 72 h were found to have higher strength when cured in a vacuum [3].”
§ A Review on Geopolymer Technology for Lunar Base Construction > 4. High Potential of Lunar Regolith Simulant-Based Geopolymers > 4.2. Compressive Strength and Durability of Lunar Regolith Simulant-Based Geopolymers
What the sources say
- Disputedcites [3] Zhou S. Zhu X. Lu C. Li F. Synthesis and characterization of geopolymer from lunar regolith simulant based on natural volcanic scoria Chin. J. Aeronaut. 2022 35 144 159 10.1016/j.cja.2020.06.014 sourceExperimental — accuracy not yet measured
Section 2.3.2 (page unavailable) says all specimens were cured at 90% relative humidity in an environmental chamber and tested after 7 or 28 days, not after 72 hours in a vacuum. Section 3.2 (page unavailable) reports strength results at 20, 40, 60 and 80 °C, but no vacuum comparison. (LLM, conf=0.88)
Checked by a reasoning model — may be wrong.
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Disputed
The sources with a verdict support this claim; the rest weren’t checked yet, have no full text we could read, or their verdicts aren’t rated yet.
In the paper
“With the correct formulation and proper curing process, the compressive strength of fly ash-based geopolymers can reach values ≥100 MPa [11,12,13,14,15].”
§ A Review on Geopolymer Technology for Lunar Base Construction > 2. Applicability of Geopolymers as a Lunar Base Construction Material > 2.1. Source Materials for Geopolymers
What the sources say
- Not checked — no full text of the sourcecites [11] Williams R. Hart R. van Riessen A. Quantification of the extent of reaction of metakaolin based geopolymers using XRD, SEM and EDS J. Am. Ceram. Soc. 2011 94 2663 2670 10.1111/j.1551-2916.2011.04410.x source
- Not checked — no full text of the sourcecites [12] Williams R. van Riessen A. Determination of the reactive component of fly ashes for geopolymer production using XRF and XRD Fuel 2010 89 3683 3692 10.1016/j.fuel.2010.07.031 source
- Not checked — no full text of the sourcecites [13] Rickard D.A.W. Williams R. Temuujin J. van Riessen A. Assessing the suitability of three Australian fly ashes as an aluminosilicate source for geopolymers in high temperature applications Mater. Sci. Eng. A 2011 528 3390 3397 10.1016/j.msea.2011.01.005 source
- Not checked — no full text of the sourcecites [14] Van Riessen A. Chen-Tan N. Beneficiation of Collie fly ash for synthesis of geopolymer. Part 2—Geopolymers Fuel 2013 106 569 575 10.1016/j.fuel.2012.11.070 source
- Supportedcites [15] Lee S. van Riessen A. Chon C.-M. Benefits of sealed-curing on compressive strength of fly ash-based geopolymers Materials 2016 9 598 10.3390/ma9070598 PMC5456872 28773720 source
The Conclusions report that the fly ash-based geopolymers in this study reached average compressive strengths of about 120–135 MPa after seven days of aging in airtight sealed moulds. They specify that this result applies to the fly ash and experimental conditions used, including sealed curing and aging. (LLM, conf=0.94)
plainstates a possible cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“The mechanical strength of one-part geopolymers was found to be comparable to that of two-part geopolymers prepared with liquid activators [46].”
§ A Review on Geopolymer Technology for Lunar Base Construction > 4. High Potential of Lunar Regolith Simulant-Based Geopolymers > 4.1. Selection of Alkali Activator In general, geopolymers are prepared by activating aluminosilicate source materials with high pH alkali hydroxides or silicates. The most commonly used activators are alkali hydroxides, such as caustic soda (NaOH) or potassium hydroxide (KOH), with the former more widely used as it is less expensive. In most studies of lunar regolith simulant-based geopolymer, caustic soda solution was solely used (Table 4). Activators made from a combination of soda solution and sodium silicate or potassium silicate were also used. The advantages of NaOH are that some crystalline aluminosilicate minerals are generally more soluble in NaOH than in KOH [41], in addition to the more readily dissolvable amorphous material. The greater the degree of Si and Al dissolution, the greater the potential strength of the geopolymer. However, NaOH’s high viscosity and solubility decrease rapidly as the temperature reduces [42], suggesting that mixing and curing times need to be carefully selected. In the case of KOH, the viscosity is lower than that of NaOH, and geopolymer prepared with KOH may be preferred in that it exhibits lower thermal expansion [43]. However, since K is larger than Na, it is more exothermic when dissolved in water [44], which needs to be managed when processing geopolymer. Sodium silicate solution, or water glass, is not always used alone as an activator but may be combined with caustic soda so that targeted Si/Al and Na/Al values can be achieved in the geopolymer. One-part geopolymer, instead of a conventional two-part geopolymer design, can be produced by adding free water to a mixture of powdered activator and geopolymer source material [45,46]. Solid sodium silicate, caustic soda powder, CaO, MgO, red mud, etc., may all be used as activators [43]. The mechanical strength of one-part geopolymers was found to be comparable to that of two-part geopolymers prepared with liquid activators [46]. On the moon, a one-part geopolymer manufacturing method would be more appropriate. It may be more suitable to use KOH rather than NaOH in that it can exhibit higher flowability during mixing and better heat resistance of the final geopolymer. Depending on the amount of reactive silica and alumina in the lunar regolith, optimization of mechanical properties, heat resistance and durability of the geopolymer will be possible by changing the targeted Si/Al ratio by selecting either sodium silicate or sodium aluminate powder as required.
What the sources say
- Partly supportedcites [46] Luukkonen T. Abdollahnejad Z. Yliniemi J. Kinnunen P. Illikainen M. One-part alkali-activated materials: A review Cem. Concr. Res. 2018 103 21 34 10.1016/j.cemconres.2017.10.001 sourceExperimental — accuracy not yet measured
Section 3 (page not available) compares compressive strength and reports that one-part geopolymers were weaker than similar two-part mixtures in some cases but stronger in others. This supports the possibility of comparable strength, but not an unqualified finding about mechanical strength generally; the comparison addresses compressive strength specifically. (LLM, conf=0.85)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“The flexural strength, however, showed a larger decrease of 49~70%, compared with a mild decrease in compressive strength [3].”
§ A Review on Geopolymer Technology for Lunar Base Construction > 4. High Potential of Lunar Regolith Simulant-Based Geopolymers > 4.2. Compressive Strength and Durability of Lunar Regolith Simulant-Based Geopolymers
What the sources say
- Could not verifycites [3] Zhou S. Zhu X. Lu C. Li F. Synthesis and characterization of geopolymer from lunar regolith simulant based on natural volcanic scoria Chin. J. Aeronaut. 2022 35 144 159 10.1016/j.cja.2020.06.014 sourceExperimental — accuracy not yet measured
Section 2.3.2 describes specimens cured at set temperatures, and Section 3.2 reports strengths after that curing. Neither those passages nor searches for thermal cycling and a 49–70% decrease found results for exposure to lunar surface temperature cycles, so the attributed decrease cannot be verified from our copy. (LLM, conf=0.76)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Could not verify
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Based on this value, it is clear that sufficient compressive strength of lunar regolith simulant-based geopolymers can be obtained when cured at ambient in the air (Table 4) [1,3,4,6,49].”
§ A Review on Geopolymer Technology for Lunar Base Construction > 4. High Potential of Lunar Regolith Simulant-Based Geopolymers > 4.2. Compressive Strength and Durability of Lunar Regolith Simulant-Based Geopolymers
What the sources say
- Not checked — no full text of the sourcecites [1] Mills J.N. Katzarova M. Wagner N.J. Comparison of lunar and Martian regolith simulant-based geopolymer cements formed by alkali-activation for in-situ resource utilization Adv. Space Res. 2022 69 761 777 10.1016/j.asr.2021.10.045 source
- Partly supportedcites [3] Zhou S. Zhu X. Lu C. Li F. Synthesis and characterization of geopolymer from lunar regolith simulant based on natural volcanic scoria Chin. J. Aeronaut. 2022 35 144 159 10.1016/j.cja.2020.06.014 sourceExperimental — accuracy not yet measured
Section 3.2 reports that a lunar-regolith-simulant geopolymer cured at 20 °C reached 18.5 MPa compressive strength after 28 days. But Section 2.3.2 specifies curing at 90% relative humidity in an environmental chamber, not simply in ambient air. The paper also does not establish that 18.5 MPa meets the citing sentence’s unspecified threshold for 'sufficient' strength. (LLM, conf=0.82)
- Not checked — no full text of the sourcecites [4] Montes C. Broussard K. Gongre M. Simicevic N. Mejia J. Tham J. Allouche E. Davis G. Evaluation of lunar regolith geopolymer binder as a radioactive shielding material for space exploration applications Adv. Space Res. 2015 56 1212 1221 10.1016/j.asr.2015.05.044 source
- Not checked — no full text of the sourcecites [6] Davis G. Montes C. Eklund S. Preparation of lunar regolith based geopolymer cement under heat and vacuum Adv. Space Res. 2017 59 1872 1885 10.1016/j.asr.2017.01.024 source
- Not checked — no full text of the sourcecites [49] Alexiadis A. Alberini F. Meyer M.E. Geopolymers from lunar and Martian soil simulants Adv. Space Res. 2017 59 490 495 10.1016/j.asr.2016.10.003 source
- Not matchedcites Table 4
This doesn’t read as a citation we can look up.
boostedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
20 more claims · 3 with their cited sources checked
Create a free account to see all 50 claims and to verify the 6 references still open.
- It may state two separate claims as one. 18
- Probably not a substantial claim. 10
Citations
Cites
Geopolymer technology: The current state of the art
Duxson, P., Fernández-Jiménez, A., Provis, J. L., Lukey, G. C., Palomo, A., & van Deventer, J. S. J. (2007) · Journal of Materials Science · doi:10.1007/s10853-006-0637-z · Cited by 4,742
The geopolymerisation of alumino-silicate minerals
Xu, H., & Van Deventer, J. S. J. (2000) · International Journal of Mineral Processing · doi:10.1016/s0301-7516(99)00074-5 · Cited by 1,876 · cited 5×
“In the case of KOH, the viscosity is lower than that of NaOH, and geopolymer prepared with KOH may be preferred in that it exhibits lower thermal expansion [43].”
BackgroundInfluentialOne-part alkali-activated materials: A review
Luukkonen, T., Abdollahnejad, Z., Yliniemi, J., Kinnunen, P., & Illikainen, M. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2017.10.001 · Cited by 1,456 · cited 2×
“One-part geopolymer, instead of a conventional two-part geopolymer design, can be produced by adding free water to a mixture of powdered activator and geopolymer source material [45,46].”
BackgroundBarbosa, V. F. F., MacKenzie, K. J. D., & Thaumaturgo, C. (2000) · International Journal of Inorganic Materials · doi:10.1016/s1466-6049(00)00041-6 · Cited by 1,128
3D lattice type fracture model for concrete
Lilliu, G., & van Mier, J. G. M. (2003) · Engineering Fracture Mechanics · doi:10.1016/s0013-7944(02)00158-3 · Cited by 433 · cited 4×
“Unlike the interfacial transition zone (ITZ) between cement and aggregate, which is the weakest part of ordinary Portland cement concrete [22], the ITZ in geopolymers is generally stronger [23].”
BackgroundInfluentialThe lunar regolith: Chemistry, mineralogy and petrology
Papike, J. J., Simon, S. B., & Laul, J. C. (1982) · Reviews of Geophysics · doi:10.1029/rg020i004p00761 · Cited by 345
Molecular water detected on the sunlit Moon by SOFIA
Honniball, C. I., Lucey, P. G., Li, S., Shenoy, S., Orlando, T. M., Hibbitts, C. A., Hurley, D. M., & Farrell, W. M. (2020) · Nature Astronomy · doi:10.1038/s41550-020-01222-x · Cited by 247 · cited 1×
“In 2020, observations from SOFIA, a joint observatory between NASA and the German Space Agency, were presented with clear evidence of water, for the first time, on the sunlit surface of the moon [36].”
MethodRickard, W. D. A., Williams, R., Temuujin, J., & van Riessen, A. (2011) · Materials Science and Engineering A · doi:10.1016/j.msea.2011.01.005 · Cited by 243 · cited 3×
“Advantages • Rapid strength gain • Higher chloride resistance • Acid and sulfate resistance [24,25] • Excellent fire resistance [13,26] • Impressive heat insulation • Superior acid resistance [24] • Frost resistance • Little or no alkali–silica reaction [27] • Strong ITZ [23] • Shorter setting time • Faster hardening…”
BackgroundFactors Affecting the Compressive Strength of Geopolymers: A Review
Castillo, H., Collado, H., Droguett, T., Sánchez, S., Vesely, M., Garrido, P., & Palma, S. (2021) · Minerals · doi:10.3390/min11121317 · Cited by 231
The thermal evolution of metakaolin geopolymers: Part 2 – Phase stability and structural development
Duxson, P., Lukey, G. C., & van Deventer, J. S. J. (2007) · Journal of Non-Crystalline Solids · doi:10.1016/j.jnoncrysol.2007.02.050 · Cited by 229 · cited 1×
“In the case of KOH, the viscosity is lower than that of NaOH, and geopolymer prepared with KOH may be preferred in that it exhibits lower thermal expansion [43].”
Background
Research works printed but not linked: 5
- Papike J.J. Ryder G. Shearer C.K. Lunar Materials Planetary Materials, Reviews in Mineralogy Pakike J.J. Mineralogical Society of America Washington, DC, USA 1998 Volume 36 5.1 5.23
- Gustafson R. JSC-1A Lunar regolith simulant production summary and lessons learned Proceedings of the Lunar Regolith Simulant Workshop Huntsville, AL, USA 17–20 March 2009
- Gourley J.T. Geopolymers in Australia J. Aust. Ceram. Soc. 2014 50 102 110
- Noble S. The lunar regolith Proceedings of the Lunar Regolith Simulant Workshop Huntsville, AL, USA 17–20 March 2009
- Casanova I. Feasibility study and applications of sulfur concrete for lunar base development: A preliminary study Proceedings of the 28th Annual Lunar and Planetary Science Conference Houston, TX, USA 17–21 March 1997 209
Cited by
Chemical fundamentals of geopolymers in sustainable construction
Madirisha, M. M., Dada, O. R., & Ikotun, B. D. (2024) · Materials Today Sustainability · doi:10.1016/j.mtsust.2024.100842 · Cited by 177
Kumar, S. G. K. M., Kinuthia, J. M., Oti, J. E., & Adeleke, B. O. (2025) · Materials · doi:10.3390/ma18163823 · Cited by 119
“While extraterrestrial applications, including in situ regolith-based lunar habitats, remain experimental [32,33], this review prioritizes terrestrial infrastructure applications relevant to sustainable urbanization and climate-resilient construction.”
Energy system and resource utilization in space: A state-of-the-art review
Wu, W., Shen, J., Kong, H., Yang, Y., Ren, E., Liu, Z., Wang, W., Dong, M., Han, L., Yang, C., et al. (2024) · The Innovation Energy · doi:10.59717/j.xinn-energy.2024.100029 · Cited by 44
Korniejenko, K., Pławecka, K., & Kozub, B. (2022) · Energies · doi:10.3390/en15249322 · Cited by 38
Yan, S. M., Huang, K. J., Zhang, F., et al. (2022) · Environmental Research · doi:10.1016/j.envres.2022.115141 · Cited by 23
Metadata
- Authors
- Lee, S., & van Riessen, A.
- Affiliations
- Korea Institute of Geoscience and Mineral Resources (KR)
- John de Laeter Centre, Curtin University, Perth, WA 6845, Australia
- Venue
- Materials
- Publisher
- MDPI AG
- Published
- 2022-06-27
- Volume
- 15
- Issue
- 13
- Pages
- 4516
- ISSN
- 1996-1944 (ISSN-L)
- PMC
- PMC9267385
- OpenAlex
- W4283660129
- Cited by
- 45
- References
- 52
- Citations by year
- 2026: 15 · 2025: 8 · 2024: 14 · 2023: 3 · 2022: 5
- FWCI
- 0.66
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Materials (publishedVersion, cc-by)
- PubMed Central (publishedVersion, cc-by)
- PubMed (publishedVersion)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- eSpace (Curtin University) (submittedVersion, cc-by)
- Funders
- Hanwha Aerospace
- Topics
- Physical Sciences › Engineering › Civil and Structural Engineering › Concrete and Cement Materials Research
- Physical Sciences › Engineering › Building and Construction › Innovations in Concrete and Construction Materials
- Physical Sciences › Earth and Planetary Sciences › Space and Planetary Science › Planetary Science and Exploration
- Keywords
- geopolymer, lunar base construction, lunar regolith simulant, in-situ resource utilization, alkaline activator, inorganic binders, low-temperature curing
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.

![Figure 2 Geopolymerization reaction based on the conceptual model of Duxson et al. (2007) [53].](https://figures.cochat.ai/paper-figures/c06945eb1c884369908158b9b2b21e84/a-review-on-geopolymer-technology-for-lunar-base-construction-figure-2.jpg)