The DOI matches its Crossref record; 70 of the 75 references it cites were found in a registry or an index; 8 of the 168 sources its claims cite were checked for support.
Review on the Comparison of the Chemical Reactivity of Cyanex 272, Cyanex 301 and Cyanex 302 for Their Application to Metal Separation from Acid Media
Open accessAbstract
Cyanex extractants, such as Cyanex 272, Cyanex 301, and Cyanex 302 have been commercialized and widely used in the extraction and separation of metal ions in hydrometallurgy. Since Cyanex 301 and Cyanex 302 are the derivatives of Cyanex 272, these extractants have similar functional groups. In order to understand the different extraction behaviors of these extractants, an understanding of the relationship between their structure and reactivity is important. We reviewed the physicochemical properties of these extractants, such as their solubility in water, polymerization degree, acidity strength, extraction performance of metal ions, and the interaction with diluent and other extractants on the basis of their chemical structure. Synthetic methods for these extractants were also introduced. This information is of great value in the synthesis of new kinds of extractants for the extraction of metals from a diverse medium. From the literature, the extraction and stripping characteristics of metals by Cyanex 272 and its derivatives from inorganic acids such as HCl, H2SO4, and HNO3 were also reviewed. The replacement of oxygen with sulfur in the functional groups (P = O to P = S group) has two opposing effects. One is to enhance their acidity and extractability due to an increase in the stability of metal complexes, and the other is to make the stripping of metals from the loaded Cyanex 301 difficult.
Overview
CoChat Summary
TL;DR
This review compares the chemical reactivity, synthesis, extraction, stripping, and degradation behavior of Cyanex 272, Cyanex 301, and Cyanex 302 for metal separation from acid media. Replacing oxygen with sulfur increases acidity and extractability but also makes stripping and stability more problematic, especially for Cyanex 301.
Key findings
- Water solubility increases in the order Cyanex 272 < Cyanex 302 < Cyanex 301, with values at 25 °C of 4.58 × 10⁻⁵ mol/L, 5.41 × 10⁻⁵ mol/L, and 28.4 × 10⁻⁵ mol/L, respectively.
- For Cu(II) extraction, the order is Cyanex 301 >> Cyanex 302 > Cyanex 272; Cu(II) extraction by Cyanex 301/302 involves redox reactions, reducing Cu(II) to Cu(I) and oxidizing the extractant to disulfides.
- Th(IV) extraction from HNO₃ and HCl follows Cyanex 272 > Cyanex 302 > Cyanex 301, but the order is reversed in sulfuric acid; proposed extracted species include Th(NO₃)₂R₂ and ThSO₄R₂.
- Sulfur substitution enhances acidity and extractability but makes stripping difficult: Ag(I) requires 16 M HNO₃ for complete stripping from Cyanex 301, and Cyanex 301/302 degrade in nitric acid; with TBP, only 10% of dithiophosphinic acid in Cyanex 301 remains after six weeks, with degradation rate order Cyanex 301 > Cyanex 302 > Cyanex 272.
Methods
- Design: narrative review comparing Cyanex 272, Cyanex 301, and Cyanex 302 on the basis of chemical structure, synthesis routes, physicochemical properties, and solvent-extraction behavior.
- Data: published literature on synthesis, acidity, solubility, self-association, diluent interactions, binary extractant mixtures, and metal extraction/stripping from HCl, H₂SO₄, and HNO₃ media; no new experimental data are reported.
- Analysis: qualitative and tabulated comparison of extraction orders, equilibrium constants, stripping agents, degradation pathways, and recycling performance across cited studies.
Limitations
- Stated: little information has been reported on the synthesis conditions of the extractants; there is no information about the mechanism of degradation in each case, and more fundamental research is needed.
- Stated: the mechanism of Cyanex 301 degradation by TBP is not known in each case.
- Evident: as a review, it provides no new experimental measurements, and its conclusions depend on the cited literature and qualitative comparisons.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
8 Valid · 4 Not valid · 119 Not checked · 43 Own results and interpretations
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“However, the extraction e ciency depends on the temperature and the polarity of the diluents.”
What the sources say
- Not checked — no full text of the sourcecites [7] Torkaman, 2017, Recovery of cobalt from spent lithium ion batteries by using acidic and basic extractants in solvent extraction process, Sep. Purif. Technol. source
- Partly supportedcites [29] Ali, 2011, Cyanex 302: An extractant for Fe(III) from Chloride Medium, Bangladesh J. Sci. Ind. Res. sourceExperimental — accuracy not yet measured
Our copy supports the temperature half: Results and Discussion (Fig. 5) reports that 'the distribution ratio is increased with increasing temperature' over 20-45 °C with ΔH = 9.95 kJ/mol (endothermic). It also supports a diluent dependence — Results and Discussion gives n-hexane (D=2.45) > kerosene (1.08) > toluene (0.82) > cyclohexane (0.53) > hexanol-1 (0.12), and the Abstract states 'Extraction ratio is found to be dependent on diluent used'. However, the paper nowhere attributes this dependence to the POLARITY of the diluents (searched: polarity, dielectric constant); it only ranks diluent identity and concludes kerosene next to n-hexane is best. The polarity framing is the citing authors' extrapolation, not a statement of this source. (LLM, conf=0.75)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Ahigh loading capacity of Cyanex 302 for Fe(III) (29.41 g Fe(III) / 100 g Cyanex 302) was obtained from a 1 M HCl solution [29].”
What the sources say
- Partly supportedcites [29] Ali, 2011, Cyanex 302: An extractant for Fe(III) from Chloride Medium, Bangladesh J. Sci. Ind. Res. sourceExperimental — accuracy not yet measured
The magnitude is exactly right: the Results and Discussion section states 'the loading capacity of Cyanex 302 toward Fe 3+ is 29.41 g Fe 3+ /100 g Cyanex 302' (also in the Abstract and Conclusion). However, the qualifier 'from a 1 M HCl solution' does not match how our copy describes the loading experiment: the Loading procedure and the Fig. 6 caption give the aqueous phase as 0.083 M Fe3+, 0.02 M H+ and 1.0 M Cl-, i.e. a 1 M chloride medium at low acidity (the Conclusion calls it '1 M chloride medium'), not 1 M HCl. The 1.0 M HCl condition in our copy belongs to the distribution-ratio vs initial [Fe3+] study (Fig. 1), not the loading measurement, so the cited sentence attaches the loading value to the wrong medium. (LLM, conf=0.80)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Cyanex 301 was employed to separate Pd(II) over Pt(IV) from hydrochloric acid solutions [33].”
What the sources say
- Partly supportedcites [33] Truong, H.T., Lee, M.S., and Son, S.H. (2017). Extraction of Palladium(II) from hydrochloride acid solution by solvent extraction with mixtures containing either Cyanex 301 or LIX63. Metals, 7. sourceExperimental — accuracy not yet measured
The Introduction (p. 1) does state that Cyanex 301, among a list of extractants, 'have been employed to separate Pd(II) from hydrochloric acid solutions in the presence of other metals', which supports the general Pd-from-HCl separation part of the claim. However, our copy contains no Pt(IV) extraction data, no Pd/Pt separation factor and no experiment separating Pd over Pt: the work's own experiments (Section 3.1) used synthetic Pd(II)-only solutions, and the Cyanex 301 results reported there concern Pd extraction into mixtures and the negligible stripping of Pd(II) owing to the strong Pd(II)–sulfur interaction. The specific 'over Pt(IV)' selectivity attributed here is not stated in this paper; the related Pd/Pt separation study appears only as a cited reference ([11] Truong & Lee, Miner. Eng. 2018, 'Separation of Pd(II) and Pt(IV) from hydrochloric acid solutions by solvent extraction with Cyanex 301 and LIX 63'). (LLM, conf=0.75)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“In general, the strong interaction between polar diluents and extractants leads to a decrease in the extraction e ciency of Co(II) [7,29].”
What the sources say
- Not checked — no full text of the sourcecites [7] Torkaman, 2017, Recovery of cobalt from spent lithium ion batteries by using acidic and basic extractants in solvent extraction process, Sep. Purif. Technol. source
- Partly supportedcites [29] Ali, 2011, Cyanex 302: An extractant for Fe(III) from Chloride Medium, Bangladesh J. Sci. Ind. Res. sourceExperimental — accuracy not yet measured
The diluent-effect paragraph in Results and Discussion supports only the general direction of the claim: with 0.01 M Cyanex 302 the extraction ratio falls as diluent polarity rises, n-hexane (D = 2.45) > kerosene (1.08) > toluene (0.82) > cyclohexane (0.53) > hexanol-1 (0.12), and the Abstract likewise states 'Extraction ratio is found to be dependent on diluent used.' However, that finding is for Fe3+ from (0.025 M H+ - 1.0 M Cl-) medium — searches for cobalt/Co(II) across our copy return nothing (the Introduction's survey of Cyanex 302 systems lists Zn, Ho, Y, Er, U, Zr, Pb, Cu, Sb, Bi, Fe, and the HSAB list of soft Class-B ions names Ni(II), Zn(II), Ag(I), Cu(I), Au(I), Pt(II) but not Co(II)), so the Co(II) part of the claim is not supported by this source. The paper also does not offer the mechanistic attribution the citing sentence carries (strong polar-diluent–extractant interaction); it only reports the observed diluent order and concludes kerosene/n-hexane are best. (LLM, conf=0.70)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“From the UV-VIS spectra data of the organic phase (before and after extraction as well as after stripping), it was reported that the organic solution of Cyanex 272 could be regenerated for Co(II) extraction [64].”
What the sources say
- Partly supportedcites [64] Quintero-Almanza, D., Gamiño-Arroyo, Z., Sánchez-Cadena, L.E., Gómez-Castro, F.I., Uribe-Ramírez, A.R., Aguilera-Alvarado, A.F., and Ocampo Carmona, L.M. (2019). Recovery of Cobalt from Spent Lithium-Ion Mobile Phone Batteries Using Liquid–Liquid Extraction. Batteries, 5. sourceExperimental — accuracy not yet measured
Our full-text copy does state that stripping serves to regenerate the extractant: in 'Calculation of Theoretical Stages' the authors write 'In order to regenerate the extractant and obtain a cobalt electrolyte solution for subsequent electrodeposition, the correlation between the concentration of cobalt in the aqueous phase ([Co]aq) and the organic phase ([Co]org) was defined by Equation (6)', with stripping at O/A = 1.5 in 1 mol/L H2SO4 (Figure 12 caption, Conclusions). However, no passage of our copy reports UV-VIS (or any optical) spectra of the organic phase before extraction, after extraction or after stripping — the only spectra in the paper are X-ray diffraction of the leached solids (Figure 6) — and the regeneration is framed as the purpose of the McCabe-Thiele stripping design, not as a spectroscopically demonstrated reuse of the Cyanex 272 solution for Co(II) extraction. Searches for 'UV-Vis', 'ultraviolet visible', 'spectrophotometer', 'FTIR/ATR organic phase' and 'regenerated reused extraction cycles' returned nothing of that kind. (LLM, conf=0.65)
hedged- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
96 more claims
Create a free account to see all 174 claims and to verify the 2 references still open.
- It may state two separate claims as one. 57
- Probably not a substantial claim. 26
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ 4.1.1. From Hydrochloric Acid Solutions
“while the same performance was obtained by 0.08 M Cyanex 301 at an equilibrium pH of 3.8 [25,26].”
§ 4.1.4. Stripping Characteristics
“| 0.08 MCyanex 302 | Kerosene | 0.1 Msodium chloride; 0.063 MCu(II); pH = 3.8 | Cu(II) | complete”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ 2.2.3. Cyanex 302 2.2.3. Cyanex 302
“In this case, the product contains dialkyldithioacid, (C8H17)2P(S)SH (Cyanex 302) whose potential impurities are (C8H17)3PO (byproduct of Reaction (2)) and dialkyl phosphines sulfide, (C8H17)2P(S)H.”
§ 1. Introduction
“Cyanex 301 (the main constituent is bis(2,4,4-trimethylpentyl) dithiophosphinic acid) is suitable for extracting zinc and other heavy metals, including platinum group metals [2,5,6].”
Citations
Cites
A critical review on solvent extraction of rare earths from aqueous solutions
Xie, F., Zhang, T. A., Dreisinger, D., & Doyle, F. (2014) · Minerals Engineering · doi:10.1016/j.mineng.2013.10.021 · Cited by 1,444
Solvent extraction characteristics of thiosubstituted organophosphinic acid extractants
Sole, K. C., & Hiskey, J. B. (1992) · Hydrometallurgy · doi:10.1016/0304-386x(92)90093-f · Cited by 200
Tait, B. K. (1993) · Hydrometallurgy · doi:10.1016/0304-386x(93)90047-h · Cited by 199
Solvent extraction of copper by Cyanex 272, Cyanex 302 and Cyanex 301
Sole, K. C., & Hiskey, J. B. (1995) · Hydrometallurgy · doi:10.1016/0304-386x(94)00023-v · Cited by 173
Separation of silver from photographic wastes by emulsion liquid membrane system
Othman, N., Mat, H., & Goto, M. (2006) · Journal of Membrane Science · doi:10.1016/j.memsci.2006.05.020 · Cited by 169
Torkaman, R., Asadollahzadeh, M., Torab-Mostaedi, M., & Ghanadi Maragheh, M. (2017) · Separation and Purification Technology · doi:10.1016/j.seppur.2017.06.023 · Cited by 133
The selective recovery of zinc with new thiophosphinic acids
RICKELTON, W. A., & BOYLE, R. J. (1990) · Solvent Extraction and Ion Exchange · doi:10.1080/07366299008918030 · Cited by 118 · cited 5×
“Structure and properties of Cyanex 272, Cyanex 302 and Cyanex 301 at 24 °C [10,13].”
BackgroundInfluentialSolvent Extraction with Organophosphines—Commercial & Potential Applications—
Rickelton, W. A., & Boyle, R. J. (1988) · Separation Science and Technology · doi:10.1080/01496398808075627 · Cited by 93
Solvent extraction separation of La from chloride solution containing Pr and Nd with Cyanex 272
Banda, R., Jeon, H. S., & Lee, M. S. (2012) · Hydrometallurgy · doi:10.1016/j.hydromet.2012.04.003 · Cited by 86
Self-citationKolařík, Z., & Pánková, H. (1966) · Journal of Inorganic and Nuclear Chemistry · doi:10.1016/0022-1902(66)80123-9 · Cited by 85
Research works printed but not linked: 4
- Adekola, 2009, Solvent Extraction of Cobalt and Nickel From Nigerian Lateritic Soil, J. Chem. Soc. Niger., 35, 123
- Lenhard, 2008, Extraction and separation of Cobalt and Nickel with extractants Cyanex 302, Cyanex 272 and their mixture, Kem. Ind., 57, 417
- Daoud, 2008, Solvent extraction of Zr(IV) from nitric acid solutions using CYANEX 272, CYANEX 301 and CYANEX 302, Sharm El-Sheikh Egypt, 9, 11
- Gajda, 2002, Equilibria of Cobalt (II) and Nickel (II) Extraction from Sulphate Solutions with Cyanex 301, Ars Sep. Acta, 1, 55
Cited by
Technology for the Recovery of Lithium from Geothermal Brines
Stringfellow, W. T., & Dobson, P. F. (2021) · Energies · doi:10.3390/en14206805 · Cited by 293
Meshram, P., Agarwal, N., & Abhilash, P. (2025) · RSC Advances · doi:10.1039/d4ra08429b · Cited by 38
Akbar, H., Javed, M. S., Iqbal, S. T., Khan, M. I., Anwar, T., Anjum, F., Ahmad, A., Muneeb, M., Ali, A., & Oh, W. (2024) · Journal of the Korean Ceramic Society · doi:10.1007/s43207-024-00365-1 · Cited by 34
Sulaiman, R. N. R., Othman, N., Jusoh, N., Noah, N. F. M., Rashid, R., & Saufi, S. M. (2021) · Chemical Engineering and Processing - Process Intensification · doi:10.1016/j.cep.2021.108581 · Cited by 19
Metadata
- Authors
- Nguyen, V. N. H., Nguyen, T. H., & Lee, M. S.
- Affiliations
- Mokpo National University (KR)
- Can Tho University (VN)
- Corresponding author
- Lee, Man Seung
- Venue
- Metals
- Publisher
- MDPI AG
- Published
- 2020-08-17
- Volume
- 10
- Issue
- 8
- Pages
- 1105
- ISSN
- 2075-4701 (ISSN-L)
- OpenAlex
- W3070043586
- Cited by
- 55
- References
- 75
- Citations by year
- 2026: 16 · 2025: 15 · 2024: 10 · 2023: 6 · 2022: 2 · 2021: 6
- FWCI
- 1.72
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Metals (publishedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Funders
- Korea Institute of Energy Technology Evaluation and Planning (20165010100880)
- Topics
- Physical Sciences › Materials Science › Metals and Alloys › Extraction and Separation Processes
- Physical Sciences › Chemistry › Inorganic Chemistry › Radioactive element chemistry and processing
- Physical Sciences › Chemistry › Analytical Chemistry › Analytical chemistry methods development
- Keywords
- Cyanex 272, Cyanex 301, Cyanex 302, structure-reactivity relationships, metal ion extraction, hydrometallurgy, extractant synthesis, degree of polymerization, metal complex stability, metal stripping
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (qwen3.8-omni-flash).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Review on the Comparison of the Chemical Reactivity of Cyanex 272, Cyanex 301 and Cyanex 302 for Their Application to Metal Separation from Acid Media. https://app.cochat.ai/papers/10.3390/met10081105
- The paper
- Nguyen, V. N. H., Nguyen, T. H., & Lee, M. S. (2020). Review on the Comparison of the Chemical Reactivity of Cyanex 272, Cyanex 301 and Cyanex 302 for Their Application to Metal Separation from Acid Media. Metals. https://doi.org/10.3390/met10081105
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.