CoChat

Palladium Supported on Porous Chitosan–Graphene Oxide Aerogels as Highly Efficient Catalysts for Hydrogen Generation from Formate

Open access
Anouar, Aicha, Katir, Nadia, El Kadib, Abdelkrim, Primo, Ana, García, Hermenegildo · 2019 · Molecules

The DOI matches its Crossref record; 29 of the 29 references it cites were found in a registry or an index; none of the 15 sources its claims cite is checked for support yet.

Abstract

Adsorption of Pd(NH3)42+ in preformed chitosan–graphene oxide (CS-GO) beads and their subsequent reduction with NaBH4 afford well-dispersed, high dispersion (~21%) of uniformly sized Pd nanoparticles (~1.7 nm). The resulting Pd/CS-GO exhibits interesting catalytic activity for hydrogen generation by ammonium formate decomposition. The optimal GO proportion of 7 wt% allows reaching, at 60 °C, a turnover frequency above 2200 h−1—being outstanding among the highest values reported for this process to date. Interestingly, no formation of CO or CH4 was detected. The catalyst did not leach, although it underwent gradual deactivation, probably caused by the increase in the Pd average size that became over 3 nm after three uses. Our results are relevant in the context of efficient on-board hydrogen generation from liquid organic hydrogen carriers in transportation.

Overview

CoChat Summary

TL;DR

Pd nanoparticles (~1.7 nm) were supported on porous chitosan–graphene oxide aerogel beads and used for hydrogen generation from ammonium formate. The optimal 7 wt% GO catalyst reached a turnover frequency of 2279 h−1 at 60 °C in methanol, with no detectable CO or CH4, but it deactivated gradually on reuse due to Pd particle growth.

Key findings

  • Pd/CS-GO catalysts had uniformly sized Pd nanoparticles with an average size of about 1.7 nm and a Pd dispersion of 21.14% measured by CO chemisorption.
  • The optimal GO proportion was 7 wt%; under methanol at 60 °C, the most active Pd/CS-GO2 catalyst achieved a TOF of 2279 h−1, described as among the highest reported for formate decomposition at moderate temperatures.
  • No detectable CO or CH4 was formed under the reaction conditions; Pd leaching into solution was negligible (<0.006% of initial total Pd), and a hot filtration test showed no H2 evolution after catalyst removal.
  • The catalyst deactivated gradually upon reuse; average Pd nanoparticle size increased from 1.7 nm in the fresh sample to 3.67 nm in the used Pd/CS-GO2 sample, attributed mainly to Pd agglomeration.

Methods

  • Pd/CS and Pd/CS-GO aerogel beads were prepared by coagulating acid chitosan solutions with NaOH, impregnating hydrogels with Pd(NH3)4Cl2, reducing with NaBH4 in ethanol, and drying with supercritical CO2; GO was added at 3, 7, and 12 wt% before bead formation.
  • Catalytic tests used 50 mg catalyst (2.5 wt% Pd) with 10 mL of 1 M ammonium formate (10 mmol) in a 130 mL vessel under stirring at 250 rpm and temperatures from 25 to 60 °C; gas products were analyzed by micro-GC.
  • TOF values were based on the amount of Pd and a metal dispersion value of 0.21 measured by CO adsorption; comparisons were made with commercial 10% Pd/AC.

Limitations

  • Stated: the catalyst deactivates upon reuse, mainly due to Pd agglomeration and particle growth associated with decreased CS porosity and surface area; further work is needed to increase catalyst stability by increasing rigidity.
  • Stated: conditions for complete NH4HCO2 decomposition and increased catalyst stability remain to be solved in future studies.
  • Stated: the reason for higher activity in methanol than in water is not fully understood, and further studies are necessary to identify the main solvent-related factors.
  • Evident from the text: CO2 evolution was below stoichiometric amounts, attributed to CO2 solubility in the liquid phase; ammonia formed during the reaction may deactivate Pd at high concentrations, as a control experiment with 10−1 M aqueous ammonia significantly decreased the initial reaction rate.

Model-written summary. Check it against the paper before relying on it.

Integrity signals

Registry

Crossref · 10.3390/molecules24183290

Cites

29 of 29 references verified0 citation errors · 0 not checkable

Statistics

Nothing to recompute.

Figures

Scheme 1 Illustration of the preparation procedure of Pd/CS and Pd/CS-GO (Pd NPs embedded in chitosan-graphene oxide beads) samples. (i) CS or CS-GO precipitation in NaOH solution to form beads; (ii) Impregnation of CS or CS-GO beads in Pd(NH3)4Cl2 solution followed by NaBH4 reduction; and (iii) supercritical CO2 drying of the spheres.
Scheme 1 Illustration of the preparation procedure of Pd/CS and Pd/CS-GO (Pd NPs embedded in chitosan-graphene oxide beads) samples. (i) CS or CS-GO precipitation in NaOH solution to form beads; (ii) Impregnation of CS or CS-GO beads in Pd(NH3)4Cl2 solution followed by NaBH4 reduction; and (iii) supercritical CO2 drying of the spheres.CC BY · PubMed Central
Figure 1 FESEM images of (a) Pd/CS, (b) Pd/CS-GO3, and (c) low resolution FESEM image and corresponding Energy-Dispersive X-Ray Spectroscopy (EDX) elemental analysis of elements for a bead of Pd/CS-GO2.
Figure 1 FESEM images of (a) Pd/CS, (b) Pd/CS-GO3, and (c) low resolution FESEM image and corresponding Energy-Dispersive X-Ray Spectroscopy (EDX) elemental analysis of elements for a bead of Pd/CS-GO2.CC BY · PubMed Central
Figure 2 Dark-Field Scanning Transmission Electron Microscopy (DF-STEM) images of (a) Pd/CS, (b) Pd/CS-GO1, (c) Pd/CS-GO2, and (d) Pd/CS-GO3. The insets show the histograms of corresponding particle size distribution.
Figure 2 Dark-Field Scanning Transmission Electron Microscopy (DF-STEM) images of (a) Pd/CS, (b) Pd/CS-GO1, (c) Pd/CS-GO2, and (d) Pd/CS-GO3. The insets show the histograms of corresponding particle size distribution.CC BY · PubMed Central
Figure 3 High resolution X-Ray Photoelectron Spectroscopy (XPS) peaks and their best deconvolution to individual components indicated for each of the elements present in Pd/CS-GO2.
Figure 3 High resolution X-Ray Photoelectron Spectroscopy (XPS) peaks and their best deconvolution to individual components indicated for each of the elements present in Pd/CS-GO2.CC BY · PubMed Central
Figure 4 Temporal profile of H2 generation from the NH4HCO2 aqueous solution catalyzed by Pd-CS at 25 °C, 40 °C and 60 °C. Reaction conditions: 10 mmoles of ammonium formate, 10 mL of milliQ water, and 11.75 µmol of Pd.
Figure 4 Temporal profile of H2 generation from the NH4HCO2 aqueous solution catalyzed by Pd-CS at 25 °C, 40 °C and 60 °C. Reaction conditions: 10 mmoles of ammonium formate, 10 mL of milliQ water, and 11.75 µmol of Pd.CC BY · PubMed Central
Figure 5 Temporal H2 evolution by NH4HCO2 decomposition catalyzed by Pd/CS, Pd/CS-GO2, Pd/CS-GO3, and 10% Pd/AC. Reaction conditions: 10 mmol of ammonium formate, 10 mL of H2O, 60 °C, and 11.75 µmol of Pd.
Figure 5 Temporal H2 evolution by NH4HCO2 decomposition catalyzed by Pd/CS, Pd/CS-GO2, Pd/CS-GO3, and 10% Pd/AC. Reaction conditions: 10 mmol of ammonium formate, 10 mL of H2O, 60 °C, and 11.75 µmol of Pd.CC BY · PubMed Central
Figure 6 Temporal H2 evolution upon reuse of Pd/CS catalyst either fresh or reused (once or two) catalyst. Reaction conditions: 10 mmol of ammonium formate, 10 mL of methanol, 60 °C, and 11.75 µmol of Pd.
Figure 6 Temporal H2 evolution upon reuse of Pd/CS catalyst either fresh or reused (once or two) catalyst. Reaction conditions: 10 mmol of ammonium formate, 10 mL of methanol, 60 °C, and 11.75 µmol of Pd.CC BY · PubMed Central
Figure 7 DF-STEM images of Pd/CS catalyst (a) after 24 h use at 40 °C and (b) after second use at 40 °C for NH4CO2 decomposition under the reaction conditions indicated in Figure 6. The inserts show Pd particle size distribution, observing a growth upon reuse.
Figure 7 DF-STEM images of Pd/CS catalyst (a) after 24 h use at 40 °C and (b) after second use at 40 °C for NH4CO2 decomposition under the reaction conditions indicated in Figure 6. The inserts show Pd particle size distribution, observing a growth upon reuse.CC BY · PubMed Central
Figure 8 Temporal profiles of H2 (a) and CO2 (b) evolution in the gas phase for the decomposition of NH4HCO2 catalyzed by Pd/CS, Pd/CS-GO1, Pd/CS-GO2, and Pd/CS-GO3. Reaction conditions: 10 mmoles of ammonium formate, 10 mL of methanol, 60 °C, and 11.75 µmoles of Pd.
Figure 8 Temporal profiles of H2 (a) and CO2 (b) evolution in the gas phase for the decomposition of NH4HCO2 catalyzed by Pd/CS, Pd/CS-GO1, Pd/CS-GO2, and Pd/CS-GO3. Reaction conditions: 10 mmoles of ammonium formate, 10 mL of methanol, 60 °C, and 11.75 µmoles of Pd.CC BY · PubMed Central
Figure 9 Temporal profiles of H2 generation from NH4HCO2 catalyzed by Pd/CS-GO2 in (a) methanol or water and (b) in methanol at 25 or 60 °C.
Figure 9 Temporal profiles of H2 generation from NH4HCO2 catalyzed by Pd/CS-GO2 in (a) methanol or water and (b) in methanol at 25 or 60 °C.CC BY · PubMed Central
Figure 10 Temporal H2 evolution upon reuse of Pd/CS-GO2: ■ 1st use; ● 2 nd use; ▲ 3rd use; and ▼ 4th use. Reaction conditions: 10 mmol of ammonium formate, 10mL of methanol, 60 °C, and 11.75 µmol of Pd.
Figure 10 Temporal H2 evolution upon reuse of Pd/CS-GO2: ■ 1st use; ● 2 nd use; ▲ 3rd use; and ▼ 4th use. Reaction conditions: 10 mmol of ammonium formate, 10mL of methanol, 60 °C, and 11.75 µmol of Pd.CC BY · PubMed Central
Figure 11 EDX of Pd/Cs.
Figure 11 EDX of Pd/Cs.CC BY · PubMed Central
Figure 12 EDX of Pd/CS-GO1.
Figure 12 EDX of Pd/CS-GO1.CC BY · PubMed Central
Figure 13 EDX of Pd/CS-GO3.
Figure 13 EDX of Pd/CS-GO3.CC BY · PubMed Central

Verification

Claims the paper makes

0 Valid · 1 Not valid · 10 Not checked · 41 Own results and interpretations

29 more claims

Create a free account to see all 52 claims and every source verdict.

See all claims — free account
  • It may state two separate claims as one. 14
  • The quote only partly states this claim. 2
  • Probably not a substantial claim. 5

Create a free account to see these claims.

Citations

Cites

Cited by

See all 30

Metadata

Authors
Anouar, A., Katir, N., El Kadib, A., Primo, A., & García, H.
Affiliations
  • Instituto de Tecnología Química, Consejo Superior de Investigaciones Científicas, Universitat Politècnica de València, Av. De los Naranjos s/n, 46022 Valencia, Spain
  • Euro-Mediterranean University of Fes (MA)
  • Euromed Research Center, Engineering Division, Euro-Med University of Fès (UEMF), Route de Meknes, Rond-point de Bensouda, 30070 Fès, Morocco
  • Consejo Superior de Investigaciones Científicas (ES)
Corresponding author
Primo, Ana
Venue
Molecules
Publisher
MDPI AG
Published
2019-09-10
Volume
24
Issue
18
Pages
3290
ISSN
1420-3049 (ISSN-L)
OpenAlex
W2973223517
Cited by
30
References
29
Citations by year
2026: 1 · 2025: 1 · 2024: 7 · 2023: 3 · 2022: 5 · 2021: 3 · 2020: 9 · 2019: 1
FWCI
1.62
Type
journal article
Language
en
Open access
Locations
  • Molecules (publishedVersion, cc-by)
  • PubMed Central (publishedVersion, cc-by)
  • PubMed (publishedVersion)
  • DIGITAL.CSIC (Spanish National Research Council (CSIC)) (submittedVersion, cc-by)
  • DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion)
  • RiuNet (Universitat Politècnica de València) (submittedVersion, cc-by-nc-nd)
Funders
  • Ministerio de Ciencia, Innovación y Universidades (Severo OIchoa, RTI2018-98237co2-1)
  • Generalitat Valenciana (Prometeo 2017-083)
  • University Euromediteerraneen Fes (Scholarship to A. A.)
Topics
  • Physical Sciences › Materials Science › Materials Chemistry › Hydrogen Storage and Materials
  • Physical Sciences › Chemistry › Organic Chemistry › Nanomaterials for catalytic reactions
  • Physical Sciences › Chemical Engineering › Process Chemistry and Technology › Carbon dioxide utilization in catalysis
Keywords
palladium nanoparticles, hydrogen production, liquid organic hydrogen carriers, supported metal catalysts, sodium borohydride reduction, catalyst dispersion, catalyst deactivation, on-board hydrogen production
MeSH terms
Adsorption, Catalysis, Formates, Graphite, Hydrogen, Palladium, Porosity, Chitosan, Nanoparticles

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

A language model drew the claims from the paper on 2026-10-11, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).

A second model labelled each claim on 2026-10-11 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.