Deformation of Poly-l-lactid acid (PLLA) under Uniaxial Tension and Plane-Strain Compression
Open accessThe DOI matches its Crossref record; 59 of the 59 references it cites were found in a registry or an index.
Abstract
The ability of PLLA, either amorphous or semicrystalline, to plastic deformation to large strain was investigated in a wide temperature range (Td = 70–140 °C). Active deformation mechanisms have been identified and compared for two different deformation modes—uniaxial drawing and plane-strain compression. The initially amorphous PLLA was capable of significant deformation in both tension and plane-strain compression. In contrast, the samples of crystallized PLLA were found brittle in tensile, whereas they proved to be ductile and capable of high-strain deformation when deformed in plane-strain compression. The main deformation mechanism identified in amorphous PLLA was the orientation of chains due to plastic flow, followed by strain-induced crystallization occurring at the true strain above e = 0.5. The oriented chains in amorphous phase were then transformed into oriented mesophase and/or oriented crystals. An upper temperature limit for mesophase formation was found below Td = 90 °C. The amount of mesophase formed in this process did not exceed 5 wt.%. An additional mesophase fraction was generated at high strains from crystals damaged by severe deformation. After the formation of the crystalline phase, further deformation followed the mechanisms characteristic for the semicrystalline polymer. Interlamellar slip supported by crystallographic chain slip has been identified as the major deformation mechanism in semicrystalline PLLA. It was found that the contribution of crystallographic slip increased notably with the increase in the deformation temperature. The most probable active crystallographic slip systems were (010)[001], (100)[001] or (110)[001] slip systems operating along the chain direction. At high temperatures (Td = 115–140 °C), the α→β crystal transformation was additionally observed, leading to the formation of a small fraction of β crystals.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Figures

















Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Fityk : a general-purpose peak fitting program
Wojdyr, M. (2010) · Journal of Applied Crystallography · doi:10.1107/s0021889810030499 · Cited by 2,804 · cited 1×
“The FITYK computer program, dedicated to diffraction peak-fitting [53,54], was used for this purpose.”
MethodFischer, E. W., Sterzel, H. J., & Wegner, G. (1973) · Kolloid-Zeitschrift und Zeitschrift für Polymere · doi:10.1007/bf01498927 · Cited by 1,704
Zhang, J., Tashiro, K., Tsuji, H., & Domb, A. J. (2008) · Macromolecules · doi:10.1021/ma0706071 · Cited by 913 · cited 10×
“Such bimodal melting was frequently observed in PLLA when Tc was between 100 ◦C and 120 ◦C [48,55].”
BackgroundInfluentialCrystal structure, conformation and morphology of solution-spun poly(L-lactide) fibers
Hoogsteen, W., Postema, A. R., Pennings, A. J., Ten Brinke, G., & Zugenmaier, P. (1990) · Macromolecules · doi:10.1021/ma00204a041 · Cited by 864 · cited 2×
“The crystal transformation from α to β was observed to occur upon tensile drawing [8] and solid-state extrusion [5,6], more efficiently at higher temperatures, larger draw ratios and/or higher draw rates [4].”
BackgroundBiodegradable materials of poly(l-lactic acid): 1. Melt-spun and solution-spun fibres
Eling, B., Gogolewski, S., & Pennings, A. J. (1982) · Polymer · doi:10.1016/0032-3861(82)90176-8 · Cited by 607 · cited 3×
“The crystals of the β-phase were first obtained by drawing fibers at high temperatures and high draw ratios [45].”
BackgroundDeformation mechanisms in crystalline polymers
Bowden, P. B., & Young, R. J. (1974) · Journal of Materials Science · doi:10.1007/bf00540553 · Cited by 551
Schugens, C., Maquet, V., Grandfils, C., Jérôme, R., & Teyssié, P. (1996) · Journal of Biomedical Materials Research · doi:10.1002/(sici)1097-4636(199604)30:4<543::aid-jbm13>3.0.co;2-i · Cited by 319
Stoclet, G., Seguela, R., Lefebvre, J.-M., & Rochas, C. (2010) · Macromolecules · doi:10.1021/ma101430c · Cited by 271
Strain-Induced Molecular Ordering in Polylactide upon Uniaxial Stretching
Stoclet, G., Seguela, R., Lefebvre, J. M., Elkoun, S., & Vanmansart, C. (2010) · Macromolecules · doi:10.1021/ma9024366 · Cited by 266 · cited 10×
“Similar positions of these halos were reported in the literature [24,34] The merging of the first two halos results in a broad scattering as in PET.”
BackgroundInfluentialGaleski, A., Bartczak, Z., Argon, A. S., & Cohen, R. E. (1992) · Macromolecules · doi:10.1021/ma00047a023 · Cited by 247 · cited 2×
“Such a signal is usually a signature of lamellae fragmentation and their restructuring into a new arrangement with the long period along FD [52,58,59].”
BackgroundSelf-citation
Cited by
The Use of Various Measurement Methods for Estimating the Fracture Energy of PLA (Polylactic Acid)
Gao, L., & Drozdov, A. D. (2022) · Materials · doi:10.3390/ma15238623 · Cited by 10
Woodbury, S. M., Swanson, W. B., Douglas, L., Niemann, D., & Mishina, Y. M. (2023) · Frontiers in Dental Medicine · doi:10.3389/fdmed.2023.1240397 · Cited by 7
“While PLLA has a high compressive and tensile strength, it is brittle and not amenable to deformation and recovery at the macro (defect), micro (pore), and nano (nanofiber) scales (13).”
Mandlule, A., Liu, Y., Schwanz, S., Pieper, Y., Scharf, H., Iskhakova, K., Conceição, A. L. C., Wieland, D. C. F., Zeller-Plumhoff, B., Toma, F. M., et al. (2026) · Materials Advances · doi:10.1039/d5ma00886g · Cited by 6
Kajornprai, T., Sringam, J., Seejuntuek, A., Kaewsuwan, D., Kamonsutthipaijit, N., Chio‐Srichan, S., Suppakarn, N., & Trongsatitkul, T. (2024) · Journal of Polymer Science · doi:10.1002/pol.20240703 · Cited by 7
Unveiling the Amorphous Phase Contribution to Shear Piezoelectric Properties of Polylactide
Shen, H., Charlon, S., & Samuel, C. (2025) · Macromolecules · doi:10.1021/acs.macromol.5c01023 · Cited by 2
Metadata
- Authors
- Vozniak, A., & Bartczak, Z.
- Affiliations
- Centrum Badań Molekularnych i Makromolekularnych Polskiej Akademii Nauk (PL)
- Corresponding author
- Bartczak, Zbigniew
- Venue
- Polymers
- Publisher
- MDPI AG
- Published
- 2021-12-17
- Volume
- 13
- Issue
- 24
- Pages
- 4432
- ISSN
- 2073-4360 (ISSN-L)
- PMC
- PMC8708863
- OpenAlex
- W4200576880
- Cited by
- 11
- References
- 59
- Citations by year
- 2026: 4 · 2025: 2 · 2024: 3 · 2023: 1 · 2022: 1
- FWCI
- 0.44
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Polymers (publishedVersion, cc-by)
- PubMed Central (publishedVersion, cc-by)
- PubMed (publishedVersion)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Topics
- Physical Sciences › Materials Science › Polymers and Plastics › Polymer crystallization and properties
- Physical Sciences › Materials Science › Biomaterials › biodegradable polymer synthesis and properties
- Physical Sciences › Materials Science › Metals and Alloys › Microstructure and mechanical properties
- Keywords
- poly(L-lactic acid), plastic deformation, uniaxial tension, plane strain compression, amorphous polymers, semicrystalline polymers, chain orientation, strain-induced crystallization, mesophase formation, deformation mechanisms, temperature dependence
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Deformation of Poly-l-lactid acid (PLLA) under Uniaxial Tension and Plane-Strain Compression. https://app.cochat.ai/papers/10.3390/polym13244432
- The paper
- Vozniak, A., & Bartczak, Z. (2021). Deformation of Poly-l-lactid acid (PLLA) under Uniaxial Tension and Plane-Strain Compression. Polymers. https://doi.org/10.3390/polym13244432
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.