Deformation of Poly-l-lactid acid (PLLA) under Uniaxial Tension and Plane-Strain Compression
Open accessThe DOI matches its Crossref record; 59 of the 59 references it cites were found in a registry or an index.
Abstract
The ability of PLLA, either amorphous or semicrystalline, to plastic deformation to large strain was investigated in a wide temperature range (Td = 70–140 °C). Active deformation mechanisms have been identified and compared for two different deformation modes—uniaxial drawing and plane-strain compression. The initially amorphous PLLA was capable of significant deformation in both tension and plane-strain compression. In contrast, the samples of crystallized PLLA were found brittle in tensile, whereas they proved to be ductile and capable of high-strain deformation when deformed in plane-strain compression. The main deformation mechanism identified in amorphous PLLA was the orientation of chains due to plastic flow, followed by strain-induced crystallization occurring at the true strain above e = 0.5. The oriented chains in amorphous phase were then transformed into oriented mesophase and/or oriented crystals. An upper temperature limit for mesophase formation was found below Td = 90 °C. The amount of mesophase formed in this process did not exceed 5 wt.%. An additional mesophase fraction was generated at high strains from crystals damaged by severe deformation. After the formation of the crystalline phase, further deformation followed the mechanisms characteristic for the semicrystalline polymer. Interlamellar slip supported by crystallographic chain slip has been identified as the major deformation mechanism in semicrystalline PLLA. It was found that the contribution of crystallographic slip increased notably with the increase in the deformation temperature. The most probable active crystallographic slip systems were (010)[001], (100)[001] or (110)[001] slip systems operating along the chain direction. At high temperatures (Td = 115–140 °C), the α→β crystal transformation was additionally observed, leading to the formation of a small fraction of β crystals.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Figures

















Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Fityk : a general-purpose peak fitting program
Wojdyr, M. (2010) · Journal of Applied Crystallography · doi:10.1107/s0021889810030499 · Cited by 2,804 · cited 1×
“The FITYK computer program, dedicated to diffraction peak-fitting [53,54], was used for this purpose.”
MethodFischer, E. W., Sterzel, H. J., & Wegner, G. (1973) · Kolloid-Zeitschrift und Zeitschrift für Polymere · doi:10.1007/bf01498927 · Cited by 1,704
Zhang, J., Tashiro, K., Tsuji, H., & Domb, A. J. (2008) · Macromolecules · doi:10.1021/ma0706071 · Cited by 913 · cited 10×
“Such bimodal melting was frequently observed in PLLA when Tc was between 100 ◦C and 120 ◦C [48,55].”
BackgroundInfluentialCrystal structure, conformation and morphology of solution-spun poly(L-lactide) fibers
Hoogsteen, W., Postema, A. R., Pennings, A. J., Ten Brinke, G., & Zugenmaier, P. (1990) · Macromolecules · doi:10.1021/ma00204a041 · Cited by 864 · cited 2×
“The crystal transformation from α to β was observed to occur upon tensile drawing [8] and solid-state extrusion [5,6], more efficiently at higher temperatures, larger draw ratios and/or higher draw rates [4].”
BackgroundBiodegradable materials of poly(l-lactic acid): 1. Melt-spun and solution-spun fibres
Eling, B., Gogolewski, S., & Pennings, A. J. (1982) · Polymer · doi:10.1016/0032-3861(82)90176-8 · Cited by 607 · cited 3×
“The crystals of the β-phase were first obtained by drawing fibers at high temperatures and high draw ratios [45].”
BackgroundDeformation mechanisms in crystalline polymers
Bowden, P. B., & Young, R. J. (1974) · Journal of Materials Science · doi:10.1007/bf00540553 · Cited by 551
Schugens, C., Maquet, V., Grandfils, C., Jérôme, R., & Teyssié, P. (1996) · Journal of Biomedical Materials Research · doi:10.1002/(sici)1097-4636(199604)30:4<543::aid-jbm13>3.0.co;2-i · Cited by 319
Stoclet, G., Seguela, R., Lefebvre, J.-M., & Rochas, C. (2010) · Macromolecules · doi:10.1021/ma101430c · Cited by 271
Strain-Induced Molecular Ordering in Polylactide upon Uniaxial Stretching
Stoclet, G., Seguela, R., Lefebvre, J. M., Elkoun, S., & Vanmansart, C. (2010) · Macromolecules · doi:10.1021/ma9024366 · Cited by 266 · cited 10×
“Similar positions of these halos were reported in the literature [24,34] The merging of the first two halos results in a broad scattering as in PET.”
BackgroundInfluentialGaleski, A., Bartczak, Z., Argon, A. S., & Cohen, R. E. (1992) · Macromolecules · doi:10.1021/ma00047a023 · Cited by 247 · cited 2×
“Such a signal is usually a signature of lamellae fragmentation and their restructuring into a new arrangement with the long period along FD [52,58,59].”
BackgroundSelf-citationSawai, D., Takahashi, K., Sasashige, A., Kanamoto, T., & Hyon, S.-H. (2003) · Macromolecules · doi:10.1021/ma030050z · Cited by 236 · cited 6×
“For semicrystalline PLLA, obtained either by cold crystallization prior to deformation or crystallizing just at the beginning of the deformation experiment (Td > 90 ◦C), the interlamellar slip (i.e., the shear in amorphous layers separating lamellae) was identified as the major deformation mechanism.”
BackgroundInfluentialEnthalpy of melting of α′- and α-crystals of poly(l-lactic acid)
Righetti, M. C., Gazzano, M., Di Lorenzo, M. L., & Androsch, R. (2015) · European Polymer Journal · doi:10.1016/j.eurpolymj.2015.07.024 · Cited by 215 · cited 1×
“[51] estimated ∆hm = 143 J/g for the α form, while 107 J/g for the α′ form.”
Wasanasuk, K., & Tashiro, K. (2011) · Polymer · doi:10.1016/j.polymer.2011.10.046 · Cited by 213
Synthesis, Structure and Properties of Poly(lactic acid)
(2018) · Advances in Polymer Science · doi:10.1007/978-3-319-64230-7 · Cited by 211
Deformation and damage upon stretching of degradable polymers (PLA and PCL)
Rezgui, F., Swistek, M., Hiver, J. M., G'Sell, C., & Sadoun, T. (2005) · Polymer · doi:10.1016/j.polymer.2005.03.116 · Cited by 171
Gao, X.-R., Li, Y., Huang, H.-D., Xu, J.-Z., Xu, L., Ji, X., Zhong, G.-J., & Li, Z.-M. (2019) · Macromolecules · doi:10.1021/acs.macromol.9b00932 · Cited by 165
A dislocation model for yield in polyethylene
Young, R. J. (1974) · Philosophical Magazine · doi:10.1080/14786439808206535 · Cited by 161 · cited 4×
“It seems justified, as the critical shear stress for slip in the polymer crystal (plastic resistance) decreases strongly with temperature [56].”
BackgroundInfluentialPlasticity of semicrystalline polymers
Bartczak, Z., & Galeski, A. (2010) · Macromolecular Symposia · doi:10.1002/masy.201050807 · Cited by 150 · cited 9×
“, the shear taking place in amorphous layers between lamellae [57,60], which proved to be the dominant mechanism Figure 16.”
BackgroundSelf-citationPreparation of oriented β‐form poly(L‐lactic acid) by solid‐state extrusion
Sawai, D., Takahashi, K., Imamura, T., Nakamura, K., Kanamoto, T., & Hyon, S. (2002) · Journal of Polymer Science Part B: Polymer Physics · doi:10.1002/polb.10076 · Cited by 141 · cited 5×
“For semicrystalline PLLA, obtained either by cold crystallization prior to deformation or crystallizing just at the beginning of the deformation experiment (Td > 90 ◦C), the interlamellar slip (i.e., the shear in amorphous layers separating lamellae) was identified as the major deformation mechanism.”
BackgroundInfluentialCicero, J. A., & Dorgan, J. R. (2001) · Journal of Polymers and the Environment · doi:10.1023/a:1016012818800 · Cited by 140
Influence of biaxial stretching mode on the crystalline texture in polylactic acid films
Ou, X., & Cakmak, M. (2008) · Polymer · doi:10.1016/j.polymer.2008.09.053 · Cited by 139 · cited 1×
“It was found that the deformation conditions, such as temperature of deformation, deformation rate, or final strain, seriously affect the structural evolution of PLLA and the resulting mechanical properties; for example, when deformation is performed at a temperature above Tg, but below the cold crystallization temper…”
BackgroundJariyasakoolroj, P., Tashiro, K., Wang, H., Yamamoto, H., Chinsirikul, W., Kerddonfag, N., & Chirachanchai, S. (2015) · Polymer · doi:10.1016/j.polymer.2015.05.006 · Cited by 125
Crystal transformation from the α- to the β-form upon tensile drawing of poly(l-lactic acid)
Takahashi, K., Sawai, D., Yokoyama, T., Kanamoto, T., & Hyon, S. (2004) · Polymer · doi:10.1016/j.polymer.2004.03.108 · Cited by 124 · cited 9×
“For semicrystalline PLLA, obtained either by cold crystallization prior to deformation or crystallizing just at the beginning of the deformation experiment (Td > 90 ◦C), the interlamellar slip (i.e., the shear in amorphous layers separating lamellae) was identified as the major deformation mechanism.”
BackgroundInfluentialTábi, T., Ageyeva, T., & Kovács, J. G. (2021) · Polymer Testing · doi:10.1016/j.polymertesting.2021.107282 · Cited by 119 · cited 4×
“The big endothermic peak actually consists of two overlapping peaks, which are due to recrystallization (α′→α) and the melting of crystals of the α form, respectively [55].”
BackgroundInfluentialStructure evolution of α′‐phase poly(lactic acid)
Chen, X., Kalish, J. P., & Hsu, S. L. (2011) · Journal of Polymer Science Part B Polymer Physics · doi:10.1002/polb.22327 · Cited by 109
Zhang, X., Schneider, K., Liu, G., Chen, J., Brüning, K., Wang, D., & Stamm, M. (2011) · Polymer · doi:10.1016/j.polymer.2011.07.003 · Cited by 108 · cited 1×
“It was found that the deformation conditions, such as temperature of deformation, deformation rate, or final strain, seriously affect the structural evolution of PLLA and the resulting mechanical properties; for example, when deformation is performed at a temperature above Tg, but below the cold crystallization temper…”
BackgroundWAXS study of the structural reorganization of semi-crystalline polylactide under tensile drawing
Stoclet, G., Séguéla, R., Vanmansart, C., Rochas, C., & Lefebvre, J. (2011) · Polymer · doi:10.1016/j.polymer.2011.11.063 · Cited by 101 · cited 8×
“α crystals and subsequent reorganization into mesophase and/or α′ crystals, depending on the temperature of deformation, was observed at high strains [25].”
BackgroundInfluentialIn-situ SAXS study of the plastic deformation behavior of polylactide upon cold-drawing
Stoclet, G., Lefebvre, J. M., Séguéla, R., & Vanmansart, C. (2014) · Polymer · doi:10.1016/j.polymer.2014.02.010 · Cited by 94
Wang, H., Zhang, J., & Tashiro, K. (2017) · Macromolecules · doi:10.1021/acs.macromol.7b00272 · Cited by 93 · cited 3×
“[3] argued that the δ-form (α′) is a crystalline phase independent of the α form, not a simple disordered modification of the α form.”
BackgroundInfluentialStructure development and biodegradability of uniaxially stretched poly(l-lactide)
Lee, J. K., Lee, K. H., & Jin, B. S. (2001) · European Polymer Journal · doi:10.1016/s0014-3057(00)00213-5 · Cited by 91
Chen, Y., Han, L., Ju, D., Liu, T., & Dong, L. (2018) · Polymer · doi:10.1016/j.polymer.2018.02.032 · Cited by 89
Zhang, X., Schneider, K., Liu, G., Chen, J., Brüning, K., Wang, D., & Stamm, M. (2011) · Polymer · doi:10.1016/j.polymer.2011.12.002 · Cited by 84
Lv, R., Na, B., Tian, N., Zou, S., Li, Z., & Jiang, S. (2011) · Polymer · doi:10.1016/j.polymer.2011.08.023 · Cited by 83 · cited 1×
“Moreover, at low temperatures close to Tg, drawing of PLLA frequently leads to formation of mesophase with molecular order lower than in crystals [9,24,29,30].”
BackgroundImprovement of the mechanical properties of poly( D , L ‐lactide) by orientation
Grijpma, D. W., Altpeter, H., Bevis, M. J., & Feijén, J. (2002) · Polymer International · doi:10.1002/pi.988 · Cited by 81
Crystal Polymorphism and Morphology of Polylactides
Lotz, B. (2017) · Advances in polymer science · doi:10.1007/12_2016_15 · Cited by 70 · cited 8×
“, increased growth rate, thicker lamellae, and some structural disorder) [2,46].”
BackgroundInfluentialBrittle-to-ductile transition of PLA induced by macromolecular orientation
Xu, S., Tahon, J., de Waele, I., Stoclet, G., & Gaucher, V. (2020) · eXPRESS Polymer Letters · doi:10.3144/expresspolymlett.2020.84 · Cited by 64
Wu, J., Yen, M., Wu, C., Li, C., & Kuo, M. C. (2012) · Journal of Polymers and the Environment · doi:10.1007/s10924-012-0523-5 · Cited by 61
Rangari, D., & Vasanthan, N. (2012) · Macromolecules · doi:10.1021/ma301482j · Cited by 60
Ou, X., & Çakmak, M. (2009) · Polymer · doi:10.1016/j.polymer.2009.11.058 · Cited by 59
Mechanical properties and structure of the zone-drawn poly(L-lactic acid) fibers
Okuzaki, H., Kubota, I., & Kunugi, T. (1999) · Journal of Polymer Science Part B Polymer Physics · doi:10.1002/(sici)1099-0488(19990515)37:10<991::aid-polb4>3.0.co;2-t · Cited by 52 · cited 1×
“The deformation behavior of PLLA was studied mostly in tensile deformation modes— uniaxial [4,9,10,12,19–37] and biaxial drawing [13,14,38–42], although other deformation modes, such as zone-drawing [43], die-drawing [44], solid-state extrusion [5–7,16,17] or plane-strain compression [18] were also explored.”
BackgroundPlastic Deformation of Amorphous Poly( l / dl -lactide): Structure Evolution and Physical Properties
Pluta, M., & Gałęski, A. (2007) · Biomacromolecules · doi:10.1021/bm061229v · Cited by 50 · cited 2×
“The diffraction observed in the discussed range was assigned in the past to the development of crystals oriented along FD [18] or to the contribution of the amorphous phase strongly oriented along FD—the third amorphous halo at 2Θ ≈ 31◦ arising from the characteristic interchain spacing of the methyl group in PLLA thr…”
BackgroundBartczak, Z. (2005) · Polymer · doi:10.1016/j.polymer.2005.07.096 · Cited by 50
Self-citationIlter, S., Hazer, B., Borcaklı, M., & Atıcı, O. (2001) · Macromolecular Chemistry and Physics · doi:10.1002/1521-3935(20010701)202:11<2447::aid-macp2447>3.0.co;2-6 · Cited by 49
Tanaka, M., & Young, R. J. (2006) · Macromolecules · doi:10.1021/ma0526286 · Cited by 48 · cited 1×
“Generally, crystal rotations and slip were proposed as active deformation mechanisms [22,23].”
BackgroundLi, J., Li, Z., Ye, L., Zhao, X., Coates, P. D., Caton‐Rose, F., & Martyn, M. (2017) · European Polymer Journal · doi:10.1016/j.eurpolymj.2017.03.005 · Cited by 47 · cited 1×
“The deformation behavior of PLLA was studied mostly in tensile deformation modes— uniaxial [4,9,10,12,19–37] and biaxial drawing [13,14,38–42], although other deformation modes, such as zone-drawing [43], die-drawing [44], solid-state extrusion [5–7,16,17] or plane-strain compression [18] were also explored.”
BackgroundOrientation and structure development in poly(lactide) under uniaxial deformation
Wong, Y. S., Stachurski, Z. H., & Venkatraman, S. S. (2008) · Acta Materialia · doi:10.1016/j.actamat.2008.06.027 · Cited by 46 · cited 1×
“Generally, crystal rotations and slip were proposed as active deformation mechanisms [22,23].”
BackgroundSawai, D., Yokoyama, T., Kanamoto, T., Sungil, M., Hyon, S., & Myasnikova, L. P. (2006) · Macromolecular Symposia · doi:10.1002/masy.200651015 · Cited by 44 · cited 1×
“[7] demonstrated that α form crystals gradually transform into β-form crystals, and the relative amount of the β-form crystals increases with increasing drawing temperature from 80 ◦C to 140 ◦C, reaching a maximum (approx.”
BackgroundLotz, B. (2015) · ACS Macro Letters · doi:10.1021/acsmacrolett.5b00205 · Cited by 40 · cited 3×
“, increased growth rate, thicker lamellae, and some structural disorder) [2,46].”
BackgroundBillimoria, K., Heeley, E. L., Parsons, N., & Figiel, Ł. (2018) · European Polymer Journal · doi:10.1016/j.eurpolymj.2018.01.031 · Cited by 38 · cited 4×
“[37] assigned the peak located above 32◦ to the (018)α′ plane instead of to (1010).”
BackgroundInfluentialWAXS/SAXS study of plastic deformation instabilities and lamellae fragmentation in polyethylene
Bartczak, Z., & Vozniak, A. (2019) · Polymer · doi:10.1016/j.polymer.2019.05.076 · Cited by 38 · cited 4×
“At the same time, in the deformed samples, a clear reduction in the content of the crystalline phase was observed, which may indicate that, in addition to the mesophase, which was probably formed from oriented amorphous chains, the other fraction, appearing at higher strains, was probably formed from still oriented sm…”
BackgroundSelf-citationDeformation Instabilities and Lamellae Fragmentation during Deformation of Cross-linked Polyethylene
Bartczak, Z., & Vozniak, A. (2019) · Polymers · doi:10.3390/polym11121954 · Cited by 33 · cited 4×
“At the same time, in the deformed samples, a clear reduction in the content of the crystalline phase was observed, which may indicate that, in addition to the mesophase, which was probably formed from oriented amorphous chains, the other fraction, appearing at higher strains, was probably formed from still oriented sm…”
BackgroundSelf-citationZhuo, R., Zhang, Y., Li, G., Shao, C., Wang, Y., Liu, C., Li, Q., Cao, W., & Shen, C. (2016) · Vibrational Spectroscopy · doi:10.1016/j.vibspec.2016.08.001 · Cited by 31
Liu, J., Zhang, S., Zhang, L., Liu, L., & Bai, Y. (2014) · European Polymer Journal · doi:10.1016/j.eurpolymj.2014.08.021 · Cited by 30 · cited 1×
“Similar positions of these halos were reported in the literature [24,34] The merging of the first two halos results in a broad scattering as in PET.”
BackgroundThree-dimensional orientation of poly( l -lactide) crystals under uniaxial drawing
Lizundia, E., Larrañaga, A., Vilas‐Vilela, J. L., & León, L. M. (2016) · RSC Advances · doi:10.1039/c5ra22680e · Cited by 25
Strain-induced structural evolution of Poly(l-lactide) and Poly(d-lactide) blends
Stoclet, G. (2016) · Polymer · doi:10.1016/j.polymer.2016.07.019 · Cited by 19
Tanaka, M., & Young, R. J. (2006) · Biomacromolecules · doi:10.1021/bm060326l · Cited by 19
Ramachandran, K., Miscioscia, R., Filippo, G., Pandolfi, G., Luccio, T. D., & Kornfield, J. A. (2018) · Polymers · doi:10.3390/polym10030288 · Cited by 17
Crystallization and Mechanical Propertiesof Poly (D, L) Lactide-based Blown Films
Stoclet, G., Elkoun, S., Gaucher, V., Séguéla, R., & Lefebvre, J. (2007) · International Polymer Processing · doi:10.3139/217.2066 · Cited by 16
Lv, R., Zou, S., Na, B., Deng, H., & Yu, Z. (2013) · Polymer Engineering and Science · doi:10.1002/pen.23525 · Cited by 13 · cited 1×
“Moreover, at low temperatures close to Tg, drawing of PLLA frequently leads to formation of mesophase with molecular order lower than in crystals [9,24,29,30].”
Background
Cited by
The Use of Various Measurement Methods for Estimating the Fracture Energy of PLA (Polylactic Acid)
Gao, L., & Drozdov, A. D. (2022) · Materials · doi:10.3390/ma15238623 · Cited by 10
Woodbury, S. M., Swanson, W. B., Douglas, L., Niemann, D., & Mishina, Y. M. (2023) · Frontiers in Dental Medicine · doi:10.3389/fdmed.2023.1240397 · Cited by 7
“While PLLA has a high compressive and tensile strength, it is brittle and not amenable to deformation and recovery at the macro (defect), micro (pore), and nano (nanofiber) scales (13).”
Mandlule, A., Liu, Y., Schwanz, S., Pieper, Y., Scharf, H., Iskhakova, K., Conceição, A. L. C., Wieland, D. C. F., Zeller-Plumhoff, B., Toma, F. M., et al. (2026) · Materials Advances · doi:10.1039/d5ma00886g · Cited by 6
Kajornprai, T., Sringam, J., Seejuntuek, A., Kaewsuwan, D., Kamonsutthipaijit, N., Chio‐Srichan, S., Suppakarn, N., & Trongsatitkul, T. (2024) · Journal of Polymer Science · doi:10.1002/pol.20240703 · Cited by 7
Unveiling the Amorphous Phase Contribution to Shear Piezoelectric Properties of Polylactide
Shen, H., Charlon, S., & Samuel, C. (2025) · Macromolecules · doi:10.1021/acs.macromol.5c01023 · Cited by 2
Metadata
- Authors
- Vozniak, A., & Bartczak, Z.
- Affiliations
- Centrum Badań Molekularnych i Makromolekularnych Polskiej Akademii Nauk (PL)
- Corresponding author
- Bartczak, Zbigniew
- Venue
- Polymers
- Publisher
- MDPI AG
- Published
- 2021-12-17
- Volume
- 13
- Issue
- 24
- Pages
- 4432
- ISSN
- 2073-4360 (ISSN-L)
- PMC
- PMC8708863
- OpenAlex
- W4200576880
- Cited by
- 11
- References
- 59
- Citations by year
- 2026: 4 · 2025: 2 · 2024: 3 · 2023: 1 · 2022: 1
- FWCI
- 0.44
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Polymers (publishedVersion, cc-by)
- PubMed Central (publishedVersion, cc-by)
- PubMed (publishedVersion)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Topics
- Physical Sciences › Materials Science › Polymers and Plastics › Polymer crystallization and properties
- Physical Sciences › Materials Science › Biomaterials › biodegradable polymer synthesis and properties
- Physical Sciences › Materials Science › Metals and Alloys › Microstructure and mechanical properties
- Keywords
- poly(L-lactic acid), plastic deformation, uniaxial tension, plane strain compression, amorphous polymers, semicrystalline polymers, chain orientation, strain-induced crystallization, mesophase formation, deformation mechanisms, temperature dependence
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.